Konica Minolta AccurioPress C4070 EF-107 User Guide
Konica Minolta AccurioPress C4070 Manual
View all Konica Minolta AccurioPress C4070 manuals
Add to My Manuals
Save this manual to your list of manuals |
Konica Minolta AccurioPress C4070 manual content summary:
- Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 1
- Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 2
Contents 1 Introduction 1.1 1.2 1.2.1 1.2.2 1.2.3 Introduction ...1-2 Safety Precautions...1-3 Notices for Safety ...1-3 Precautions When Replacing Units 1-4 Warning and Caution Labels...1-6 2 Installing Envelope Fusing Unit EF-107 2.1 2.2 2.2.1 2.2.2 Replacement Parts ...2-2 Installation - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 3
1 Introduction - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 4
replacing the machine units, please follow the instructions described in the User's Guide. To perform replacement tasks safely and reliably, keep this User's Guide and do not lose them. If you lose the document, please contact your service representative. Registered Trademarks KONICA MINOLTA, the - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 5
not to lose it. - Make sure you follow the safety precautions listed in the User's Guide. Warning and precaution symbols Be sure to observe the safety precautions. - This manual contains the instructions that should be strictly observed at all times to prevent injury to yourself and other persons as - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 6
1 1.2.2 Precautions When Replacing Units Preparation Tasks Before Replacing Units When replacing the units, be sure to receive instructions from our customer engineer, read the User' Guide in entirety and perform tasks in the specified order with appropriate tools. Do not perform any tasks that - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 7
between the plug terminals may cause a fire. Actions in Response to Troubles Do not keep using this product, if this product becomes inordinately hot the power outlet, and then call your Technical Representative or your authorized service representative. If you keep on using it as is, a fire or - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 8
be removed, you may fail to check a specific part to be alert for unexpected trouble or injury. If you find any warning or caution label removed or illegible due to soilage, please contact your service representative. Caution Labels on Fusing Part of Conveyance Fixing Unit CAUTION: High temperature - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 9
2 Installing Envelope Fusing Unit EF-107 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 10
the task. NOTICE When replacing the fusing unit, be sure to receive instructions from our customer engineer. NOTICE Please do not dispose of the packaging EF-107 1 2 Bottom auxiliary guide assy[A] *1 1 3 Side auxiliary guide assy[B] *1 2 4 Tip auxiliary guide/rear assy[C] *1 1 AccurioPress - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 11
front assy[C] *1 6 Bottom auxiliary plate assy[D] *1 7 Adjusting block assy *1 8 Guide shaft *1 2 Q'ty 1 1 2 1 *1: Packaged together with the Mount Kit MK-746. Use this part when Large Capacity Unit LU-202m/LU202XLm is installed on the main - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 12
release lever M1 [1] counterclockwise. NOTICE Please confirm that process unit has not been pulled out when pulling out the ADU drawer. 4 Open the paper exit guide [2] while releasing the lever M6 [1] at the bottom. Loosen the screw [3] (1 piece). AccurioPress C4080/C4070, AccurioPrint C4065 2-4 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 13
sure that the exit section is open before setting fusing unit to the machine. When you try to set the fusing unit with the exit guide unit closed, the machine may be damaged. AccurioPress C4080/C4070, AccurioPrint C4065 2-5 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 14
2.2 Installation Procedures 2 9 Holding the handles on the front and rear sides [2] of fusing unit [1] by both hands, slide the fusing unit [1] until it reaches to the rear side. Return the fixing plate [3] to its original position. 10 Tighten the screw [1] (1 piece) and close the exit section - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 15
Follow the procedure below to use envelopes of the above size. Auxiliary guides (2 pieces) are not needed. 1 Open the upper door. 2 in the arrowed direction, and remove it. 3 Install the bottom auxiliary guide assy [A] in the Large Ca- pacity Unit LU-202m/LU-202XLm tray. % Align the - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 16
229 mm) C6/C5 (114 x 229 mm) 5 Install the tip auxiliary guide/rear assy [C] (1 piece) and the tip auxiliary guide/front assy [C] (1 piece) to the paper guide side plate. % Align the installation hole in the tip auxiliary guide assy with the positioning pin. % Align the cutout of the tip auxiliary - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 17
K2 (240 x 332 mm) Envelopes The following parts need to be installed when K2 envelopes are used. - Bottom auxiliary guide assy [A] (1 piece) - Adjusting block assy (2 pieces) - Guide shaft (1 piece) 1 Open the upper door. 2 Remove the holding paper. % Hold the projection with your fingers and slide - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 18
, and install them. % Align the mark on the adjusting block assy with the mark on the indicating label. 2 K2 (240 x 332 mm) 5 Install the guide shaft to the back edge guide base of the bottom auxiliary guide assy [A]. 6 Close the upper door. AccurioPress C4080/C4070, AccurioPrint C4065 2-10 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 19
the holding paper. % Hold the projection with your fingers and slide the holding paper in the arrowed direction, and remove it. 3 Install the bottom auxiliary guide assy [A] in the Large Ca- pacity Unit LU-202m/LU-202XLm tray. % Align the positioning pin of the bottom auxiliary - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 20
382 mm) or K0 (287 x 382 mm) Envelopes The following parts need to be installed when K1 or K0 envelopes are used. - Bottom auxiliary guide assy [A] (1 piece) - Adjusting block assy (2 pieces) - Bottom auxiliary plate assy [D] (1 piece) NOTICE In the case of K1 or K0 envelopes, depending on the curl - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 21
[A] with the installation hole of the tray. % Align the detent of the bottom auxiliary guide assy [A] with the groove on the back end guide. 4 Hold the flap of the envelope to use and droop vertically. 5 Put the leading edge on a flat surface to check the curl di- rection and - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 22
the bottom auxiliary plate assy [D] with the mark line on the bottom auxiliary guide assy [A]. Align the edge of the PET sheet with the edge of the bottom auxiliary guide assy [A]. Then, install them. % Be sure to move the back edge guide base to the end edge. 8 Close the upper door. 2 Back edge - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 23
3 Removing Envelope Fusing Unit EF-107 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 24
3.1 Removal Procedures 3 3 Removing Envelope Fusing Unit EF-107 This section describes the procedures to remove Envelope Fusing Unit EF-107 and the feed auxiliary parts for envelopes. When using paper other than envelopes, follow the procedure below to replace the fusing unit and remove the parts - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 25
4 Copy/Print Operation - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 26
9.63"), Length: 148 to 375 mm (5.82" to 14.73") - Use auxiliary guides to load envelopes of 100 to 140 mm (3.92" to 5.50") in width when /C5, K2, N3, N4*) 50 sheetsv (K0, K1) *: The N4 envelope is supported only when the Large Capacity Unit LU202m/LU-202XLm is installed. Envelopes with a film window - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 27
4.1 Loading Envelopes in the Tray 4 4.1.1 Loading Envelopes in the Tray 5 of Paper Feeder Unit PF-707m 1 Pull out tray 5. 2 Widen the side guides and rear guide. 3 Place envelopes with the print side up. % Align the envelopes to the left side of the tray with the flaps on the right. 4 Align the - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 28
4.1 Loading Envelopes in the Tray 4 % Be sure to set the envelopes so that both sides of their leading edge and their flaps do not droop. OK NG 3 Adjust the guide shaft to the size of the envelope. AccurioPress C4080/C4070, AccurioPrint C4065 4-4 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 29
a paper weight of 80 g/m2 or less> 6 Remove the front edge lift up materials from the side of the bottom auxiliary guide assy [A]. 7 Install the front edge lift up materials on the bottom auxil- iary guide assy [A] as shown in the right figure. AccurioPress C4080/C4070, AccurioPrint C4065 4-5 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 30
mm) Envelopes 1 Open the upper door. 2 Set N4 or N3 envelopes on the bottom auxiliary guide assy [A], and adjust the guide shaft to the size of the envelope moving it to right and left. 3 Adjust both paper guide side plates to the size of the en- velop. 4 Close the upper door. Using K1 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 31
1/2 Envelopes 1 Open the upper door. 2 Set the envelops to use on the bottom auxiliary guide assy [A], and adjust the guide shaft to the size of the envelope moving it to right and left. 3 Adjust both paper guide side plates to the size of the en- velop. 4 Close the upper door. AccurioPress C4080 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 32
] on the Copy Screen. d Reference For details on Paper Setting, how to load originals, and how to make copy settings, refer to the HTML user's guide. - With Multi Bypass Tray MB-509 installed on the main body, only bypass tray can be selected. With Paper Feeder Unit PF-707m installed, only - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 33
perform your print operation. d Reference For details on Paper Setting, how to load originals, and how to make copy settings, refer to the HTML user's guide. AccurioPress C4080/C4070, AccurioPrint C4065 4-9 - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 34
5 Specifications - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 35
dimensions Width (crosswise direction): 100 to 245 mm (3.92" to 9.63") Auxiliary guide available range: 100 to 140 mm (3.92" to 5.50") (when Paper 241 152 229 162 229 114 240 332 120 235 90 205 N4 is supported only when the Large Capacity Unit LU-202m/LU-202XLm is installed. • Paper - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 36
sheets (K0, K1) Output tray: Approx. 50 sheets* (Output Tray OT-511) For other output options, please contact your service representative. * The N4 envelope is supported only when the Large Capacity Unit LU202m/LU-202XLm is installed. 200 (W) e 690 (D) e 235 (H) mm (Fusing unit: excluding projection - Konica Minolta AccurioPress C4070 | EF-107 User Guide - Page 37
http://konicaminolta.com