KitchenAid KHMS2050SSS Installation Guide
KitchenAid KHMS2050SSS - 30" Microwave Hood Combo Manual
 |
UPC - 883049023946
View all KitchenAid KHMS2050SSS manuals
Add to My Manuals
Save this manual to your list of manuals |
KitchenAid KHMS2050SSS manual content summary:
- KitchenAid KHMS2050SSS | Installation Guide - Page 1
in these installation instructions. Table of Contents MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2 Tools and Parts 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS 4 Remove Mounting Plate 4 Convert Microwave Oven to - KitchenAid KHMS2050SSS | Installation Guide - Page 2
the microwave oven will be installed. The location must provide: ■ Minimum installation dimensions. See "Installation Dimensions" illustration. ■ Minimum one 2" x 4" (50.8 x 101.6 mm) wood wall stud and minimum 3/8" (10 mm) thickness drywall or plaster/lath within cabinet opening. ■ Support for - KitchenAid KHMS2050SSS | Installation Guide - Page 3
Observe all governing codes and ordinances. Required: ■ A 120 Volt, 60 Hz, AC only, 15- or 20-amp electrical supply with a fuse or circuit breaker. Recommended: ■ A time-delay fuse or time-delay circuit breaker. ■ A separate circuit serving only this microwave oven. GROUNDING INSTRUCTIONS ■ For all - KitchenAid KHMS2050SSS | Installation Guide - Page 4
Mounting plate B. Back of microwave oven C. Tape (multiple locations) 3. Tape the microwave oven door closed so that door does not swing open while the microwave oven is being handled. NOTE: To avoid damage to the microwave oven, do not grip or use the door or door handle while the microwave oven - KitchenAid KHMS2050SSS | Installation Guide - Page 5
B. Damper assembly C. Long tab (inside slot) A. Vent opening B. Vent deflector 4. Secure vent deflector with 2 mounting screws (1 on each end). A B Roof Venting Installation Only To Remove Roof Damper Vent Cover: 1. Locate the roof damper vent cover on the top of the microwave oven. 2. Using - KitchenAid KHMS2050SSS | Installation Guide - Page 6
Wall Stud(s) NOTE: If no wall studs exist within the cabinet opening, do not install the microwave oven. 1. Using a stud finder, locate the edges of the wall stud(s) within the opening. See illustrations in "Possible Wall Stud Configurations." 2. Mark the center of each stud, and draw a plumb - KitchenAid KHMS2050SSS | Installation Guide - Page 7
of the opening. A Wall Venting Installation Only Centerline Upper cabinet bottom 4" (10.2 cm) ³⁄₈" (1 cm) A. Centerline 2. With the support tabs facing forward (see illustrations in "Possible Wall Stud Configurations" in "Locate Wall Stud(s)" section), align the mounting plate center markers - KitchenAid KHMS2050SSS | Installation Guide - Page 8
bolts. Wall Stud at One Corner Hole (Figure 3) 1. With the support tabs of the mounting plate facing forward, insert a 1/4-20 x 3" round-head bolt through the corner hole that fits over the 3/4" (19 mm) hole drilled in Step 3 of "Installation for Wall Stud at One Corner Hole" in the "Drill Holes in - KitchenAid KHMS2050SSS | Installation Guide - Page 9
needs to be installed around the supply microwave oven. 3. Using 2 or more people, lift microwave oven and hang it on support tabs at the bottom of mounting plate. A NOTE: To avoid damage to the microwave oven, do not grip or use the door or door handle while the microwave oven is being handled - KitchenAid KHMS2050SSS | Installation Guide - Page 10
breaker has not tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. ■ Check that the power supply cord is plugged into a grounded 3 prong outlet. ■ See the Use and Care Guide for troubleshooting information. Installation is now complete. Save - KitchenAid KHMS2050SSS | Installation Guide - Page 11
hood performance If venting through the wall, be sure that there is proper clearance within the wall for the damper to open fully. If venting through the roof, and rectangular to round transition is used, be sure there is at least 3" (7.6 cm) of clearance between the top of the microwave oven - KitchenAid KHMS2050SSS | Installation Guide - Page 12
model and serial number plate, which is located behind the microwave oven door on the front frame of the microwave oven. If you need additional assistance, call us at our toll free number or visit our website listed in the Use and Care Guide. Replacement Parts If any of the installation hardware
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
MICROWAVE HOOD COMBINATION
INSTALLATION INSTRUCTIONS
MICROWAVE HOOD COMBINATION SAFETY
This product is suitable for use above electric or gas cooking products up to and including 30" (76.2 cm) wide. See “Installation
Requirements” section for further notes.
These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in
these installation instructions.
Table of Contents
MICROWAVE HOOD COMBINATION SAFETY
..............................
1
INSTALLATION REQUIREMENTS
...................................................
2
Tools and Parts
...............................................................................
2
Location Requirements
...................................................................
2
Product Dimensions
.......................................................................
3
Electrical Requirements
..................................................................
3
INSTALLATION INSTRUCTIONS
.....................................................
4
Remove Mounting Plate
.................................................................
4
Convert Microwave Oven to External Venting
...............................
4
Locate Wall Stud(s)
.........................................................................
6
Mark Rear Wall
................................................................................
7
Drill Holes in Rear Wall
....................................................................
7
Attach Mounting Plate to Wall
........................................................
8
Prepare Upper Cabinet
...................................................................
8
Install the Microwave Oven
............................................................
9
Complete Installation
....................................................................
10
VENTING DESIGN SPECIFICATIONS
............................................
11
ASSISTANCE
...................................................................................
12
Replacement Parts
.......................................................................
12
W10189714A
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING