Kenwood TK-5720 User Manual

Kenwood TK-5720 Manual

Get Kenwood TK-5720 PDF manuals and user guides View all Kenwood TK-5720 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-5720 manual content summary:

  • Kenwood TK-5720 | User Manual - Page 1
    TK-5720/ TK-5820 VHF P25 Transceiver/ UHF P25 Transceiver Instruction Manual ÉMETTEUR-RÉCEPTEUR P25 VHF/ ÉMETTEUR-RÉCEPTEUR P25 UHF MODE D'EMPLOI TRANSCEPTOR P25 VHF/ TRANSCEPTOR P25 UHF MANUAL DE INSTRUCCIONES © B62‑2206‑00 (K) 09 08 07 06 05 04 03 02 01 00
  • Kenwood TK-5720 | User Manual - Page 2
    ENGLISH VHF P25 TRANSCEIVER/ UHF P25 TRANSCEIVER TK-5720/ TK-5820 Instruction Manual Terminal Description Microphone Jack Pin NO. Pin Name 1 BLC 2 SB 3 GND 4 PTT/TXD 5 ME 6 MIC 7 HOOK/RXD 8 DM Description Mic key backlight control Power Output
  • Kenwood TK-5720 | User Manual - Page 3
    are grateful you have chosen Kenwood for your personal mobile applications. This instruction manual covers only the basic operations etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if
  • Kenwood TK-5720 | User Manual - Page 4
    interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this polarity and voltage of the vehicle before installing the transceiver. ◆ Use only a Kenwood optional DC power cable. ◆ Do not cut and/or remove the fuse holder on
  • Kenwood TK-5720 | User Manual - Page 5
    Background Operations 20 Time-out Timer (TOT 20 Signal Strength Indicator 20 Compander...20 Busy Channel Lockout (BCL 20 PTT ID...20 VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT 21 Voice Recorder 21 Voice
  • Kenwood TK-5720 | User Manual - Page 6
    AND CHECKING EQUIPMENT Note: The following unpacking instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. Carefully unpack 5 x 16 mm self-tapping screw 4 • Hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Instruction manual 1 
  • Kenwood TK-5720 | User Manual - Page 7
    his/her aid in determining if they will perform normally while transmitting. Note: The following preparation instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. Tools Required Note: Before installing the transceiver, always check how far the
  • Kenwood TK-5720 | User Manual - Page 8
    Installing the Transceiver For passenger safety, install the transceiver securely using an optional mounting bracket and screw set so the transceiver will not break loose in the event of a collision. 1 Mark the position of the holes in the dash by using the mounting bracket as a template. Drill the
  • Kenwood TK-5720 | User Manual - Page 9
    Front Panel : @. GETTING ACQUAINTED ;=   B> 2 8     ① (power) switch Press and hold for approximately 1 second to switch the transceiver power ON and OFF. ② key Press to activate its programmable function {page 6}. ③ key Press to activate its programmable function {page 6}. ④ key
  • Kenwood TK-5720 | User Manual - Page 10
    ⑫ key Press to activate its programmable function {page 6}. ⑬ key Press to activate its programmable function {page 6}. ⑭ Speaker Internal speaker ⑮ PTT (Push-to-Talk) switch Press and hold this switch then, speak into the microphone to call a station. Display Indicator Description Monitor or
  • Kenwood TK-5720 | User Manual - Page 11
    board has been installed. 3 Can be programmed only on the foot switch. key and an optional auxiliary switch, such as an emergency 4 Available only for P25 operation. 5 Available only if the Secure Cryptographic Module (SCM) optional board has been installed. 
  • Kenwood TK-5720 | User Manual - Page 12
    BASIC OPERATIONS Switching Power ON/OFF Press and hold for approximately 1 second to turn the transceiver power ON. Press and hold again to turn the transceiver OFF. ■ Transceiver Password If the transceiver is password protected, "PASSWORD" will appear on the display when the power is turned ON.
  • Kenwood TK-5720 | User Manual - Page 13
    matches the ID set up on your transceiver, and the Network Access Code also matches, you can hear the caller's voice. ■ Receiving Individual Calls (P25) When you receive an individual call, a ringing tone will sound. If the Network Access Code matches and the squelch type is set to Selective call
  • Kenwood TK-5720 | User Manual - Page 14
    MENU MODE Many functions on this transceiver are selected or configured through the Menu instead of physical controls. Once you become familiar with the Menu system, you will appreciate the versatility it offers. Menu Access 1 Press the key programmed as Menu. • The category list is shown. • When
  • Kenwood TK-5720 | User Manual - Page 15
    Display DIRECT CH1 SEL ~ DIRECT CH5 SEL DISP FORMAT ENCRYPTION ENCRYP CODE FIXED VOLUME GPS POS DISP HOME CH SEL HORN ALERT INDIVIDUAL KEY DELETE LCD BRIGHTNESS MONITOR OST OST LIST PLAYBACK PRI CH SEL PUBLIC ADDRESS SCAN SCAN DEL/ADD SELCALL SELCALL+STATUS SELCALL+SDM SEND GPS DATA SHORT MESSAGE
  • Kenwood TK-5720 | User Manual - Page 16
    Display ZEROIZE ZONE DEL/ADD Zeroize Zone Delete/Add Description Character Entry There are 2 methods available for entering characters: 1) / keys Press / to cycle through the chracters A ~ Z, 0 ~ 9 and a space (default settings). You can also assign a character to an optional key and later press
  • Kenwood TK-5720 | User Manual - Page 17
    SCAN Scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a signal is present. To begin scanning, press the key programmed as Scan. • The icon appears on the display. • When a signal is detected on a channel,
  • Kenwood TK-5720 | User Manual - Page 18
    Priority-Channel Select If the Priority channel has been set as Operator Selectable by your dealer, you can reprogram the Priority channels. 1 Select your desired zone and channel. 2 Press the key programmed as Priority-channel Select. 3 Press / to select "NORMAL", "PRIORITY 1" ( ), "PRIORITY 2" (
  • Kenwood TK-5720 | User Manual - Page 19
    an Alphanumeric 2-way Paging Function, and is a protocol owned by Kenwood Corporation. Note: This function is available only in analog operation. mode. 3 Press / to select the station you want to call. • If Manual Dialing is enabled, you can directly enter the station ID using the microphone keypad
  • Kenwood TK-5720 | User Manual - Page 20
    can enter a station ID by using the microphone keypad. 4 Press to enter Status mode. 5 Press / to select the status you want to transmit. • If Manual Dialing is enabled, you can enter a status ID by using the microphone keypad. 6 Press the microphone PTT switch or to initiate the call. • "
  • Kenwood TK-5720 | User Manual - Page 21
    ADVANCED OPERATIONS DTMF (Dual Tone Multi Frequency) Calls ■ Making a DTMF Call Note: DTMF calls can be made only in analog operation. Manual Dialing (Microphone Keypad Only) 1 Press and hold the microphone PTT switch. 2 Enter the desired digits using the microphone keypad. • If you release the
  • Kenwood TK-5720 | User Manual - Page 22
    turn the OST function OFF. ■ Network Access Code (NAC) Your dealer may have programmed a Network Access Code on your transceiver channels. NAC is a feature of P25 transceivers that functions similar to QT/DQT; squelch will open when the correct NAC is received. 17
  • Kenwood TK-5720 | User Manual - Page 23
    ■ Optional Signaling Your dealer may also program several types of optional signaling for your transceiver channels. 2-tone Signaling: 2-tone Signaling opens the squelch only when your transceiver receives a call containing matching 2 tones. DTMF Signaling: DTMF Signaling opens the squelch only when
  • Kenwood TK-5720 | User Manual - Page 24
    Clock If activated by your dealer, you can view the clock by pressing the key programmed as Clock. Note: Removing the transceiver power for extended periods will cause the clock time to clear. ■ Clock Adjustment To set the time: 1 Press the key programmed as Clock Adjustment. • The current time
  • Kenwood TK-5720 | User Manual - Page 25
    BACKGROUND OPERATIONS Your dealer can activate a variety of transceiver functions to perform without any additional operation on your part. Time-out Timer (TOT) The Time-out Timer is used to prevent you from using a channel for an extended duration. If you continuously transmit for a preset time,
  • Kenwood TK-5720 | User Manual - Page 26
    VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT Voice Recorder The voice recorder allows you to record conversations and create voice memos. n Auto Recording If activated, the auto recorder will continuously
  • Kenwood TK-5720 | User Manual - Page 27
    end the recording at any time by pressing . • To delete the selected recording, press . To clear all the recorded data, press and hold . Voice Guide When changing the zone and/or channel, an audio voice will announce the new zone and channel. Additionally, when changing a function setting, the new
  • Kenwood TK-5720 | User Manual - Page 28
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
TK-5720/ TK-5820
© B62-2206-00 (K)
09 08 07 06 05 04 03 02 01 00
VHF P25 TRANSCEIVER/
UHF P25 TRANSCEIVER
INSTRUCTION MANUAL
ÉMETTEUR-RÉCEPTEUR P25 VHF/
ÉMETTEUR-RÉCEPTEUR P25 UHF
MODE D’EMPLOI
TRANSCEPTOR P25 VHF/
TRANSCEPTOR P25 UHF
MANUAL DE INSTRUCCIONES