Kenwood TK-3701D User Manual 2

Kenwood TK-3701D Manual

Get Kenwood TK-3701D PDF manuals and user guides View all Kenwood TK-3701D manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-3701D manual content summary:

  • Kenwood TK-3701D | User Manual 2 - Page 1
    TK-3701D USER MANUAL B5A-3234-00/01_EN
  • Kenwood TK-3701D | User Manual 2 - Page 2
    27 TIME-OUT TIMER (TOT 27 BATTERY SAVER...27 LOW BATTERY WARNING 27 BUSY CHANNEL LOCKOUT (BCL 27 VOICE ANNOUNCEMENT 27 ALL RESET MODE 28 TROUBLESHOOTING GUIDE 29 SPECIFICATIONS 30 2
  • Kenwood TK-3701D | User Manual 2 - Page 3
    PREPARATION INSTALLING/ REMOVING THE BATTERY PACK The battery pack is not charged at the factory; charge it before use. CAUTION ◆ Do not short the battery terminals or dispose of the battery by fire. ◆ Never attempt to remove the casing from the battery pack. 1 Align the battery pack with the back
  • Kenwood TK-3701D | User Manual 2 - Page 4
    CHARGING THE BATTERY PACK ATTENTION: ◆ Always switch OFF a transceiver equipped with a battery pack before inserting the transceiver into the charger. 1 Plug the AC adapter cable into the jack located on the rear of the charger. 2 Plug the AC adapter into an AC outlet. 3 Slide a battery pack or a
  • Kenwood TK-3701D | User Manual 2 - Page 5
    INSTALLING THE BELT CLIP If necessary, attach the belt clip using the two supplied M3 x 8 mm binding screws. Note: ◆ If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting in a hot environment. ◆ Use the Phillips #2 screwdriver. Belt
  • Kenwood TK-3701D | User Manual 2 - Page 6
    INSTALLING THE SPEAKER/ MICROPHONE OR HEADSET Note: ◆ The transceiver is not fully water resistant when using a speaker/ microphone or headset. ◆ Use the Phillips #1 screwdriver. 1 Insert the speaker/ microphone plugs into the speaker/ microphone jacks of the transceiver. 2 Place the locking bracket
  • Kenwood TK-3701D | User Manual 2 - Page 7
    ORIENTATION Antenna d e f Battery pack Speaker Microphone ab c a Selector Rotate to change the operating channel. b LED indicator Refer to the "LED Indicator Status" {p. 9}. c Power switch/ Volume control Turn clockwise to switch the transceiver ON. To switch the transceiver OFF, turn
  • Kenwood TK-3701D | User Manual 2 - Page 8
    BASIC OPERATION POWER ON Turn the Power switch/ Volume control clockwise to switch the transceiver power ON. • A beep will sounds. ADJUST THE VOLUME Rotate the Power switch/ Volume control to adjust the volume. • Clockwise increases the volume and counterclockwise decreases the volume. Note: ◆ To
  • Kenwood TK-3701D | User Manual 2 - Page 9
    RECEIVE VOICE The LED lights in green. When the other party transmits it, you hear the voice of the other party. POWER OFF After use, turn off the power. To switch the transceiver power OFF, turn the Power switch/ Volume control fully counterclockwise, until a click sounds. LED Indicator Status
  • Kenwood TK-3701D | User Manual 2 - Page 10
    SELF-PROGRAMMING MODE This transceiver allows you to reprogram each of the channels with different frequencies and QT/DQT (Analogue)/ Common ID (Digital) settings. The table below lists the default channel settings. Zone 1 (Analogue) Channel Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Frequency
  • Kenwood TK-3701D | User Manual 2 - Page 11
    Zone 3 (Digital) Channel Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Frequency (MHz) 446.003125 446.009375 446.015625 446.021875 446.028125 446.034375 446.040625 446.046875 446.053125 446.059375 446.065625 446.071875 446.078125 446.084375 446.090625 446.096875 Common ID 1 2 3 4 5 6 7 8 9 10 11
  • Kenwood TK-3701D | User Manual 2 - Page 12
    SELF-PROGRAMMING FLOW The flow of Self-programming is as follows. [PTT] + [Side 1] + Power On Release [PTT] + [Side 1] Select the Zone Number [Side 1] / [Side 2] [PTT] Setup Mode Selection [Side 1] / [Side 2] : Change between setup modes. [PTT] : Enter to selected setup mode. [Selector] :
  • Kenwood TK-3701D | User Manual 2 - Page 13
    ZONE SELECTION 1 With the transceiver power OFF, press and hold the PTT switch and Side 1 button while turning the transceiver power ON. • Continue to hold the PTT switch and Side 1 button until the LED lights yellow and the transceiver announces "Self". 2 Release the PTT switch and Side 1 button. •
  • Kenwood TK-3701D | User Manual 2 - Page 14
    FREQUENCY SETUP 1 During Setup Mode Selection, rotate the Selector to select a channel number. • The transceiver announces the zone number and channel number. 2 Press the Side 1 or Side 2 button to select the Frequency Setup Mode. • The transceiver announces "Channel". 3 Press the PTT switch to
  • Kenwood TK-3701D | User Manual 2 - Page 15
    Frequency Table Table Number D01 D02 D03 D04 D05 D06 D07 D08 D09 D10 D11 D12 D13 D14 D15 D16 Digital Frequency (MHz) Table Number 446.103125 D17 446.109375 D18 446.115625 D19 446.121875 D20 446.128125 D21 446.134375 D22 446.140625 D23 446.146875 D24 446.153125 D25 446.159375
  • Kenwood TK-3701D | User Manual 2 - Page 16
    QT/DQT SETUP (ANALOGUE) Quiet Talk (QT) and Digital Quiet Talk (DQT) are functions that reject undesired signals on your channel. You will hear a call only when you receive a signal that contains a matching QT tone or DQT code. If a call containing a different tone or code is received, squelch will
  • Kenwood TK-3701D | User Manual 2 - Page 17
    QT/DQT Table Table Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 QT frequency DQT Code 67.0 Hz 71.9 Hz 74.4 Hz 77.0 Hz 79.7 Hz 82.5 Hz 85.4 Hz 88.5 Hz 91.5 Hz 94.8 Hz 97.4 Hz 100.0 Hz 103.5 Hz 107.2 Hz 110.9 Hz 114.8 Hz 118.8 Hz 123.0 Hz 127.3 Hz 131.8 Hz Table Number 21 22 23 24 25 26
  • Kenwood TK-3701D | User Manual 2 - Page 18
    COMMON ID SETUP (DIGITAL) Common ID is a signaling system designed for Digital communications. When a channel is setup with an ID, squelch will only open when a call containing a matching Common ID is received. If a call containing a different Common ID is made on the same channel you are using, you
  • Kenwood TK-3701D | User Manual 2 - Page 19
    CHANNEL CONFIRMATION MODE To confirm your channel settings: 1 With the transceiver power OFF, press and hold the PTT switch while turning the transceiver power ON. • Continue to hold the PTT switch until the LED lights yellow and the transceiver announces "Confirm". 2 Release the PTT switch. • The
  • Kenwood TK-3701D | User Manual 2 - Page 20
    BUTTON FUNCTION PROGRAMMING MODE This transceiver allows you to reprogram the Side 1 and Side 2 buttons with any of the functions listed in the table below. Explanations on the use of each function are provided under "PROGRAMMABLE FUNCTIONS" {p. 22}. Functions List Table Number Press Press and
  • Kenwood TK-3701D | User Manual 2 - Page 21
    To change the functions of the Side 1 and Side 2 buttons: 1 With the transceiver power OFF, press and hold the Side 1 and Side 2 buttons while turning the transceiver power ON. • Continue to hold the Side 1 and Side 2 buttons until the LED lights yellow and the transceiver announces "Setup". 2
  • Kenwood TK-3701D | User Manual 2 - Page 22
    when Button Lock is active: Button Lock, Monitor, Monitor Momentary, Squelch Off, and Squelch Off Momentary. Note: ◆ * To lock the Selector is supported from firmware version 1.20 / serial number C0910941 or later. Monitor In Digital mode, press this button to deactivate Common ID signaling. Press
  • Kenwood TK-3701D | User Manual 2 - Page 23
    Scan Press this button to start scanning the transceiver channels. Second Channel Scan: This scan type to start the Second Channel Scan on the current zone. The Second Channel Scan is set by your dealer. Priority Scan: The Priority channel is a channel that is given first priority to while scanning.
  • Kenwood TK-3701D | User Manual 2 - Page 24
    VOICE OPERATED TRANSMISSION (VOX) VOX (VOX/ Semi-VOX) operation allows you to transmit hands-free. VOX can only be used if you are using a supported headset. VOX Type VOX: When the voice level to the microphone is higher than the reference level (VOX Gain Level), the transceiver automatically starts
  • Kenwood TK-3701D | User Manual 2 - Page 25
    Note: ◆ If a headset is connected to the transceiver while the VOX function is switched ON and the VOX Gain level is configured to a higher, more sensitive level, louder received signals may cause the transceiver to start transmission. ◆ If no action is performed for 20 seconds, the transceiver will
  • Kenwood TK-3701D | User Manual 2 - Page 26
    SECOND PTT FUNCTION Apart from the channel you normally select, you can use another channel (Second PTT channel) with a dedicated [Second PTT]. • The Second PTT function can be activated by your dealer. Operation 1 Press the button programmed as [Second PTT] to move to the second PTT channel. 2
  • Kenwood TK-3701D | User Manual 2 - Page 27
    BACKGROUND OPERATIONS TIME-OUT TIMER (TOT) The Time-out Timer prevent callers from using a channel for an extended duration. If you continuously transmit for the duration programmed by your dealer (default is 60 seconds), transmission will stop and an alert tone will sound. To stop the tone, release
  • Kenwood TK-3701D | User Manual 2 - Page 28
    ALL RESET MODE At some point in time, you may desire to reset the transceiver settings to their default values. This function will reset all channels to their default frequencies and Common ID (Digital)/ QT/DQT (Analogue), the VOX function to its default status, and all buttons to their default
  • Kenwood TK-3701D | User Manual 2 - Page 29
    TROUBLESHOOTING GUIDE Problem Solution Cannot turn the transceiver power ON. • The battery pack may be dead. Recharge or replace the battery pack. • The battery pack may not be
  • Kenwood TK-3701D | User Manual 2 - Page 30
    SPECIFICATIONS RF Output Power 0.5 W e.r.p. Audio Output Power 1 W (internal speaker) / 500 mW (external output) Frequency Stability ± 0.5 ppm Operating Voltage Operating Temperature Range Dimensions (W x H x D) (Projections not included with KNB-45L) 7.5 V DC ±20 % -30°C - +60°C 54 × 123 ×
  • Kenwood TK-3701D | User Manual 2 - Page 31
    © 2020
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
USER MANUAL
TK-3701D
B5A-3234-00/01_EN