Konica Minolta AccurioPress C7100 IQ-501 Quick Guide

Konica Minolta AccurioPress C7100 Manual

Get Konica Minolta AccurioPress C7100 PDF manuals and user guides View all Konica Minolta AccurioPress C7100 manuals
Add to My Manuals
Save this manual to your list of manuals

Konica Minolta AccurioPress C7100 manual content summary:

  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 1
    IQ-501 Quick Guide KONICA MINOLTA
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 2
    during long printing for the job with Trim Margin /Execution When you start printing long job actually - Print the job by /Konica Minolta controller (A) /EFI controller (B) /CREO controller (C) NOTICE This manual describes the procedures for C3080 as an example. p.49 p.51 p.52 1
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 3
    (=Basic settings) 1 Load "Max density adjustment" paper into the tray 1. (Tray # is an example in this manual) ✔ As for selecting adjustment paper, please consult with service representative. In general, coated paper is recommended since color and density reproduction are stable. Load "the paper
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 4
    2/27/2020 5:45 PM／D11 2 Press the "Utility/Counter" key. 3 Press [Administrator Setting]. 4 If the [Administrator Password] screen is displayed, enter the administrator password using 8 to 64 one-byte characters, then press [OK]. ✔ The administrator password must be specified using 8 to 64 one-byte
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 5
    2/27/2020 5:45 PM／D11 7 Press [Quality Adjustment]. 8 Press [Custom Screen]. 9 Select [Dot190] for [Screen1] Press [OK]. 10 Press [Exit]. 4
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 6
    2/27/2020 5:45 PM／D11 11 Press [Adjustment] on the [MACHINE] screen. 12 Press [Quality Adjustment]. 13 Press [Color Density Control]. 14 Press [Basic Setting]. 5
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 7
    2/27/2020 5:45 PM／D11 15 Select each item as follows - [Use Color Density Control] > [ON] - [Periodical Adj. Execution] > [ON] - [Adjustment Execution timing] > [During Job Runs] - [Chart Tray Setting] > [OFF] Press [Next]. 16 Select each item as follows - [Adjustment Interval] > [ON] Press [Change
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 8
    PM／D11 18 Press [Image Diagnosis] NOTICE If [Image Diagnosis] is not displayed even IQ-501 is equipped, please contact your service representative. 19 Press [Basic Setting]. 20 Select each item as follows [DetailedDiagnosis/Sync.SimpleDiagnosis] > [ON] [Detailed Diagnosis Result Auto Reset] > [ON
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 9
    2/27/2020 5:45 PM／D11 22 Press [Package Color Auto Adj.]. 23 Press [Initial Set.]. 24 Select each item as follows For KM controller - [Screen of Adjustment Target] > [Screen1] - [Auto Selection] > [OFF] - [Gamma Auto. Adj.] > [ON] - [Dens. BalanceAdj.] > [ON
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 10
    2/27/2020 5:45 PM／D11 25 [Maximum Density Adjustment Tray] > [Tray1] Press [Next]. ("Max density adjustment paper is loaded into the tray 1 as an example.) 26 Select each item as follows - [Adjustment Tray] > [Tray2] - [Auto Run] > [OFF] - [Overwrite Tray Set. of Max.DensityAdj.] > [ON] Press [OK].
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 11
    2/27/2020 5:45 PM／D11 28 When the adjustment is completed, the adjustment result is displayed. Press [Close]. 29 Press [Initial Set.]. 30 Select each item as follows For KM controller - [Screen of Adjustment Target] > [Screen1] - [Auto Selection] > [ON] - [
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 12
    2/27/2020 5:45 PM／D11 31 Press [Next]. 32 Select each item as follows - [Adjustment Tray] > [Tray2] - [Auto Run]> [ON] if the print engine is turned ON and OFF every day - [Auto Run]> [OFF] if the print engine is running through the days and not turned OFF in daily use - [Overwrite Tray Set. of Max
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 13
    2/27/2020 5:45 PM／D11 Setting Summary of 1a. Daily Care [Loading paper] - Max density adjustment Paper Tray: [Tray 1] - The paper actually used for the job Tray: [Tray 2] [Custom Screen] - Screen1 : [Dot190] [Color Density Control] - Use Color Density Control]: [ON] - Periodical Adj. Execution: [ON]
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 14
    day, go to Step 1 to 6. If the print engine is running through the days and not turned OFF in daily use, go to Step 7 to 10 < Auto Run > 1 Turn ON the main power switch. The main power switch is located inside the machine and can be reached
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 15
    2/27/2020 5:45 PM／D11 4 The Package Auto Color Adjustment screen and Warm-up screen are displayed. 5 Automatically adjustment starts. 6 Adjustment charts are printed. 14
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 16
    2/27/2020 5:45 PM／D11 < Manual Execution > 7 Press [Adjustment] on the [MACHINE] screen. 8 Press [Quality Adjustment]. 9 Press [Package Color Auto Adj.]. 10 Press [Start]. ✔ The simplified image analysis chart and basic image diagnosis chart are printed out. 15
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 17
    2/27/2020 5:45 PM／D11 11 Adjustment charts are printed. 12 When the adjustment is completed, the adjustment result is displayed. 16
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 18
    withdraw the tray until a blue label shows on the rear-left side of the tray. Otherwise, the feed roller may not open or other machine trouble may be caused. 2 Turn the guide fixing knobs (2 pieces on front and rear side) counterclockwise to loosen them. 3 While pushing the side
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 19
    it to the left side. ■Be careful not to move the rear guide plate by force, otherwise it may be damaged. 5 Load paper so Tray 2 (lower tray). Also, do not load paper above the limit indicated on the side guide plate. Otherwise, a paper jam may be caused. Forcibly pushing the tray into the main body
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 20
    is securely aligned to the paper. If any gap is left between the rear guide plate and paper, the machine cannot detect the correct paper size, and machine trouble may be caused. 9 Push in the tray until it locks into place. The Amount indicator of the tray will change From " " to " " on
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 21
    to hold the lock release lever of the front one and the handle of the rear one. If moved only with the front side guide plate, the side guide plates may not be fixed in position. 12 Place around 100 sheets of paper into the tray with the print side up. Pushing
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 22
    the position of the top edges of the side guide plates. Move top edges of the side guide plates to align them to the paper, then turn the four side guide fixing knobs clockwise to fix the guides. NOTICE Avoid making the gap between the side guide plates too wide or too narrow for the
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 23
    is securely aligned to the paper. If any gap is left between the rear guide plate and paper, the machine cannot detect the correct paper size, and paper jams or machine trouble may be caused. 19 Push in the tray until it locks into place. The paper level indicator of the tray
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 24
    to turn the sub power switch ON. ■ Only one tray can be withdrawn at a time. 21 Move the front and rear side guide plates closer until they stop. Turn the side guide fixing knobs (4 pieces) of the side guide plate counterclockwise to loosen them. Pushing the lock release lever of the front side
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 25
    side of the tray. Pushing the lock release lever of the rear guide plate, align it to the edge of the paper. NOTICE ■ Do not load any gap is left between the rear guide plate and paper, the machine cannot detect the correct paper size, and paper jams or machine trouble may be caused. 25 Push in
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 26
    . 28 Place around 100 sheets of paper into the tray with the print side up. Pushing the lock release lever of the side guide plate, align the side guide plate to the paper. 29 Turn the bottom plate fixing knob counterclockwise to loosen it, slide it to the front, and turn it
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 27
    the position of the top edges of the side guide plates. Move top edges of the side guide plates to align them to the paper, then turn the two side guide fixing knobs clockwise to fix the guides. NOTICE Avoid making the gap between the side guide plates too wide or too narrow for the
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 28
    is securely aligned to the paper. If any gap is left between the rear guide plate and paper, the machine cannot detect the correct paper size, and paper jams or machine trouble may be caused. 34 Push in the tray until it locks into place. The paper level indicator of the tray
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 29
    . ■ Only one tray can be withdrawn at a time. 36 Open the small size guides provided for each of the front and rear side guide plates. NOTICE Leave the fixing levers of the paper control panels in the fixed position. NOTICE ■ Do not load above the limit level indicated on the small size guides. 28
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 30
    is securely aligned to the paper. If any gap is left between the rear guide plate and paper, the machine cannot detect the correct paper size, and paper jams or machine trouble may be caused. 40 Push in the tray until it locks into place. The paper level indicator of the tray
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 31
    plate does not move down. Be sure to turn the sub power switch ON. 42 Adjust the position of side guide plate(left). Turn the side guide fixing knobs (4 pieces) of the side guide plate counterclockwise to loosen them. 30
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 32
    43 Move the two side guide plates(left) to an appropriate position according to the size indication provided on the top of the guide plates. 44 Turn the two side guide fixing knobs of the side guide plates(left) clockwise to fix the guides. 31
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 33
    the size indication provided on the tray bottom plate. Turn the two side guide fixing knobs of the rear guide plate clockwise to fix the guides. For LU-202XL/XLm While pushing the rear guide lock release lever, move the rear guide plate to match the paper size indicator of the tray bottom plate. 46
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 34
    is securely aligned with the loaded paper. If making the space between the rear guide plate and paper too wide or too narrow, paper jams or machine trouble may be caused. 49 Close the top door(s). The paper level indicator of the tray changes from " " to " " on the [MACHINE] screen and [COPY
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 35
    2/27/2020 5:45 PM／D11 < Auto Measure > 50 Press [Paper Setting] on the [MACHINE] screen. 51 Press the tray in which the paper to be adjusted has been loaded. Press [Change Set]. 52 Press [Both Sides Adj.]. 53 Press [AutoMeasure], then press [Print Mode]. 34
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 36
    2/27/2020 5:45 PM／D11 54 When the [Print Mode] screen is displayed, enter three as a number of adjustment charts, and press [Start] on the control panel. Up to 20 adjustment charts can be printed out. As the number of charts increases, the accuracy of adjustment values rises. 55 The [AutoMeasure]
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 37
    2/27/2020 5:45 PM／D11 57 When the [Print Mode] screen is displayed, press [Start] on the control panel. 58 Check Front-Back registration gap. If registration gap is not good, increase number of adjustment charts and repeat step 53 to 57 again. 59 Press [Exit PrintMode]. 60 Press [Cancel]. 36
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 38
    2/27/2020 5:45 PM／D11 61 Press [Close]. 62 Return to the [MACHINE] screen. 37
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 39
    mm or more, Standard-size paper other than SRA3, 13 x 19, 12 x 18, and SRA4(SEF) can be adjusted automatically. For details, contact your service representative. < Confirmation of Auto Image Adj. settings(=default setting) 2 Press [Utility/Counter] on the control panel. 3 Press [User setting]. 38
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 40
    2/27/2020 5:45 PM／D11 4 Press [Common Setting]. 5 - [Back Side Magnification Adjustment] > [ON] Press [Next]. 6 Press [Next]. 7 - [Center Crop Mark Trim Margin] > [1.0 mm] Press [Next]. 8 Press [Next]. 39
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 41
    2/27/2020 5:45 PM／D11 9 Press [Next]. 10 Select each item as follows - [Select Chart Type(Auto Image Adj.)] [62-74g/m2]/[16-19 lb Bond]:[Type1] [75-80g/m2]/[20-21 lb Bond]:[Type1] [81-91g/m2]/[22-24 lb Bond]:[Type1] [92-105g/m2]/[25-28 lb Bond]:[Type1] [106-135g/m2]/[29-36 lb Bond]:[Type1] [136-
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 42
    2/27/2020 5:45 PM／D11 < Package Color Auto Adj. incl Color Density Control > 12 Press [Adjustment] on the [MACHINE] screen. 13 Press [Quality Adjustment]. 14 Press [Package Color Auto Adj.]. 41
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 43
    2/27/2020 5:45 PM／D11 15 Press [Start]. ✔ The simplified image analysis chart and basic image diagnosis chart are printed out. 16 Adjustment charts are printed. 17 When the adjustment is completed, the adjustment result is displayed. 42
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 44
    2/27/2020 5:45 PM／D11 < Both side adjustment > 18 Press [Paper Setting] on the [MACHINE] screen. 19 Press the tray in which the paper to be adjusted has been loaded. Press [Change Set]. 20 Press [Both Sides Adj.]. 21 Press [AutoMeasure], then press [Print Mode]. 43
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 45
    2/27/2020 5:45 PM／D11 22 When the [Print Mode] screen is displayed, enter three as a number of adjustment charts, and press [Start] on the control panel. Up to 20 adjustment charts can be printed out. As the number of charts increases, the accuracy of adjustment values rises. 23 The [AutoMeasure]
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 46
    2/27/2020 5:45 PM／D11 25 When the [Print Mode] screen is displayed, press [Start] on the control panel. 26 Check Front-Back registration gap. When registration gap is not good enough, increase number of adjustment charts and repeat step 53 to 57 again. 27 Press [Exit PrintMode]. 45
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 47
    2/27/2020 5:45 PM／D11 28 Press [Cancel]. 29 Press [Close]. 30 Return to the [MACHINE] screen. Setting Summary of 3a. [Confirm paper size] - Paper size: [SRA3],[13 x 19],[12 x 18], [SRA4(SEF)] [Auto Image Adjustment(default settings)] - Back Side Magnification Adjustment : [ON] - Center Crop Mark
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 48
    5:45 PM／D11 3b. Keep registration and constant color during long printing for the job with Trim Margin /Execution Print the job - Konica Minolta controller/APPM, Printer driver >> A - EFI controller/CWS(v6,v5), Printer driver >> B - CREO controller/IC-314) >> C < Print the job >
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 49
    2/27/2020 5:45 PM／D11 B Print long job with following settings EFI Command Work Station(ver.6) Open Job Properties and go to [Image]Tab > [Real time adj.] ([Color gradation] for ver.5) - [Auto Image Adjustment] > [Position + Gradation] Printer driver
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 50
    2/27/2020 5:45 PM／D11 4a. Keep registration and constant color during long printing for the job without Trim Margin / Preparation Color Density Control setting >>: Step 1 to 7 Periodical Both Side Adjustment setting >>: Step 8 to 9 < Color Density Control setting > 1 Press [Adjustment] on the [
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 51
    2/27/2020 5:45 PM／D11 4 Press [Basic Setting]. 5 Select each item as follows - [Use Color Density Control] > [ON] - [Periodical Adj. Execution] > [ON] - [Adjustment Execution timing] > [During Job Runs] - [Chart Tray Setting] > [OFF] Press [Next]. 6 Select each item as follows - [Adjustment
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 52
    2/27/2020 5:45 PM／D11 < Periodical Both Side Adjustment setting > 8 Press [Periodical Both Sides Adj.]. 9 Select each item as follows - [Period. Both Sides Auto Adj.] > [ON] - [Adjustment interval] > [1000 Sheet] - [Deviation Check] > [OFF] Press [OK]. Setting Summary of 4a. [Color Density Control]
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 53
    D11 4b. Keep registration and constant color during long printing for the job without Trim Margin /Execution Print the job - Konica Minolta controller/APPM, Printer driver >> A - EFI controller/CWS(v6,v5), Printer driver >> B - CREO controller/IC-314) >> C < Print the job >
  • Konica Minolta AccurioPress C7100 | IQ-501 Quick Guide - Page 54
    2/27/2020 5:45 PM／D11 B Print long job with following settings EFI Command Work Station(ver.6) Open Job Properties and go to [Image]Tab > [Real time adj.] ([Color gradation] for ver.5) - [Auto Image Adjustment] > [Off] Printer driver(EFI controller)
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
IQ-501 Quick Guide
KONICA MINOLTA