KitchenAid KBSD608EBS Dimension Guide
KitchenAid KBSD608EBS Manual
 |
View all KitchenAid KBSD608EBS manuals
Add to My Manuals
Save this manual to your list of manuals |
KitchenAid KBSD608EBS manual content summary:
- KitchenAid KBSD608EBS | Dimension Guide - Page 1
refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord. Water Pressure: A cold water supply with water support the refrigerator weight, more than 600 lbs (272 kg), door panels and contents of the refrigerator Installation Instructions packed with - KitchenAid KBSD608EBS | Dimension Guide - Page 2
refrigerator and a corner wall. NOTE: More clearance may be required if you are using overlay panels, custom handles, or extended handles on a Classic model. To adjust the door swings, see "Adjust Doors." 36" (91.4 cm) Models 42" (106.7 cm) Models 48" (121.9 cm) Models Model Instructions packed
-
1 -
2
 |
 |
PRODUCT MODEL NUMBERS
Side By Side Built-In Refrigerator
KBSD602E
KBSD606E
KBSD608E
KBSN602E
KBSN608E
Electrical:
A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply
is required. It is recommended that a separate circuit serving only your refrigerator
be provided. Use an outlet that cannot be turned off by a switch. Do not use an
extension cord.
Water Pressure:
A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have
questions about your water pressure, call a licensed, qualified plumber.
Reverse Osmosis Water Supply:
IMPORTANT:
The pressure of the water supply coming out of a reverse osmosis system
gwoing to the water inlet valve of the refrigerator needs to be between 30 and 120 psi
(207 and 827 kPa).
OPENING DIMENSIONS
To avoid tipping during use, the solid soffit must be within 1" (2.5 cm)
maximum above the refrigerator. If the solid soffit is higher than 1"
(2.5 cm) or one is not available, then the refrigerator must be braced.
If the anti-tip boards are needed, they must be attached to the rear wall
studs 80" to 90" (203 cm to 229 cm) above the floor. See “Install Anti-Tip
Boards” for more information.
NOTE:
A clearance of
Z\x
" (1.3 cm) above the top grille must
be maintained in order for the top grille to be removed.
IMPORTANT:
n
It is recommended that you do not install the refrigerator near an oven, radiator, or
other heat source.
n
Do not install in a location where the temperature will fall below 55°F (13°C).
n
Floor must support the refrigerator weight, more than 600 lbs (272 kg), door panels
and contents of the refrigerator.
Model
Width A (as shown above)
Dimension B (as shown above)
36
35
Z\x
" to 35
C\v
"
(90.2 cm to 90.8 cm)
4" (10.2 cm)
42
41
Z\x
" to 41
C\v
"
(105.4 cm to 106.1 cm)
7
Z\x
" (19.1 cm)
48
47
Z\x
" to 47
C\v
"
(120.7 cm to 121.3 cm)
13
Z\x
" (34.3 cm)
NOTE:
Flooring under refrigerator must be at same level as the room. Face of
cabinetry must be plumb.
PRODUCT DIMENSIONS
n
The depth from the front of the top grille to the back of the refrigerator cabinet is
5
C\₈
" (64.5 cm).
n
The power cord is 84" (213 cm) long.
n
Height dimensions are shown with leveling legs extended
Z\₈
" (3 mm) below
the rollers.
*When leveling legs are fully extended to 1
Z\v
" (3.2 cm) below rollers,
add 1
Z\₈
" (2.9 cm) to the height dimensions.
SIDE VIEW
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10681447A
7/15
Page 1 of 2