Kyocera FS-1320D PRESCRIBE Commands Command Reference Manual Rev 4.8
Kyocera FS-1320D Manual
UPC - 632983018194
View all Kyocera FS-1320D manuals
Add to My Manuals
Save this manual to your list of manuals |
Kyocera FS-1320D manual content summary:
- Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 1
PRESCRIBE Commands Command Reference - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 2
of Kyocera Mita Corporation is prohibited. Any copies made of all or part of this manual, instructions in this manual. No responsibility is assumed for defects in the printer's firmware. Regarding Tradenames: PRESCRIBE is a registered trademark of Kyocera Corporation. KPDL is a trademark of Kyocera - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 3
to the User's Manual. Helvetica, Palatino and printers. If you need to have access to the fonts on more than three printers free from defects in material and workmanship. Monotype Imaging does not warrant that the Software is free repair or replacement of defective parts, upon their return to Monotype - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 4
This page is left blank intentionally iv - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 5
Table of Contents Overview of PRESCRIBE Commands by Function 2 Access Commands 2 Print System Setting Commands 2 Margin and Page Portrait/Landscape Orientation Commands 3 Font Commands 4 Cursor Movement Commands 5 Vector Graphics Commands 5 Path Mode Graphics Commands 6 Raster Graphics - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 6
Relative Position specified by Angle 82 DUPX - select/deselect DUPleX mode 84 DXPG - select DupleX PaGe side 85 DZP - Draw to Zero-relative Position change current FONT 108 FPAT - generate Fill PATtern 110 FRPO - Firmware RePrOgram 112 FRPO INIT - FRPO-INITialize 114 FSET - change current - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 7
Paper SouRCe 213 PXPL - PiXel PLacement 214 !R! - PRESCRIBE start sequence 215 RCLT - Rotated CoLlaTion 217 RDMP - Received-data DuMP 218 RES - RESet 220 RESL - select RESoLution 222 RGBL - control RGB Level 223 RGST - offset ReGiSTration 225 RPCS - Return to Previous Code Set 226 RPF - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 8
Contents-iv RWRF R - [Read/Write Resource File] Read 256 RWRF T - [Read/Write Resource File] set Terminate string ---------- 257 RWRF W - [Read/Write Resource File] Write data to external device (API program) 258 RWRF W - [Read/Write Resource File] Write data to external device (font) ---- 259 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 9
PassWord 359 WIDE - set WIDE A4 mode 361 WRED - WRite EnD 362 XBAR - print two dimensional barcode 363 XBCP 0 - select barcode type/reset all other XBCP parameters---------- 365 XBCP 1 - specify narrowest element width 366 XBCP 2 - specify error correction level by percentage 367 XBCP 3 - set - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 10
Contents-vi - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 11
PRESCRIBE Command Reference - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 12
the printing system commands supported by the various models. Support for certain commands varies FDIR MP tray Feed DIRection 100 FRPO Firmware RePrOgram 112 FRPO INIT FRPO-INITialize 114 SouRCe 213 RCLT Rotated CoLlaTion 217 RES RESet 220 RESL select RESoLution 222 RGST offset - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 13
area is to use a large value such as 100 (centimeters). The margins and page orientation can be reset by using the RES command. Command Function Page SBM Set Bottom Margin 264 SLM Set Left Margin 307 SLPP are more fully explained in Section 1.3. of the Technical Reference manual. 3 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 14
's specific number. It is also possible to change the attributes of fonts and print them in a unique style. Additionally, there are commands to download fonts to the printing system from an external source, and to generate fonts. Command Function Page ALTB A [ALlocate TaBle] Assign user-defined - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 15
SFNT Select current FoNT by typeface 294 TPRS Text PaRSing 351 Fonts are more fully explained in Chapter 4 of the Technical Reference manual. Cursor Movement Commands These commands move the cursor to specific positions. Cursor movements can be established for absolute positions based on the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 16
fonts can be particularly taxing on printing system memory, producing unexpected print results. It may be possible to correct the problem by removing some of the downloaded fonts or by simplifying the graphic. To determine current memory usage, refer to a status page. Command Function Page ARC - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 17
332 STR SeT dot Resolution 343 Color Commands Color commands are used to create a color palette, assign colors to a palette, and specify colors. In this manual, color commands are marked with COLOR under the command name. 7 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 18
digits added. Command BARC ENDB XBAR XBCP XBUF Function draw BARCode END a two-dimensional Barcode string print two dimensional barcode select barcode type/reset all other XBCP parameters, etc. define a BUFfer name Page 34 91 363 365 to 387 391 Macro Commands A series of PRESCRIBE commands can - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 19
Overview of PRESCRIBE Commands by Function Command Function Page DAM Delete All Macros 72 DELM DELete Macro 76 EMCR Enable MaCRo depending on paper source 89 ENDC END carbon Copy 92 ENDM END Macro 94 MCRO define MaCRO 160 Debug Commands These commands can be used to check the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 20
in the hard disk by the JOBS command, it can be retrieved from the hard disk for printing with various printing features such as stapling, duplex-printing, mailboxing, etc., added on the fly. Command Function Page CDSK Check hard DiSK 49 JOBD JOB Deletion 132 JOBL print JOB List 134 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 21
by the STAT command or by pressing the panel keys. The User's Manual provides a full description of the control panel functions. Many PRESCRIBE commands can be embedded commands within word processing software. This support depends upon the emulation mode and the software. See Emulation of the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 22
PRESCRIBE Command Reference ACLI - Add CoLor by Index COLOR Format ACLI index, color1, color2, color3; Parameters index: integer from 1 to 255 color1: value for red, integer from 0 to 255, in RGB color space value for lightness, number from 0.0 to 100.0, in L*a*b color space color2: value - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 23
File !R! RES; DAM; UNIT C; SFNT 'AntiqueOlive-Bd', 20; CPAL C; SPAL 1; CID 0, 1; ACLI 1, 0, 0, 255; ACLI 2, 0, 255, 0; ACLI 3, 255, 0, 0; MZP 1, 1; SCOL 1; TEXT 'This line is printed in blue.'; MZP 1, 2.4; SCOL 2; TEXT 'This line is printed in green.'; MZP 1, 3.8; SCOL 3; TEXT 'This line is printed - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 24
PRESCRIBE Command Reference ALTB A - [ALlocate TaBle] Assign user-defined character table Format ALTB A, table-id; Parameter table-id: number identifying the character table assigned to the resident font, from 1 to 65535 Function The ALTB A command assigns the user-defined character table to - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 25
ALTB C ALTB C - [ALlocate TaBle] Convert character code Format ALTB C, table-id, source-character, target-character; Parameters table-id: number identifying the character table to convert the character, from 1 to 65535 source-character: character code before conversion: 1-byte code = 0 to 255; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 26
PRESCRIBE Command Reference ALTB D - [ALlocate TaBle] Delete user-defined character table Format ALTB D, table-id; Parameter table-id: number identifying the character table, from 1 to 65535, to be deleted Function The ALTB D command deletes the character table defined by the user. If the table - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 27
ALTB E ALTB E - [ALlocate TaBle] End defining combination characters Format ALTB E; Parameter None Function This command signals the end of defining combination characters in an already generated user-defined character table which was started by the ALTB S command. (page 20). The registered combined - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 28
PRESCRIBE Command Reference ALTB G - [ALlocate TaBle] Generate user-defined table Format ALTB G, table-id, table-format; Parameters table-id: table ID number: 1 to 65535 table-format: 1 = 1-byte, character codes 0 to 255 2 = 2-byte, character codes 0 to 65533 Function The ALTB G command - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 29
ALTB R ALTB R - [ALlocate TaBle] Release user-defined character table Format ALTB R, table-id; Parameter table-id: number identifying the character table to be released Function The ALTB R command terminates the assignment of the user-defined character table for the current resident font. It is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 30
PRESCRIBE Command Reference ALTB S - [ALlocate TaBle] Start to define the combination character Format ALTB S, table-id, code[, width, height[[, x-coordinate, y-coordinate, [paint-mode]]]; Parameters table-id: number identifying the character table to define the combination character, from 1 to - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 31
ALTB T ALTB T - [ALlocate TaBle] define combined character by Table Format ALTB T, character-code, width, height, x-coordinate, y-coordinate; Parameters code: character code for which the combined character is defined, or hexadecimal notation ($xxxx), JIS code width: character width: the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 32
PRESCRIBE Command Reference File !R! res; unit c; SFNT 'TimesNewRoman', 48; ALTB G, 1000, 1; ALTB A, 1000; ALTB S, 1000, 64, 1800, 1000; ALTB T, 77, 700, 700, 0, 700; CMNT M; ALTB T, 65, 700, 700, 630, 700; CMNT A; ALTB T, 85, 700, 700, 1050, 700; CMNT U; ALTB T, 73, 700, 700, 1570, 700; CMNT I; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 33
ALTF ALTF - change to ALTernate Font Format ALTF alternate-number; Parameter alternate-number: a number from 0 to 47 Function The ALTF command changes the current font to a font designated by an alternate number. The actual font assigned to this alternate number is set by a previous SETF - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 34
PRESCRIBE Command Reference File !R! RES; SFNT "Helvetica-Nr", 12, 1000; SFNT "TimesNewRoman-It", 11, 1001; SETF 1, 1000; SETF 2, 1001; MCRO BIBLIO; ALTF 1; TEXT %1, E; TEXT " ", E; ALTF 2; TEXT %2, E; TEXT " ", E; ALTF 1; TEXT %3, N; ENDM; ALTF 1; TEXT "Bibliography", N, U; TEXT, N; CALL BIBLIO, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 35
AMCR AMCR - call Automatic MaCRo Format AMCR mode, [repeat-count] macro-name, parameter, ...; Parameters mode: E = Enable automatic macro; Save and retain current printing parameters T = Enable automatic macro; Do not save current printing parameters D = Disable automatic macro repeat-count: - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 36
PRESCRIBE Command Reference File !R! RES; MCRO CROPMARK; UNIT C; MZP 2.46, 3.96; SCP; SCP; SCP; MRP -.635, 0; DRP -1.9, 0; RPP; MRP 0, -.635; DRP 0, -1.9; RPP; MRP 14.85, 0; SCP; SCP; MRP .635, 0; DRP 1.9, 0; RPP; MRP 0, -.635; DRP 0, -1.9; RPP; MRP 0, 21; SCP; SCP; MRP .635, 0; DRP 1.9, 0; RPP; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 37
paper of different paper sizes and types, printing will continue for the different paper sizes and types. If the automatic paper selection feature of the printer driver is used, APSG is disabled. To utilize paper source grouping, the paper source must be explicitly commanded by the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 38
PRESCRIBE Command Reference ARC - draw filled-in ARC Format ARC inner-radius, outer-radius, start-angle, end-angle; Parameters inner-radius: inner radius of arc outer-radius: outer radius of arc start-angle: starting angle end-angle: ending angle Function The ARC command works in the standard - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 39
ARC File !R! RES; UNIT C; MAP 5, 8; PAT 52; ARC 1, 2, -45, 45; MAP 5, 10; PIE 2, 0, 10, 20, 30; ARC 0, 2, 0, 60; PAT 20; ARC 0, 2, 60, 180; PAT 10; ARC 0, 2, 180, 360; PAT 1; NEWP; PMZP 4, 2; PARC 4, 3, 1, 90, 270; PARC 5, 4, 1, 180, 360; PARC 6, 3, 1, 270, 90; PARC 5, 2, 1, 0, 180; STRK; MRP 0.6, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 40
PRESCRIBE Command Reference Printout Related Command PARC 30 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 41
by the user to the current resident font. The external characters should be generated and downloaded in the printing system as an external font by using the LDFC or LDFN command. For the print systems supporting 2-byte font system, if the user-defined font is a 1-byte code font, it is assigned - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 42
group of trays. The maximum number of parameters must be equal to the number of the trays the sorter is equipped with. By the factory default, the trays are grouped as the following table: Group 1 2 3 4 5 Equiv. ASTK command SO-6 1, 2 3, 4 5, 6 7, 8 9 to 15 ASTK 2, 4, 6, 8; Sorter model SO-30 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 43
ASTK File The following command sequence delivers print jobs to trays 4, 5, 6, and 7 (the second group). !R! FRPO S0, 1; CMNT Enter multiple sorter mode; ASTK 3, 7, 9; CMNT Create three groups; MID 2; CMNT Send the output to 2nd grp.; SSTK; CMNT Sort; EXIT; Related Commands CSTK, MID, MSTK, SSTK 33 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 44
with mod-43 check digit 21 = Interleaved two of five with no check digit 22 =Identicon two of five with no checksum 23 = Code 128 (manual mode change) 24 = Code 128 (auto mode change) 25 = Code 11 with only 'c' 26 = Code 11 with both 'c' and 'k' checksum 27 = Code 93 with both - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 45
varies depending on the type of barcode to use. Characters that can be used for the most barcode type are described in the table below. 1 FS-600/FS-7000/FS-9100/FS-9500 only 35 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 46
PRESCRIBE Command Reference Table 20 Characters that can be used Type Max Characters to be used Default 0 11 0123456789 0 1 13 0123456789 0 2 16 0123456789 0 3 13 0123456789 0 4 18 0123456789 0 5 22 0123456789 0 6 25 0123456789 0 7 29 0123456789 0 8 6 0123456789 0 9 8 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 47
BARC Type Max Characters to be used 40 1 The following FIM pattern type A. Country Reply Mail with POSTNET B. Business Reply, Penalty and Franked Mail without POSTNET C. Business Reply, Penalty and Franked Mail with POSTNET D. OCR Readable Mail without POSTNET 41 125 0123456789 42 80 All (ASCII - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 48
SPSZ 8, 5;. For details on page size, refer to the SPSZ command page in this manual. The document must have the same page size for all pages. If the double size BKLT command and prints in the original paper size. Duplex printing is also possible by adding the DUPX command. To correctly arrange two neighboring - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 49
BKLT binding = 1, reading pages from left to right File binding = 2, reading pages from right to left This command is not supported by some photocopier models. The following command sequence prints a copy of a 12-page A4 document in booklet mode, folding the stack in the middle. The - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 50
PRESCRIBE Command Reference BLK - draw filled-in BLocK Format BLK width, depth[, option]; Parameters width: width of the block depth: depth of the block option: B = Leave the cursor unmoved (Default) H = Move the cursor to the horizontally adjacent corner V = Move the cursor to the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 51
BLK File !R! RES; UNIT C; MAP 5, 5; PAT 20; BOX 4, 1; BLK 4, 1; MRP 0, 1.5; BOX 4, 1; BLK 4, 1; MRP .9, .6; SFNT "Helvetica-Nr"; TEXT 'OVERPRINTING'; MRP 0, 5; PAT 29; BOX 1, -4; BLK 1, -4, H; PAT 39; BOX 1, -3; BLK 1, -3, H; PAT 49; BOX 1, -2; BLK 1, -2, H; PAT 59; BOX 1, -1; BLK 1, -1, H; PAGE; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 52
PRESCRIBE Command Reference BOX - draw BOX Format BOX width, depth[, option]; Parameters width: width of the box depth: depth of the box option: B = Leave the cursor unmoved (Default) H = Move the cursor to the horizontally adjacent corner V = Move the cursor to the vertically adjacent - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 53
BOX MAP 4, 0; SCP; SFNT "Helvetica-Nr", 10; BOX 4, 2, L; TEXT 'Text printed with option L'; RPP; BOX 4, 2, N; TEXT 'Text printed with option N'; PAGE; EXIT; Printout 43 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 54
PRESCRIBE Command Reference CALL - CALL macro Format CALL[ repeat-count] macro-name, parameter-value, ...; Parameters repeat-count: number of times the macro is to be executed macro-name: name defined by a MCRO command parameter-values: values given to the dummy parameters in the macro - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 55
File !R! RES; UNIT C; SLS .5; CMNT Requires BX and SCREEN macros; CMNT See ENDM command page; MAP 9, 3; CALL BX; MAP 7, 4; CALL 5 BX; MAP 5, 5; CALL 9 BX; MAP 8, 6; CALL SCREEN, 2.2, 1.7; MAP 8.6, 7; TEXT 'Narrow', L; TEXT 'screen'; MAP 5,9; CALL SCREEN, 8.2,1.2; MAP 8,10; TEXT 'Wide screen'; PAGE; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 56
; TERM; TERM; PSRC 4; AMCR E, COLOPHON; TERM; ENDC; In the example above, the second page is printed using cassette #2 with no form overlay. In carbon copy, duplex printing is not possible. The paper size and the page orientation should be consistent for all pages in the document to be carbon copied - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 57
CCPY File !R! RES; DAM; CCPY D; UNIT C; MCRO COVER; UNIT C; SFNT 'Helvetica-Bd',14; TEXT 'Registration Form', L; SFNT 'Helvetica', 9; TEXT 'Please provide your personal details:'; MRP 0, .2; BOX 6, 1; MRP 0, .35; TEXT ' Your Name'; ENDM; MCRO MAIL; UNIT C; SFNT 'Helvetica-Bd',14; TEXT 'Mailing - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 58
PRESCRIBE Command Reference Printout 48 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 59
CDSK CDSK - Check hard DiSK Format CDSK; Parameter None Function The CDSK command verifies data in the hard disk (garbage collection). It deletes garbage jobs such as page image data that were accidentally generated in the hard disk and normally inaccessible for deletion. File !R! CDSK; EXIT; 49 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 60
PRESCRIBE Command Reference CID - Configure color-Image Data COLOR Format CID color-space, encoding; Parameters color-space: 0 = Device-dependent RGB (Default) 1 = Device-dependent CMY 2 = Void 3 = CIE L*a*b encoding: Pixel encoding 1 = Indexed by Pixel (Default) 3 = Direct by Pixel Function - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 61
CID File !R! RES; DAM; UNIT C; SFNT 'Helvetica-Bd', 20; CPAL C, 1; SPAL 1; CID 0, 1; CMNT RGB Color Space used; ACLI 1, 0, 0, 255; MZP 1, 1; SCOL 1; TEXT 'An RGB color palette is used.' CID 3, 1; CMNT L*a*b Color Space used; ACLI 2, 100, 75, 0; MZP 1, 2; SCOL 2; TEXT 'An L*a*b color palette is used - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 62
PRESCRIBE Command Reference CIR - draw CIRcle Format CIR radius; Parameter radius: radius of the circle Function In standard graphics mode, the CIR command draws a circle centered at the current cursor position. The line thickness used is designated by the SPD command. A circle can also be - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 63
CIR Printout 53 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 64
PRESCRIBE Command Reference CLIP - CLIP current path Format CLIP [clip-mode]; Parameter clip-mode: 1: EO clip 2: Non-zero winding clip Function The CLIP command sets the current path as the clipped path. After this command is issued, no painting is done outside the area of the path. Executing - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 65
bottom-left corner [greater values for (x1, y1) than for (x2, y2)], the printing system exchanges the coordinate values with each other. The printing system resets the size of the rectangular clipping path to be equal to the maximum printable area of the current page size when a PSRC, RES, SPO, or - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 66
PRESCRIBE Command Reference File !R! RES; UNIT C; NEWP; SPD 1; PMRA 6, 9, 3, 0; PAT 1; PARC 6, 9, 3, 0, 360; CLPR 3, 6, 9, 12; STRK; PAGE; EXIT; Printout 56 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 67
CLSP CLSP - CLoSe Path Format CLSP; Parameter None Function The CLSP command closes an open path by adding a line segment extending from the end of the path to the beginning of the path. Simply ending a path at the path's starting point does not make it a closed path; such a path remains open until - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 68
PRESCRIBE Command Reference Printout Related Command NEWP 58 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 69
CMNT CMNT - CoMmeNT Format CMNT string; Parameter string: any character string Function The CMNT command adds a character string, typically a comment explaining the purpose of the following PRESCRIBE commands. The CMNT command statement will be ignored by the printing system. Although character - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 70
PRESCRIBE Command Reference CMOD - Color MODe COLOR Format CMOD mode; Parameter mode: color mode: 0 = Monochrome 1 = Color (Default) Function The CMOD command switches between monochrome and color modes. In monochrome mode, other color commands are still enabled, but printing is converted to - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 71
copies for each page in a print job. This copy count value can be changed by sending the printing system another COPY command or by issuing a reset command. For best results, place the copy command near the start of a job or at the top of a page. If two or more copy commands - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 72
PRESCRIBE Command Reference Printout 62 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 73
applied to palette of ID 0. No check is made whether the palette ID number given already exists for another palette. The palette ID number is reset to 0 by RES command. Mode A deletes all existing palettes and brings the default palette back to the default state (ID 0). Note that non-active palettes - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 74
PRESCRIBE Command Reference CPTH - Character PaTH Format CPTH 'string'; Parameter string: any character string except from ASCII code 31 (hex 1F) and lower Function The CPTH command constructs a path which adds the outlines of characters to the current path. When stroked or filled, it prints - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 75
3R = PC Cyrillic* 3S = ISO 10 Swedish 4S = ISO 16 Portuguese 4U = Roman-9 5M = PS Math 5N = ISO Latin 5 5S = ISO 84 Portuguese 5T = ISO Windows Latin 5 6J = MS Publishing 6M = Ventura Math 6N = ISO8859/10 Latin 6 6S = ISO 85 Spanish 7J = Desktop 8G = Greek-8 8M = Math 8 8Q = PC Set 1 IBM - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 76
14R = PC Ukrainian 15U = Pi Font 16U = PC-857 17U = PC 852 18N = ISO-10646 18U = PC-853 Turkish/Latin 3 19L = Windows 3.1 Baltic† 19M = Symbol (Symbol-Set-SWM font only) 19U = Windows Latin 1 20U = PC-860 Portugal† 21U = PC-861 Iceland† 23U = PC-863 Canada-French† 24Q = PC-8 Polish Mazovia† 25U = PC - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 77
a specific group of alphabetic, numeric, and symbolic characters. The CSET command summons the symbol set to suit the various languages with the current font. The factory default symbol set is 0U (US ASCII). When the FSET command is used to select a font, the printing system selects a font based on - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 78
: number from 1 to the maximum (bottom) Function The CSTK command is effective only when the optional sorter is installed to the printing system. It instructs the printing system to deliver printed pages to the sorter in the collator mode. Each tray specified receives all copies of one page. The - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 79
CTXT CTXT - print Centered TeXT Format CTXT [,string][,option][,U-option]; Parameters string: any character string option: B = Leave cursor at center of string E = Move cursor at end of string L = Move cursor down one line N = Move cursor to beginning of next line U-option: Underline text - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 80
PRESCRIBE Command Reference Printout 70 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 81
DAF DAF - Delete All Fonts Format DAF; Parameter None Function The DAF command deletes all nonresident fonts and the font numbers assigned to scalable fonts by the SFNT command from the printing system's memory. This enables the user to make room for new fonts, macros, and graphics. File !R! UNIT P; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 82
PRESCRIBE Command Reference DAM - Delete All Macros Format DAM; Parameter None Function The DAM command deletes all macro definitions made by using the PRESCRIBE MCRO command from the printing system's memory. This enables the user to make room for new macros, fonts, or graphics. File !R! RES; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 83
DAP DAP - Draw to Absolute Position Format DAP x-coordinate, y-coordinate; Parameters x-coordinate: distance from the left margin y-coordinate: distance from the top margin Function The DAP command draws a line from the current cursor position to a position specified relative to the top and - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 84
PRESCRIBE Command Reference Printout 74 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 85
DELF DELF - DELete Font Format DELF font-number; Parameter font-number: number identifying the font to be deleted Function The DELF command deletes any designated non-resident font from the printing system's memory. This enables the user to make room for new fonts, macros, and graphics. The - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 86
PRESCRIBE Command Reference DELM - DELete Macro Format DELM macro-name; Parameter macro-name: name defined by a previous MCRO command Function The DELM command deletes a specified macro definition from the printing system's memory to make room for new macros, fonts, or graphics, or so that the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 87
File !R! UNIT C; MCRO BX; SPD .05; BOX .8, -.8; MRP 1, 0; ENDM; MCRO SCREEN %, width, depth; CMNT Draws box with rounded corners; CMNT Leaves cursor at previous position; SPD .08; SCP; MRP .25, .25; ARC .23, .30, 270, 0; MRP 0, -.25; DRP %1, 0; MRP 0, .25; ARC .23, .30, 0, 90; MRP .27, 0; DRP 0, %2; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 88
PRESCRIBE Command Reference DPAT - select Dashed PATtern Format DPAT number; Parameter number: number from 1 to 20 (11 to 20 are for user-defined patterns.) Function The DPAT command specifies the pattern of alternating black and white dashes to stroke the current path. The resident patterns - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 89
DPAT Printout Related Command SDP 79 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 90
PRESCRIBE Command Reference DRP - Draw to Relative Position Format DRP x-coordinate, y-coordinate, ...; Parameter x-coordinate/y-coordinate: coordinates as measured from the current cursor position Function The DRP command draws a line from the current cursor position to a specified relative - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 91
DRP Printout Related Command PDRP 81 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 92
PRESCRIBE Command Reference DRPA - Draw to Relative Position specified by Angle Format DRPA length, angle; Parameters length: length of the line angle: angle in degrees, measured clockwise from the vertical Function The DRPA command draws a line of a specified length at a specified angle, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 93
DRPA Printout 83 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 94
mode, short-edge binding Function The DUPX command is effective only when the option duplexer is installed to the printing system. It instructs the printing system to select or deselect duplex printing and sets the binding mode. Portrait, long-edge Portrait, short-edge Landscape, long-edge - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 95
0 = Select next side (the same as form feed) 1 = Select front side 2 = Select back side Function The DXPG command is effective only when the option duplexer is installed to the printing system. It ends printing on the current page in the same manner as a form feed. However, unlike the form feed, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 96
printing on both sides of the page. !R! CMNT Initiates a PRESCRIBE command sequence; RES; CMNT Causes a page break and resets parameters; DUPX 2; CMNT Selects duplex mode, short-edge binding; SPO P; CMNT Selects portrait orientation; STAK 1; CMNT Select face-down delivery; EXIT; This text prints - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 97
DZP DZP - Draw to Zero-relative Position Format DZP x-coordinate, y-coordinate; Parameters x-coordinate: distance from the left edge limit of paper y-coordinate: distance from the top edge limit of paper Function The DZP command draws a line from the current cursor position to a position - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 98
PRESCRIBE Command Reference Printout Related Command PDZP 88 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 99
cassette 3 4 = cassette 4 5 = cassette 5 6 = cassette 6 (bottom) 99 = envelope or universal feeder print-side: side of the page the macro is executed when duplex-printing 0 = front 1 = back repeat-count: number of times the macro is executed macro-name: name defined by the MCRO command parameter - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 100
PRESCRIBE Command Reference Function The EMCR command allows separate auto macros to be assigned for each of the separate paper sources. In duplex printing, it is also possible to assign separate auto macros for both the front and back sides of a page. The following commands are invalid within a - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 101
18 is executed, it is used alone, without association with XBAR or XBUF. For details on two-dimensional barcodes, see Section 5.2. of the Technical Reference manual. 91 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 102
PRESCRIBE Command Reference ENDC - END carbon Copy Format ENDC; Function The ENDC command ends definition of the CCPY E command sequence. For details, refer to the CCPY command. 92 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 103
ENDD ENDD - END Dump Format ENDD; Parameter None Function The ENDD command ends a hexadecimal dump initiated by the RDMP (Received-data DuMP) command and returns to the PRESCRIBE command mode. File See RDMP on page 218. Related Command RDMP 93 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 104
PRESCRIBE Command Reference ENDM - END Macro Format ENDM; Parameter None Function The ENDM command ends a macro definition and returns to the PRESCRIBE command mode. File !R! RES; DAM; UNIT C; MCRO BX; SPD .05; BOX .8, -.8; MRP 1, 0; ENDM; MCRO SCREEN %, width, depth; CMNT Draws box with - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 105
Printout ENDM Related Commands CALL, DAM, DELM, MCRO 95 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 106
PRESCRIBE Command Reference ENDR - END Raster data Format ENDR; Parameter None Function The ENDR command declares the end of raster data. To declare the start of raster data, a RVRD command is used. File The following example prints an illustrated crown using the RVRD and ENDR. !R! RES; DAM; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 107
ENDR 5, 0, 160, 96, 80, 0; 5, 1, 24, 1, 136, 0; 5, 14, 134, 6, 23, 0; 5, 48, 65, 248, 32, 192; 5, 192, 129, 8, 16, 48; 5, 0, 64, 144, 32, 0; 5, 0, 32, 96, 64, 0; 5, 0, 16, 0, 128, 0; 5, 0, 32, 0, 64, 0; 5, 0, 16, 0, 128, 0; 5, 0, 8, 1, 0, 0; 5, 0, 6, 6, 0, 0; 5, 0, 1, 104, 0, 0; 5, 0, 0, 144, 0, 0; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 108
switches the Ecoprint on or off (default). Ecoprint is a standard feature of the print systems that enables the user to reduce the amount of toner placed on the page which saves on printing costs. With EPL 2;, the printing image appears lighter, yet remains readable. The following example simulates - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 109
EXIT EXIT - EXIT from PRESCRIBE mode Format EXIT [, E]; Parameter None Function When the printing system receives the EXIT command, it exits from the PRESCRIBE mode and treats the following information as characters to be printed. If the parameter E is added (EXIT, E;), the printing system ignores - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 110
or B5 size although this depends on the printing system model. This command is enabled only when the MP tray's operational mode is cassette or manual feed. Printing on A4 and letter size paper can only be done widthwise in first mode. This command causes a page break. This command is irrelevant - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 111
zero, the point is deemed to be outside; otherwise the point is deemed to be inside the path. The way in which several filled-in parts are stacked with each other to produce transparent and opaque effects is controlled by the SIMG (Set IMaGe model) command. Related Commands FPAT, GPAT, PAT - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 112
PRESCRIBE Command Reference File !R! RES; UNIT C; SIMG 1; CMNT Drawing clusters; NEWP; PMZP 10, 12; PDRP -5.7, -1.75; PCRP 0, 0, 0, -3.4, 3.1, -3.6; CLSP; PAT 2; FILL; PMZP 10, 12; PDRP -2.6, -5.35; PCRP 0, 0, 2.5, -2.5, 4.9, .1; CLSP; PAT 3; FILL; PMZP 10, 12; PDRP 5.7, -1.75; PCRP 0, 0, 0, -3.5, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 113
FILL Printout 103 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 114
computation. The number actually specifies the maximum error tolerance of a straight line segment approximation of any portion of the curve. The printing system resets the flatness to 1 when it receives the RES command. File !R! RES; FRPO N8,0; CMNT 300 dpi; UNIT C; SPD 0.02; NEWP; CMNT 1st circle - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 115
or bitmap, font selection sequence using FSET, font ID, etc. The resident fonts are identified by the letter I (internal) in the font ID; the downloaded fonts are identified by the letter M or D depending on whether the font is stored in the memory card or the hard disk, respectively. The font - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 116
PRESCRIBE Command Reference Sample of Font List Internal Scalable and Bitmapped Fonts List PRESCRIBE Font Name Scalable/Bitmap Password Selection [FSET] Font ID 106 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 117
FOLD FOLD - FOLD printed pages Format FOLD [staple]; Parameter staple: 1 = stapling Function The FOLD command is effective only when the optional document finisher having the booklet stitcher is installed to the printing system. This command is most conveniently used with the BKLT command that - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 118
font-number should designate a resident bitmap font, a scalable font selected by the SFNT command, or a nonresident font generated by the LDFC command or downloaded from the computer. If an undefined font-number is specified, the font will not change. To print a font list, use the FLST command. For - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 119
Printout Related Commands ALTF, FLST, SETF FONT 109 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 120
+16+8+4 = 60, and so on. For printing system models that support 600/1200 dpi resolution printing, the default resolution generated by the FPAT selected using the FRPO B8 command. See Section 6.2. of the Technical Reference manual (FRPO B8). The printing system recognizes a dot in the pattern as - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 121
File !R! RES; DAM; UNIT C; FSET 1p08V0s0b5T; MCRO PATTERN; FPAT %1, %2, %3, %4, %5, %6, %7, %8; BOX 5, 1; BLK 5, 1; MRP 0, 1.55; TEXT 'FPAT %1, %2, %3, %4, %5, %6, %7, %8;', L; ENDM; MAP 2, 2; SCP; CALL PATTERN, 3, 3, 0, 0, 0, 0, 0, 0; CALL PATTERN, 255, 0, 0, 0, 0, 0, 0, 0; CALL PATTERN, 1, 1, 1, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 122
- Firmware RePrOgram and their values are given in Chapter 6 of the Technical Reference manual. The FRPO command should be used only when it is necessary to can be reset to the factory-set values by the FRPO INIT (FRPO-INITialize) command. Note that the RES command does not reset those changes - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 123
Printout Related Command FRPO INIT FRPO 113 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 124
parameters. For a list of the factory default values, see Chapter 6 of the Technical Reference manual. The FRPO INIT command causes a page break. To activate the changes made with the FRPO INIT command, turn the printer power off then on again or reset the printer using the control panel keys. File - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 125
FSET FSET - change current Font SETting by characteristic Format FSET spacing-pitch-height-style-weight-typeface; Parameters spacing: fixed or proportional spacing, followed by a terminator P: 0 = fixed font 1 = proportional font pitch: pitch in cpi, from 0.44 to 99.99 cpi (ignored in a - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 126
at the end of this section demonstrates this function. Font selection is made based on the characteristics of the font, the font's location in the printer, and the font's orientation. In the list below, the characteristics of font are listed in order of priority, from highest to lowest: Symbol set - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 127
. It first examines all fonts to match based on symbol set (the highest priority). All matches are next examined based on spacing. When the printer has reduced the matches to one font, it selects that font. Bitmap fonts have priority over scalable fonts. FSET enables the user to select a general - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 128
PRESCRIBE Command Reference File !R! UNIT P; SFNT 'Swiss742SWC-Roman', 10; SLS 12; EXIT; First, this line is printed in a 10 point Swiss742SWC-Roman font. !R! FSET 14V; SLS 16; EXIT, E; Let's see if the height parameter is changed to 14 points by FSET 14V;. !R! FSET 1s3B; EXIT,E; Now this line - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 129
changes the designated attributes to the values of the new font. The default value of the FTMD command depends on the emulation mode. The printer does not automatically change any attributes not designated by the FTMD command. If necessary, these attributes must be adjusted by other commands: SCS or - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 130
Yes Portrait or landscape Yes Yes Yes Yes Yes Default Font Modes Emulation mode 0 (Line Printer) 1 (IBM X-24E) or 2 (Diablo 630) 5 (Epson LQ-850) 6 (HP LaserJet) 8 (KC-GL) Font mode 15 0 Printer's action when font is changed Adjusts page orientation, character spacing, line spacing. Does not - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 131
Printout FTMD 121 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 132
1200 dpi resolution. For printer models that support 600/1200 dpi resolution printing, the default resolution generated by the GPAT command is 300 dpi; however, 600/1200 dpi can be selected using the FRPO B8 command. See Section 6.2. of the Technical Reference manual - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 133
GPAT Printout Related Commands FPAT, PAT 123 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 134
processing images, the corresponding area can be represented by using either the same quantity of toner or only K toner for each of CMY. (If C = M = Y, the color is black in so on.) The graying process defaults to representation using K toner alone. However, a toggle switch is provided since, as - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 135
GRRD GRRD - GRaphic data ReaD COLOR Format GRRD format, width, height; ;ENDG; Parameters format: image format: B = Bitmap J = JPEG T = TIFF width: number from 0 to 65535 height: number from 0 to 65535 image: file name based on a specified format Function The GRRD command allows the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 136
PRESCRIBE Command Reference c:¥> echo !R! STR 300; MZP 1,1; GRRD J,0,0; > lpt1 c:¥> copy /b fluit.jpg lpt1 c:¥> echo ;ENDG; PAGE; EXIT; > lpt1 Printout 126 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 137
HUE HUE - adjust HUE COLOR Format HUE color, angle[, type]; Parameters color: number representing the color for hue adjustment: 0 = all colors 1 = R 2 = Y 3 = G 4 = C 5 = B 6 = M angle: angle of hue rotation in degrees: color = 0, - 180 to 180 (default = 0) color = 1 - 6, -10 to 10 (default - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 138
beyond their next hues. R Y G C B M If this command is issued to rotate a particular hue when all hues are rotated, the hues are controlled after they are reset to their default state. The HUE command is enabled for all color spaces, all color modes and all monitor simulation modes. If - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 139
of the available symbol sets are displayed in Emulation of the Technical Reference manual, emulation by emulation. Depending on the current emulation, the printer selects one of the symbol sets of the emulated printer appropriate for the country as requested by the country-code value. For example - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 140
. The factory setting is 0. Symbol Sets Available with INTL Country-code 0 (Epson) Code-set (emulation) 1 (HP LaserJet)a 2 (Daisywheel) 4 (IBM/Line Printer) 0b symbol set. (Default is US ASCII). It does not fully support all of the HP LaserJet symbol sets. To use one of the HP - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 141
INTL File !R! CMNT This file will not print correctly in the IBM; CMNT emulation (mode 1); RES; INTL 2, 2; SLM 1; STM 2; SFNT "Helvetica", 14; EXIT; Diese [pfel sind eine ]berraschung! !R! PAGE; EXIT; Printout 131 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 142
by mailbox-id 9 = Deletes the virtual mailbox specified by mailbox-id 15 = Resets all virtual mailboxes to a clean state job-id or mailbox-id: an integer jobs stored in the hard disk. This command may be used to make more free space in the hard disk by deleting unnecessary jobs. Modes 1 and 2 delete - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 143
JOBD Files To delete the temporary job with an ID of 28L016T50 from the hard disk: !R! JOBD 1, "28L016T50"; EXIT; To delete all permanent jobs in the hard disk: !R! JOBD 2; EXIT; To delete all temporary and permanent jobs in the hard disk: !R! JOBD; EXIT; To delete the jobs stacked in virtual - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 144
PRESCRIBE Command Reference JOBL - print JOB List Format JOBL mode; Parameter mode: 1 = prints a list of temporary jobs in the hard disk 2 = prints a list of permanent jobs in the hard disk 8 = prints a list of virtual mailboxes to represent their usage status Function The JOBL command prints a - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 145
File To print a permanent job list: !R! JOBL 2; EXIT; JOBL 135 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 146
PRESCRIBE Command Reference JOBO - JOB Output Format JOBO mode, 'job-id' or 'mailbox-id'[, password]; Parameters mode: 0 = normal 8 = virtual mailbox job-id (mode 0): job ID or page ID mailbox-id (mode 8): mailbox ID from 1 to 255, or alias password (mode 8 only): password for the mailbox - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 147
JOBO Files All jobs are delivered to the current output stack (all jobs to the same stack). Note however the jobs with stapling enabled will be forcibly sent to the stapler. The master password, if set previously by VMPW, is valid for all virtual mailboxes for which a password is set. An error - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 148
as indicated in the table below printoption 0 1 2 3 4 5 6 7 8 9 10 11 Function Parameter Effective to: Copy count Printing barcode Duplex printing Destination stack Stapling Barcode position Staple count Center stitch Punching Transparency separator Source for transparency separator Rotated - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 149
are valid only when the JOBP command follows the JOBO command to print the job. For example, the JOBP command sequence JOBP 2, 1; will not activate duplex printing if the preceding job to print was assigned by JOBS. A JOBP command sequence is cancelled if the host interface of the printing system is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 150
PRESCRIBE Command Reference JOBS - JOB Start Format JOBS save-mode, copy, barcode, barcode-position[, share, 'job-name', 'user-name', 'time']; Parameters save-mode: save mode: 0 = electronic sorting only 1 = temporary 2 = permanent 8 = (Print to) virtual mailbox copy: number of copies to - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 151
mailbox becomes valid. When no virtual mailbox corresponds to the alias given, the message display shows 'hard disk error 85 (see the Technical Reference manual.)' and information regarding the job which was thrown away is displayed in the error log. If JOBS-JOBT pairs are nested or if they are - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 152
are being stacked on virtual mailboxes (when the VMB-compatible printer driver is being used) will be displayed on the message display To stack the jobs between JOBS and JOBT on the virtual mailbox named Sales. !R! JOBS 8, 3, 'Sales', 0, 0, 'Invoice', 'Sales', '01/14/02 16:30:25'; UNIT C; MZP 5, 10; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 153
JOBS !R! JOBS 8, 3, 3, 15, 0, 'Service', 'Repair', '01/14/02 16:30:25'; UNIT C; MZP 5, 10; BOX 6, 6; PAGE; TEXT 'ABCDE'; PAGE; TEXT 'Domestic'; PAGE; JOBT; EXIT; 143 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 154
PRESCRIBE Command Reference JOBT - JOB Terminate Format JOBT; Parameter None Function The JOBT command terminates defining a job which is started by JOBS. The JOBT command is used in combination with JOBS to constitute a job definition. The printing system prints the job in the number of copies - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 155
until another JOG command is issued. This is unaffected even by the reception of a command such as RES, FRPO and SEM which results in a reset of the printer. When JOG is issued with a job defined by JOBS and JOBT, jogging affects the individual job (in the similar way as PJL). Therefore, JOG - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 156
T command. When storing a new PRESCRIBE command, if the specified command name has already been stored, the sending data will be invalid. Data downloaded with the LAPI command will be deleted (invalid) upon the system restart. Example: !R! LAPI "PRE" , "XXXX" , "XXXXXXXX" ;[Program Data]WRED; EXIT - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 157
LDFC LDFC - LoaD Font Character Format LDFC font-number, code, height, width, y-offset, x-offset, cell-width, center, rotation[, resolution]; bit-map; Parameters font-number: font number (integer from 1000 to 65535). Same for all characters in the font. Must not duplicate any resident bitmap - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 158
and another example appear in Chapter 4 of the Technical Reference manual. The resolution is valid only on a 600/1200 dpi printer model. File !R! LDFC 1000, 43, 39, 29, 1216, 0, 1216, 608, 0; @@2@@0@@2@@0@@2@@0@@2@@0@@7@@0@@7@@0@@7@@0@@?'@0 @@?'@0@A?p@0@A?p@0@C?x@0@G?|@0@O?~@0@_?/@0@/?/'0 A/?/p0G - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 159
LDFN C LDFN C - generate bitmap character for LoaDing FoNt Format LDFN C, font-number, code, height, width, y-offset, x-offset, cell-width; bit-map; Parameters font-number: font number (integer from 1000 to 65535) code: ASCII code of the character code (0 to 255 for European; 0 to 65533 for - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 160
The bitmap data transferred at the end of this command is transferred under Kyocera's original BBN format. This is the transfer format used by the LDFC and LDKC commands. This command is recommended for use with downloading bitmap fonts. In other words, this command is intended as an equivalent for - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 161
LDFN F LDFN F - create header for LoaDing FoNt Format LDFN F, font-number, resolution, name, symbol-set, spacing, width, height, style, stroke, type-face, type; Parameters font-number: font number: 1000 to 65535 resolution: resolution: 0 = 300-dpi bitmap 1 = 600-dpi bitmap 3 = 1200-dpi bitmap - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 162
160 to 255 2 = character codes from 0 to 255 Function The LDFN F command creates a font header for downloading a font to the printer. After the header is created, you must continue with downloading bitmap characters using the LDFN C command. This command only generates a font information header; it - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 163
font 2 = Japanese TrueType Collection font font-number: font number: 1000 to 65535 Since there are two font headers for Japanese TrueType fonts, the printer automatically creates a font number increased by 1. name: font name: ASCII text string of up to 31 characters long. This string must be - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 164
data length). Always explicitly terminate font data using WRED;. The five bytes represented by WRED; are not counted as part of the font data length. The maximum number of fonts that can be downloaded is up to the memory available or 256 fonts (512 when format is 2). Use FONT or SFNT command - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 165
LGHT LGHT - adjust LiGHTness COLOR Format LGHT mode, degree; Parameters mode: mode of lightness adjustment: 0 = gamma control 1 = contrast control degree: degree of saturation level: number from -10 to 10 (Default is 0) Function The LGHT command controls lightness and darkness balance - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 166
hue, you need to control with care. The LGHT command is enabled for all color spaces, all color modes and all monitor simulation modes. If ink simulation is set to other than none, this command is disabled. This mode is not held permanently in the printing system. For this reason, saturation - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 167
MAP MAP - Move to Absolute Position Format MAP x-coordinate, y-coordinate; Parameters x-coordinate: distance from the left margin y-coordinate: distance from the top margin Function The MAP command moves the cursor to a position specified relative to the top and left margins, measured in the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 168
PRESCRIBE Command Reference Printout Related Commands MRP, MZP, MRPA 158 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 169
MCLR MCLR - Match CoLoR COLOR Format MCLR mode; Parameter mode: mode of color matching: 0 = none (default) 1 = auto 2 = vivid color 3 = display Function The MCLR command selects the mode of color matching. Color matching mode is changed according to the various conditions of emulation, paper - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 170
the old definition with the DELM (delete macro) or DAM (delete all macros) command, or by switching power off. See the Technical Reference manual for information on the limitations about the usage of macros. The PCL5E command language, available in the mode 6 emulation, enables users to record HPGL - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 171
mode is used. See also Resource Protection in the Technical Reference manual. Macro Downloaded Memory card Internal Location RAM Memory card ROM Property Temporary/Permanent Permanent Permanent The internal printer firmware manages the PCL macros, recognizing the source, location and property - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 172
PRESCRIBE Command Reference MDAT - set MeDia type ATtribute Format MDAT [media-type[, paper-weight, fuser-mode, duplex[, density]]]; Parameters media-type 1 = Plain 2 = Transparency 3 = Preprinted 4 = Label 5 = Bond 6 = Recycled 7 = Vellum 8 = Rough 9 = Letterhead 10 = Color 11 = Prepunched 12 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 173
affects the printing system's transfer bias, fuser-mode affects the fuser temperature, and duplex determines whether the paper with that paper type is allowed for duplex printing or not. If the parameters paper-weight and fuser-mode are omitted, this command resets the three attributes back to their - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 174
it is changed by another MID command (It is not reset by the RES command). If the printer receives an ASTK command or one of the FRPO commands, the 2;) or off (FRPO S0, 0;). Refer to the sorter's User's Manual. Note File This command is irrelevant to certain combination of photocopier models and - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 175
MPSS MPSS - e-MPS Storage Format MPSS 'job-type', 'limit', size; Parameters job-type: CODE = temporary or permanent job VMB = virtual mailbox job JOBR = retention job limit: TEMPLIMITSIZE = Limit of the capacity for temporary stored jobs PERMLIMITSIZE = Limit of the capacity for permanent - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 176
0, this message is disabled despite the MP tray is empty and the other paper source(s) is not empty. (showing Ready, for example). It is not reset by the RES command, therefore, to change mode, the MPTE command should be used. File To configure the MP tray as the default paper source - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 177
MRP MRP - Move to Relative Position Format MRP x-coordinate, y-coordinate; Parameters x-coordinate/y-coordinate: coordinates as measured from the current cursor position Function The MRP command moves the cursor from its current position to a specified relative position, measured in the units - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 178
PRESCRIBE Command Reference Printout Related Commands MAP, MZP, MRPA 168 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 179
MRPA MRPA - Move to Relative Position specified by Angle Format MRPA distance, angle; Parameters distance: distance to move angle: angle in degree, measured clockwise from the vertical Function The MRPA command moves the cursor from its current position across a specified distance using a - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 180
PRESCRIBE Command Reference Printout Related Commands MAP, MRP, MZP 170 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 181
only when the option sorter is installed with the printing system. It instructs the printing system to deliver printed pages in the mailbox mode. In the bulk tray are used. Upon receiving the MSTK command, the printer automatically performs a page feed. The MSTK 0; command is applicable only - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 182
: !R! PSRC 100; EXIT;. For details see the PSRC (set paper source) command section in this manual. To ensure that the paper having the correct size and type of media is always selected, it is 8;. This command is valid only for the print systems that support the automatic media type function. 172 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 183
tray, set the MP tray size to A4 and the MP tray type to Labels (See the user's manual for details.) !R! RES; PSRC 100; CMNT Sets the printer to automatic casette mode; CMNT Depending on the current media type; SPSZ 8; MTYP 4; CMNT Paper size = A4, media type = label; RES; EXIT; Related Commands - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 184
PRESCRIBE Command Reference MZP - Move to Zero-relative Position Format MZP x-coordinate, y-coordinate; Parameters x-coordinate: distance from the left edge limit of paper y-coordinate: distance from the top edge limit of paper Function The MZP command moves the cursor to a position specified - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 185
MZP Printout Related Commands MAP, MRP, MRPA 175 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 186
or draws a line along it (STRK, FILL). For a full description of path, refer to Chapter 1 of the Technical Reference manual. File !R! RES; UNIT C; NEWP; PMZP 5, 5; PDRP 1, -2, 3, 0, -1, 2, -3, 0; STRK; CMNT Stroking the path; NEWP; PMZP 10, 5; PDRP 1, -2, 3, 0, -1, 2, -3, 0; GPAT .5; FILL 1; CMNT - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 187
option mailbox 6 71 = face-down output tray of the option mailbox 7 72 = face-up output tray of the option mailbox 7 Function The OTRY command instructs the printing system to deliver pages to the corresponding output stack of the printing system or the option stacker. The selected tray remains in - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 188
delivered face-down as usual, page 1 first. !R! PAGE; EXIT; PAGE 2 PAGE 2 next, and so on, stacking in the correct order. !R! PAGE; EXIT; PAGE 3 But on printers with two paper trays this file will be delivered to the face-up tray with the pages in reverse order, page 3 on top. !R! PAGE; EXIT - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 189
PAGE PAGE - start new PAGE Format PAGE; Parameter None Function The PAGE command causes a page break without resetting the printer. Subsequent data will be printed on a new page with no changes made to page formatting parameters such as spacing, margins, font selection. If there is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 190
PRESCRIBE Command Reference PANT - create PANTone color palette COLOR Format PANT color-number or 'color-name'; Parameters color-number: Pantone color number, integer from 100 to 5999 color-name: Pantone color name Function The PANT command can be used to specify the PANTONE uncoated color by - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 191
4 Warm Gray 4 Warm Gray 8 Cool Gray 4 Cool Gray 8 The PANT command may not work with certain printer models and versions. Set the print quality to Quick mode when this command is used with model FS-5800C. PANTONE colors cannot be used by the PANT command in KPDL emulations. !R! PANT 'Cool Gray - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 192
PRESCRIBE Command Reference PARC - in Path, draw ARC Format PARC x-coordinate, y-coordinate, radius, start-angle, end-angle; Parameters x-coordinate, y-coordinate: coordinates of the center of arc, measured from the left and top edge limits radius: radius of arc start-angle: starting angle, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 193
PARC Printout 183 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 194
through 60 if a resident pattern is selected. A full list of the printer's resident patterns appear on the following page. Pattern numbers 100 through 105 patterns are defined, the printer selects the No. 1 (solid black) resident pattern. Variable resolution support is valid for 600 dpi and 1200 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 195
PAT Resident Fill Patterns (300 dpi) 185 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 196
PRESCRIBE Command Reference PCRP - in Path, Curve to Relative Position Format PCRP x1, y1, x2, y2, x3, y3; Parameters x1, y1: coordinates of the first control point as measured from the current cursor position x2, y2: coordinates of the second control point as measured from the current - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 197
File !R! RES; UNIT C; NEWP; SPD .1; PMZP 3, 3; PCRP 4, 2, 5, 1.5, 6, 1.8; STRK; PAGE; EXIT; Printout Current positon (5, 1.5) (4, 2) (6, 1.8) File !R! RES; UNIT C; NEWP; SPD .1; PMZP 3, 3; PCRP 5.5, 1.5, 1.5, 5.5, 7, 7; STRK; PAGE; EXIT; Printout Current positon (5.5, 1.5) PCRP (1.5, 5.5) - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 198
PRESCRIBE Command Reference PCZP - in Path, Curve to Zero-relative Position Format PCZP x1, y1, x2, y2, x3, y3; Parameters x1, y1: coordinates of the first control point as measured from the left and top edge limits of paper x2, y2: coordinates of second control point as measured from the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 199
File !R! RES; UNIT C; PMZP 3, 6; PCZP 11, 3, 2, 2, 9, 6; STRK; PAGE; EXIT; Printout (2, 2) PCZP (11, 3) (9, 6) Current position (3, 6) 189 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 200
PRESCRIBE Command Reference PDIR - set Print DIRection Format PDIR angle; Parameter angle: angle in degrees; in 90° increments in a counterclockwise direction 0 = portrait 90 = landscape 180 = reverse portrait 270 = reverse landscape Function The PDIR command rotates the coordinates of the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 201
Portrait (PDIR 0;) Landscape (PDIR 90;) PDIR Reverse Landscape (PDIR 270;) Reverse Portrait (PDIR 180;) File !R! RES; UNIT P; SFNT 'Helvetica', 8; UNIT C; MZP 10, 12; SPD .144; CIR .075; PDIR 270; TEXT ' ENDLESS VARIETY AND VERSATILITY'; PDIR 180; TEXT ' ENDLESS VARIETY AND VERSATILITY'; PDIR - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 202
PRESCRIBE Command Reference Printout 192 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 203
outside the current page. The thickness of the line is designated by the SPD command. Multiple pairs of coordinates may be specified. The printer then draws a connected series of line segments, proceeding from one point to the next. For example, PDRP 1, 2, 3, 4; is equivalent to PDRP 1, 2; PDRP - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 204
PRESCRIBE Command Reference Printout Related Command PDZP 194 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 205
PDZP PDZP - in Path, Draw to Zero-relative Position Format PDZP x-coordinate, y-coordinate; Parameters x-coordinate, y-coordinate: coordinates as measured from the left and top edge limits of the current page Function The PDZP command adds a line to the current path from the current cursor - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 206
PRESCRIBE Command Reference Printout Related Command PDRP 196 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 207
PELP PELP - in Path, draw ELlipse Format PELP x-diagonal, y-diagonal[, x-start, y-start, x-end, y-end[, ellipsepath]]; Parameters x-diagonal: X-coordinate of diagonal point of bounding box y-diagonal: Y-coordinate of diagonal point of bounding box x-start: X-coordinate of start control point - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 208
PRESCRIBE Command Reference Current cursor position (x-end, y-end) (x-start, y-start) Bounding box (x-diagonal, y-diagonal) N : C : P : File !R! RES; UNIT C; MZP 0, 0; BOX 2, 3; NEWP; PMZP 0, 0; PELP 2, 3, 2, 0, 0, 0, N; STRK; MZP 5, 5; BOX 2, -3; NEWP; PMZP 5, 5; PELP 2, -3, 2, 0, 0, 0, N; STRK - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 209
fractions.) The sum of the slice sizes should not exceed 9999. The total length of the command must not exceed 255 characters. The printer automatically converts the slice sizes to angles totaling 360 degrees. It draws the first slice starting at the position specified by the second parameter - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 210
PRESCRIBE Command Reference Printout 200 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 211
PMRA PMRA - in Path, Move to Relative position specified by Angle Format PMRA x-coordinate, y-coordinate, distance, angle; Parameters x-coordinate, y-coordinate: coordinates as measured from the left and top edge limits of the page distance: distance specified in increments governed by the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 212
PRESCRIBE Command Reference File !R! RES; UNIT C; SPD 0.2; NEWP; PMRA 10, 19, 5, 45; PARC 10, 19, 5, 45, 135; STRK; PAGE; EXIT; Printout 202 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 213
PMRP PMRP - in Path, Move to Relative Position Format PMRP x-coordinate, y-coordinate; Parameters x-coordinate, y-coordinate: coordinates as measured from the current cursor position Function The PMRP command moves the cursor from its current position to a specified relative position in a path - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 214
PRESCRIBE Command Reference Printout Related Command PMZP 204 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 215
PMZP PMZP - in Path, Move to Zero-relative Position Format PMZP x-coordinate, y-coordinate; Parameters x-coordinate, y-coordinate: coordinates as measured from left edge limit of the current page Function The PMZP command moves the cursor to a position in a path construction, specified relative - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 216
PRESCRIBE Command Reference Printout Related Command PMRP 206 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 217
PNCH PNCH - PuNCH Format PNCH[ mode]; Parameter mode: number of punched holes: 1 = 2 (Europe) or 3 (U.S.) 2 = 4 (Europe) or 2 (U.S.) 51 = 2 (Europe) or 3 (U.S.), left 52 = 4 (Europe) or 2 (U.S.), left 61 = 2 (Europe) or 3 (U.S.), right 62 = 4 (Europe) or 2 (U.S.), right 71 = 2 (Europe) or 3 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 218
PRESCRIBE Command Reference File The mode parameters of 51, 52, 61, 62, 71, and 72 are valid for some copier models only. These parameters allow to position the holes in either of the left, right, and top sides of the page by logically aligning the page in reference to the punched holes. Note that - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 219
PRBX PRBX - in Path, draw Round BoX Format PRBX width, height, radius; Parameters width: width of round box height: height of round box radius: radius of round box corners Function The PRBX command adds a round box path to the current path. This command close the sub-paths but does not stroke - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 220
PRESCRIBE Command Reference File !R! RES; UNIT C; SPD 0.125; NEWP; PMZP 1, 1; PRBX 11.7, 1.7, 0.5; STRK; MZP 1.5, 2.15; SFNT "Helvetica-Bd", 24; TEXT "CAUTION: HOT SURFACE!"; PAT 5; NEWP; PMZP 1, 4; PRBX 5, 2.4, 0.3; FILL; MZP 1.4, 4.7; SFNT "Helvetica-Nr", 12; TEXT "Barefoot Systems, Inc.", L; TEXT - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 221
PRRC PRRC - in Path, at Relative position, draw aRC Format PRRC x-coordinate, y-coordinate, radius, start-angle, end-angle; Parameters x-coordinate/ y-coordinate: coordinates as measured from the current cursor position radius: radius of arc start-angle: starting angle, measured - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 222
PRESCRIBE Command Reference PRRC 1, 1, 180, 0; Negative values are acceptable for angle. For example, an angle of 315 degrees is the same as -45 degrees. File !R! RES; SPD 0.05; MZP 4.5, 5; NEWP; PRRC -1, 0, 1, 90, 270; PRRC 1, -2, 1, 0, 180; PRRC 2, 1, 1, -90, 90; PRRC -1, 2, 1, 180, 0; STRK; PAGE; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 223
PSRC PSRC - select Paper SouRCe Format PSRC mode; Parameter mode: 0 = multi-purpose tray 1 = Cassette 1 2 = Cassette 2 3 = Cassette 3 4 = Cassette 4 5 = Cassette 5 6 = Cassette 6 99 = envelope feeder 100 = automatic Function The PSRC command selects whether to feed paper from the cassette, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 224
(3, 4), a different result is obtained depending on each pixel placement mode. Grid intersection is default to HP PCL; and grid centered mode is used by Microsoft Windows. This command is ignored when used with DAP, DRP, DRPA, DZP, BOX, BLK, CIR, ARC, or PIE. This command has no effect for text or - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 225
changes can be made with the FRPO command described in Chapter 6 of the Technical Reference manual. If !R! is used by mistake when the printer is already in the PRESCRIBE mode, the printer ignores the mistaken !R! and whatever follows, up to the next semicolon. File !R! SFNT 'Helvetica', 14 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 226
PRESCRIBE Command Reference Printout Related Commands EXIT, SCRC 216 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 227
RCLT RCLT - Rotated CoLlaTion Format RCLT; Parameter None Function The RCLT command instructs the printing system to stack the sets on the tray in alternating orientations. The RCLT command require a hard disk installed in the printing system or a - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 228
PRESCRIBE Command Reference RDMP - Received-data DuMP Format RDMP; Parameter None Function The RDMP command causes all subsequent data to be printed in hexadecimal form (two hexadecimal digits per character) until an ENDD (END Dump) command is received, or until the printing system runs out of data - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 229
Sample RDMP 219 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 230
FRPO command. For these, the factory reset value is given, followed by the FRPO parameters that can be used to change this value in parenthesis. In HP-7475A emulation, the RES command resets the printer environment in the same manner as the KC-GL DF instruction. Refer to section HP 7550A Emulation - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 231
RES Parameter Value after reset (Related FRPO parameter) LaserJet (PCL) IBM/Epson Diablo Related or V3 (scalable SFNT font)a Alternate font assignment None See Emulation of ← the Technical Reference manual. SETF Country code 0 (U6)† ← ← INTL Symbol set Roman-8 (U6/7) See Emulation - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 232
PCL resources (fonts, macros, patterns, and symbol sets) which have been downloaded into RAM to be purged. The printing system's resolution setting enabled by this command is reset to default (FRPO N8), if a command which results in reset (RES, FRPO and SEM) is received. Actual resolution may be - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 233
Color balance decreased Default color balance (B) Color balance increased Color balance decreased Varying color balance allows the output image results to vary. Issuing this command resets hue, saturation, and luminosity control values to their default settings. 223 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 234
Reference This command is enabled for all color spaces, all color modes and all monitor simulation modes. If ink simulation is set to other than none, this command is disabled. The RES command resets saturation to its default state. This mode is not held in the printing system. For this reason - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 235
is in HP emulation mode. Since this command is PCL command-compatible (&l #U, & l #Z), the offset values are cleared to zero only by a software reset (E). In other words, the offset is only cleared by PRESCRIBE (RES and FRPO INIT commands) when the emulation is HP. An error will - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 236
PRESCRIBE Command Reference RPCS - Return to Previous Code Set Format RPCS; Parameter None Function The RPCS command resumes use of a code set saved by a previous SCCS (save current code set) command. The RPCS commands return to the code sets in reverse order in which they were nested. File See SCCS - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 237
RPF RPF - Return to Previous Font Format RPF; Parameter None Function The RPF command resumes use of a font saved by a previous SCF (save current font) command. The RPF commands return to the fonts in the reverse order in which they were saved. SCF and RPF are particularly useful in macros. File !R! - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 238
PRESCRIBE Command Reference RPG - Return to Previous Graphics state Format RPG; Parameter None Function The RPG command restores the graphics state most recently saved by a SCG (Save Current Graphics) command. The following items of graphics state revert to the state saved previously. • Path and - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 239
RPG Printout Related Command SCG 229 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 240
PRESCRIBE Command Reference RPP - Return to Previous Position Format RPP; Parameter None Function The RPP command moves the cursor to a position saved by a previous SCP (save current position) command. If the RPP command is executed by mistake when no previous position has been saved, the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 241
RPP Printout Related Command SCP 231 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 242
PRESCRIBE Command Reference RPPL - Return to Previous PaLette COLOR Format RPPL; Parameter None Function The RPPL command restores the color palette most recently saved by a SCPL (save current palette) command. A color palette restored using the RPPL command immediately becomes active. If the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 243
RPU RPU - Return to Previous Unit Format RPU; Parameter None Function The RPU command brings the unit of measurement (inches, centimeters, points, or dots; as specified by the UNIT command) back to the unit saved by the SCU (save current unit) command. File/Printout See SCU on page 283. Related - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 244
PRESCRIBE Command Reference RTTX - RoTate TeXt Format RTTX angle, 'string'[, U-option]; Parameters angle: angle of rotation in degrees string: character string U-option: Underline text Function Taking the normal output angle for text as zero, the RTTX command rotates a character string - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 245
RTTX Printout 235 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 246
PRESCRIBE Command Reference RTXT - print Right-aligned TeXT Format RTXT['string'][,option][,U-option]; Parameters string: any character string option: B = Leave cursor at back end of string E = Move cursor to front end of string L = Move cursor down one line N = Move cursor to beginning of - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 247
File !R! RES; UNIT P; SFNT 'TimesNewRoman'; UNIT I; MCRO PF; MRP .15, 0; BOX .1, -.1; MRP .5, 0; BOX .1, -.1; MRP -.65, 0; ENDM; MAP 3, 3; TEXT 'Pass Fail', L, U; CALL PF; RTXT 'Unit test', L; CALL PF; RTXT 'Integration test', L; PAGE; EXIT; Printout RTXT 237 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 248
PRESCRIBE Command Reference RVCD - ReceiVe Compressed raster Data Format RVCD[ compression-mode]; length, data, ... ; Parameters compression-mode: 0 = uncompressed 1 = run-length encoding 2 = TIFF (Tagged Image File Format) [rev. 4.0] length: bytes of raster data data: binary raster data, 0H - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 249
RVCL RVCL - ReceiVe CoLor raster data COLOR Format RVCL [compression-mode,] length, data; Parameters compression-mode: 0 = uncompressed (Default) 1 = run-length encoded 2 = TIFF (Tagged Image File Format) [rev. 4.0] length: bytes of raster data data: binary raster data, 0H to FFH Function - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 250
PRESCRIBE Command Reference RVRD - ReceiVe Raster Data Format RVRD; number of data, data, ... ; Function The RVRD command declares the start of raster data. Raster data represents dot lines encoded as numeric values as shown below. Each dot line is divided into 8-dot segments. Each segment is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 251
which follows. The subsequent data can be obtained by following the same procedure as explained in Defining Fill Patterns in Chapter 2 of the Technical Reference manual. 241 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 252
disk A = memory card data-type: type of data to be deleted 1 = Font data 2 = Printable data 16 = Macro data 112 = File data 128 = API data (downloadable program) partition-name: Name of partition from which data is deleted Function The RWER D command deletes data on any external media whether it is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 253
RWER F RWER F - [Read/Write External Resource] Format external media Format RWER F, medium; Parameter medium: 0 = hard disk A = memory card Function The RWER F command formats any external media whether it is a memory card or the hard disk. The hard disk is physically formatted when it is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 254
PRESCRIBE Command Reference RWER I - [Read/Write External Resource] automatically print partition Information Format RWER I, mode; Parameter mode: control mode: E = Enable automatic printing of partition information D = Disable automatic printing of partition information Function The RWER I - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 255
RWER L RWER L - [Read/Write External Resource] print partition List Format RWER L[, medium]; Parameter medium: 0 = hard disk or RAM disk A = memory card E = EPROM Function The RWER L command explicitly prints partition lists for any external media whether it is a memory card, the hard disk, or - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 256
-type, 'partition-name'; Parameters medium: 0 = hard disk or RAM disk A = memory card E = EPROM data-type: 2 = Printable data 128 = API data (downloadable program) partition-name: Name of partition from which data is read, a maximum of 15 printable ASCII characters Function The RWER R command - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 257
RWER S RWER S - [Read/Write External Resource] Store TrueType font Format RWER S, medium, font-type, file-name, font-name, length[, value, style, weight, type-face];binary-data WRED; Parameters medium: drive specification: 0 = hard disk or RAM disk A = memory card font-type: font type: 0 = - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 258
The RWER S command allows outline fonts (in TrueType format) to be downloaded to the printing system and to be stored on the specified media as data using WRED;. The five bytes represented by WRED; are not counted as part of the font data length. Since value, style, weight and type-face represent - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 259
RWER T RWER T - [Read/Write External Resource] set Terminate string Format RWER T[, 'terminator']; Parameter terminator: ASCII text string up to 4 bytes, enclosed in either single or double quotation marks Function The RWER T command sets a terminator string for external media whether it is a - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 260
medium: 0 = hard disk or RAM disk A = memory card data-type: 1 = Font data 2 = Printable data 16 = Macro data 112 = File data 128 = API data (downloadable program) partition-name: Name of partition to which data is written, in a maximum of 15 printable ASCII characters. If this parameter is omitted - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 261
RWER W 1. Verify the printing system's message display indicates Ready. 2. Enter the following at the DOS prompt: C:\>ECHO !R! RWER W, A, 2, 'DATA123'; >PRN The message display will change from Ready to Processing, and then to Waiting. The printing system is now ready to receive data, so send the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 262
PRESCRIBE Command Reference RWRF D - [Read/Write Resource File] Delete data on external device Format RWRF D, medium, data-type, "file-name"; Parameters medium: 0 = hard disk A = memory card data-type: "API" API program "FNT" Font data "MCR" Macro data "PRN" Printable data file-name: ASCII text - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 263
RWRF F RWRF F - [Read/Write Resource File] Format external device Format RWRF F, medium; Parameters medium: 0 = hard disk A = memory card Function The RWRF F command physically and logically formats an external device such as the hard disk. This command has no effect if the target device has - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 264
PRESCRIBE Command Reference RWRF L - [Read/Write Resource File] print resource file List Format RWRF L[, 'medium']; Parameters medium: 0 = hard disk A = memory card Prints a resource file list for all devices if omitted. Function The RWRF L command prints a resource file list registered in an - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 265
RWRF P RWRF P - [Read/Write Resource File] set hidden file Format RWRF P, medium, data-type, "file-name"; Parameters medium: 0 = hard disk A = memory card data-type: "API" API program "FNT" Font data "MCR" Macro data file-name: ASCII text string up to 15 bytes. Function The RWRF P command sets - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 266
PRESCRIBE Command Reference RWRF R - [Read/Write Resource File] Read Format RWER R, medium, "PRN", 'partition-name'; Parameters medium: 0 = hard disk A = memory card partition-name: Name of partition from which data is read, a maximum of 15 printable ASCII characters Function The RWRF R command - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 267
RWRF T RWRF T - [Read/Write Resource File] set Terminate string Format RWRF T[, 'terminator']; Parameters terminator: ASCII text string up to 4 bytes Set to default "WRED" if omitted. Function The RWRF T command changes a terminator (default: WRED). The terminator that was changed with this - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 268
hard disk. The number of writable files, which is not limited, depends on the capacity of the external media. If the device runs out of free space during saving, the remaining data will be discarded. Duplicating a file name causes the system to rename the specified one and save data (without - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 269
: ASCII text string up to 31 bytes Up to 28 bytes for font type 2 font-data-length: Number of bytes in font data to be downloaded symbol-set-value: 1 to 65535 (619 = Shift JIS code) font-style: 0 to 32767 stroke-weight: -127 to +127 typeface: 0 to 32767 259 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 270
PRESCRIBE Command Reference Function The RWRF W command writes data to an external device such as the hard disk. The available number of fonts is max. 512 in the same compact flash and max. 4096 in the hard disk. Duplicating a file name causes the system to rename the specified one and save data ( - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 271
hard disk. The number of writable files, which is not limited, depends on the capacity of the external media. If the device runs out of free space during saving, the remaining data will be discarded. Duplicating a file name causes the system to rename the specified one and save data (without - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 272
hard disk. The number of writable files, which is not limited, depends on the capacity of the external media. If the device runs out of free space during saving, the remaining data will be discarded. Duplicating a file name causes the system to rename the specified one and save data (without - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 273
with hue, you need to control with care. This command is enabled for all color spaces, all color modes and all monitor simulation modes. If ink simulation is set to other than None, this command is disabled. This mode is not held in the printing system. For this reason, saturation is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 274
PRESCRIBE Command Reference SBM - Set Bottom Margin Format SBM length; Parameter length: distance from top of paper to bottom margin Function The SBM command sets the bottom margin, as measured from the top edge limit of the paper in the units designated by the UNIT command. If an attempt is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 275
SBM Printout 265 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 276
PRESCRIBE Command Reference SCAP - Set line CAP Format SCAP mode; Parameter mode: line cap mode: 1 = square caps 2 = butt caps 3 = round caps Function The SCAP command determines the shape of line ends (or a line cap) in a path where they are finally stroked. The default caps is butt caps (2). - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 277
SCAP Printout 267 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 278
PRESCRIBE Command Reference SCCS - Save Current Code Set Format SCCS; Parameter None Function The SCCS command instructs the printing system to remember the code set of the current font. This command may be used in conjunction with a SCF (save current font) command - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 279
SCCS Printout Related Commands RPCS, RPF, SCF 269 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 280
to eight font numbers can be saved in the printing system's memory by SCF commands (using a separate SCF command for each). The SCF command only instructs the printing system to remember the font. It does not move actual fonts in or out of memory. File !R! RES; SLM 1; STM 2; SFNT 'TimesNewRoman - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 281
SCF Printout Related Command RPF 271 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 282
PRESCRIBE Command Reference SCG - Save Current Graphics state Format SCG; Parameter None Function The SCG command saves the graphics state comprised of the following characteristics: • Current path and cursor position • Current pen diameter • Current line join • Current line cap • Current miter - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 283
SCG Printout Related Commands FILL, RPG 273 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 284
PRESCRIBE Command Reference SCOL - Select COLor COLOR Format SCOL number; Parameter number: number from 0 to 255 (Default is 0.) Function The SCOL command selects a color from the currently active palette. If no color is assigned to the specified number, this command is ignored. If the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 285
SCP SCP - Save Current Position Format SCP; Parameter None Function The SCP command instructs the printing system to remember the current cursor position, so that it can be retrieved later using the RPP (return to previous position) command. Up - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 286
PRESCRIBE Command Reference SCPI - Set Characters Per Inch Format SCPI number; Parameter number: number of characters per inch Function The SCPI command sets the number of characters per inch (even if the UNIT command designates a non-inch unit). When a proportionally-spaced font is used and - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 287
SCPI Printout Related Command SCS 277 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 288
PRESCRIBE Command Reference SCPL - Save Current PaLette COLOR Format SCPL; Parameter None Function The SCPL command saves the currently active palette, so that it can be retrieved later using the RPPL (return to previous palette) command. Palettes can be saved as many as there is enough memory - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 289
character between the exclamation points in the PRESCRIBE start sequence. The change remains in effect until power is turned off or a RES (reset) command is executed. Originally the command recognition character is the capital letter R within the PRESCRIBE start sequence of !R!. One reason for - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 290
PRESCRIBE Command Reference Printout 280 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 291
SCS SCS - Set Character Spacing Format SCS distance; Parameter distance: character-to-character spacing, or 0 Function The SCS command sets the distance from the beginning of one character to the beginning of the next character. When a proportionally-spaced font is used and the font mode (FTMD) - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 292
PRESCRIBE Command Reference SCSZ - Set Custom paper SiZe Format SCSZ width, height, unit; Parameters width: width of custom paper size height: height of custom paper size unit: M = millimeters I = inches Function The SCSZ command sets the paper size when the user-defined size paper is used - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 293
Unit Format SCU; Parameter None Function The SCU command instructs the printing system to save the current unit of N8, 0; RES; SENT "Univers-MdCd", 9; UNIT C; SCU; MZP 1.5, 1.5; TEXT "THE DAYS ON THE ISLAND: PART I", U; MCRO TITLE; FSET 24V; UNIT I; MZP 4, 3; CIR 2; MRP -1.5, .125; TEXT %1; ENDM; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 294
PRESCRIBE Command Reference Printout Related commands SCF, SCP, UNIT 284 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 295
SDP SDP - Store Dash Pattern Format SDP pattern-number, dash1, space1, dash2, space2, ..., dash10, space10; Parameters pattern-number: number from 11 to 20 dash1 ... 10: length of dash space1 ... 10: space between dashes Function The SDP command generates a new dash pattern used by the DPAT ( - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 296
PRESCRIBE Command Reference File !R! RES; UNIT P; SDP 11, 2, 2, 5, 5; NEWP; UNIT C; SPD .2; PMRA 10, 10, 3, 0; DPAT 11; PARC 10, 10, 3, 0, 360; STRK; PAGE; EXIT; Printout Related Command DPAT 286 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 297
SEM SEM - Set Emulation Mode Format SEM mode; Parameter mode: 0 = Line Printer 1 = IBM Proprinter X-24E 2 = Diablo 630 5 = Epson LQ-850 in effect until another SEM or an RES (reset) command is issued. The SEM command also resets the margins and various other parameters. It should therefore - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 298
low alternate numbers so that SETF commands can be embedded for some word processing software. See Emulation of the Technical Reference manual. File !R! RES; SFNT 'Helvetica', 10, 2000; SFNT 'Helvetica-BdOb', 10, 2001; SETF 1, 2000; SETF 2, 2001; MCRO BIBLIO; ALTF 1; TEXT %1, E; TEXT " ", E; ALTF - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 299
SETF Printout 289 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 300
PRESCRIBE Command Reference SFA - Set bitmap Font Attributes Format SFA hmi, vmi, F/P[, rotation, symbol-set, height, U/I, weight, typeface][, font-type]; Executable Parameters hmi: horizontal motion index; in a fixed font, the distance from the center of one character to the center of the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 301
degree of bolding, from -7 (light) to +7 (bold) type-face: 0 = Line Printer 1 = Pica 2 = Elite 3 = Courier 4 = Swiss 721 5 = Dutch 801 See Emulation of the Technical Reference manual.) Function The SFA command specifies the Font attributes are not reset by the RES (reset) command. The SFA command - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 302
parameters must also be specified. The optional parameters are used to describe downloaded fonts for selection by embedded commands in the HP LaserJet emulation mode. spaced (0.5 cm) with 1.5 mm spaces between words. !R! FONT 1; EXIT,E; The printer remembers the spacing assigned to each font. 292 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 303
SFA Printout 293 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 304
FONT command recalls the font with these effects intact. type-face should be a name from the font table in Section 4.2. of the Technical Reference manual. Specify the full name exactly as it appears in the table, including case sensitivity. This command is ignored and the current font is not changed - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 305
SFNT height parameter is omitted, the printing system sizes the font to the height of the current font. The following example displays a range of font heights. You can assign any number from 1000 to 65535 as a temporary font-number, as long as you do not duplicate the number of a bitmap font or a - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 306
PRESCRIBE Command Reference This is 10-point Helvetica-Nr, with Roman-8 symbol set, compression is 2, and shear is .3. You can later recall this font by the FONT 3000; command. !R! PAGE; EXIT; Printout 296 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 307
SGPC SGPC - Set kcGl Pen Color COLOR Format SGPC pen-number, color; Parameters pen-number: number from 1 to 8 corresponding to FRPO G1 to G8 parameter color: 0 = Black 1 = Red 2 = Green 3 = Yellow 4 = Blue 5 = Magenta 6 = Cyan 7 = White Function The SGPC command sets the color of a pen 1 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 308
PRESCRIBE Command Reference SHMI - Set HMI Format SMHI hmi; Parameter hmi: horizontal motion index; in a fixed font, the distance from the center of one character to the center of the next; in a proportionally spaced font, the width of the space character Function The SHMI command sets the HMI. - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 309
SIMG SIMG - Set IMaGe model Format SIMG operation-mode; Parameter operation-mode: Source image 1 = Transparent 2 = Opaque 3 = Transparent 4 = Transparent 5 = Opaque 6 = Opaque Pattern image - - Transparent Opaque Transparent Opaque Function The SIMG command sets the mode for controlling the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 310
PRESCRIBE Command Reference The figure on the next page illustrates the effects of operation mode 3 through 6. In this example, the letter A represents the source image overlaid with the pattern image, while the two rectangles are referred to as the destination image. operation-mode = 3: Both the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 311
File !R! RES; UNIT C; NEWP; PMZP 5, 5; PDRP 2.5, 0, 0, 2.5, -5, 0, 0, 2.5, 2.5, 0; PAT 1; SIMG 4; FILL 1; MRP -1, 3.5; PAT 18; FSET 4158T3B0S1P108V; TEXT "A"; FILL 1; PAGE; EXIT; Printout SIMG 301 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 312
PRESCRIBE Command Reference SIMP - create SIMPle color palette COLOR Format SIMP palette; Parameter palette: 1 = single plane K (Black) palette (Default) 3 = 3-plane device RGB palette Function The SIMP command creates a palette already defined by the system from either a single plane ( - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 313
File !R! RES; UNIT C; SIMP 3; MCRO SIMP; NEWP; SCOL %2; PDRP 2, 0, 0, 2, -2, 0, 0, -2; FILL 1; PMRP .5, .5; ENDM; CALL SIMP,0,0; CALL SIMP,0,1; CALL SIMP,0,2; CALL SIMP,0,3; CALL SIMP,0,4; CALL SIMP,0,5; CALL SIMP,0,6; CALL SIMP,0,7; PAGE; EXIT; Printout SIMP 303 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 314
2 = On (Medium) Function The SIR command accesses different levels of Kyocera Image Refinement (KIR). The image refinement level remains in effect until the SIR command. The default value is On. Refer to the User's Manual for details about how to obtain the optimum level of the image refinement. File !R! - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 315
SLJN SLJN - Set Line JoiN Format SLJN mode; Parameter mode: line join mode: 1 = Beveled join 2 = Mitered join 3 = Round join 4 = Notched join Function The SLJN command determines how two connected lines in a path are joined. The default join is beveled (1). Beveled join ends the lines with butt - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 316
PRESCRIBE Command Reference File !R! RES; UNIT C; NEWP; SPD .5; SCAP 3; CMNT Round-capped at the upper-left corner; SLJN 3; CMNT Round-joined at other corners; PMZP 5, 16.5; PDRP 3, 0, 0, 3, -3, 0, 0, -3; STRK; NEWP; SCAP 1; CMNT Square-capped at the upper-left corner; SLJN 2; CMNT Mitered-joined - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 317
SLM SLM - Set Left Margin Format SLM distance; Parameter distance: size of left margin Function The SLM command sets the left margin, as measured from the left edge limit of the paper in the unit value designated by the UNIT command. If the margin is moved to the right of the current cursor - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 318
PRESCRIBE Command Reference Printout 308 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 319
SLPI SLPI - Set Lines Per Inch Format SLPI number; Parameter number: Number of lines per inch Function The SLPI command sets the number of lines per inch (even if the UNIT command designates a non-inch unit). File !R! RES; STM 2; SFNT "Helvetica"; EXIT; These lines have the default spacing of - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 320
PRESCRIBE Command Reference SLPP - Set Lines Per Page Format SLPP number; Parameter number: number of lines per page Function The SLPP command sets the bottom margin for an exact number of lines per page based on the current line spacing. As long as you do not change the line spacing or use - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 321
SLPP Printout 311 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 322
PRESCRIBE Command Reference SLS - Set Line Spacing Format SLS distance; Parameter distance: Line-to-line spacing Function The SLS command sets the distance from the base of one line to the base of the next line. The distance is measured in the unit value designated by the UNIT command. The - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 323
miter limit value is 10. In smaller miter-limit values, say 3, the miter join automatically switches to the beveled join. This switching prevents the problem of a spike extending beyond the intersection of the path because a small angle is used for the miter-join. Miter limit = 10 Miter limit - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 324
PRESCRIBE Command Reference File !R! RES; UNIT C; NEWP; PMZP 5, 15; SPD .5; SLJN 2; CMNT Mitered join; PDRP 1.5, -2, 1.5, 2, 1.5, -2, 1.5, 2, 1.5, -2, 1.5, 2; SMLT 10; CMNT Miter limit is 10; STRK; NEWP; PMZP 5, 19; SPD .5; SLJN 2; CMNT Mitered join; PDRP 1.5, -2, 1.5, 2, 1.5, -2, 1.5, 2, 1.5, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 325
the color temperature, etc. Parameters except monitor-name are enabled only when monitor-name value is 7 (custom). Resetting the printing system or switching emulation modes resets all custom parameters to the default states. The simulation provided by this command is enabled only when the device - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 326
to some color printing system models. At the time of release of this manual, the command is irrelevant to model FS-5800C; and monitor-name values of 0 and 2 are valid for model FS-8000C. Resetting the printing system and switching emulation mode reset all parameters to the default states. 316 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 327
SPAL is deleted when a new palette is created by the CID command. The active palette number does not change. All palettes are deleted by the reset command, leaving only the default palette. File and Printout See ACLI on page 12. 317 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 328
PRESCRIBE Command Reference SPD - Set Pen Diameter Format SPD diameter; Parameter diameter: line thickness Function The SPD command sets the thickness of the line used in the graphics commands (DRP, PDRP, etc.). The thickness is specified in the unit value designated by the UNIT command. The - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 329
SPD File !R! RES; UNIT C; STM 2; SLM 2; SLS .6; SFNT "Helvetica-Nr"; SPD 0.01; DRP 5, 0; TEXT ' 0.01 cm', N; SPD 0.02; DRP 5, 0; TEXT ' 0.02 cm', N; SPD 0.05; DRP 5, 0; TEXT ' 0.05 cm', N; SPD 0.1; DRP 5, 0; TEXT ' 0.1 cm', N; SPD 0.2; DRP 5, 0; TEXT ' 0.2 cm', N; PAGE; EXIT; Printout 0.01 cm 0.02 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 330
PRESCRIBE Command Reference SPL - Set Page Length Format SPL length; Parameter length: distance from top margin to bottom margin Function The SPL command sets the bottom margin, as measured from the top margin position in the unit value designated by the UNIT command. If an attempt is made to - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 331
SPL Printout 321 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 332
upright) L = landscape (lengthwise) Function The SPO command instructs the printing system how to orient the page, laying the paper width, then switch to landscape orientation, the printing system resets the top margin to zero. The printing system uses separate bitmap fonts manual for details. 322 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 333
SPO File !R! RES; SFNT 'TimesNewRoman-It', 10; CMNT This file is for an A4 cassette.; SPSZ 8; PAT 16, 300; UNIT C; MZP 4, 24; BOX 6, -6; MZP 7, 24; BOX 3, -3; BLK 3, -3; MZP 4, 24; TEXT, L; TEXT 'Portrait orientation'; SPO L; MZP 12, 10; BOX 6, -6; MZP 15, 10; BOX 3, -3; BLK 3, -3; MZP 12, 10; TEXT, - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 334
, B5 to A5] 7 = 86% [A4 to JIS B5] 8 = 94% [A4 to letter] 9 = 98% [Cassette size to cassette size × 98% ] 1 Inoperable if ratio is specified. 2 Not supported by some print systems 324 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 335
. For details, see the user's manual supplied with the printing system. If your printing system model supports the A3 size paper, the enlargement/ an SPSZ command with new enlargement/reduction ratio specified or a reset command is encountered. Note that the enlargement/reduction ratio parameter - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 336
PRESCRIBE Command Reference SPW - Set Page Width Format SPW width; Parameter width: width of page, from left margin to right margin Function The SPW command sets the right margin, as measured from the left margin position in the unit value designated by the UNIT command. If an attempt is made - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 337
SPW Printout Related Command SRM 327 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 338
PRESCRIBE Command Reference SRM - Set Right Margin Format SRM width; Parameter width: size of right margin Function The SRM command sets the right margin, as measured from the left edge limit of the paper in the unit value designated by the UNIT command. If an attempt is made to print beyond - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 339
SRM Printout Related Command SPW 329 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 340
PRESCRIBE Command Reference SRO - Set Raster Options Format SRO presentation-mode [, width, height]; Parameters presentation-mode: 0 = physical raster direction 1 = logical page direction width: width of raster area in dot; min. 1 to max. 4200 dots height: height of raster area in dot; min. - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 341
SRO presentation-mode = 0 The width and height of the raster area are defined based on the physical page regardless of the current page orientation. The current page orientation affects the position of the current point, however. Current point Width Height Current point Width Height Portrait ( - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 342
PRESCRIBE Command Reference SROP - Set Raster OPeration Format SROP value; Parameter value: logical operation value: 0 to 255 Function The SROP command applies logical functions (AND, OR, XOR, NOT) to source, texture, and destination. Possible logical operations provided by this command is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 343
CALL DBOX,2; CALL DBOX,3; RES; EXIT; Printout SROP 333 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 344
: number from 1 to the maximum (bottom) Function The SSTK command is effective only when the optional sorter is installed to the printing system. It instructs the printing system to deliver printed pages in the sorter mode. Each specified tray receives a complete set of pages, one copy of each. If - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 345
output tray of the DF-610 subtray Function The STAK command instructs the printing system to deliver pages to the corresponding output stack and so on, stacking in the correct order. !R! PAGE; EXIT; PAGE 3 But on printers with two paper trays this file will be delivered to the face-up tray with the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 346
PRESCRIBE Command Reference STAT - STATus Format STAT [mode]; Parameter mode: 0 = prints a user status page (default) 1 = prints a service person status page Function The STAT command instructs the printing system to print a page of status information, starting on a new page. The status page - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 347
STAT Sample Status Page User status page Service status page 337 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 348
PRESCRIBE Command Reference STM - Set Top Margin Format STM distance; Parameter distance: size of top margin Function The STM command sets the top margin, in the unit value designated by the UNIT command. A top margin setting in a document file should be placed at the beginning of the file or - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 349
STM Printout 339 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 350
PRESCRIBE Command Reference STPC - set STaPle Counter Format STPC [staple-count or letter M (or m)]; Parameter staple-count: number of sheets to be stapled at a time (When this parameter is omitted, '0' is assumed): 2 to 501 = divides output pages into stacks of pages of this value and staples - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 351
STPL - STaPLe Format STPL [position]; Parameter position: stapling position: 1 = bottom left, one staple 2 = top left, one staple 3 = left, two staples (straight for Legal size) 50 = top left, one staple 51 = top right, one staple 52 = left, two staples 53 = right, two staples 54 = top, two - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 352
current output stack which may be specified by STAK. (For the document finisher such as the DF-31, the MSTK command may be used to guide stapled pages to one of the output trays as desired.) STPL command causes a page break. File !R! STPL 3; CMNT Two staples on the left; JOBS 0,3,0,0; TEXT - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 353
, 150, 200, 300, 600, or 1200 dots per inch. The 200, 600, and 1200 dpi resolutions are available only for the printing system models that support the 600 or 1200 dpi printing resolution. The default value is 75 dots per inch. The STR command affects only PRESCRIBE raster graphics. It does - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 354
PRESCRIBE Command Reference STRK - STRoKe current path Format STRK; Parameter None Function The STRK command strokes the constructed path onto the current page according to the following current graphics state: • Pen diameter (SPD) • Dash pattern (DPAT) • Fill pattern (FPAT) • Line cap (SCAP) • - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 355
STRK Printout Related Commands FILL, NEWP 345 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 356
PRESCRIBE Command Reference SULP - Set UnderLine Parameters Format SULP distance, thickness; Parameters distance: distance below the baseline thickness: thickness of the underline Function The SULP command sets the thickness of any subsequent underlining as well as the distance below the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 357
SULP Printout 347 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 358
system to optimize the electrical properties (such as the fuser temperature and the transfer bias) so that the best reset for a tray when thickness and print-density parameters are omitted. All trays are reset when all three parameters are omitted. This command is relevant to the FS-1000 printer - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 359
TEXT TEXT - print TEXT Format TEXT ['string'][,option][,U-option]; Parameters string: any character string option: B = Leave cursor at beginning of string E = Move cursor to end of string L = Move cursor down one line N = Move cursor to beginning of next line U-option: Underline text - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 360
PRESCRIBE Command Reference File !R! RES; UNIT C; MAP 2, 2; SFNT 'Univers-MdCd'; TEXT 'Check desired options:', L, U; FONT 2; BOX .1, -.1; TEXT 'Power steering', L; BOX .1, -.1; TEXT 'CD auto changer', L; BOX .1, -.1; TEXT 'Air conditioner', L; PAGE; EXIT; Printout Related Commands CTXT, RTXT - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 361
as 1-byte or 2-byte character code while printing using a text command. To parse such characters, the current font must supports 2-byte characters and a 2-byte symbol set such as Windows 3.1J (19K). The pursing method will automatically be shift JIS encoding (2) if the default font and symbol set is - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 362
the printing system and its configuration. When omitting the tray parameter, 1 is automatically set to the tray parameter. Function The TRSM command instructs printing system to insert blank or printed page between each transparency. The printing system loads transparency from MP tray and inserting - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 363
P = points D = dots Function The UNIT command sets the unit of measurement used in other PRESCRIBE commands. The initial unit is inches. Other supported units of measurement can be calculated as follows: • 1 inch = 2.54 centimeters • 1 inch = 72 points • 1 inch = 300 dots (300 dpi)/600 dots (600 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 364
PRESCRIBE Command Reference Printout 354 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 365
, 400, 450, 480, 600, 720, 800, 900, 1200, 1440, 1800, 2400, 3600, 7200 Function The UOM command applies only to the printing system models that support the 600 dpi resolution. It defines the unit of measurement in dots per inch for cursor movements. The command requires that the UNIT value be - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 366
PRESCRIBE Command Reference Printout Related Command UNIT 356 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 367
's password is required. An error will be displayed on the operator panel if no password or the incorrect password is specified. (See the Technical Reference manual.) Note that if command syntax is incorrect, such as when an alias longer than 31 bytes is specified, the command will be invalid and no - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 368
command. If no virtual mailbox corresponds to the alias given, an error will be displayed on the operator panel. (See the Technical Reference manual.) This command is irrelevant to photocopy virtual mailbox function. Note Files To stack jobs on virtual mailbox number 3: !R! VMOB 3; EXIT; To stack - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 369
will results if the password specification fails or no virtual mailbox corresponds to the alias given. For error displays, see the Technical Reference manual. The master password is valid as the current password for all virtual mailboxes. Virtual mailboxes for which a password has been set are not - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 370
PRESCRIBE Command Reference Files To set 9999 as the password for virtual mailbox number 3 for which no password is set: !R! VMPW 3, 0, 9999; EXIT; To set no password for the virtual mailbox with the alias MyMailbox for which the password 9999 had been set: !R! VMPW "MyMailbox", 9999, 0; EXIT; To - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 371
WIDE WIDE - set WIDE A4 mode Format WIDE mode; Parameter mode: 0 = Off 1 = On Function The wide A4 function widens the A4 printing width in order to prevent unnatural line breaks or clipping of graphics in cases where a document created as a letter-size document is output in A4 size. The WIDE - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 372
PRESCRIBE Command Reference WRED - WRite EnD Format WRED; Parameter None Function The WRED command terminates a sequence of writing data to the memory card or to the hard disk, using one of the commands listed below. The WRED command can be renamed to a string of ASCII characters if necessary. For - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 373
ENDB must follow as a terminator for the barcode data string. Note that carriage return, line feed, space and all other characters must be counted as part of data in the data string field. If data-length is omitted, 0, negative value, or non integer, then data-string is counted all characters until - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 374
PRESCRIBE Command Reference Files !R! XBAR; The Milky Way is a gravitationally bound collection of roughly a hundred billion stars. Our Sun is one of these stars and is located roughly 24,000 light years (or 8000 parsecs) from the center of our the Milky Way. The Galaxy has three major components. - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 375
XBCP 0 XBCP 0 - select barcode type/reset all other XBCP parameters Format XBCP 0[, type]; Parameter type: two dimensional barcode type: 1 = PDF417 (only type currently supported) Function The XBCP 0 command selects a barcode type and resets all parameters to the defaults. File See XBCP 1 ( - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 376
less than 1 dot, truncated to 1 dot. Default is 3 dots. Function PDF417 supports 8 different bar and space widths. The each width is a multiple of 1 to inches;ENDB; MZP 0, 1; XBCP 0; XBAR;Min. element width is reset (to 3 dots);ENDB; EXIT; Printout Minimum element width is 0.02 inch. Default minimum - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 377
percentage; Parameter percentage: value between 0 and 400 Function PDF417 supports an error correction scheme. The XBCP 2 command specifies the the setting of XBCP 2, even if XBCP 2 is executed after XBCP 3, until RES (reset) or XBCP 0. File To set 50% error correction level: !R! RES; XBCP 2, 50 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 378
by predetermined values. An illegal value defaults to 0. Note that the execution of XBCP 3 overrides the setting of XBCP 2 and remains valid until RES (reset) or XBCP 0. File To sets the error correction level to level 4: !R! RES; XBCP 3, 4; XBAR;Error correction can also be set by level;ENDB; EXIT - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 379
XBCP 4 XBCP 4 - set data code word rows Format XBCP 4, number; Parameter number: number of data code word rows, ranging from 3 to 90 Function The XBCP 4 command sets the number of data code word rows in the PDF417 barcode. Illegal values make XBCP 4 ignored. XBCP 6 default provides default. - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 380
PRESCRIBE Command Reference XBCP 5 - set data code word columns Format XBCP 5, number; Parameter number: number of data code word columns, ranges between 1 and 30 inclusive (Illegal values make XBCP 5 ignored.) Function The XBCP 5 command sets the number of data code word columns in the PDF417 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 381
XBCP 6 XBCP 6 - determine aspect ratio of vertical height and horizontal width Format XBCP 6, height, width; Parameters height/width: parts of the aspect ratio of vertical height and horizontal width, ranging between 10: 1 (XBCP 6, 10, 1) and 1: 10 (XBCP 6, 1, 10) Function The XBCP 6 command - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 382
PRESCRIBE Command Reference Printout Aspect ratio is 3:2 in vertical and horizontal directions. Aspect ratio is normal. 372 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 383
XBCP 7 XBCP 7 - determine bar height Format XBCP 7, mod-ratio; Parameter mod-ratio: ratio of module height to element width, ranging from 1 to 10 Function The XBCP 7 command determines the bar height by a ratio to the narrowest element width. An illegal value defaults to 3. File To set the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 384
PRESCRIBE Command Reference XBCP 8 - automatically set rows and columns Format XBCP 8; Parameter None Function The XBCP 8 command permits the system to automatically set rows and columns so that it satisfies the requirement that the multiplication of rows times columns is less than or equal to 928. - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 385
XBCP 9 XBCP 9 - enable truncation Format XBCP 9; Parameter None Function The XBCP 9 command can generate a truncated PDF417 symbol that omits the right row indicator and the stop pattern. Default is non-truncation. 375 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 386
PRESCRIBE Command Reference XBCP 10 - enable file name Format XBCP 10, 'file-name'; Parameter file-name: string containing a file name Function A Macro PDF417 symbol contains an optional file name field. The XBCP 10 command enables this field and defines its contents. The string must be - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 387
XBCP 11 XBCP 11 - enable block count Format XBCP 11; Parameter None Function A Macro PDF417 symbol contains an optional block count field. The XBCP 11 command enables this function. Default is not enabled. The execution of this command also automatically sets Macro PDF417 symbol mode. File !R! RES; - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 388
PRESCRIBE Command Reference XBCP 12 - enable time stamp Format XBCP 12, time; Parameter time: total number of seconds since 00:00:00 AM January 1, 1970 Greenwich mean time Function A Macro PDF417 symbol contains an optional time stamp field. The XBCP 12 command enables this function. The - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 389
XBCP 13 XBCP 13 - enable sender ID Format XBCP 13, 'sender-id'; Parameter sender-id: string containing sender ID Function A Macro PDF417 symbol contains an optional Sender ID field. The XBCP 13 command enables this field and defines its contents. The string must be surrounded by single or - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 390
PRESCRIBE Command Reference XBCP 14 - enable addressee ID Format XBCP 14, 'addressee-id'; Parameter addressee-id: string containing addressee ID Function A Macro PDF417 symbol contains an optional Addressee ID field. The XBCP 14 command enables this field and defines its contents. The string - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 391
XBCP 15 XBCP 15 - enable file size Format XBCP 15; Parameter None Function A Macro PDF417 symbol contains an optional file size field. The XBCP 15 command enables this function. Note that the execution of this command also automatically sets Macro PDF417 symbol mode. This function is disabled in - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 392
PRESCRIBE Command Reference XBCP 16 - enable checksum Format XBCP 16; Parameter None Function A Macro PDF417 symbol contains an optional checksum. The XBCP 16 command enables this function. Note that the execution of this command automatically sets Macro PDF symbol mode. This function is disabled in - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 393
XBCP 17 XBCP 17 - allow control of file ID Format XBCP 17, 'file-id'; Parameter file-id: string containing a file ID Function A Macro PDF417 symbol contains a required file ID. The XBCP 17 command allows control of this field. A random file ID is generated when XBCP 10 through 16 or XBCP 18 are - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 394
PRESCRIBE Command Reference Printout 384 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 395
XBCP 18 XBCP 18 - enable Macro PDF417 symbol mode Format XBCP 18[, block-index]; Parameter block-index: 0 to k-1, and k is the number of blocks Function Executing the XBCP 18 command enables the Macro PDF417 symbol mode. The Macro PDF417 symbol mode directs the reader to separate large data and - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 396
PRESCRIBE Command Reference Printout 386 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 397
the first symbol, X2 , Y2 for third, and so on as measured from the current coordinate (like the MRP command described on the printing system's manual). The remaining pairs of positioning parameters are ignored if there are no more PDF symbol to print. The relative location parameters, Xn and Yn can - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 398
1 File 2 To print 4 30-column-by-20-row PDF symbols at specified locations in Macro PDF mode. In example below, the first line XBCP command resets all XBCP parameters to the defaults and selects the barcode type for PDF417 (though it is the only type currently available); the second line XBCP - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 399
Printout 2 XBCP 19 File 3 To print multiple Macro PDF barcodes beyond the current page. In the example below, the fourth line XBCP 19 has no coordinating parameters specified. This allows the first segment barcode of the ensuing PDF data to be positioned at the current cursor position and the - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 400
PRESCRIBE Command Reference Printout 3 First page Second page 390 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 401
characters can include digits and special symbols such as hyphens. For example, F-1 and GRY-2 are valid buffer names. As the above Format instruction implies, the XBUF command sequence can have two other formats implementing the different functions as follows: XBUF buffer-name,; data-string;ENDB - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 402
PRESCRIBE Command Reference Files is used to delete all buffer name from the printing system memory. ... XBCP 0,1; XBUF PDF 1, 25; This is a PDF417 example. ;ENDB; XBUF PDF 2, 15; This is a test. ;ENDB; ... XBAR PDF 1; MRP 1,1; XBAR PDF 2; The sixth line prints PDF417 barcode containing the data - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 403
command for use by the BLK and ARC commands and in a path. Details for creation of new patterns appear in Chapter 4 of the Technical Reference manual. File !R! RES; UNIT C; MAP 5, 5; XPAT 105;//?//?p@0p@0p@0p@0p@0p@0p@0p@0p@0p@0p@0p@0p@0p@0; PAT 105; BOX 4, 1; BLK 4, 1; PAGE; EXIT - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 404
PRESCRIBE Command Reference 394 - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 405
Index - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 406
, 285 a list as printout, 79 Dashed pattern, 79 Data dump, 218 ending, 93 Destination image, 300 Downloading character, 147 Drawing rule (for fill), 101 Dummy sign (macro), 160 Dumping data, 218 Duplex inhibiting by media type, 162, 163 E EcoPrint, 98 level, 98 e-MPS, 165 limiting values for storage - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 407
value, 110 Filling path, 101 Firmware, 112 initializing, 114 Reprogramming, 112 291 Font list, 105 printing a, 105 Font mode, 119 Fuser mode, 162, 163 G Graphics state, 228, 272 Gray pattern , 297 KIR, 304 refinement level, 304 KPDL, 287 Kyocera Image Refinement, 304 L left, 307 Lightness, 155 Line - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 408
data ending, 96 Registration, 225 Relative position, 80, 82, 167 Resetting the printer by emulation, 220 Resolution, 222 RGB color balance level, 223 gamma path, 176 Starting angle, 28, 182, 199 Status page, 336 user mode and service mode, 336 Symbol set, 65, 129, 226, 268, 294 as a bitmap attribute - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 409
Text parsing, 351 Thickness, 318 TIFF 4.0, 239 Transparency, 299, 352 TrueType, 153, 247 loading ..., 153 Two-dimentional barcode addressee ID, 380 automatic rows and columns, 374 bar height, 373 block count, 377 checksum, 382 data code word columns, 370 data code word rows, 369 error correction - Kyocera FS-1320D | PRESCRIBE Commands Command Reference Manual Rev 4.8 - Page 410
Rev. 4.8 2009.7
Command Reference
PRESCRIBE Commands