Kenwood TK-2360 User Manual 1

Kenwood TK-2360 Manual

Get Kenwood TK-2360 PDF manuals and user guides View all Kenwood TK-2360 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-2360 manual content summary:

  • Kenwood TK-2360 | User Manual 1 - Page 1
    INSTRUCTION MANUAL VHF FM TRANSCEIVER TK-2360 UHF FM TRANSCEIVER TK-3360 © B62-2209-00 (C) 09 08 07 06 05 04 03 02 01 00
  • Kenwood TK-2360 | User Manual 1 - Page 2
    you have chosen Kenwood for your land mobile radio applications. Notices to the User ◆ Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified
  • Kenwood TK-2360 | User Manual 1 - Page 3
    battery pack. • Do not use options not specified by Kenwood. • If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts the battery pack. • Do not immerse the transceiver in water. • Always switch the transceiver power off before installing optional accessories. •
  • Kenwood TK-2360 | User Manual 1 - Page 4
    parts are exposed from the antenna covering. Transmitting at such a time may result in a high-frequency burn. • If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, remove the battery pack from the transceiver, and contact your Kenwood
  • Kenwood TK-2360 | User Manual 1 - Page 5
    is melted, the gas release vent or safety function is damaged, or the electrolyte is ignited, the battery may generate heat or smoke, rupture, or burst into flame. • Do not leave the battery near fires, stoves, or other heat generators (areas reaching over 80°C/ 176°F)! If the polymer separator is
  • Kenwood TK-2360 | User Manual 1 - Page 6
    generate heat or smoke, rupture, or burst into flame. • Use only the specified charger and observe charging requirements! If the battery is charged in unspecified conditions (under high temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodelled
  • Kenwood TK-2360 | User Manual 1 - Page 7
    water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems. • Do not charge the battery for longer than the specified time! If the battery pack has not finished charging even after the regulated time has passed, stop it. The
  • Kenwood TK-2360 | User Manual 1 - Page 8
    an authorized Kenwood service facility, or the factory. Carefully unpack the transceiver. If any items are missing or damaged, file a claim with the carrier immediately. Supplied Accessories Belt clip 1 Speaker/ microphone jacks cap 1 Speaker/ microphone locking bracket 1 Instruction manual 1 
  • Kenwood TK-2360 | User Manual 1 - Page 9
    the safety catch, press the release latch, then pull the battery pack away from the transceiver. 2 1 3 Note: ◆ For battery pack charging procedures and useage, refer to the battery charger Instruction Manual. ◆ Before charging a battery pack that is attached to the transceiver, ensure that the
  • Kenwood TK-2360 | User Manual 1 - Page 10
    setting on your transceiver). If you want to transmit a stronger signal (using the high power setting on your transceiver), use an optional rechargeable battery pack. 1 To open the battery case, press on the two tabs on the upper rear of the case, then pull the two halvs apart. 2 Insert 6 AA (LR6
  • Kenwood TK-2360 | User Manual 1 - Page 11
    Installing the Belt Clip Note: When first installing the belt clip, you must remove the battery pack from the rear of the transceiver. 1 Remove the 2 screws from the rear of the transceiver, then remove the small, plastic black covering that was
  • Kenwood TK-2360 | User Manual 1 - Page 12
    2 While holding the cap in place, push it towards the bottom of the transceiver until the tabs on the cap click into place. • To remove the cap, hold the top of the cap in place with your finger while inserting a 3 mm or smaller flat blade screwdriver under the bottom of the cap. Slowly slide the
  • Kenwood TK-2360 | User Manual 1 - Page 13
    a channel. ② Power switch/ Volume control Rotate to turn the transceiver ON/OFF and to adjust the volume. ③ Transmit/ Receive/ Battery low indicator If enabled by your dealer, lights red while transmitting, green while receiving a call, and orange or blue (depending on dealer programming) when
  • Kenwood TK-2360 | User Manual 1 - Page 14
    the DTMF number that has been programmed onto your selected channel. Your dealer may program different DTMF numbers on different channels. n Battery Indicator Press this key to announce the current battery energy level. Battery level 4 (green LED) means the battery is full, level 3 (orange LED) is
  • Kenwood TK-2360 | User Manual 1 - Page 15
    will change to the Emergency channel and begin transmitting based on your dealer settings. Note: This function can be programmed only on the Auxiliary key. this key to change the transmit power on the current channel to low power, to conserve battery energy. n Monitor Press this key to deactivate QT
  • Kenwood TK-2360 | User Manual 1 - Page 16
    this key. n Scrambler The Scrambler function allows you to hold a conversation in complete privacy. When activated, any other party listening in on your channel will be unable to understand your conversation. n Squelch Off Press this key to hear background noise. Press this key again to return to
  • Kenwood TK-2360 | User Manual 1 - Page 17
    . Adjusting the Volume Rotate the Power switch/ Volume control to adjust the volume. Clockwise increases the volume and counterclockwise decreases it. Selecting a Channel Select your desired channel using the Selector knob. Each channel is programmed with settings for transmitting and receiving. 10
  • Kenwood TK-2360 | User Manual 1 - Page 18
    the PTT switch to receive. • For best sound quality, hold the transceiver approximately 1.5 inches (3 ~ 4 cm) from your mouth. • If signaling has been programmed on the channel, you will hear a call only if the received signal matches your transceiver settings. SCAN Scan monitors for signals on the
  • Kenwood TK-2360 | User Manual 1 - Page 19
    by your dealer, you can set a new channel as the Priority channel by selecting your desired channel and pressing the key programmed as Priority Channel Select. Temporary Channel Lockout During scan, you can temporarily remove specific channels from the scanning sequence by pressing the key
  • Kenwood TK-2360 | User Manual 1 - Page 20
    Alphanumeric 2-way Paging Function, and is a protocol owned by Kenwood Corporation. Note: If set up by your dealer, your stations. ■ Transmitting 1 Select your desired FleetSync channel. • Your dealer can program different ID codes on different channels. 2 Press the PTT switch and begin your
  • Kenwood TK-2360 | User Manual 1 - Page 21
    Status Message You can transmit pre-programmed Status messages by pressing the keys programmed as Status 1 or Status 2. Status messages are 2-digit codes ranging from 10 to 99 (80 ~ 99 are reserved for special messages). VOICE OPERATED TRANSMISSION (VOX)
  • Kenwood TK-2360 | User Manual 1 - Page 22
    additional operation on your part. Time-out Timer (TOT) The Time-out Timer is used to prevent you from using a channel for an extended being received and no operations are being performed. Low Battery Warning Low Battery Warning alerts you when the battery needs to be recharged. Your dealer can set
  • Kenwood TK-2360 | User Manual 1 - Page 23
    is sent each time the PTT switch is pressed and/or released. Compander If programmed by your dealer for a channel, the compander will remove excessive noise from transmitted signals, to provide higher clarity of signals. Busy Channel Lockout (BCL) If BCL is set up by your dealer, you will be unable
  • Kenwood TK-2360 | User Manual 1 - Page 24
    Optional Signaling Your dealer may also program several types of optional signaling for your transceiver channels. 2-tone Signaling: 2-tone Signaling opens the squelch only when your transceiver receives )" on page 13. MDC-1200: MDC-1200 is a data system using Audio Frequency Shift Keying (AFSK). 17
  • Kenwood TK-2360 | User Manual 1 - Page 25
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
© B62-2209-00 (C)
09 08 07 06 05 04 03 02 01 00
INSTRUCTION MANUAL
VHF FM TRANSCEIVER
TK-2360
UHF FM TRANSCEIVER
TK-3360