KitchenAid KRFF302EWH Instruction Sheet

KitchenAid KRFF302EWH Manual

Get KitchenAid KRFF302EWH PDF manuals and user guides View all KitchenAid KRFF302EWH manuals
Add to My Manuals
Save this manual to your list of manuals

KitchenAid KRFF302EWH manual content summary:

  • KitchenAid KRFF302EWH | Instruction Sheet - Page 1
    power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. Kit Contains: 2 Module Covers 2 Wire Harnesses 1 Ice Maker (with no Harness) 1 Shut Off Arm (with no Extension) 1 Instruction Sheet 1. Unplug refrigerator or disconnect
  • KitchenAid KRFF302EWH | Instruction Sheet - Page 2
    9. Turn ice maker assembly over and remove three screws from bottom of impinger to release ice maker. Set screws aside. See Figure 7. (3) screws 15. Pull grommet and harness through fan housing and pull other grommet off fan housing. See Figure 12. grommet figure 7 10. Remove thermal fuse from
  • KitchenAid KRFF302EWH | Instruction Sheet - Page 3
    25 cubic foot models ONLY 20. Use a straight blade screwdriver to remove the ice maker module cover. Remove H-Tap connector. Discard the old module cover. See Figure 16. NOTE: You may have a Type A or a Type B module. type A type b screw H-Tap connector figure 16 21. Turn ice maker assembly over
  • KitchenAid KRFF302EWH | Instruction Sheet - Page 4
    use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 40. Plug in refrigerator or reconnect power. 41. Check ice maker operation through normal service procedures. figure 25 33. Install shut off arm assembly onto new ice
  • KitchenAid KRFF302EWH | Instruction Sheet - Page 5
    la source de courant électrique avant l'entretien. Replacer pièces et panneaux avant de faire la remise en marche. Le non-respect de ces instructions peut causer un décès ou un choc électrique. Contenu de la trousse : 2 couvercles de module 2 faisceaux de câblage 1 machine à glaçons (sans faisceau
  • KitchenAid KRFF302EWH | Instruction Sheet - Page 6
    9. Inverser la machine à glaçons et enlever trois vis situées au-dessous du déflecteur d'air pour dégager la machine à glaçons. Conserver les vis à part. Voir la Figure 7. (3) vis 15. Tirer l'œillet et le faisceau dans le boîtier du ventilateur, puis l'autre œillet à l'extérieur du boîtier du
  • KitchenAid KRFF302EWH | Instruction Sheet - Page 7
    MODÈLES À 25 PI2 SEULEMENT 20. Utiliser un tournevis à lame plate pour enlever le couvercle du module de la machine à glaçons. Enlever le connecteur H-Tap. Jeter le vieux couvercle de module. Voir la Figure 16. REMARQUE : Un module de type A ou B peut être présent. type A type b vis CONNECTEUR
  • KitchenAid KRFF302EWH | Instruction Sheet - Page 8
    enlever la broche de liaison à la terre. Ne pas utiliser un adaptateur. Ne pas utiliser un câble de rallonge. Le non-respect de ces instructions peut causer un décès, un incendie ou un choc électrique. 40. Brancher le réfrigérateur ou reconnecter la source d'alimentation. 41. Vérifier que la machine
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Instruction Sheet W10885624
Rev A
8/16
Instruction Sheet
for Ice Maker kit
— 1 —
Kit Contains:
1.
Unplug refrigerator or disconnect power.
2.
Remove ice bin by depressing push button on side of ice
bin cover. Pull ice bin upward and slide out of ice box
compartment. See
Figure 1
.
2
Module Covers
2
Wire Harnesses
1
Ice Maker (with no Harness)
1
Shut Off Arm (with no Extension)
1
Instruction Sheet
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Failure to do so can result in death
or electrical shock.
Replace all parts and panels before
operating.
(continued)
FIGURE 1
PUSH
BUTTON
FIGURE 2
TAB
HARNESS
COVER
5.
Release tab on left front of ice maker and slide ice maker
auger assembly forward and out. See
Figure 4.
IMPORTANT:
Be sure to use the correct harness and module
cover for your unit. See
Figure 5.
6.
If you are working on a 22 cubic foot model, proceed to next
step. If you are working on a 25 cubic foot model, proceed
to step 20.
3.
Depress the tab holding the ice maker wire harness cover
and slide cover forward. See
Figure 2
.
4.
Disconnect harness. See
Figure 3
.
FIGURE 4
FIGURE 3
HARNESS
CONNECTOR
FIGURE 5
25 CUFT
22 CUFT
SWITCH
ICE MAKER MODULE COVER
22 CUFT
25 CUFT
SWITCH
CONNECTORS
THERMISTOR
THERMISTOR
GROMMET
22 CUBIC FOOT MODELS ONLY
7.
Use a straight blade screwdriver to remove the ice maker
module cover. Remove H-Tap connector. See
Figure 6.
NOTE:
You may see a Type A or a Type B module.
SCREW
H-TAP
CONNECTOR
TYPE B
TYPE A
FIGURE 6
8.
Disconnect connectors to switch in old module cover.
Remove switch from old module cover, set aside. Discard
old module cover.