Kenwood TK-7302H Operation Manual
Kenwood TK-7302H Manual
 |
View all Kenwood TK-7302H manuals
Add to My Manuals
Save this manual to your list of manuals |
Kenwood TK-7302H manual content summary:
- Kenwood TK-7302H | Operation Manual - Page 1
INSTRUCTION MANUAL VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7302/ TK-8302 TK-7302H/ TK-8302H © B62-2150-30 (M, M2, M4) 09 08 07 06 05 04 03 - Kenwood TK-7302H | Operation Manual - Page 2
- Kenwood TK-7302H | Operation Manual - Page 3
are grateful you have chosen Kenwood for your personal mobile applications. This instruction manual covers only the basic operations etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if - Kenwood TK-7302H | Operation Manual - Page 4
ground systems only! Check the battery polarity and voltage of the vehicle before installing the transceiver. ◆ Use only the supplied DC power cable or a Kenwood optional DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable. For passenger safety, install the transceiver - Kenwood TK-7302H | Operation Manual - Page 5
instructions are for use by your Kenwood dealer, an authorized Kenwood service facility TK-7302/ TK-8302 2 • 15 A fuse (TK-7302H/ TK-8302H 2 Mounting Bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • Hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Instruction manual - Kenwood TK-7302H | Operation Manual - Page 6
■ Installing the Transceiver For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will not break loose in the event of a collision. Note: Before installing the transceiver, check how far the mounting screws will extend below the - Kenwood TK-7302H | Operation Manual - Page 7
GETTING ACQUAINTED FRONT/REAR PANEL :@ . ; ACC. = B> 2 8 ᶃ (Power) switch Press to switch the transceiver ON or OFF. ᶄ / keys Press to activate their programmable functions {page 4}. ᶅ Display Refer to page 4. ᶆ / keys Press to activate their programmable functions {page 4}. - Kenwood TK-7302H | Operation Manual - Page 8
DISPLAY The display shows the channel number and the 2 dots show various modes of operation. The left and right dots on the display can be programmed to indicate specific modes of operation, as listed below. • AUX • Scan Delete/Add • Horn Alert • Scrambler • Lone Worker • Talk Around • - Kenwood TK-7302H | Operation Manual - Page 9
BASIC OPERATIONS SWITCHING POWER ON/ OFF Press to switch the transceiver ON. • A beep sounds and the display illuminates. • If the Transceiver Password function is programmed, "PS" will appear on the display when the power is turned ON. Refer to "Transceiver Password", below. Press again to switch - Kenwood TK-7302H | Operation Manual - Page 10
SCAN Scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a matching signal is present. To start/stop scanning, press the key programmed as Scan On/Off. • "Sc" appears on the display during Scan. • When a signal - Kenwood TK-7302H | Operation Manual - Page 11
channel selected before scan, whichever operation occured latest. DTMF CALLS Note: To make DTMF calls, you must use an optional microphone with a DTMF keypad. MANUAL DIALING 1 Press and hold the PTT switch. 2 Enter the desired digits using the keypad. • If Keypad Auto-PTT is enabled by your dealer - Kenwood TK-7302H | Operation Manual - Page 12
STUN This function is used when a transceiver is stolen or lost. When the transceiver receives a call containing a stun code, the transceiver becomes disabled. The stun code is cancelled when the transceiver receives a call with a revive code. • "St" appears on the display while the transceiver is - Kenwood TK-7302H | Operation Manual - Page 13
FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION FleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned by JVC KENWOOD Corporation. Note: If set up by your dealer, your transceiver may use the MDC-1200 feature in place of FleetSync. MDC-1200 and FleetSync cannot - Kenwood TK-7302H | Operation Manual - Page 14
toggle the Lone Worker function ON or OFF. • "Ln" appears on the display while Lone Worker is activated. TALK AROUND During interruptions in service (such as a power failure), you can continue to communicate by using the Talk Around feature. Talk Around allows you to communicate directly with other - Kenwood TK-7302H | Operation Manual - Page 15
When using an optional scrambler board, you can change the internal and external scrambler codes: 1 Press and hold the key programmed as Scrambler for 2 seconds. • "co" (code) appears on the display, followed by the current scrambler code. 2 Press to select your desired scrambler code. 3 - Kenwood TK-7302H | Operation Manual - Page 16
HORN ALERT The Horn Alert function can only be used with an optional relay unit. Press the key programmed as Horn Alert to toggle the Horn Alert function ON or OFF. • "HA" appears on the display while Horn Alert is activated. BACKGROUND OPERATIONS TIME-OUT TIMER (TOT) The Time-out Timer is used to - Kenwood TK-7302H | Operation Manual - Page 17
TK-7302/ TK-8302 TK-7302H/ TK-8302H - Kenwood TK-7302H | Operation Manual - Page 18
- Kenwood TK-7302H | Operation Manual - Page 19
Kenwood 150 Kenwood JVC KENWOOD Corporation. R-i - Kenwood TK-7302H | Operation Manual - Page 20
Kenwood Kenwood. 12В! Kenwood 1 3 4 5 6 DTMF...7 8 Режим FleetSync 2 9 10 12 R-ii - Kenwood TK-7302H | Operation Manual - Page 21
Kenwood Kenwood 1 10 A (TK-7302/ TK-8302 2 15 A (TK-7302H/ TK-8302H 2 1 5 x 16 4 4 4 4 1 12 1 2 3 4 R-1 - Kenwood TK-7302H | Operation Manual - Page 22
1 4,2 2 3 4 M4 x 6 мм 5 x 16 мм 12 В R-2 - Kenwood TK-7302H | Operation Manual - Page 23
:@ . ; ACC. = B> 2 8 a b 4}. c 4. d 4}. e TX/RX f g h S / A / - Kenwood TK-7302H | Operation Manual - Page 24
2 • AUX Talk Around OST S, A, - Kenwood TK-7302H | Operation Manual - Page 25
PS 1 3. 2 C A A 1 и 2 3 S G1" (Зона 1). 1 2 PTT PTT 3 - 4 R-5 - Kenwood TK-7302H | Operation Manual - Page 26
Sc 2 P 1 2 1 cA cd GA Gd". R-6 - Kenwood TK-7302H | Operation Manual - Page 27
PTT DTMF DTMF DTMF. 1 PTT. 2 Keypad Auto-PTT PTT DTMF 1 Ad". 2 1 ~ 9). 3 PTT 1 Ad". 2 0 rd 3 PTT R-7 - Kenwood TK-7302H | Operation Manual - Page 28
St". QT DQT) QT или DQT QT/ код DQT 2 2 2 DTMF DTMF DTMF FleetSync SELCALL 9. MDC-1200: MDC-1200 AFSK 1200 1200 Гц и 1800 Гц. OST) 16 пар OST. 1 2 ot OST. 3 B и C OST. 4 PTT 5 OST S. R-8 - Kenwood TK-7302H | Operation Manual - Page 29
Режим FleetSync 2 FleetSync 2 JVC KENWOOD Corporation. MDC-1200 FleetSync. MDC-1200 и FleetSync SELCALL Selcall 1 2 PTT Selcall PTT ID 3 Fleet и 4 ID Fleet и ID. ID 1 2 1 PTT List ID 1 2 2 10 до 99 (80 ~ - Kenwood TK-7302H | Operation Manual - Page 30
1 2 2 Ln". TALK AROUND Talk Around Talk Around Talk Around Talk Around Talk Around tA". Sr". R-10 - Kenwood TK-7302H | Operation Manual - Page 31
1 2 co 2 B и C 3 S 4 QT, DQT, DTMF или FleetSync. QT, DQT, DTMF или FleetSync 1 SL 2 B и C 0 до 9. 3 S PA) PA 1 PA". 2 PTT 3 R-11 - Kenwood TK-7302H | Operation Manual - Page 32
HA". TOT) PTT. AUX AU". BCL) BCL PTT ID PTT ID ID PTT. R-12
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
INSTRUCTION MANUAL
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER
TK-7302/ TK-8302
TK-7302H/ TK-8302H
© B62-2150-30 (M, M2, M4)
09 08 07 06 05 04 03