Kenwood TK-8302 User Manual 1

Kenwood TK-8302 Manual

Get Kenwood TK-8302 PDF manuals and user guides View all Kenwood TK-8302 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-8302 manual content summary:

  • Kenwood TK-8302 | User Manual 1 - Page 1
    INSTRUCTION MANUAL VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7302/ TK-8302 © B62‑2168‑10 (C) 09 08 07 06 05 04 03 02 01
  • Kenwood TK-8302 | User Manual 1 - Page 2
    are grateful you have chosen Kenwood for your personal mobile applications. This instruction manual covers only the basic operations etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if
  • Kenwood TK-8302 | User Manual 1 - Page 3
    of the vehicle before installing the transceiver. ◆ Use only the supplied DC power cable or a Kenwood optional DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable. For passenger safety, install the transceiver securely using the supplied mounting bracket and screw
  • Kenwood TK-8302 | User Manual 1 - Page 4
    : The following instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the cable (with fuses 1 • 10 A fuse 4 Mounting Bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • Hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Instruction manual
  • Kenwood TK-8302 | User Manual 1 - Page 5
    hex-headed screws. 4 Mount an optional microphone hanger in a location where it will be within easy reach of the user. • The microphone and microphone cable should be mounted in a place where they will not interfere with the safe operation of the vehicle. When replacing the fuse in the DC power
  • Kenwood TK-8302 | User Manual 1 - Page 6
    jack Insert the microphone plug into this jack. ⑦ Status Indicator Lights during a specified mode, based on dealer programming. ⑧ S / A / / keys Press to activate their programmable functions {page 4}. to this jack. ⑭ Power input connector Connect the DC Power Cable to this connector. 
  • Kenwood TK-8302 | User Manual 1 - Page 7
    display shows the channel number and the 2 dots show various modes of operation. The left and right dots on the display can be programmed to indicate specific modes of operation, as listed below. • AUX • Scan Delete/Add • External Speaker • Scrambler • Horn Alert • Talk Around • Lone Worker
  • Kenwood TK-8302 | User Manual 1 - Page 8
    the Volume Press the Volume Up key to increase the volume. Press the Volume Down key to decrease the volume. If Squelch Off has been programmed onto a key, you can use that function to listen to background noise while adjusting the volume level. Selecting a Zone and Channel Select the desired zone
  • Kenwood TK-8302 | User Manual 1 - Page 9
    the scanning sequence. Priority Scan If a Priority channel has been programmed, the transceiver will automatically change to the Priority channel when a list. 1 Select your desired zone and/or channel. 2 Press the key programmed as Scan Delete/Add to remove a channel or press and hold the key for
  • Kenwood TK-8302 | User Manual 1 - Page 10
    DTMF calls, you must use an optional microphone with a DTMF keypad. Manual Dialing 1 Press and hold the PTT switch. 2 Enter the desired (1 ~ 9). 3 Press the PTT switch to make the call. Redialing 1 Press the key programmed as Autodial or the microphone key. • "Ad" appears on the display. 2 Press the
  • Kenwood TK-8302 | User Manual 1 - Page 11
    are using the same channel. Optional Signaling Your dealer may also program several types of optional signaling for your transceiver channels. 2-tone is an Alphanumeric 2-way Paging Function and is a protocol owned by Kenwood Corporation. Note: If set up by your dealer, your transceiver may
  • Kenwood TK-8302 | User Manual 1 - Page 12
    as Paging Call for 1 second to transmit your PTT List ID, to request a call. Status Message You can transmit pre-programmed status messages by pressing the keys programmed as Status 1 and Status 2. Status messages are 2-digit codes ranging from 10 to 99 (80 ~ 99 are reserved for special messages
  • Kenwood TK-8302 | User Manual 1 - Page 13
    the display while Lone Worker is activated. Talk Around During interruptions in service (such as a power failure), you can continue to communicate by using away or there are no geographical obstacles in the way. Press the key programmed as Talk Around to toggle the Talk Around function ON or OFF. •
  • Kenwood TK-8302 | User Manual 1 - Page 14
    their transceivers. The scrambler function will not work with transceivers set up with different scrambler codes. Monitor/ Squelch Off You can use the key programmed as Monitor or Squelch Off to listen to weak signals that you cannot hear during normal operation and to adjust the volume when no
  • Kenwood TK-8302 | User Manual 1 - Page 15
    . PTT ID PTT ID is the transceiver unique ID code which is sent each time the PTT switch is pressed and/or released. Compander If programmed by your dealer for a channel, the compander will remove excessive noise from transmitted signals, to provide higher clarity of signals. Voice Announcement When
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
INSTRUCTION MANUAL
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER
TK-7302/ TK-8302
© B62-2168-10 (C)
09 08 07 06 05 04 03 02 01