Home » Kyocera Manuals » Printers » Kyocera ECOSYS FS-4100DN » Manual Viewer

Kyocera ECOSYS FS-4100DN PRESCRIBE Commands Technical Reference Manual - Rev. - Page 16

Character Spacing

View all Kyocera ECOSYS FS-4100DN manuals

Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Chapter 1 Introduction to PRESCRIBE cursor indicates where the next character will be printed or the next graphics will be drawn. (The printing system does not have separate cursors for text and graphics.) Text and graphics can be positioned at arbitrary locations on the page by moving the cursor with positioning commands (MAP, for example). Figure 1. 7. Text Positioning TITLE !R! BOX 1, 1; MRP 2, 1; EXIT; LABEL BOX 1, 1; Landscape Orientation Carriage Return MRP 2, 1; Space after EXIT; Cursor ends here Character Spacing Each character is printed within an individual cell as shown below. The character sits on a line called the baseline. Characters such as y descend below the base line. In some character fonts, all the character cells are the same size, so the number of character positions per inch is fixed. In other fonts, the size of character cells is proportional to the size of characters. These proportional fonts produce text that is easier to read. However, in order to align the right margin, you must use software that supports the printing system's proportional spacing. 1-8

Section	Page
General Infomation	3
Introduction	5
About the Technical Reference manual	6
Table of Contents	7
Introduction to PRESCRIBE	9
Format of PRESCRIBE Commands	12
Basic Concepts	12
Edge Limits	12
Margins	12
Page Orientation and Direction	13
Coordinate Systems	15
Text Positioning	15
Character Spacing	16
Paths	17
Logical Page and Physical Page	17
Command Parameters	18
Numeric Parameters	18
Character Strings	19
Upper and Lowercase Letters	20
Special Parameters	21
Graphics Tutorial	23
Drawing Lines	24
Drawing Boxes and Circles	28
Drawing Filled Shapes	31
Drawing Pie Charts	36
Path Mode Graphics	38
Path	38
Drawing Lines	40
Miter Limit	43
Dash Type	44
Drawing Arcs and Curves	46
Drawing Complex Curves	48
Closed Paths	51
Filled Areas	52
Clipping Rectangle	54
Printing with Character Paths	55
Raster Graphics	56
Raster Data Compression Formats	56
Commands for Printing Raster Data	57
Printing Raster Data	59
Changing the Printing System’s Imaging Model	59
Saving and Restoring the Graphics State	61
Macros	63
Examples of Macros	65
Fonts	69
List of Fonts	70
KPDL Fonts	72
Substituting a Bitmap Font	74
Font Selection	75
Font Selection by PRESCRIBE Commands	75
Placement of Font Commands	79
Creation of New Symbols and Characters	80
Symbol Set	81
International Characters	82
Selecting HP Symbol Sets	82
Barcodes	85
PDF417 Symbol Description	94
Printing a Two-dimensional Barcode	96
Limitations of Two-dimensional Barcode	97
Macro PDF417	98
Creating a Macro PDF 417 Representation	98
Permanent Parameters	101
Interface-dependent Parameters	102
Interface-independent Parameters	105
Emulation	113
Automatic emulation sensing	115
General Information on Emulation	115
Line Printer Emulation (Mode 0)	115
IBM Proprinter X24E Emulation (Mode 1)	116
IBM Proprinter X24E Control Codes	118
IBM Symbol Sets	121
Diablo 630 Emulation (Mode 2)	124
Diablo 630 Control Codes	126
Diablo 630 Symbol Sets	128
Epson LQ-850 Emulation (Mode 5)	133
EPSON LQ-850 Control Codes	136
LQ-850 Symbol Sets	138
HP LaserJet Emulation (Mode 6)	145
LaserJet Fonts	147
LaserJet Symbol Sets	149
Resource Protection	152
Switching the Print Resolution	154
HP LaserJet Reset State	155
LaserJet PJL	155
HP LaserJet Printer Commands - PCL	161
HP-GL/2 Context Printer Commands	176
PJL Syntax Comparison	178
LaserJet Symbol Sets	179
HP 7550A Emulation [KC-GL] (Mode 8)	208
Basic	208
KC-GL Environment Options	209
Plotter Status Information	214
Device-Control Instructions	218
Fonts and Symbol Sets in KC-GL	219
KC-GL Symbol Sets	220
KC-GL Limits	222
Summary of KC-GL Instructions	223
KPDL Operators	227
Communication with the Printing System	227
KPDL Summary	228
KPDL Error Messages	251
KPDL Printable Area	252
Index	255
Numerics	255
A	255
B	255
C	255
D	255
E	255
F	256
G	256
H	256
I	256
K	256
L	256
M	256
N	256
O	257
P	257
Q	257
R	257
S	257
T	257
U	257
W	257
X	257

Match case Limit results 1 per page

Chapter 1 Introduction to PRESCRIBE

1-8

cursor indicates where the next character will be printed or the next graphics will be

drawn. (The printing system does not have separate cursors for text and graphics.)

Text and graphics can be positioned at arbitrary locations on the page by moving the cur-

sor with positioning commands (MAP, for example).

Figure 1. 7.

Text Positioning

TITLE

!R! BOX 1, 1; MRP 2, 1;

EXIT; LABEL

Character Spacing

Each character is printed within an individual cell as shown below. The character sits on

a line called the

baseline

. Characters such as

descend below the base line

In some character fonts, all the character cells are the same size, so the number of charac-

ter positions per inch is fixed. In other fonts, the size of character cells is proportional to

the size of characters. These proportional fonts produce text that is easier to read. How-

ever, in order to align the right margin, you must use software that supports the printing

system’s proportional spacing.

Carriage Return

Space after EXIT;

Cursor ends here

MRP 2, 1;

BOX 1, 1;

Landscape Orientation