Konica Minolta PS7000 PS7000 Operator Manual (PC Version)
Konica Minolta PS7000 Manual
View all Konica Minolta PS7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Konica Minolta PS7000 manual content summary:
- Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 1
0818-7702-23 PS7000 PC version Operator´s Manual - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 2
should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. Please read the next section before using this device. It contains important information related to user safety and preventing equipment problems. Make sure you observe all of - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 3
these conditions be found, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. • In principle, do not use an extension cord. Use of an extension cord could cause a fire or electrical shock. Contact your authorized - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 4
smoke, or unusual odor or noise, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. If you keep on using it as is, a fire or electrical shock could result. • If this product has been dropped or its cover damaged - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 5
CAUTION • Do not use flammable sprays, liquids, or gases near this product, as a fire could result. • Do not leave a toner unit or drum unit in a place within easy reach of children. Licking or ingesting any of these things could injure your health. • Do not let any object plug the ventilation holes - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 6
. Failure to do this could damage the cord or cable, resulting in a fire, electrical shock, or breakdown. • When moving this product, always hold it by the locations specified in the operator's manual or other documents. If the unit falls it may cause severe personal injury. The product may also - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 7
other gases or chemicals are present. Failure to do so may shorten the service life of the product, cause damage or decrease performance. • Do not use an environment with a temperature outside the range specified in the operator's manual, as a breakdown or malfunction could result. • Do not attempt - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 8
any questions or comments about Minolta, our product or service, please let us know. Our fax number is 800-237-8087 (for U.S.A. and Canada). Thank you again. This operator's manual explains how to operate the unit and replenish its supplies. It also gives some troubleshooting tips as well as general - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 9
Book Scanner (herein after referred to as the Scanner). This operator's manual includes precautions for installation/operation of the Scanner, a system outline, an explanation of the Driver software, operation procedures for the Scanner, troubleshooting with the instruction manual, may cause - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 10
iii Introduction Copyright Books, magazines, journals and other materials may be copyrighted. Unauthorized appropriate. Post a copy of the above notice where it will be clearly visible to users of the scanner. Scanning into a computer and subsequent printing of the following is also prohibited by law - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 11
in conformity with the specifications below. This declaration is valid for the area of the European Union (EU) only. Product Type Book Scanner Product Name PS7000 Options Foot Switch, Grayscale Memory Board Accessory PC I/F Kit Standards Safety EMC : EN60 950 / 1992 A1, A2, A3, A4 (Safety - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 12
, transcribed, stored in a retrieval scanner, or translated into other languages without prior written consent from Minolta Co., Ltd. Trademark Acknowledgments Minolta is a registered trademark of Minolta Co., Ltd. Microsoft, Windows, Windows 95, 98 and Windows NT are registered trademarks of - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 13
installation and operation of the Scanner. Chapter 2 Overview An overview of the features, system configuration, functions and part names for each section and control panel. Chapter 3 PS7000 Twain Driver Describes installation and start-up procedures for the Twain Driver, as well as the options - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 14
the Scanner 1-4 Chapter 2 Overview Features 2-1 System configuration 2-2 PC version (connected to a personal computer 2-2 PR version (connected to a printer 2-2 Part identification and functions 2-3 Control panel keys 2-5 Functions of control panel keys 2-6 Chapter 3 PS7000 Twain Driver - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 15
Original Type 5-43 Selecting Output Scale 5-44 Selecting Contrast 5-45 Operations in Utility mode 5-47 Initial settings 5-48 Time Set 5-50 Caution 5-52 SCSI port settings 5-54 Exiting Utility mode 5-55 Chapter 6 Troubleshooting Potential problems 6-1 Warning message 6-1 Error message - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 16
ix Contents Chapter 7 Maintenance Maintenance 7-1 Daily checks 7-1 Cleaning 7-1 Chapter 8 Specifications Product specifications 8-1 For Key Operator's Use 8-3 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 17
x Contents - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 18
Precautions for Installation & Operation Chapter 1 Chapter 1 Precautions for Installation & Operation - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 19
book table is less than 1000 lx (e.g. 4.5 m x 6.5 m area with ceiling height of 2.6 m, and 12 or less 40 W fluorescent lamps). N A place where light from the lighting system or the outside through windows does not reflect on the steel mirror or hit the Scanner Scanner Scanner. N If Scanner's - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 20
975 mm 38-3/8" Precautions for Installation & Operation Chapter 1 1-2 Installation Moving the Scanner Please contact your authorized dealer before moving the Scanner to a new installation location. Space requirements N Secure the recommended space shown in the figure below to ensure easy operation - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 21
a damaged or cracked power cord or interface cable unrepaired. If any of these conditions are found, immediately shut down the Scanner, unplug the power cord, and call your authorized dealer for appropriate action. N NEVER place an object on the lamp unit. N ALWAYS completely insert the power cord - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 22
When moving the Scanner, be sure to disconnect the power cord and the interface cable. N When transporting the Scanner, contact your authorized Dealer. NOTE Never hold any parts other than the parts identified with arrows in the figure (e.g.,lamp cover, book table), or the Scanner may have trouble. - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 23
Precautions for Installation & Operation Chapter 1 1-5 Operation - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 24
Overview Chapter 2 Chapter 2 Overview - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 25
2-1 Features The Scanner is designed to scan books set face up on the book table. This makes setting the book very easy and reduces concerns that the book may be creased or damaged. In addition, warped text lines and text compression are corrected, ensuring clearer images. Various options such as a - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 26
to a printer) The Scanner is connected to a dedicated printer, allowing scanned images to be printed out directly. N This manual describes the PC version. NOTE • Connection to a personal computer and printer can be switched using [Output] in the [User Mode] menu. • A dedicated printer and the - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 27
and functions 1 9 8 2 3 4 5 10 11 6 7 12 13 16 18 15 14 17 19 1. Scanner unit: 2. Lamp unit: 3. Control panel: 4. Shading plate: 5. Steel mirror: 6. Book table: 7. Table center: 8. Start key: 9. Power switch: 10. Printer connector: 20 The CCD sensor housed in this unit scans the original - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 28
2-4 Part identification and functions Overview Chapter 2 11. SCSI connector: Connect the SCSI cable included in the interface kit. When multiple SCSI devices are connected to the personal computer, connect the Scanner at the end of the SCSI chain. (Optional PC interface kit is required) The total - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 29
Spread Single Text 8 Book Split Photo Panel Reset 9 6 Adjusts the contrast (luminosity) of the display. Allows you to customize settings. Recalls settings previously registered in User Mode. Displays the current settings. Displays current status, operation instructions, warning messages, and - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 30
Data Sheet Eras put ious Spread Single Book Split Text Photo Panel Reset Refer to page 5-16 "Menu flow chart" for details of each menu. 3. Job Recall key Recalls settings previously registered in User Mode. Pressing this key displays preset programs (scanner settings). The desired program can be - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 31
settings. Contrast User Mode Job Recall Mode Check FRAME MASK FINGER MASK CENTER ERASE ORIGINAL CONNECTION ON CENTERING OFF OFF OFF Book Auto Next PC Spread Single Book Split Text Photo Panel Reset Overview Chapter 2 5. Display Operating status, operation instructions, warning messages - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 32
Split: Right and left pages are scanned separately. Contrast User Mode Job Recall Mode Check Spread Single Book Split Text Photo Panel Reset Overview Chapter 2 8. Image key The image type can be selected to suit the original. The lamp of the selected mode lights. Text: Suitable for scanning - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 33
power switch is turned on. Contrast User Mode Job Recall Mode Check Spread Single Book Split Text Photo Panel Reset Overview Edit Finger masking Centering Exposure Resolution Size Quality Original Type Scale Contrast Default Setting PC Book mode Spread Text OFF (width: 5 mm, position: - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 34
PS7000 Twain Driver Chapter 3 Chapter 3 PS7000 Twain Driver - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 35
following are the minimum system requirements for the computer connected to the Scanner to install the Driver. PS7000 Twain Driver Chapter 3 Computer OS Required memory Application software Recommended SCSI Host Adapter Compatible with IBM PC/AT WindowsNT4.0, Windows95, Windows98 Grayscale Scan - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 36
PS7000 Twain Driver Chapter 3 3-2 Installation Installation procedure Follow the procedure below to install the Driver. *Screens may differ slightly depending on the Windows version. 1 Check that the Scanner is connected to the personal computer. 2 Turn on the power switch of the Scanner (refer to - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 37
PS7000 Twain Driver Chapter 3 3-3 Installation 5 Double-click [Add/Remove Programs]. 6 Select the [Install/Uninstall] tab. Click the [Install...] button. 7 A screen appears informing you that the driver is preparing for set up. - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 38
PS7000 Twain Driver Chapter 3 8 The installation confirmation screen appears. Click the [Next >] button to start installation. 9 The to complete installation. 3-4 Installation NOTE Eject the installation floppy disk from the computer and restart Windows after installation has been completed. - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 39
PS7000 Twain Driver Chapter 3 3-5 Uninstall Remove the Driver from the computer when it is no longer required. Uninstall procedure 1 Click the [Start] button and select [Settings] → [Control Panel]. 2 Double-click [Add/Remove Programs]. 3 Select the [Install/Uninstall] tab. Select [PS7000 Twain - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 40
File?" screen appears. Click the [Yes to All] button. 6 The screen indicates the shared files are being deleted. Click the [OK] button when completed. 3-6 Uninstall PS7000 Twain Driver Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 41
PS7000 Twain Driver Chapter 3 3-7 Start-up The Driver can be started from any Twain compatible application. The start up procedure when using Adobe Photoshop 4.0 is described below. 1 Start Adobe Photoshop 4.0. Select [File] → [Import] → [Select Twain_32 Source]. 2 Select [MINOLTA PS7000 32bit] in - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 42
4 A screen with basic settings for -1 reading images appears. 3-8 Start-up PS7000 Twain Driver Chapter 3 4 Click the [Detail] tab to show the -2 detailed setting screen. NOTE Relevant settings on the image acquisition screen must be completed before the image - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 43
versa. Each item is described below, with the corresponding Scanner setting indicated by a reference page. Refer to the specified page for details. 2 3 1 4 10 5 11 6 12 13 7 14 8 PS7000 Twain Driver Chapter 3 1. Scan Setting: 2. Delete: 3. Save: 4. Scan Size: 5. Resolution: 9 15 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 44
(Photo). Select [Auto] or [Manual]. Brightness is adjusted manually when [Manual] is selected. Brightness is adjusted automatically same as the start buttons on the Scanner. Click the [Spread Scan] button to read both pages of the book on the table. This button is . PS7000 Twain Driver Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 45
Detection] automatically determines the center of the original. This is effective only in Book mode. The center of the book table is regarded as the center of original when [Center fixed] is selected. " on page 5-45 for details. Exit the image acquisition screen. PS7000 Twain Driver Chapter 3 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 46
PS7000 ISIS Driver Chapter 4 Chapter 4 PS7000 ISIS Driver - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 47
environment The following are the minimum system requirements for the computer connected to the Scanner to install the Driver. PS7000 ISIS Driver Chapter 4 Computer OS Memory Application software Recommended SCSI Host Adapter Compatible with IBM PC/AT WindowsNT4.0, Windows95 At least 32MB of PC - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 48
connected to the personal computer. 2 Turn on the power switch of the Scanner (refer to "Turning on" on page 5-3), and then turn the personal computer on to start Windows. [When using Windows95] Select [Driver from disk provided by hardware manufacturer] and click the [OK] button when the following - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 49
The installation confirmation screen appears. Click the [Next >] button to start installation. 7 PS7000 is supplied with an application software "PixView" for ISIS. To install this software after the installation of the ISIS driver, select "Yes" and click the [Next] button. To use other software for - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 50
the instructions that will appear on the screen. 10 The complete setup confirmation screen appears. Click the [Finish] button to complete installation. 4-4 Installation PS7000 ISIS Driver Chapter 4 NOTE Eject the installation floppy disk from the computer and restart Windows after installation - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 51
any ISIS compatible application. The start up procedure when using PixView 3.0 is described below. 1 Start PixView 3.0. Select [File] → [Select Scanner]. 2 Select [Minolta PS7000] in the Select Source screen and click the [Select] button. 3 Click [Scan Setup] button. PS7000 ISIS Driver Chapter 4 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 52
4 A screen with Scanner settings for -1 reading images appears. 4 Click the [More] button to show the -2 Special Feature setting screen. 4-6 Start-up PS7000 ISIS Driver Chapter 4 Relevant settings on the image acquisition screen must be completed before the image is loaded to the personal - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 53
function settings made from the personal computer using the Image acquisition screen. Each item is described below, with the corresponding Scanner setting indicated by a reference page. Refer to the specified page for details. 3 4 5 6 1 2 14 7 15 8 9 10 11 12 13 PS7000 ISIS Driver Chapter 4 16 17 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 54
4-8 Image acquisition screen PS7000 ISIS Driver Chapter 4 1. Dot per manually when [Manual] is selected. Validates the settings. Initializes all the set values. Exit the image acquisition screen. Select [Spread] (scanning both pages), [Single] (scanning either right or left page only), or [Book - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 55
PS7000 ISIS Driver Chapter 4 4-9 Image acquisition screen 12. Automatic Brightness: 13. Scanning Method: 14. Type of Original: 15. Book Compensation /Sheet: 16. OK: 17. Cancel: Brightness is adjusted automatically according to the original when [Auto] is selected, however, further fine adjustment - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 56
Chapter 5 Operation Operation Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 57
careful not to knock your head against the scanner unit. Do not hold the sides when pushing the book table down, or your hands or fingers may be caught. Place your hand on the top surface of the table. Do not look directly at the lamp light visible through the front slits or - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 58
or five minutes in the Utility mode. Full intensity The Scanner's lamp lights at full intensity when the Scanner is reading the original. The lamp returns to half intensity after scanning is completed. NOTE The halogen lamp used in the Scanner is safe and not hazardous to health. However, never look - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 59
the start key turns red. The Scanner can be operated when the start key turns green. Start key NOTE When the SCSI cable is not connected properly, Images cannot be loaded if the PC interface cable is not connected properly. When the message [Start Appli./Driver] appears on the display, turn the - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 60
Turning off 1 Turn the switch off ("O" position). 5-4 Turning the Scanner ON and OFF NOTE • Never turn the power switch off while the Scanner is reading the original. • Turn off the personal computer before turning off the Scanner. Operation Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 61
original Place the original face up on the book table, aligning the top edge of the book with the stopper on the book table, and the spine of the book with the center mark. Check that the original is positioned with the corresponding size guide, if possible. When placing the original, observe the - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 62
Chapter 5 3 Place the original face up on the book table, aligning the top edge of the book with the stopper on the book table, and the spine of the book with the center mark. Check that the original is positioned with the corresponding size guide, if possible. NOTE In placing the original, make - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 63
. Spread: Entire area (both pages) is scanned as one sheet. Single: Only one page (right or left) is scanned. Book Split: Both pages are scanned separately, one page at a time. The lamp of the selected mode lights. 5 Hold the edges of both pages in the middle with your hands, and press the - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 64
original is placed in the effective Auto Focus range. 6 Press the Start key. Either key can be pressed when [Spread] is selected. When [Single] or [Book Split] is selected, press the key on the side to be scanned. The pressed Start key turns red and scanning is started. When scanning is - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 65
into the space enclosed by the scanner unit and the right and left edges of the book, or the Scanner will not be able to obtain Scanner fails to read the original correctly, a buzzer goes off, a warning message appears on the display, and scanning is stopped. Refer to page 6-2 "Troubleshooting - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 66
°, proper correction may not be made. Auto focus This function is available only to Book mode. The original height is detected, and the focal point of the Scanner can be adjusted to be within a range from 0 to 65 mm above the book table according to the detected original height. Operation Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 67
can be set to be within a range from 0 to 50 mm above the book table in 6 steps in 10 mm increments. When scanning a solid surface, adjust the detection. Set each function as follows to cancel the Auto function. • Expo (Manual) • Zoom (Fixed magnification) • Cent Eras (OFF) • Masking (OFF) • - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 68
4.Foot 5.Head 6.Guter The Scanner is designed for exclusive use in scanning images from a book or file. Note, however, that it may not make reliable images from any of the following types of originals. (If a warning message appears, refer to page 6-2 "Troubleshooting for warning messages".) If any - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 69
the top edge of the original, place the original upside down on the book table for scanning. If bookmarks are placed in the original, put them mm Operation Chapter 5 Bookmark 4. Originals with both text and photographs The Scanner provides you with two Image modes, Text and Photo. When an original - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 70
so that the binding section is lowered to the extent that the Auto Focus function is 65 mm effective. Push the center of the book table with your hands (see figure). The depth can be adjusted to two levels. Push down either side of the table and release it to - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 71
requiring special attention for the binding section An optional angle book holder is used to fix the opening angle of the book when scanning a valuable book whose binding must be carefully protected. 1 Assemble the angle book holder as shown in the figure. 2 Insert the holder into the groove on - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 72
to 20 mm (in 2.5 mm increments). Output Select an external device (printer or personal computer) to be connected to the Scanner. Previous Auto set (Available only in Book mode) Cent set -2.5 mm Wide +2.5 mm Wide OK PC Printer OK * Select [OK] to return to the main menu. Job Recall Recalls - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 73
set.) 17 X 23 14 X 22 14 X 17 11 X 17 11 X 14 LGL LTR H.LT 17 X 14 17 X 11 14 X 11 LGL LTR H.LT Org. Type Scale Contrsat OK Auto Normal Grossy Previous OK 2 Gray (Effective only when option is attached.) Previous OK O/D -1 +1 Previous OK Operation Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 74
) of the original to be scanned. A(Portrait) B(Landscape) B(Portrait) OK Qlty Org. Type B4 B3 B5 B4 B6 B5 Sets the scale for the image output. Scale Contrast OK OK Auto OK Normal Grossy Previous OK 2 Gray (Effective only when option is attached.) Previous OK * Select [OK] to - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 75
Pnl set Connect Reset Previous PC Printer Previous OK Set cfm Previous OK and activated for the current and subsequent operations. Auto clr Lamp off Save mode Previous 1 min. 3 min. 10 min for the current and subsequent operations. SCSI set ID number of the SCSI port is customized for the current - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 76
User Mode Press the User Mode key on the control panel. The User Mode menu is displayed. Contrast User Mode Job Recall Mode Check 5-20 Set User Choice Save Book Cent Out Prev Data Sheet Eras Put ious Operation Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 77
. 1 Select [Save Data] from the User Mode menu. The program registration screen appears. Set User Choice Save Book Cent Out Prev Data Sheet Eras Put ious Select [OK] to register the settings. Select [Confirm] to review the settings. Select [Previous] to return to the program registration screen. - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 78
. Refer to page 5-10 "Book/Sheet modes" for details. Select [Book/Sheet] from the User Mode menu. The book/sheet setting screen appears. Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious Select [Book mode] when scanning a thick original (books or dictionaries). Select [OK] to - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 79
User Mode Book mode setting function Normally, "Book mode" is used in "Auto" setting. In the following cases, however, set the distance between the stopper and the original. N A hardcover book is scanned N The original height cannot be detected (a waning message "Book 10) 0.0 mm Book Sheet -0.5 mm - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 80
adjusted to be within a range of 0 to 50 mm in 10 mm increments. The adjusted setting value appears on the display. 5-24 User Mode Set Thickness (~50) 20 mm Book Sheet -10 mm +10 mm mode mode OK Select [OK] to return to the main menu. NOTE When Sheet mode is selected - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 81
shadow generated in the center of the open book is removed. Spread mode Erasing width Single or Book Split mode Erasing width Operation Chapter 5 Select [Cent Eras] from the User Mode menu. The center eras setting screen appears. Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 82
The erasing width can be adjusted from 2.5 to 20 mm (0.1" to 0.8") in 2.5 mm (0.1") increments. The set value is displayed in the message area. Select [OK] to return to the main menu. 5-26 User Mode Set Width/Position 5.0 mm Auto Cent -2.5 mm +2.5 mm set set Wide Wide OK Operation Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 83
Mode Output Select the external device connected to the Scanner. Select [Output] from the User Mode menu. The output setting menu appears. Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious Select [PC] when a personal computer is connected. Select [OK] to return to the main menu - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 84
Exiting User Mode Select [Previous] from the User Mode menu. 5-28 User Mode Set User Choice Save Book Cent Out Prev Data Sheet Eras put ious Operation Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 85
Operation Chapter 5 5-29 Recalling jobs Recall programs registered using [Save Data]. 1 Press the Job Recall key on the control panel. Contrast User Mode Job Recall Mode Check 2 Select anyone of programs No. 1 to 3. The corresponding program is recalled and validated. Select [Previous] to - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 86
. This key can be used to check Contrast settings whenever necessary. User Mode Job Recall Mode Check Current settings are displayed. Select [Next]. MASK FINGER MASK CENTER ERASE ORIGINAL CONNECTION ON CENTERING OFF OFF OFF Book Auto Next PC Operation Chapter 5 Select [OK] to return to - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 87
functions Edit Functions Select [Edit] from the main menu to set editing functions for scanning. Start Appli./Driver A 600 A4 Edit Expo Reso Size 2 Qlty Center Erase (Cent Eras) The shadow generated in the center of the open book is erased during scanning. Spread mode Erasing width Single or - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 88
5-32 Using the edit functions Frame Masking (Masking) Objects outside the original are erased to prevent a shadowed (black) frame from being created on the output, i.e. when the selected paper is larger than the original. Frame Masking: OFF 1 2 1 2 Frame Masking: ON 1 2 NOTE • This function - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 89
5-33 Using the edit functions Finger Masking (Fing Mask) This function removes the image of the fingers holding the original from the scanned image. Finger Masking: OFF 1 2 1 2 Finger Masking: ON 1 2 NOTE Finger Masking may affect scanning depending on the density and colors of the original. - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 90
Finger Masking is available in the following 2 modes. 5-34 Using the edit functions Masking fingers only 1 2 1 2 Masking outer margins (Including fingers) 1 2 Default setting is "Masking fingers only." To change the setting, contact your authorized dealer. Operation Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 91
1 2 Centering: ON 1 2 Centering: OFF Spread mode 1 2 Single or Book 1 Split mode 2 1 2 NOTE This function is not effective when the center of the original is shifted 30 mm or more from the center of the book table. Select [Centerin]. The menu name is highlighted and the function is - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 92
5-36 Adjusting exposure for scanning Select [Expo] (exposure) from the main menu to set the exposure for scanning. Start Appli./Driver A 600 A4 2 Edit Expo Reso Size Qlty Operation Chapter 5 Auto The appropriate exposure is automatically selected according to the type of original. Select [ - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 93
adjustment The exposure for scanning is set manually. Select [Auto] to return the menu name to normal, indicating [Auto] is turned off. "A" disappears from the center of the exposure level bar. Set Exposure - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 94
Selecting resolution Select [Reso] from the main menu to set the resolution of the image output. 5-38 Start Appli./Driver A 600 A4 2 Edit Expo Reso Size Qlty Select [200 dpi], [300 dpi], [400 dpi], or [600 dpi]. The specified resolution is highlighted. Select [OK] to - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 95
5-39 Selecting scan size The size and direction (portrait or landscape) of the original on the book table are set. Scan size in inch 1 Select [Size] in the main menu. Start Appli./Driver A 600 LTR 2 Edit Expo Reso Size Qlty 2 Select original direction (landscape or portrait). Set Scan Size - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 96
NOTE • The resolution changes from [600 dpi] to [400 dpi] when [14x17], [11x17], [11x14] or [LGL] is selected. • The Scan mode changes from [Single] or [Book Split] to [Spread] when [17x14] is selected. Operation Chapter 5 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 97
in metric 1 Select [Size] from the main menu. Start Appli./Driver A 600 A4 2 Edit Expo Reso Size Qlty 2 Select the size ] to [400 dpi] when [A2] is selected. • The Scan mode changes from [Single] or [Book Split] to [Spread] when [A2] is selected. 3 When [A (Portrait)] is selected, the -2 size - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 98
to the main menu. NOTE • The resolution changes from [600 dpi] to [400 dpi] when [B3] is selected. • The Scan mode changes from [Single] or [Book Split] to [Spread] when [B3] or [B4] is selected. 3 When [B (Portrait)] is selected, the -4 size can be selected from B4, B5, and B6. The selected - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 99
Original Type 1 Select [Qlty] in the main menu. Start Appli./Driver A 600 A4 2 Edit Expo Reso Size Qlty 2 Select [Org. type]. The menu name is highlighted and the original type setting screen is displayed. Set Image Condition Org. Scale Cont type rast OK 3 Set the original type in the - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 100
key. Set Orginal Scale 2 Gray Prev ious OK Operation Chapter 5 2 (Binary) Gray (Grayscale) : Suitable to the text original. Read in a black and white image with high contrast. : Suitable to the photo original. Read in the image with 8-bit data. NOTE When the Book Scanner is not equipped with - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 101
Contrast 1 Select [Qlty] in the main menu. Start Appli./Driver A 600 A4 2 Edit Expo Reso Size Qlty 2 Select [Contrast]. The menu name is highlighted and the original type setting screen is displayed. Set Image Condition Org. Scale Cont type rast OK 3 Set the contrast on the Contrast - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 102
5-46 Selecting Contrast The following examples describe how to adjust the image read according to the standard settings (Highlight: 0, Shadow: 0, Exposure: Center) by correcting the contrast or adjusting the exposure: Image before adjusting the contrast To whiten the ground Image after adjusting - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 103
in Utility Mode: • Initial settings upon power supply • Timers (automatic clear, lamp off, and printer power save) • Warning (detection items and buzzer preferences) • Changing the SCSI port and ID No. Simultaneously press the User Mode key and the Job Recall key on the control Contrast panel - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 104
If any of the initial settings is changed, turn off the power to the Scanner. Then, turn it on, and the initial settings have been changed accordingly. Utility screen. The initial setting screen appears. Select Function Init Time Caut SCSI Main ial set ion set Menu 2 Select the desired item. The - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 105
Utility mode 3 Select [Connect] to set the connected -2 device for the current and subsequent operations. Select [PC] or [Printer] to connect the scanner to a personal computer or printer respectively. Select [Previous] to return to the previous screen. Select [OK] to define the device to which the - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 106
mode Time Set The settings for the timer (automatic clear time, lamp off time, and printer power save time) are set. 1 Select [Time set] on the main Utility screen. The timer setting screen appears. Select Function Init Time Caut SCSI Main ial set ion set Manu 2 Select the desired item. The - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 107
been pressed. Select [1 min.], [3 min.], or [5 min.] to set the desired lamp off time. Select [OK] to define the setting. 3 Select [Save mode] to set the time -3 until the printer enters Sleep mode after printing has been completed (printer power save time). Select [10 min.], [20 min.], or [30 min - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 108
defined here become effective immediately. 1 Select [Caution] on the main Utility screen. The warning setting screen appears. Select Function Init Time Caut SCSI Main ial set ion set Menu 2 Select the desired item. The selected menu name is highlighted. Select [Previous] to return to the main - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 109
Operation Chapter 5 5-53 Operations in Utility mode 3 Select [Buzzer] to set when the -2 buzzer goes off. Selecting [Alarm] makes the buzzer go off only when any warning message appears. Selecting [Stop] makes the buzzer go off when any prohibited operation is attempted, as well as when any warning - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 110
defined here are effective not only for the current operation but also when the Scanner is turned on next. 1 Select [SCSI set] on the main Utility screen. The SCSI setting screen appears. Select Function Init Time Caut SCSI Main ial set ion set Menu 2 Select [Up] or [Down] to change the ID - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 111
Operation Chapter 5 5-55 Operations in Utility mode Exiting Utility mode Select [Main Menu] on the main Utility screen. Select Function Init Time Caut SCSI Main ial set ion set Menu - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 112
Chapter 6 Troubleshooting Troubleshooting Chapter 6 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 113
problem. Warning message When any error occurs in parameters for auto focus, auto exposure, or paper size detection prior to scanning, a warning message appears on the display and the Scanner letter "C") and call your authorized dealer. Service Call Call Tech. Rep C15XX Troubleshooting Chapter 6 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 114
surface is within the range 65 mm above the book table. • Select Sheet mode. • The steel mirror is dirty. • Clean the steel mirror. • Light from the room lighting or the outside through windows reflects on the steel mirror. • Relocate the Scanner to a place where light from the room lighting or - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 115
left half of the book table. • Select [ lamp. • Current [Output] setting is [Printer] connection. • Change the [Output] setting to [PC]. • Communication Error • Check connection of SCSI cable and SCSI apparatus. • Turn the power switch OFF and then ON again to reset the system. Troubleshooting - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 116
Chapter 7 Maintenance Maintenance Chapter 7 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 117
checks 1. Any of the following conditions could damage the Scanner or other electrical equipment. Move the Scanner immediately and eliminate the possible cause of malfunction. • The Scanner is placed on the power cord or other cables. • The Scanner is placed on any cord of other electrical devices - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 118
Chapter 8 Specifications Specifications Chapter 8 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 119
correction: Text/Photo mode: Finger mask: Desk-top book scanner for face-up originals Rotary mirror scanning system Book, Sheet Max. 432 mm x 594 mm (Scanning 7500 pixels) Long cylindrical halogen lamp (DC150V, 620 W) Automatic (9 steps) or Manual (9 steps) Automatic or Manual (0-50 mm or 0-2") - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 120
erased Scanned image printed out in the center of the paper Spread / Single / Book Split 4.5 sec/page (A4, right page only, 400 dpi, AE, auto or less Video I/F (Printer), SCSI-2 (PC) Angle Book Holder, System Printer & PR Interface Kit, Foot Switch, Gray Scale Memory Board Specifications Chapter 8 - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 121
For Key Operator's Use When you need to call for service, the Key Operator should be prepared to provide the following Indication(s) on the Display. etc. For your reference purpose. Model Name PS7000 Serial No. Installation Data Authorized Dealer's Name TEL. No. Address Specifications Chapter - Konica Minolta PS7000 | PS7000 Operator Manual (PC Version) - Page 122
CO., LTD Printed in Japan The information contained in this manual is subject to change without notice to incorporate improvements made on the product or products the manual covers. MINOLTA CO., LTD. Image Information Products Marketing Headquarters 3-13, 2-chome, Azuchi-machi, Chuo-ku, Osaka
OperatorĀ“s Manual
PS7000
0818-7702-23
PC version