KitchenAid KUDE60FXSS Dimension Guide

PRODUCT DIMENSIONS

Undercounter Dishwasher

®

PRODUCT MODEL NUMBERS

KUDC10FX

KUDC10IX

KUDE20FX

KUDE20IX

KUDE40FX

KUDE50CX

KUDE60FX

KUDE60HX

KUDE60SX

KUDE70FX

KUDL15FX

KUDS30CX

KUDS30FX

KUDS30IX

KUDS30SX

KUDS35FX

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Ref. W10321585

2/7/11

)

m

c

9

.

1

(

A.

Insulation may

be compressed.

(not used on all models)

)

m

c

2

.

2

6

(

)

m

c

6

.

0

6

(

1

2

"

)

m

c

3

.

3

5

(

"

0

3

"

7

2

)

m

c

8

.

8

6

(

"

3

3

3

"

(9.4 cm)

3

" -

4

"

B.

For panel ready models, dishwasher

depth is 24" (60 cm) not including the

®

handle, depth is 28"

A

B

C

C.

For

Pro Line

D

)

m

c

7

.

4

8

(

(70 cm).

(8.8 cm -10.6 cm)

Page 1 of 2

Electrical Requirements:

120-volt, 60-Hz, AC-only, 15- or

20-amp. fuesd electrical supply. Copper wire only. A

timedelay fuse or circuit breaker and separate circuit is

recommended.

If direct wiring dishwasher:

Use flexible, armored or

nonmetallic, sheathed copper

wire with grounding wire that

meets the wiring requirements for

your home and local codes and ordinances.

Use a U.L.-listed or CSA-approved conduit connector.

If connecting dishwasher with a power supply cord:

Use Power Supply Cord Kit (Part

No. 4317824) marked for use with

dishwashers. Follow the kit

instructions for installing the power supply cord.

Power supply cord must plug into a grounded

three-prong, outlet, located in the cabinet next to

the dishwasher opening. Outlet must meet all local

codes and ordinances.

Water Supply Requirements:

A hot water line with 20 to

120 psi (138 to 862 kPa) water pressure. Water

temperature must be 120°F (49°C) water at dishwasher.

Use

³⁄₈

" O.D. copper tubing with compression fitting or

flexible braided water supply line (

¹⁄₂

" minimum plastic

tubing is not recommended). Use a 90° elbow with

³⁄₄

"

N.P.T. external pipe threads on one end. Do not solder

within 6" (15.2 cm) from water inlet valve.

Drain Requirements:

A new drain hose is supplied with

your dishwasher. If this is not long enough, use a new drain

hose with a maximum length of 12' (3.7 m) (Part No.

3385556) that meets all current AHAM/IAPMO test

standards, is resistant to heat and detergent, and fits the 1"

(2.5 cm) drain connector of the dishwasher.

Make sure to connect the drain hose to waste tee or

disposer inlet above drain trap in house plumbing and 20"

(50.8 cm) minimum above the floor. It is recommended

that the drain hose either be

looped up and securely

fastened to the underside of

the counter, or be connected

to

an air gap.

Make sure to use an air gap

if the drain hose is

connected to house

plumbing lower than 20"

(50.8 cm) above subfloor or

floor.

Use

¹⁄₂

" (1.3 cm) minimum

I.D. drain line fittings.

If required, the air gap

should be installed in

accordance with the air gap installation instructions. When

connecting the air gap a rubber hose (not provided) will be

needed to connect to the waste tee or disposer inlet.

air gap

KitchenAid KUDE60FXSS Dimension Guide

KitchenAid KUDE60FXSS Manual

KitchenAid KUDE60FXSS manual content summary: