Kenwood TK-D340 User Manual 1

Kenwood TK-D340 Manual

Get Kenwood TK-D340 PDF manuals and user guides View all Kenwood TK-D340 manuals
Add to My Manuals
Save this manual to your list of manuals

Kenwood TK-D340 manual content summary:

  • Kenwood TK-D340 | User Manual 1 - Page 1
    TK-D240 TK-D240V TK-D340 TK-D340U TK-D348R VHF DIGITAL TRANSCEIVER UHF DIGITAL TRANSCEIVER USER MANUAL B5A‑0933-00/02
  • Kenwood TK-D340 | User Manual 1 - Page 2
    CONTENTS PREPARATION...4 INSTALLING THE CHANNEL STOPPER 4 INSTALLING THE ANTENNA 4 INSTALLING/ REMOVING THE BATTERY PACK 5 INSTALLING THE BELT CLIP 5 INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS 6 INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET 7 ORIENTATION...8 PROGRAMMABLE
  • Kenwood TK-D340 | User Manual 1 - Page 3
    ADVANCED OPERATIONS 17 EMERGENCY CALLS...17 Lone Worker Mode...17 SCRAMBLER...17 MONITOR/ SQUELCH OFF 18 DMR...19 INDIVIDUAL/ GROUP CALLS 19 Receiving...19 BACKGROUND OPERATIONS 20 TIME-OUT TIMER (TOT 20 BATTERY SAVER...20 LOW BATTERY WARNING 20 BUSY CHANNEL LOCKOUT (BCL 20 PTT ID...21
  • Kenwood TK-D340 | User Manual 1 - Page 4
    PREPARATION INSTALLING THE CHANNEL STOPPER You can set the channel stopper position for channels 2, 4, 6, 8, 10, 12, and 14. Inserting the Channel stopper prevents unnecessarily selecting channels which do not exist. • Selecting a channel which does not exist causes a continuous error tone to sound.
  • Kenwood TK-D340 | User Manual 1 - Page 5
    INSTALLING/ REMOVING THE BATTERY PACK The battery pack is not charged at the factory; charge it before use. CAUTION ◆◆ Do not short the battery terminals or dispose of the battery by fire. ◆◆ Never attempt to remove the casing from the battery pack. 1 Align the battery pack with the back of the
  • Kenwood TK-D340 | User Manual 1 - Page 6
    INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS Install the cap over the speaker/ microphone jacks when not using an optional speaker/ microphone or headset. Note: ◆◆ To keep the transceiver water resistant, you must cover the speaker/ microphone jacks with the supplied cap. 1 Place the cap
  • Kenwood TK-D340 | User Manual 1 - Page 7
    INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE (OR HEADSET) Note: ◆◆ The transceiver is not fully water resistant when using a speaker/ microphone or headset. 1 Insert the speaker/ microphone (or headset) plugs into the speaker/ microphone jacks of the transceiver. 2 Place the locking bracket over the
  • Kenwood TK-D340 | User Manual 1 - Page 8
    ORIENTATION Microphone Antenna Speaker Battery pack a Selector Rotate to change the operating channel. b LED indicator For the LED indicator status, refer to page 13. c Power switch/ Volume control Turn clockwise to switch ON the transceiver. To switch OFF the transceiver, turn counterclockwise
  • Kenwood TK-D340 | User Manual 1 - Page 9
    PROGRAMMABLE FUNCTIONS The Selector, Side 1 and Side 2 keys can be programmed with the functions listed below. Ask your dealer for details on these functions. Note: ◆◆ The duration of pressing a key to activate a function is dependent on your dealer setting. Your dealer may have set some keys to be
  • Kenwood TK-D340 | User Manual 1 - Page 10
    n Emergency Places the transceiver into Emergency mode. Emergency mode is used to carry out emergency actions. Note: ◆◆ This function can be programmed only on the Side 1 key. n Home Channel Press this key to immediately select your home channel (pre-programmed by your dealer). n Home Channel Select
  • Kenwood TK-D340 | User Manual 1 - Page 11
    n Scan Delete/Add Adds or removes the selected Channel to or from the scan sequence. n Scrambler Toggles the Scrambler function ON and OFF. Note: ◆◆ This function cannot be used in certain countries. Contact your KENWOOD dealer for further information. n Squelch Off Press to hear background noise.
  • Kenwood TK-D340 | User Manual 1 - Page 12
    BASIC OPERATION SWITCHING POWER ON/OFF Turn the Power switch/ Volume control clockwise to switch the transceiver ON. Turn the Power switch/ Volume control counterclockwise fully to switch the transceiver OFF. Transceiver Password If your transceiver is password protected, the LED will light blue
  • Kenwood TK-D340 | User Manual 1 - Page 13
    • For best sound quality at the receiving station, hold the microphone approximately 1.5 inches (3 cm to 4 cm) from your mouth. RECEIVING Select the desired zone and channel. If signaling has been programmed on the selected channel, you will hear a call only if the received signal matches your
  • Kenwood TK-D340 | User Manual 1 - Page 14
    operation allows you to transmit hands-free. This feature must first be activated by your dealer, and can only be used if you are using a supported headset. VOX can be turned off for specific channels by your dealer. To activate VOX and set the VOX Gain level, perform the following steps
  • Kenwood TK-D340 | User Manual 1 - Page 15
    FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION FleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned by JVC KENWOOD Corporation. SELCALL (SELECTIVE CALLING) A Selcall is a voice call to a particular station or to a group of stations. Transmitting 1 Select your desired zone and
  • Kenwood TK-D340 | User Manual 1 - Page 16
    SCAN Scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops if a matching signal is present. To start/ stop scanning, press the key programmed as [Scan]. • When a signal is detected, Scan pauses at that channel. The
  • Kenwood TK-D340 | User Manual 1 - Page 17
    ADVANCED OPERATIONS EMERGENCY CALLS If your transceiver has been programmed with the Emergency function, you can make emergency calls. 1 Press and hold the key programmed as [Emergency]. • Ask your dealer for the length of time necessary to hold this key before the transceiver enters Emergency mode.
  • Kenwood TK-D340 | User Manual 1 - Page 18
    MONITOR/ SQUELCH OFF You can use the key programmed as [Monitor] or [Squelch Off] to listen to weak signals that you cannot hear during normal operation and to adjust the volume when no signals are present on your selected channel. Your dealer can program a key with one of 4 functions: • Monitor:
  • Kenwood TK-D340 | User Manual 1 - Page 19
    DMR DMR is a generic name for a digital communication system protocol utilizing 4-level FSK. In a DMR Conventional system, communications are realized by sending and receiving digital signals on a DMR digital channel. Using a DMR ID (Unit ID or Group ID) allows the various communications INDIVIDUAL/
  • Kenwood TK-D340 | User Manual 1 - Page 20
    BACKGROUND OPERATIONS TIME-OUT TIMER (TOT) The Time-out Timer is used to prevent you from using a channel for an extended duration. If you continuously transmit for a preset time, the transceiver will stop transmitting and a warning tone will sound. Release the PTT switch to stop the tone. BATTERY
  • Kenwood TK-D340 | User Manual 1 - Page 21
    PTT ID PTT ID is the transceiver unique ID code which is sent each time the PTT switch is pressed and/or released. Note: ◆◆ PTT ID can be made only in analog operation. SIGNALING QT/ DQT The Encoder/Decoder function uses QT/ DQT to segregate talk groups, so users only hear calls from their own group
  • Kenwood TK-D340 | User Manual 1 - Page 22
    © 2017
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
B5A‑0933‑00/02
VHF DIGITAL TRANSCEIVER
UHF DIGITAL TRANSCEIVER
USER MANUAL
TK-D240
TK-D340
TK-D348R
TK-D240V
TK-D340U