Kodak ESP 3 User guide - Page 50

Troubleshooting, Printer Fails to Power On, Device not Recognized - printer problems

Get Kodak ESP 3 - All-in-One Color Inkjet PDF manuals and user guides
UPC - 041771756932
View all Kodak ESP 3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Chapter 8 Troubleshooting Printer Fails to Power On Probable Cause The power supply is not properly connected. Corrective Action • Make sure the power cord is connected to the power supply and plugged into a grounded power outlet or power strip. • If you are using a power strip, make sure it is turned on. • If you are using a switched power outlet, make sure the switch is on. • Make sure the power outlet is supplying power. • If none of the above corrects the problem, contact Kodak support. Device not Recognized Probable Cause Any of the following can prevent your Kodak printer from reading a connected digital camera, USB thumb drive, or memory card. • The camera is turned OFF. • The USB connector from the camera is not fully inserted in the port. • The memory card is not completely inserted. • The memory card is in backwards. • The memory card file system is corrupt. • Make sure camera is in "connect" mode (PTP). • More than one memory card inserted. • The USB device is not supported. Corrective Action • Correct any connection problems and try again. • If the memory card file system is corrupt, reformat it in your camera. • Disconnect the unsupported device. 44 Kodak ESP 3 All-in-One

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
Chapter 8
Troubleshooting
Printer Fails to Power On
Probable Cause
The power supply is not properly connected.
Corrective Action
•
Make sure the power cord is connected to the power supply and plugged into a grounded
power outlet or power strip.
•
If you are using a power strip, make sure it is turned on.
•
If you are using a switched power outlet, make sure the switch is on.
•
Make sure the power outlet is supplying power.
•
If none of the above corrects the problem, contact Kodak support.
Device not Recognized
Probable Cause
Any of the following can prevent your Kodak printer from reading a connected digital camera, USB
thumb drive, or memory card.
•
The camera is turned OFF.
•
The USB connector from the camera is not fully inserted in the port.
•
The memory card is not completely inserted.
•
The memory card is in backwards.
•
The memory card file system is corrupt.
•
Make sure camera is in “connect” mode (PTP).
•
More than one memory card inserted.
•
The USB device is not supported.
Corrective Action
•
Correct any connection problems and try again.
•
If the memory card file system is corrupt, reformat it in your camera.
•
Disconnect the unsupported device.
44
Kodak ESP 3 All-in-One