Kyocera ECOSYS FS-4100DN PRESCRIBE Commands Technical Reference Manual - Rev. - Page 102

Interface-dependent Parameters

Get Kyocera ECOSYS FS-4100DN PDF manuals and user guides View all Kyocera ECOSYS FS-4100DN manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Chapter 6 Permanent Parameters FRPO Parameters The FRPO command changes the value of one parameter in permanent memory. A separate command is required for each parameter change. The parameters, their meanings, and the specifiable values are listed below. In these tables, the Interface-dependent parameters affect the environment on the current interface only. Any changes made to the parameters on one interface will not change parameters on the other interfaces. To change a similar parameter on another interface, first switch to that interface then issue the FRPO command. The Interface-independent parameters affect all interfaces simultaneously. If the printing system is shared with other users, remember that changes made to non-interfacedependent parameters can affect users on other interfaces as well. Certain parameters are available only when the printing system is installed with the relevant option equipment. Note Interface-dependent Parameters Table 6.1. Interface-dependent Parameters (Sheet 1 of 3) Environment Top margina Left margina Page lengtha Page widtha Page orientationa Default font No.a Operation panel settings saving PCL font switch KC-GL optionsa Parameter A1 A2 A3 A4 A5 A6 A7 A8 C1 C5 C2 C3 C6 C8 G0 Value Factory setting Integer value in inches 0 Fraction value in 1/100 inches 0 Integer value in inches 0 Fraction value in 1/100 inches Integer value in inches Fraction value in 1/100 inches Integer value in inches Fraction value in 1/100 inches 0 13 (17)b 61 (30)b 13 (17)b 61 (30)b 0: Portrait, 1: Landscape 0 First two digits of power-up font 00 Middle two digits of power-up font 00 Last two digits of power-up font 00 0: Not saved at power-off 1 1: Saved at power-off 0: HP compatibility mode (Characters higher 0 than 127 are not printed.) 32: Conventional mode (Characters higher than 127 are printed. Supported symbol sets: ISO-60 Norway [00D], ISO-15 Italian [00I], ISO-11 Sweden [00S], ISO-6 ASCII [00U], ISO-4 U.K. [01E], ISO-69 France [01F], ISO-21 Germany [01G], ISO-17 Spain [02S], Symbol [19M]c) 0: Mode A; formfeed to SP0 0 1: Mode B; formfeed to SP0 2: Mode A; no formfeed to SP0 3: Mode B; no formfeed to SP0 4: Fixed mode A; formfeed 5: Fixed mode B; formfeed 6: Fixed mode A; no formfeed 7: Fixed mode B; no formfeed 8: Mode A; formfeed 9: Mode B; formfeed 10: Mode A; no formfeed 11: Mode B; no formfeed 12: Fixed mode A; formfeed 13: Fixed mode B; formfeed 14: Fixed mode A; no formfeed 15: Fixed mode B; no formfeed 6-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
Chapter 6 Permanent Parameters
6-2
FRPO Parameters
The FRPO command changes the value of one parameter in permanent memory. A
separate command is required for each parameter change. The parameters, their
meanings, and the specifiable values are listed below.
In these tables, the
Interface-dependent parameters
affect the environment on the current
interface only. Any changes made to the parameters on one interface will not change
parameters on the other interfaces. To change a similar parameter on another interface,
first switch to that interface then issue the FRPO command.
The
Interface-independent parameters
affect all interfaces simultaneously. If the printing
system is shared with other users, remember that changes made to non-interface-
dependent parameters can affect users on other interfaces as well.
Note
Certain parameters are available only when the printing system is installed with the rele-
vant option equipment.
Interface-dependent Parameters
Table 6.1.
Interface-dependent Parameters (Sheet 1 of 3)
Environment
Parameter
Value
Factory setting
Top margin
a
A1
Integer value in inches
0
A2
Fraction value in 1/100 inches
0
Left margin
a
A3
Integer value in inches
0
A4
Fraction value in 1/100 inches
0
Page length
a
A5
Integer value in inches
13 (17)
b
A6
Fraction value in 1/100 inches
61 (30)
b
Page width
a
A7
Integer value in inches
13 (17)
b
A8
Fraction value in 1/100 inches
61 (30)
b
Page orientation
a
C1
0: Portrait, 1: Landscape
0
Default font No.
a
C5
First two digits of power-up font
00
C2
Middle two digits of power-up font
00
C3
Last two digits of power-up font
00
Operation panel
settings saving
C6
0:
Not saved at power-off
1
1:
Saved at power-off
PCL font switch
C8
0:
HP compatibility mode (Characters higher
than 127 are not printed.)
0
32:
Conventional mode (Characters higher than
127 are printed. Supported symbol sets: ISO-60
Norway [00D], ISO-15 Italian [00I], ISO-11
Sweden [00S], ISO-6 ASCII [00U], ISO-4 U.K.
[01E], ISO-69 France [01F], ISO-21 Germany
[01G], ISO-17 Spain [02S], Symbol [19M]
c
)
KC-GL options
a
G0
0:
Mode A; formfeed to SP0
0
1:
Mode B; formfeed to SP0
2:
Mode A; no formfeed to SP0
3:
Mode B; no formfeed to SP0
4:
Fixed mode A; formfeed
5:
Fixed mode B; formfeed
6:
Fixed mode A; no formfeed
7:
Fixed mode B; no formfeed
8:
Mode A; formfeed
9:
Mode B; formfeed
10:
Mode A; no formfeed
11:
Mode B; no formfeed
12:
Fixed mode A; formfeed
13:
Fixed mode B; formfeed
14:
Fixed mode A; no formfeed
15:
Fixed mode B; no formfeed