Kyocera FS 1920 FS-1920 Installation Guide Rev 1.1
Kyocera FS 1920 - B/W Laser Printer Manual
 |
View all Kyocera FS 1920 manuals
Add to My Manuals
Save this manual to your list of manuals |
Kyocera FS 1920 manual content summary:
- Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 1
FS-1920 Page Printer Installation Guide - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 2
Kyocera Mita Corporation is prohibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copyright notice as the material from which the copying is done. Table of Contents STEP 1 Unpacking 1 STEP 2 Positioning the Printer 2 STEP 3 Installing the Toner - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 3
. List of Shipped Components (A) (B) (for (C) U.S.A. only) (D) (E) (F) Printer Printer Waste Toner Box (E) Toner Container (D) Power Cord (F) CD-ROMs (B) Installation Guide [this booklet] and other printed matter (B) Plastic Bag for Developer Unit (A) Dust Cover (C) [for U.S.A. only] 1 - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 4
printer, resulting in fire. Environment Temperature Humidity 10 to 32.5 °C (50 to 90.5 °F), ideally about 23 °C (73.4 °F) 20 to 80 %, ideally 60 % Do not install the printer fumigate the room, or make liberal use of insecticide, remove the printer first!) • Excessive sunlight or humidity • Lack of - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 5
for the first time, you must prepare it by installing the toner container, waste toner box, and set up the interfacing with the computer. Top Cover 1 Open the printer top cover all the way. Toner Container 10 times or more 2 Take the toner container from the bag. 3 With the label side down - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 6
6 Push firmly on the top of the toner con- tainer at the positions marked PUSH HERE. When the toner container fits into place, it will lock with a clicking sound. 7 Close the top cover. To remove the toner container Lock Lever Pull the lock lever (blue colored) to the right and gently lift the - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 7
4STEP Installing the Waste Toner Box The waste toner box is supplied with the printer. The waste toner box must be installed in the printer. 1 Open the cap of the waste toner box. Cap Waste Toner Box Left Cover 2 Open the left cover on the left side of the printer. 3 Insert the waste toner - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 8
4 Ensuring that it is correctly inserted, close the left cover. To remove the Waste Toner Box While holding the waste toner box, press the lock lever and then gently remove the waste toner box. Lock Lever 6 - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 9
11) or through the option network interface card. Printer Connections Option Serial Interface Board Kit (3.3 V DC) Serial Interface Connector for option sorter (See the option sorter's user's manual.) Printer (Rear) Power Supply Parallel Interface USB Interface Network Option Network Interface - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 10
. Clip Clip Parallel Printer Cable • Use a parallel printer cable that complies with the IEEE1284 standards. • The printer will work best if it is installed near the coputer. The connecting cable should be shielded and not be longer than 3 meters (10 feet). 2 Close the clips on both sides to - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 11
Supply • Install the printer near an AC wall outlet, preferably one that can be used for the printer alone. • Only use this printer with ±10 % at each voltage 60 Hz (120 V) ±2 %, 50/60 Hz (220 to 240V) ±2 % 8.0 A at 120 V, or 3.9 A at 220 to 240 V To Connect the Power Cord • Be sure the printer's - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 12
into the printer on the operator panel (Refer to the Operation Guide [PDF file] provided on the CD-ROM). Standard size paper settings are indicated as fixed positions in the cassette. The following paper weights can be used with the printer the paper guides and paper stopper to the paper - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 13
1 Pull the paper cassette all the way out of the printer. Paper Cassette 2 Push the bottom plate down until it locks. Bottom Plate Standard paper sizes are attached to the inside of the paper cassette as - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 14
size dial is set to OTHER the paper size must be set into the printer on the operator panel. See the Operation Guide (PDF file) provided on the CD-ROM. Paper Size Window 4 Adjust the position of the paper guides located on the left and right sides of the paper cassette. Pull the release lever - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 15
the paper into the paper cassette. Load Limit Load Limit • Do not load more paper than will fit under the load limits on the paper guides. • The paper cassette will hold approximately 500 sheets of paper with a 80 g/m² (21 lb.) basis weight, or with a thickness of 0.11 mm. 7 Set the stack - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 16
is exhausted, the pointer will go down to the level of (empty). 9 If you have installed a paper cassette that can hold the Legal size paper, install the dust cover at the back of the printer. (The Legal size cassette and the dust cover are supplied for U.S.A. only.) Removing the Dust Cover 14 - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 17
the MP tray. Standard paper sizes are attached to the MP tray. For standard paper sizes, slide the guides to the position marked correspondingly. Paper Guides Load Limit 4 Align the paper with the paper guides and insert as far as it will go. Do not load more paper than will fit under the - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 18
To avoid trouble, we recommend that envelopes be delivered face-up using the option rear tray. Refer to next page. Some types of envelopes are not suitable for printing. For details on suitable types of envelopes, see the Operation Guide contained as a PDF file in the CDROM supplied with the printer - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 19
Installing the Option Rear Tray Use the rear tray when you wish paper to be stacked with the printed side facing up (reverse order), or when - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 20
that previous steps were performed properly. When the printer is first switched on after installation, there will be a delay of approximately 8 minutes before the printer gets ready to print as the developer unit needs to be filled with toner. During this period, the message display shows Please - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 21
ENTER key twice. The mes- sage display indicates Processing during printing of the status page, then returns to Ready. If the status page prints correctly, printer setup is complete. For details on using the printer, refer to the Operation Guide contained as a PDF file in the CDROM supplied with the - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 22
Correcting a Paper Jam If a paper jam occurs while you are printing, remove the jammed paper as described below. After you have removed the jammed paper, open and close the top cover or the paper transfer unit. When pulling the paper, pull it gently so as not to tear it. Torn pieces of paper are - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 23
the Printer 1 While pulling the paper transfer unit release lever (green colored), pull out the paper transfer unit. 2 If paper is jammed before the registration roller, remove it as shown in A. If paper is jammed under the registration roller, remove it as shown in B. A Paper Transfer Unit Release - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 24
to this equipment without prior permission, Kyocera Mita as the manufacturer cannot guarantee compliance with FCC rules. To use equipment which does not comply with FCC rules is prohibited. The printer may be optionally installed with the following units: ■ Options Conforming to the Class B limits - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 25
install the printer in a confined area where ventilation is blocked. IMPORTANT SAFEGUARDS 1. Read all of these instructions and save these instructions for later use. 2. Unplug this product from the wall outlet before cleaning on the power cord. Do not locate this product where persons will walk on - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 26
73/23/EEC Manufacturer's name: Kyocera Mita Corporation, Tamaki Plant Manufacturer's address: 704-19 Nojino, Tamaki-Cho, Watarai-Gun, Mie-Ken 519-0497, Japan declares that the product Product name: Page Printer Model number: FS-1920 (as tested with the enhancement optional unit: PF-60, DU-61, and - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 27
of Conformity (U.S.A.) Model Number: Trade Name: Responsible Party: Address: Telephone number: Fax number: Laser Printer FS-1920 (as tested with enhancement optional units: PF-60, DU-61, SO-60.) Kyocera Kyocera Mita America Inc. 225 Sand Road PO Box 40008 Fairfield, New Jersey 07004-0008 - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 28
. If you need to move the printer to another location, remove the toner container, waste toner box, and developer unit. The procedure for removing these is as follows: 1 Remove the toner container and waste toner box from the printer. Put the toner container into the plastic bag in which it was - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 29
make space for the developer unit. 5 Put the developer unit into that space. Developer Unit To reinstall the developer unit into the printer, use the reverse sleep timer function and printer power consumption, refer to the CD-ROM instruction manual provided with the printer. Initial settings of - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 30
a network. Serial lnterface Board Kit (IB-11) Connect to the computer's serial printer port with a serial cable. 4 Envelope Feeder (EF-60) Holds more envelopes at a time than the MP tray. It can be attached to the front of the printer after the MP tray has been removed. 5 Duplexer (DU-61) Performs - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 31
registered mark. This Kyocera Mita page printer uses PeerlessPrintXL to only with the device on which they are installed and transfer possession of the Programs and the device developer of Programs supplied to IBM. IBM's and the developer's limitations of remedies are not cumulative. Such developer - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 32
two years after the cause of action arose. If you acquired the Program in the United States, this license is governed by the laws of the State of New York. information ■ Laser safety This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 33
This page intentionally left blank. - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 34
This page intentionally left blank. - Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 35
- Kyocera FS 1920 | FS-1920 Installation Guide Rev 1.1 - Page 36
operating procedures, see the Operation Guide contained as a PDF file in the CD-ROM supplied with the printer. Ready --- A4 PLAIN . Flashing: Indicates when the printer needs maintenance attention or the printer is warming up (Please wait). Lit: Indicates when a problem or an error occurs that you
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
 |
 |
FS-1920
Page Printer
Installation Guide