Home » Kenwood Manuals » Electronics Accessories » Kenwood TK-7302 » Manual Viewer

Kenwood TK-7302 User Manual 2

Kenwood TK-7302 Manual

Get Kenwood TK-7302 PDF manuals and user guides

View all Kenwood TK-7302 manuals

Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-7302 manual content summary:

Kenwood TK-7302 | User Manual 2 - Page 1
TK-7302/ TK-8302 TK-7302H/ TK-8302H TK-7302HV/ TK-8302HU VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D'EMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES © B62‑2167‑10 (K,K2) 09 08 07 06 05 04 03 02 01
Kenwood TK-7302 | User Manual 2 - Page 2
Kenwood TK-7302 | User Manual 2 - Page 3
ENGLISH VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7302/ TK-8302 TK-7302H/ TK-8302H TK-7302HV/ TK-8302HU INSTRUCTION MANUAL Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for Kenwood Corporation.
Kenwood TK-7302 | User Manual 2 - Page 4
Terminal Description ACC (D-SUB 15 Pin Connector) Pin NO. Pin Name 1 SB Description DC Power Output 2 IGN Ignition signal Input 3 PA 4 DO 5 DI 6 FNC1 7 FNC2 8 FNC3 9 FNC4 10 FNC5 11 FNC6 12 5C 13 HR1 14 HR2 15 GND Loudspeaker Output Audio Output Audio Input
Kenwood TK-7302 | User Manual 2 - Page 5
are grateful you have chosen Kenwood for your personal mobile applications. This instruction manual covers only the basic operations etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if
Kenwood TK-7302 | User Manual 2 - Page 6
of the vehicle before installing the transceiver. ◆ Use only the supplied DC power cable or a Kenwood optional DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable. For passenger safety, install the transceiver securely using the supplied mounting bracket and screw
Kenwood TK-7302 | User Manual 2 - Page 7
STARTED Note: The following instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. cable) • KMC-30 (TK-7302H/ TK-8302H 1 • KMC-35 (TK-7302/ TK-7302HV/ TK-8302/ TK-8302HU 1 Microphone hanger (with 4 x 16 mm self-tapping screws 1 Instruction manual
Kenwood TK-7302 | User Manual 2 - Page 8
and secure it with a retaining band. • Be sure to leave enough slack in the cables so the transceiver can be removed for servicing while keeping the power applied. n Installing the Transceiver For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set
Kenwood TK-7302 | User Manual 2 - Page 9
jack Insert the microphone plug into this jack. ⑦ Status Indicator Lights during a specified mode, based on dealer programming. ⑧ S / A / / keys Press to activate their programmable functions {page 4}. to this jack. ⑭ Power input connector Connect the DC Power Cable to this connector.
Kenwood TK-7302 | User Manual 2 - Page 10
display shows the channel number and the 2 dots show various modes of operation. The left and right dots on the display can be programmed to indicate specific modes of operation, as listed below. • AUX • Scan Delete/Add • Horn Alert • Scrambler • Lone Worker • Talk Around • Priority Channel
Kenwood TK-7302 | User Manual 2 - Page 11
the Volume Press the Volume Up key to increase the volume. Press the Volume Down key to decrease the volume. If Squelch Off has been programmed onto a key, you can use that function to listen to background noise while adjusting the volume level. Selecting a Zone and Channel Select the desired zone
Kenwood TK-7302 | User Manual 2 - Page 12
the scanning sequence. Priority Scan If a Priority channel has been programmed, the transceiver will automatically change to the Priority channel when a list. 1 Select your desired zone and/or channel. 2 Press the key programmed as Scan Delete/Add to remove a channel or press and hold the key for
Kenwood TK-7302 | User Manual 2 - Page 13
DTMF calls, you must use an optional microphone with a DTMF keypad. Manual Dialing 1 Press and hold the PTT switch. 2 Enter the desired (1 ~ 9). 3 Press the PTT switch to make the call. Redialing 1 Press the key programmed as Autodial or the microphone key. • "Ad" appears on the display. 2 Press the
Kenwood TK-7302 | User Manual 2 - Page 14
a revive code. • "St" appears on the display while the transceiver is stunned. SIGNALING Quiet Talk (QT)/ Digital Quiet Talk (DQT) Your dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/code which allows you to ignore (not hear
Kenwood TK-7302 | User Manual 2 - Page 15
Alphanumeric 2-way Paging Function and is a protocol owned by Kenwood Corporation. Note: If set up by your dealer, your ID, to request a call. Status Message You can transmit pre-programmed status messages by pressing the keys programmed as Status 1 and Status 2. Status messages are 2-digit codes
Kenwood TK-7302 | User Manual 2 - Page 16
the display while Lone Worker is activated. Talk Around During interruptions in service (such as a power failure), you can continue to communicate by using away or there are no geographical obstacles in the way. Press the key programmed as Talk Around to toggle the Talk Around function ON or OFF. •
Kenwood TK-7302 | User Manual 2 - Page 17
their transceivers. The scrambler function will not work with transceivers set up with different scrambler codes. Monitor/ Squelch Off You can use the key programmed as Monitor or Squelch Off to listen to weak signals that you cannot hear during normal operation and to adjust the volume when no
Kenwood TK-7302 | User Manual 2 - Page 18
. PTT ID PTT ID is the transceiver unique ID code which is sent each time the PTT switch is pressed and/or released. Compander If programmed by your dealer for a channel, the compander will remove excessive noise from transmitted signals, to provide higher clarity of signals. Voice Announcement When
Kenwood TK-7302 | User Manual 2 - Page 19
Kenwood TK-7302 | User Manual 2 - Page 20