Kyocera FS 3800 FS-1800/3800 Installation Manual Rev 1.3

Kyocera FS 3800 - B/W Laser Printer Manual

Get Kyocera FS 3800 - B/W Laser Printer PDF manuals and user guides
UPC - 632983001233
View all Kyocera FS 3800 manuals
Add to My Manuals
Save this manual to your list of manuals

Kyocera FS 3800 manual content summary:

  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 1
    FS-1800/N FS-3800/N Page Printers Installation Manual
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 2
    of Kyocera Mita Corporation is prohibited. Any copies made of all or part of this manual, any copyrightable subject must contain the same copyright notice as the material from which the copying is done. This Installation Manual is applicable to the FS-1800/FS-3800 and the FS-1800N/FS-3800N, which
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 3
    card and the manual for the network interface card are shipped together with the components listed below. (A) (B) (C) (D) (E) Printer Printer Waste Toner Bottle (D) Toner Container (C) Power Cord (E) CD-ROM (B) Installation Manual [this booklet] (B) Plastic Bag for Developer Unit (A)  1 Go to
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 4
    Environment Temperature Humidity 10 to 32.5 °C (50 to 90.5 °F), ideally about 23 °C (73.4 °F) 20 to 80 %, ideally 60 % Do not install the printer where temperature or humidity is outside the recommended range. Print quality may suffer and there will be an increased chance of paper jams. Places to
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 5
    , and set up the interfacing with the computer. Top Cover 1 Open the printer top cover all the way. Toner Container 10 times or more 2 Take the toner container from the bag. 3 With the label side down, thoroughly shake the toner container (in the direction of the arrow) ten times or more to
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 6
    is first switched on after toner installation, there will be a delay of approximately 15 minutes before the printer gets ready to print as the developer unit needs to be filled with toner. To remove the toner container Lock Lever Pull the lock lever (green colored) to the right and gently lift
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 7
    the Waste Toner Bottle The waste toner bottle is supplied with the printer. The waste toner bottle must be installed in the printer. 1 Open the cap of the waste toner bottle. Cap Waste Toner Bottle Side Cover 2 Open the side cover on the left side of the printer. 3 Insert the waste toner bottle
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 8
    4 Ensuring that it is correctly inserted, close the side cover. To remove the Waste Toner Bottle While holding the waste toner bottle, press the lock lever and then gently remove the waste toner bottle. Lock Lever 6
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 9
    interface card. The FS-1800N/FS-3800N have a network interface card already installed at the factory. Printer Connections Printer (Rear) Serial Interface Connector for option sorter (See the option sorter's user's manual.) Parallel Interface Power Supply Network Option Network Interface Card
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 10
    (not included) into the serial interface connector on the rear of the printer. The printer will work best if it is installed near the computer. The connecting cable should be shielded and not be longer than 3 meters (10 feet). Serial Interface Cable 2 Securely tighten the screws on both sides of
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 11
    220 to 240 V (European countries, and the Asia Pacific region), ±10 % at each voltage 60 Hz (120 V) ±2 %, 50/60 Hz (220 to 240 V) ±2 % Max. 7.2 A at 120 V, or max. 3.6 A at 220 to 240 V To Connect the Power Cord • Be sure the printer's power switch is turned off. • Only use the power cord supplied
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 12
    tray Paper weight 60 to 105 g/m² 60 to 200 g/m² The edges of paper are sharp. When loading paper, be careful not to cut your hand on the paper. Paper cassette 1 Pull the paper cassette all the way out of the printer. Paper Cassette 2 Push the bottom plate down until it locks. Bottom Plate 10
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 13
    to use appears in the paper size window. When the paper size dial is set to OTHER (CUSTOM) the paper size must be set into the printer on the operator panel. See the User's Manual (PDF file) provided on the CD-ROM. Paper Size Window 4 Adjust the position of the paper guides located on the left and
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 14
    size. When shipped from the factory, the paper cassette is set to either A4 or Letter size. When using other size paper, move the paper guides and paper stopper all the way out, insert the paper, then adjust the paper guides and paper stopper to the size of the paper. Adjust them so that they are in
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 15
    clips as shown. Clip Clip 8 Insert the paper cassette into the slot in the printer. Push it straight in as far as it will go. There is a paper gauge on the right side of the front of the paper cassette to indicate the remaining paper supply. When paper is exhausted, the pointer will go down to
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 16
    LTR B5 A5 3 Adjust the position of the paper guides on the MP tray. Standard paper sizes are attached to the MP tray. For standard paper sizes, slide the guides to the position marked correspondingly. Paper Guides Load Limit 4 Align the paper with the paper guides and insert as far as it will go
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 17
    trouble, we recommend that envelopes be delivered face-up using the option face-up output tray. Refer to next page. Some types of envelopes are not suitable for printing. For details on suitable types of envelopes, see the User's Manual contained as a PDF file in the CDROM supplied with the printer
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 18
    Option Face-up Output Tray Use the face-up output tray when you wish paper to be stacked with the printed side facing up (reverse order), or when you are printing on envelopes, postcards, transparencies, or thick paper. This face-up output tray is a separate option. Legal Size A4 Size Letter Size
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 19
    installation, there will be a delay of approximately 15 minutes before the printer gets ready to print as the developer unit needs to be filled with toner. During this period, the message display shows Please wait (Adding toner). Ready --- A4 PLAIN 2 Wait until the READY ( ) indicator is also lit
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 20
    the ENTER key twice. The mes- sage display indicates Processing during printing of the status page, then returns to Ready. If the status page prints correctly, printer setup is complete. For details on using the printer, refer to the User's Manual contained as a PDF file in the CD-ROM supplied with
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 21
    Correcting a Paper Jam If a paper jam occurs while you are printing, remove the jammed paper as described below. After you have removed the jammed paper, open and close the top cover or the paper feed unit. When pulling the paper, pull it gently so as not to tear it. Torn pieces of paper are
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 22
    Jam Inside the Printer 1 While pulling the paper feed unit release lever, pull out the paper feed unit. 2 If paper is jammed before the registration roller, remove it as shown in A. If paper is jammed under the registration roller, remove it as shown in B. A Paper Feed Unit Release Lever
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 23
    United States (for the FS-1800/FS-3800) This device complies with Part Kyocera Mita as the manufacturer cannot guarantee compliance with FCC rules. To use equipment which does not comply with FCC rules is prohibited. The printer may be optionally installed with the following units instruction manual,
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 24
    in the United States. Ozone concentration The printers generate printer in a confined area where ventilation is blocked. IMPORTANT SAFEGUARDS 1. Read all of these instructions and save these instructions power cord. Do not locate this product where persons will walk on the cord. 8. If an extension
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 25
    's name: Kyocera Mita Corporation, Tamaki Plant Manufacturer's address: 704-19 Nojino, Tamaki-Cho, Watarai-Gun, Mie-Ken 519-0497, Japan declares that the product Product name: Page Printer Model number: FS-1800/FS-3800/FS-1800N/FS-3800N (as tested with the enhancement optional unit: PF-60
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 26
    Other technical information Kyocera Mita Australia Pty., Ltd. 6-10 Talavera Road, North Ryde, NSW, 2113, Australia Phone: +61 2-9888-9999 Fax: +61 2-9888-9588 Declaration of Conformity (U.S.A.) Model Number: Laser Printer FS-1800/FS-3800 (as tested with enhancement optional units: PF-60, DU
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 27
    cap of the waste toner bottle tightly. 2 Disconnect the connector of the developer unit from the printer and while pulling the developer unit release lever, remove the developer unit from the printer (1). Close the protect cover on the developer unit (2) and put the developer unit into the supplied
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 28
    the CD-ROM instruction manual provided with the printer. Initial settings of the sleep timer function and power saved using the sleep timer function: Initial sleep mode setting Power consumption in sleep mode FS-1800 FS-1800N 15 minutes (15 minutes) 14 W (20 W) 15 W (20 W) FS-3800 FS-3800N 15
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 29
    ing, and mailbox function. Attaches to the top of the printer. Face-up Output Tray 2 This is a face-up tray. It attaches to the rear of the printer. Network Interface Card 3 Enables printing from multiple computers via a network. The FS-1800N/FS3800N have this card already installed at the fac
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 30
    Kyocera Mita page printer uses PeerlessPrintXL to provide the HP LaserJet compatible PCL6 language emulation. PeerlessPrintXL is a trademark of The Peerless Group, Redondo Beach, CA 90278, U.S.A. This product was developed in any form, related in personal property for which IBM is legally liable. 28
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 31
    payment of any taxes, including personal property taxes, resulting from this license. Neither party may bring an action, regardless of form, more than two years after Laser safety This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS)
  • Kyocera FS 3800 | FS-1800/3800 Installation Manual Rev 1.3 - Page 32
    indicates when printing is automatically stopped due to occurrence of an error. Flashing: Indicates data transfer is taking place. Lit: Indicates either that data is being processed, or that data is being written to the memory card. Flashing: Indicates when the printer needs maintenance attention or
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
FS-1800/N
FS-3800/N
Page Printers
Installation Manual