Kenwood TK-3401D User Manual 3

Kenwood TK-3401D Manual

Get Kenwood TK-3401D PDF manuals and user guides View all Kenwood TK-3401D manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-3401D manual content summary:

  • Kenwood TK-3401D | User Manual 3 - Page 1
    TK-3401D UHF DIGITAL TRANSCEIVER USER MANUAL B5A-0037-30 (E, T)
  • Kenwood TK-3401D | User Manual 3 - Page 2
  • Kenwood TK-3401D | User Manual 3 - Page 3
    chosen KENWOOD for your dPMR446 applications. OPERATING CONDITIONS Open locations (no obstructions) : Up to 9.0 km Note: ◆ The above range is based as much as twenty percent over analog. NOTICES TO THE USER Refer service to qualified technicians only. Safety: It is important that the operator
  • Kenwood TK-3401D | User Manual 3 - Page 4
    specified by KENWOOD. • If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts. • If a headset or headphone at gasoline service stations. • Near explosives or blasting sites. • In aircraft. (Any use of the transceiver must follow the instructions and regulations
  • Kenwood TK-3401D | User Manual 3 - Page 5
    the antenna covering. Transmitting at such a time may result in a high-frequency burn. • If an abnormal odor or smoke is detected coming from the off immediately, remove the battery pack from the transceiver, and contact your KENWOOD dealer. • Use of the transceiver while you are driving may be
  • Kenwood TK-3401D | User Manual 3 - Page 6
    Information concerning the battery pack: The battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters. •
  • Kenwood TK-3401D | User Manual 3 - Page 7
    • Use only the specified charger and observe charging requirements! If the battery is charged in unspecified conditions (under high temperature over the regulated value, excessive high voltage or current over regulated value, or with a remodeled charger), it may overcharge or an abnormal chemical
  • Kenwood TK-3401D | User Manual 3 - Page 8
    your eyes with fresh water as soon as possible, without rubbing your eyes. Go to the hospital immediately. If left untreated, it may cause eye-problems. • Do not charge the battery for longer than the specified time! If the battery pack has not finished charging even after the regulated time
  • Kenwood TK-3401D | User Manual 3 - Page 9
    OPERATIONS 24 VOICE OPERATED TRANSMISSION (VOX 25 ALL RESET MODE 26 TROUBLESHOOTING GUIDE 27 UNPACKING AND CHECKING EQUIPMENT Carefully unpack the 1 • Belt clip (KBH-10 1 • Screw (M3 x 8 mm 2 • User guide 1 Note: ◆ Refer to "PREPARATION" {page 2} for accessory installation instructions. 1
  • Kenwood TK-3401D | User Manual 3 - Page 10
    PREPARATION INSTALLING/ REMOVING THE BATTERY PACK ◆ Do not short the battery terminals or dispose of the battery by fire. ◆ Never attempt to remove the casing from the battery pack. ◆ Install the battery pack after cleaning the battery pack contacts and the transceiver terminals. 1 Align the battery
  • Kenwood TK-3401D | User Manual 3 - Page 11
    until it reaches a normal temperature before charging it again. ◆ The ambient temperature should be between 5°C and 40°C while charging is in progress. Charging outside this range may not fully charge the battery. 3
  • Kenwood TK-3401D | User Manual 3 - Page 12
    ◆ The battery pack life is over when its operating time decreases even though it is fully and correctly charged. Replace the battery pack. ◆ While operating the transceiver using a Li-ion battery pack in areas of an ambient temperature of -10°C and lower, operating time may be shortened. BATTERY
  • Kenwood TK-3401D | User Manual 3 - Page 13
    THE CAP OVER THE SPEAKER/ MICROPHONE JACKS Install the cap over the speaker/ microphone jacks when not using an optional speaker/ microphone or headset. Note: ◆ To keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied cap. 1 Place the cap over the
  • Kenwood TK-3401D | User Manual 3 - Page 14
    ) plugs into the speaker/ microphone jacks of the transceiver. 2 Place the locking bracket over the speaker/ microphone (or headset) plugs so that the locking tabs insert into the transceiver grooves. • Push down on the locking bracket to slide it into place. 3 While holding the
  • Kenwood TK-3401D | User Manual 3 - Page 15
    SWITCHING THE AUDIO OUTPUT It is necessary to switch the audio output if you listen only through the earphone (2.5). 1 Switch the transceiver power OFF. 2 Press and hold the PTT switch and Side 2 key while turning the transceiver power ON. 3 Continue to hold the PTT switch and Side 2 key until a
  • Kenwood TK-3401D | User Manual 3 - Page 16
    ORIENTATION Microphone Antenna Speaker Battery pack Selector Rotate to change the operating channel. • To change the operating frequency, Common ID or QT/DQT settings of a channel, refer to "CHANNEL SETUP MODE" {page 11}. • Channel Annunciation: When changing channels, the transceiver will
  • Kenwood TK-3401D | User Manual 3 - Page 17
    how to change the function of the Side 2 key, refer to "KEY ASSIGNMENT MODE" {page 20}. Speaker/ microphone jacks Insert the Speaker/ microphone or Headset plug into this jack. LED Indicator Status Indicator Color Flashes blue Flashes orange Lights red Lights green Blinks red Blinks green Meaning
  • Kenwood TK-3401D | User Manual 3 - Page 18
    BASIC OPERATIONS 1 Turn the Power switch/ Volume control clockwise to switch the transceiver power ON. • A beep will sounds. 2 Press the key programmed with the [Monitor] or [Squelch Off] (Side 2 key default) function to hear background noise, then rotate the Power switch/ Volume control to adjust
  • Kenwood TK-3401D | User Manual 3 - Page 19
    and Common ID (Digital)/ QT/DQT (Analog) settings. The table below lists the default channel settings. Zone type Digital Channel Number Frequency Common ID 1 446.103125 MHz 1 2 446.109375 MHz 2 3 446.115625 MHz 3 4 446.121875 MHz 4 5 446.128125 MHz 5 6 446.134375 MHz 6 7 446
  • Kenwood TK-3401D | User Manual 3 - Page 20
    Zone type Channel Number Frequency Analog QT/DQT 1 446.00625 MHz 94.8 Hz 2 446.09375 MHz 88.5 Hz 3 446 16 446.08125 MHz D243N Note: ◆ You must first select an operating frequency for a channel before you can select a Common ID (Digital)/ QT/DQT (Analog) setting for that same channel.
  • Kenwood TK-3401D | User Manual 3 - Page 21
    the PTT switch to save the setting. • A beep will sound if there is no change in the zone type. The transceiver will move to the Frequency Setting and announces "Channel". • If the zone type is changed, the transceiver announces "Confirm". 7 Press the PTT switch and Side 1 key. • All channel
  • Kenwood TK-3401D | User Manual 3 - Page 22
    number. 4 Press the Side 1 or Side 2 key to increment/ decrement the Table number, to select the new channel frequency. • Table numbers and their corresponding operating frequencies are provided in the table {page 15}. • A voice announcement will inform you of the currently selected Table number
  • Kenwood TK-3401D | User Manual 3 - Page 23
    16 446.196875 MHz 32 Table Number 1 2 3 4 5 6 7 8 Analog Operating Frequency Table Number 446.00625 MHz 9 446.01875 MHz 10 446.03125 MHz 11 446.04375 MHz .06875 MHz 14 446.08125 MHz 15 446.09375 MHz 16 Operating Frequency 446.003125 MHz 446.009375 MHz 446.015625 MHz 446.021875 MHz
  • Kenwood TK-3401D | User Manual 3 - Page 24
    COMMON ID SETTINGS (DIGITAL) To change the Common ID settings of a channel of Digital: 1 Follow the operating steps in Zone Selection to select the zone type (digital). 2 Rotate the Selector to your desired channel. • The transceiver announces Channel number. 3 Press the Side 1 or Side 2 key to
  • Kenwood TK-3401D | User Manual 3 - Page 25
    QT/ DQT SETTINGS (ANALOG) Quiet Talk (QT) and Digital Quiet Talk (DQT) are functions that reject undesired signals on your channel. You will hear a call only when you receive a signal that contains a matching QT tone or DQT code. If a call containing a different tone or code is received, squelch
  • Kenwood TK-3401D | User Manual 3 - Page 26
    6 Press the PTT switch to save the setting. • A beep will sound. • Repeat steps 2 to 6 to set up another channel. 7 Turn the transceiver power OFF and then ON again to activate the new settings. Note: ◆ The transceiver will automatically return to normal operation if no action is performed for 5
  • Kenwood TK-3401D | User Manual 3 - Page 27
    CHANNEL CONFIRMATION MODE To confirm your channel settings: 1 With the transceiver power OFF, press and hold the PTT switch while turning the transceiver power ON. • Continue to hold the PTT switch until the LED lights orange and the transceiver announces "Confirm". 2 Release the PTT switch. • The
  • Kenwood TK-3401D | User Manual 3 - Page 28
    KEY ASSIGNMENT MODE This transceiver allows you to reprogram the Side 1 and Side 2 keys with any of the functions listed in the table below. Explanations on the use of each function are provided under "PROGRAMMABLE FUNCTIONS" {page 22}. Table Number Function Name 0 None (no function) Digital ✓
  • Kenwood TK-3401D | User Manual 3 - Page 29
    2 Release the key. • If you continue to hold both keys, or if you release both keys, the operation will cancel in 5 seconds. 3 Press and hold the key to be reprogrammed (either the Side 1 or Side 2 key). • The transceiver will announce "Table zero". 4 Release the key. 5 Press the Side 1 or Side 2
  • Kenwood TK-3401D | User Manual 3 - Page 30
    PROGRAMMABLE FUNCTIONS ■ Calling Alert Calling alert tones help identify yourself to party members and inform them that you are calling. Your dealer can set up your transceiver with 1 of 10 calling alert tones. If each party member uses a different tone, it is easy to know who is calling. To make a
  • Kenwood TK-3401D | User Manual 3 - Page 31
    ■ Scan Press this key to start scanning the transceiver channels. Priority Scan: The Priority channel is a channel that is given first priority to while scanning. The Priority channel is set by your dealer. Revert Channel: During Scan, pressing the PTT switch will automatically select the transceiver
  • Kenwood TK-3401D | User Manual 3 - Page 32
    BACKGROUND OPERATIONS TIME-OUT TIMER (TOT) The Time-out Timer prevent callers from using a channel for an extended duration. If you continuously transmit for the duration programmed by your dealer (default is 60 seconds), transmission will stop and an alert tone will sound. To stop the tone, release
  • Kenwood TK-3401D | User Manual 3 - Page 33
    hands-free. VOX can only be used if you are using a supported headset. To activate VOX and set the VOX Gain level, perform the following steps: 1 Connect the headset to the transceiver . • The VOX function does not activate when a headset is not connected to the accessory terminal of the transceiver
  • Kenwood TK-3401D | User Manual 3 - Page 34
    settings to their default values. This function will reset all channels to their default frequencies and Common ID (Digital)/ QT/DQT (Analog), the VOX function to its default status, and all keys to their default functions. To reset the transceiver: 1 With the transceiver power OFF, press
  • Kenwood TK-3401D | User Manual 3 - Page 35
    TROUBLESHOOTING GUIDE Problem sure you are using the same frequency and Common ID (Digital)/ QT/ Make sure you are within range of the other transceivers. problem persists, contact a KENWOOD authorized service center for repairs. You may return your transceiver for service to the authorized KENWOOD
  • Kenwood TK-3401D | User Manual 3 - Page 36
    © 2017
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
UHF DIGITAL TRANSCEIVER
USER MANUAL
TK-3401D
B5A-0037-30 (E, T)