Kyocera FS 9520DN FS-9120DN/9520DN Operation Guide Rev-2

Kyocera FS 9520DN - B/W Laser Printer Manual

Get Kyocera FS 9520DN - B/W Laser Printer PDF manuals and user guides View all Kyocera FS 9520DN manuals
Add to My Manuals
Save this manual to your list of manuals

Kyocera FS 9520DN manual content summary:

  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 1
    FS-9120DN FS-9520DN Page Printer
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 2
    or typographical errors in the present edition. No responsibility is assumed if accidents occur while the user is following the instructions in this guide. No responsibility is assumed for defects in the printer's firmware (contents of its read-only memory). This guide, any copyrightable
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 3
    Programs only with the device on which they are installed and transfer possession of the Programs and the device remedies also applies to any developer of Programs supplied to IBM. IBM's and the developer's Acknowledgement All resident fonts in this printer are licensed from Agfa Corporation.
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 4
    will perform in accordance with Agfa Japan-published specifications, and the diskette will be free from defects Software is free from all bugs, errors or omissions. The parties agree that the Software and Typefaces is repair or replacement of defective parts, upon their return to Agfa Japan. In no
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 5
    3-35 iv 2.2.11 Operating a Memory Card 3-37 2.2.12 Paper Handling 3-41 2.2.13 Other Modes 3-48 Chapter 4 Troubleshooting 4-1 1 General Guide 4-1 2 Print Quality Problems 4-2 3.1 Indicators 4-4 3.2 Maintenance Messages 4-4 3 Indicators and Messages 4-4 3.3 Error Messages 4-6 4 Correcting
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 6
    RS-232C Interface B-3 4.1 PRESCRIBE FRPO D0 command B-4 5 RS-232C Cable Connection B-4 5.1 Obtain a Suitable RS-232C Cable B-4 5.2 Connecting the Printer to the Computer B-4 5.3 Setting the RS-232C Parameters B-5 Appendix C Specifications C-1 Glossary Glossary-1 Index Index-1 CONTENTS v
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 7
    you through topics concerning the operations and maintenance of the printer. Describes how to install and set up the printer driver. This is contained in the latter half of this guide. PRESCRIBE is the native language of the Kyocera Mita printers. This Technical Reference contains the information
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 8
    Caution labels have been attached to the printer at the following locations for safety purposes. BE SUFFICIENTLY CAREFUL to avoid fire or electric shock when removing a paper jam or when replacing toner. Label 2 High temperature inside. Do not touch parts in this area, because there is a danger
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 9
    cold air. •Avoid poorly ventilated locations. •When casters are installed on the printer, moving the printer can cause damage to certain floor surfaces. viii I Power Supply/Grounding the Printer WARNING •Do not use a power supply with a voltage other than that specified. Avoid multiple connections
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 10
    disassemble the printer or its parts as there is a danger of fire, electrical shock or damage to the laser. If the laser beam printer, there is a danger of fire or other trouble. It is therefore recommended that you consult with your service representative in regard to the cleaning of internal parts
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 11
    eyes or touch your mouth with the hands stained with the toner. And make sure not to stick to your skin For the disposal of old toner container and waste toner box, consult your dealer. Or dispose of the toner or toner containers in accordance with Federal, state and Local rules and regulations
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 12
    Chapter 1 Names of Parts A B CDE F 2 Figure 1-1 3 4 1 0 9 8 7 6 5 H G Figure 1-2 L K J I 1-1
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 13
    replacement or when print images become soiled with toner. P Q R E Main charger unit When replacing the toner container, install the grid cleaner to clean the grid. F Cleaning brush Used to clean the internal part of the printer. G Power cord connector H Option unit connector When using the
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 14
    trouble-free printing and reducing wear and tear on the printer printer's performance. A high-quality printer cannot produce high-quality results when the wrong paper is used. Low-priced paper is not economical in the long run if it causes printing problems Table 2-1 Specification Cassette: 60
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 15
    Laser printing is a process involving laser light, electrostatic discharge, toner, and heat. In addition, as the paper passes through the printer paper for manual feed is printer. Uneven paper weight can cause multiple feeds, print defects, poor toner fusing, blurring, and other print quality problems
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 16
    paper can cause feeding problems in the printer. All paper used in the printer should be long grain printer. Printed sheets will then come out flat. Most paper also has a top and bottom surface. Loading instructions paper is electrostatically charged to attract the toner. The paper must be able to
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 17
    printing on adhesive labels is that the adhesive must never come into contact with any part of the printer. Adhesive paper sticking to the drum or rollers will damage the printer. Label paper must be manually fed. Label paper has a structure comprised of three layers, as shown in the figure below
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 18
    for calendars. Recycled Paper Select recycled paper that meets the same specifications as the white bond paper (see 1.2Paper Specifications on page 21) except whiteness. NOTE Before purchasing recycled paper, test a sample on the printer and check that the print quality is satisfactory. Chapter
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 19
    cassette. Inch specifications Each paper cassette can be set to hold paper of any desired size from 11 × 17 to 5-1/2 × 8-1/2". Metric specifications Each paper cassette. Figure 2-5 2 Hold the paper guide and move it to align the paper guide with the required paper width. Paper sizes are marked
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 20
    Type on page 2-5. 1 Open the MP tray. Figure 2-10 5 Set the supplied paper size plate so that the size of the paper loaded can be checked by the insert guides to the size of the paper to be loaded. Figure 2-11 6 Gently push the paper cassette back in. NOTE Before leaving the printer in disuse
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 21
    it will go. 3 Position the envelope against the insert guides with the print side facing upward, and insert it as the wrong orientation or on the wrong side. 4.3 Setting Envelopes When using the optional printer function, envelopes can be set in the MP tray. NOTE Do not print on envelopes wuth
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 22
    Chapter 3 Using the Operator Panel This chapter explains the following topics: • Understanding the Operator Panel • Using the Operator Panel 1. Understanding the Operator Panel The operator panel has an LCD message display, indicators, and eight keys. Operation Indicators (See page 3-2) Message
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 23
    data is being processed, or that data is being written to the memory card. ATTENTION Flashing: Indicates when the printer needs maintenance attention or the printer is warming up (Please wait). Lit: Indicates when a problem or an error occurs that you can clear by yourself. (For example, paper jam
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 24
    * Return Postcard* Custom Size ISO C4 Oficio II Statement Youkei2* 8kai* 16kai* Table 3-3 * With only the MP tray feeding NOTE While the printer is processing data, the SIZE display indicates the paper size selected by the application software. Chapter 3 Using the Operator Panel 1.5 Paper Type
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 25
    Option (appears only when an option network interface card is installed) Serial 3 Select the interface to cancel using the or error. • Used to select the emulation, font, character code set; to read a memory card, and more. • When pressed during mode selection, terminates the setting and the printer
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 26
    copies to print, emulation, etc., to your specific needs. Settings can be made when Ready is indicated on the printer message display. The printer obeys the most recently received printer settings sent from the application software, or from the printer driver, which take priority over operator panel
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 27
    Chapter 3 Using the Operator Panel Continued Interface > Parallel Interface > USB Interface > Serial Interface > Network Interface > Option Continued on the next page >Parallel I/F Auto >Baud rate 9600 >Data Bits 8 >Data Bits 7 >Stop Bits 1 >Stop Bits 2 >Parity None >Protocol DTR (
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 28
    Emulation IBM Printer Emulation DIABLO US Emulation EPSON LQ-850 Font > >KC-GL > Pen Width >KC-GL Page Set [SPSZ] >Print KPDL Errs Off >Print KPDL Errs Off >Alt. Emulation PCL 6 >Font Select > Internal >Font Select > Option Page Set > Continued on the next page >Code Set IBM PC-8 >List
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 29
    Chapter 3 Using the Operator Panel Continued Print Quality > Opt. ROM > Hard Disk > RAM DISK Mode Off RAM DISK Mode > On Memory Card > Continued on the next page >KIR Mode On >KIR Mode Off >EcoPrint Mode Off >EcoPrint Mode On >Resolution Fast 1200 mode >Print Density 03 >
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 30
    Continued Paper Handling > >MP Tray Mode Cassette >MP Tray Mode First >MP Tray Size A4 >MP Tray Type Plain >Cassette1 Size > >Cassette 1 Type Plain >Feed Select Cassette 1 >Duplex Mode None >Stack Selects Top tray FaceDn >Stitch Adjust > Continued on the next page >Override A4/LT Off >Override A4
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 31
    > >Total Print 0123456 >New Toner Installed >MSG Language English >Form Feed Time Out 015sec. >Sleep Timer > 015 min. >Print HEX-DUMP >Printer Reset >Resource Prot. Off >Buzzer On >Buzzer Off >Auto Continue > Mode Off >Auto Continue > Mode On >Finishing > Error >Service > >>Sleep Mode On
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 32
    activated by the MENU key while the printer is Ready. 2.2.1 Printing the Menu Map The printer prints a full list of menu selections. Firmware Version: Released: 1 Hardware Information Memory 2 3 Page Information 4 Network Status 6 Interfaces Installed Options Emulation Error Log Toner
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 33
    (PostScript) errors • Memory card errors • Memory card, hard disk, RAM disk errors The most recent error is displayed on the top line of the Error Log. For error remedies, see Maintenance Messages on page 4-4. Error information is cleared when the printer's power is turned off. 9 Toner Gauge This
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 34
    appropriate radio button on the printer driver when printing from a computer. Virtual Mailbox Virtual mailbox is part of Job Storage, which number of copies from the printer operator panel. To print a job as a quick copy job, see Printer Driver Guide. The default number of print jobs that can
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 35
    code must be entered on the operator panel to print a stored job. Print data will be stored in the hard disk/RAM disk after printing. See KX Printer Drivers Operation Guide for the driver Print will be automatically deleted if you turn the power off after printing, but jobs saved using Stored Job
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 36
    Printing a code job Install the KM-NET Job Manager software from the CDROM supplied with the printer. To do this, from the CDROM Main Menu, select Printer Utilities > Install KM-NET Job Manager. 1 Browse through Windows Start > Programs > KYOCERA MITA > KM-Net > Job Manager. 2 Enter the password for
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 37
    Data Tray001: If you have named the virtual mailbox with an alias on the printer driver, the alias (Richard, in this example) will follow the number: >Print Hold jobs • Maximum space assigned to temporary code jobs • Maximum space assigned to permanent code jobs • Maximum space assigned to virtual
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 38
    code jobs. You can change the maximum space from 0 to 9999 (megabytes). The actual maximum size depends on the size of free hard disk space, however. The default 50 MB. For example, if the total hard disk space is 3.2 GB, the default size is 500 MB. 1 Press the MENU key. 2 Press the or key
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 39
    code jobs. You can change the maximum space from 0 to 9999 (megabytes). The actual maximum size depends on the size of free hard disk space, however. The default of 50 MB. For example, if the total hard disk space is 3.2 GB, the default size is 500 MB. 1 Press the MENU key. 2 Press the or key until
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 40
    The parallel interface supports a bi-directional/high-speed mode according to IEEE standards. Normally, this interface is used under the default setting Auto. For details, see Appendix B Host Computer Interface. After setting the interface, be sure to reset the printer or turn the power off at least
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 41
    communication problems occur, lower the baud rate. 9 Display the desired baud rate and press the ENTER key. 10 Press the MENU key. The message display returns to Ready. Changing Network Interface Parameters This printer supports TCP/IP, NetWare and EtherTalk protocols. In addition, you can install
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 42
    interface status page shows the firmware version, the network addresses, and other information under various network protocols about the network interface. The default setting is On (print). The network interface status page will be printed out after the printer status page. NOTE Printing out
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 43
    key repeatedly until Emulation appears. One of the emulation names shown below appears, indicating the current emulation. PCL 6 (default) KC-GL KPDL KPDL (AUTO) Line Printer IBM Proprinter DIABLO 630 EPSON LQ-850 3 Press the ENTER key. A blinking question mark (?) appears. Emulation ?PCL 6 4 Press
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 44
    key. The message display returns to Ready. Auto Printing of KPDL Error The printer can be set to print error data during KPDL emulation. If this is set to On, error data will be printed only when trouble occurs during printing. The factory default setting is Off. 1 Press the MENU key. 2 Press the or
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 45
    the paper size specified by the PRESCRIBE SPSZ command. For details, see Programming Manual in the CD-ROM. 13 Press the ENTER key to set the page fonts that are downloaded to the printer memory, or fonts stored on a memory card, hard disk, or option ROM, can be selected as the default font. In this
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 46
    fonts are installed in the printer. 4 Press the key. >> I000 The letter before the number indicates the type of font as follows: Letter I S M H O Table 3-8 Description Internal fonts Soft (down load) fonts Fonts in an option memory size of the default font. If the default font is a
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 47
    key. 9 Press the MENU key. The message display returns to Ready. Setting the character code set You can change the character code set. Available character code sets vary depending on the current font. (The default character code set is IBM PC-8.) 1 Press the MENU key. 2 Press the or key repeatedly
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 48
    key until the desired character code set appears. 7 Press Press the ENTER key again. Processing appears, then Ready. The printer prints a list of fonts with a short sample and font ID and Bitmapped Fonts List PRESCRIBE Font Name Scalable/Bitmap Password Selection [FSET] Font ID 3 Press the key
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 49
    Chapter 3 Using the Operator Panel 5 Press the ENTER key. A blinking cursor ( _ ) appears. >Copies 001 6 Press the or key to increase or decrease the value of the figure where the cursor is blinking. It can be set between 1 and 999. You can use the and keys to move the cursor right and left. 7 When
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 50
    display returns to Ready. Page Protect Mode Although Auto is the default setting and this menu does not usually appear, Page Protect will be forcibly set to On if a Print overrun Press GO error occurs due to insufficient printer memory. Be sure to return this setting to Auto in order to maintain
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 51
    Carriage-Return (CR) Action This procedure instructs the printer what to do when it receives a carriage-return code (character code 0DH). 1 Press the MENU key A carriage-return is performed. (Default) A carriage-return and linefeed are performed. The carriage-return code is ignored. 7 When the
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 52
    for increasing printout quality; EcoPrint, a printing mode that reduces toner consumption during printing; printing resolution; and Adjustment of Print Density. KIR (Kyocera Image Refinement) This printer incorporates the KIR (Kyocera Image Refinement) smoothing function. At a resolution of 600 dpi
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 53
    key. The message display returns to Ready. Resolution You can set the default print resolution in three ways: 300 dpi, 600 dpi and Fast 1200 mode an Option Hard Disk By installing the option hard disk into the printer, the e-MPS function can be used. The printer's menu selection system allows you
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 54
    writes file to the hard disk and instructs the printer to automatically print out a hard disk the written data on the memory hard disk. Others: Error information. When the hard disk completed successfully, an error code appears on the message display. For details, see Error Messages on page
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 55
    . The message display returns to Ready. 3-34 Printing a List of Data Names The printer prints a list of all data names (referred to as partitions) stored in a hard data, including the amount of memory that the printer uses for its system. Partition Name: The name of the written
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 56
    maximum RAM disk size can be calculated as follows: FS-9120DN: Maximum RAM size = Total printer memory minus 36 MB FS-9520DN: Maximum RAM size = Total printer memory minus 24 MB For example, if the total memory installed in your printer (FS-9520DN) is 64 MB (Default), you can set 40 MB of RAM disk
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 57
    writes the file to the RAM disk and instructs the printer to automatically print out a RAM disk write of the written data on the memory card. Others: Error information. When the RAM disk completed successfully, an error code appears on the message display. For details, see Error Messages on page
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 58
    3-16 See Printing a List of Data Names on page 3-34 for details on device information. 2.2.11 Operating a Memory Card The printer is equipped with a slot for a memory card. By inserting a memory card into the printer, the following operations become available. For details about the handling of the
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 59
    is turned on, the fonts are automatically read into the printer. To re-read fonts into the printer from a memory card, proceed as follows. 1 Press the MENU key. 2 Press the or key repeatedly until Memory Card > appears. Memory Card > 3 Press the key. 4 Press the or key repeatedly until >Read Fonts
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 60
    that the message display has changed to Waiting, then press the GO key. This writes the file to the memory card and instructs the printer to automatically print out a memory card write information page as shown below. WRITE INFORMATION Figure 3-17 Partition Type: Type of data written (currently
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 61
    the following items; Capacity: Used Space: Free Space: The total size of the memory card. The space the printer uses for its system. The space remaining in the memory card for storing data. When the memory card format information is printed, the message display returns to Ready. 3-40 PARTITION
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 62
    printer. Partition Size: The size of the written data in bytes. Partition Type: The type of the written data i.e., whether it is host data (Data) or font data (Font). When the list of file names (partition list) for the memory Manual Feeding) The printer the application (printer driver). The
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 63
    returns to Ready. Setting the MP Tray Type You can automatically select the paper cassette according to the selection made by the application (printer driver). The factory default setting is Plain. For more details about the paper types that can be fed from the MP tray, see Paper Size Unit Selection
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 64
    paper feeder (PF-70) is installed. •Cassette3 Size > appears when an option paper feeder (PF-75) is installed. If option paper feeders are using the media type selection function from the application (printer driver). The factory default setting is Plain. For more details about the paper types
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 65
    to Ready. Setting Duplex Printing Using the duplex unit, you can automatically print on both sides of the paper. The duplex unit is installed underneath the printer. Binding Setups The term binding refers to the manner in which printed pages of paper are joined together (by gluing, stitching, etc
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 66
    Output Device You can select whether printouts will be received by the printer's top tray (face-down) or to the optional document finisher's output Positions When installing the option document finisher DF-75, adjust the stitch positions using the following procedures. In the default settings, the
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 67
    between A4 size and Letter size. Under the default setting of Off, the paper size of the formatting the jobs. If these differ, a corresponding error message is displayed. When this is set to printer. Eight custom user settings may be registered. After having been set, any of these may be called up
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 68
    paper thickness. The display changes as shown below. For details of the default setting for each paper type, see Paper Type on page 2-5. Light Normal can set whether or not to enable duplex printing as follows. The default setting is Enable. 1 Display the custom paper type (see Customizing Paper
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 69
    page. Note that if this operation is performed when the toner container is not replaced, the toner gauge measurement will not be indicated correctly. Also refer to the Installation Guide supplied with the toner kit when replacing the toner container. 1 Press the MENU key. 2 Press the or key
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 70
    4 Press the or key repeatedly until >Form Feed Time Out appears. The default setting is 30 seconds. >Form Feed Time Out 030sec. 5 Press the ENTER returns to Ready. Sleep Timer Setting The printer has a sleep timer to conserve power when the printer is not printing, processing, or receiving data
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 71
    Panel 4 Press the or key repeatedly until >Sleep Timer > appears. The default setting is 015 min. >Sleep timer > 015 min. 5 Press the ENTER Received Data Dumping It is possible to print data received by the printer as hexadecimal code for the purposes of debugging programs and files. 1 Press the MENU
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 72
    Press the GO key to finish printing. Printer Resetting The procedure described below resets the printer's temporary conditions, such as the current unit of measurement, page orientation, font, character code set, margins, etc., set by commands to their default values. 1 Press the MENU key. 2 Press
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 73
    Auto Continue Setting When Auto Continue is enabled, the printer will automatically print the next received data following a preset amount of time passes after any one of the following errors occurs: Memory overflow Press GO Print overrun Press GO KPDL error Press GO File not found Press GO RAM disk
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 74
    the optional finisher is installed on the printer. Duplex Printing Error Detection Setting This setting controls whether or not the message Duplex disabled Press GO appears when label or some other type of paper that is not supported
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 75
    , press the MENU key. Punch Error Detection Setting This setting is possible only when the Punch Unit is installed on the optional finisher unit. This Print Status Page menus. Printing the Service Status Page The service status page contains printer settings information that is more detailed than
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 76
    >>Print Status Page ? 8 Press the ENTER key. The message display indicates Processing and printing starts. NETWORK STATUS PAGE FS-9520DN Page 1 of 4 Chapter 3 Using the Operator Panel Figure 3-22 NOTE The network interface status page will be printed after the printer service status page. 3-55
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 77
    Chapter 4 Troubleshooting This chapter explains how to handle printer problems that may occur. If a problem cannot be corrected, contact your Kyocera Mita dealer. This chapter explains the following topics: • General Guide • Print Quality Problems • Indicators and Messages • Correcting a Paper Jam
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 78
    as blank output. The troubleshooting procedure for each type of problem is explained below. If you still cannot solve the problem, contact your Kyocera Mita dealer. Printed Results Completely blank printout Corrective Action Check the toner container. Open the printer front cover and check that
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 79
    . Open the printer left cover 1 and check the transfer roller. If the transfer roller is dirty with toner, try printing several pages. Transfer Roller Check the file or program. Check whether the problem is being caused by a PRESCRIBE command error. If the problem occurs only with a specific file or
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 80
    power cord, and contact your Kyocera Mita dealer. Message Add paper (paper source) Add staples Call service ####:0123456 Call service F###: Chad box full Check chad box Press GO Clean printer Press GO Close finisher cover Close front cover Table 4-4 Corrective Action The paper has run out. Supply
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 81
    installed in the wrong slot. Turn off the printer and reinstalled in the correct slot. The maintenance kit (MK-702 for FS-9120DN, MK-703 for FS-9520DN) needs to be replaced. Replace the maintenance kit since the total number of printed pages has reached 500,000. Call for service. The maintenance
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 82
    CHAPTER 4 TROUBLESHOOTING Message Replace toner Clean printer Replace waste toner box Toner low Top tray paper full Warning image adapt Warning Low memory Table 4-4 (Continued) Corrective Action Replace the toner container using a new toner kit. The printer does not operate when this message is
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 83
    operator panel. Look at the error code given in place of ## and refer to the corresponding description given below. 01: The memory card does not meet specifications. This memory card cannot be used by this printer. Insert a memory card which can be used by this printer. (See Memory Card (CF) on page
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 84
    4 TROUBLESHOOTING Paper installing the paper feeder PF-70, "3" appears with upper cassette, while "4" with lower cassette. Remove the paper jammed in the paper stacker. (For details, see the operation guide problem by changing the paper, there may be a problem with the printer. Contact your service
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 85
    Chapter 4 Troubleshooting 4.1 Jam in Paper Cassette The following procedure also applies taking care not to tear it. If the paper has been torn, remove all the scraps from the inside the printer. Figure 4-4 4.3 Jam inside the MP transport 1 Pull up the lock lever and open left cover 1. Figure 4-2
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 86
    the duplex unit and remove the jammed paper. CHAPTER 4 TROUBLESHOOTING 6 Open left cover 1 to remove paper jammed in the MP transport tray. NOTE When removing jammed paper, be careful not to touch the printer drum. This can cause printer malfunction. Figure 4-7 4 Open the front cover. Figure 4-10
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 87
    Chapter 4 Troubleshooting 9 If the paper has been torn, remove the MP transport tray. CAUTION •Take care not to leave any small pieces of paper in the printer when removing paper jams as this may result in fire. •The printer's fixing unit is extremely hot. Take sufficient care when working in this
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 88
    4.5 Jam in Left Cover 2 1 Open left cover 2. CHAPTER 4 TROUBLESHOOTING Figure 4-20 2 Remove the jammed paper. Figure 4-21 3 Close left cover 2. 4.6 Paper Jam at the Option Document Finisher Paper is jammed at the option document
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 89
    waste toner box) Installation Guide NOTE • Be sure to distance items such as floppy disks during toner container replacement. • Be sure to clean the inside of the printer when replacing the toner container. • Use of original Kyocera Mita toner kits is highly recommended to prevent printer trouble
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 90
    the lock lever up again and gently lift the toner container. Chapter 5 Maintenance 7 Grasp the handle on the toner container and insert the toner container along the rail of the printer. Figure 5-3 4 Seal up the old toner container with the supplied plastic bag and dispose of it. Figure 5-7 When
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 91
    5 Maintenance 10 Remove the seal from the rear of the old waste toner box, and then close the opening of the box with the seal. Seal up the old waste toner box with the supplied plastic , remove the grid cleaner from the printer and dispose of it. The grid cleaner is not re-usable. 15 Fit the new
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 92
    16 Remove the blue colored cleaning brush. Chapter 5 Maintenance 19 Replacing of toner and cleaning of the internal parts of the printer are completed. Close the front cover and the left cover 1. Allow approximately five minutes before using the printer until the main charger unit has dried up.
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 93
    details on the code sets, read the PRESCRIBE Commands Technical Reference on the supplied Kyocera Mita Document Library CD-ROM), spacing, pitch, height, style, stroke weight, and typeface family. List of Fonts This section contains a full list of the printer's internal fonts. The printer has 80 PCL
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 94
    I PCL (Scalable and Bitmap) Fonts Chapter 6 Fonts 6-2
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 95
    Chapter 6 Fonts I KPDL Fonts (1) 6-3
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 96
    I KPDL Fonts (2) Chapter 6 Fonts 6-4
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 97
    ) on the main circuit board. Expanded printer memory enables you to print more complex pages, download more fonts, and define more macros. 1. Available Options The printer has the following options available. For instructions on installing individual options, refer to the documentation included
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 98
    printer, the network interface card supports TCP/IP, IPX/ SPX, NetBEUI and EtherTalk protocols, so that the printer can be used on network environments including Windows Also provides a punch function. They are installed to the left side of the printer. DF-73 Document Finisher Provides finishing
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 99
    PF-70 or PF-75 Paper Feeder can be installed below the printer. PF-70 Paper Feeder holds approximately 500 sheets of A4 to A3 (11 × 17" in Ledger) size paper. 2.3 Network Interface The FS-9120DN/FS-9520DN have the standard Network interface. This printer supports the TCP/IP, IPX/SPX, NetBEUI, and
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 100
    of the printer. If a hard disk unit is installed in the printer, received memory when printer is turned on. For details of available memory cards, see your dealer. 1 Turn off the printer. NOTE Do not insert or remove a memory card while the power is on. If the memory card is removed while the printer
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 101
    by a Kyocera Mita authorized dealer or Kyocera Mita certified technician. Kyocera Mita shall not be liable for damage due to improper installation of the expansion memory. The following instructions are intended for the technician only. 3.2 Removing the Main Circuit Board from the Printer Remove
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 102
    4. Installing DIMMs I DIMMs to be used See your Kyocera Mita dealer for purchasing information of the DIMMs that are best suited for use with this printer. 32 MB, 64 MB, 128 MB and 256 MB DIMMs can be used for memory expansion. Insert the DIMM into the socket as shown below. 1 Remove the DIMM from
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 103
    specifications, and voltage levels. For details on the network interface, refer to the IB-21E/IB-22 User's Manual contained on the CD-ROM that is supplied with the printer Ignored [nInit] Error*, returns error status if FRPO O2=2 [nFault] Not connected Not connected Power Ready Ignored [nSelectIn]
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 104
    NOTE The Paper Empty, Online, and Error signals are not used unless enabled by the FRPO command (O2 parameter). Appendix B Host Computer Interface 2. USB Interface This printer supports the Hi-Speed USB 2.0. USB (Universal Serial Bus) interface specifications and interface signals are as follows
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 105
    or outgoing with respect to the printer. Pin 1 2 3 4 signals conform to EIA RS232C specifications. SPACE is from 3 volts and their identification codes are given below default setting is 9600 baud. H2: Data bits 7 or 8; the factory default setting is 8. H3: Stop bits 1 or 2; the factory default
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 106
    Ready or Waiting Serial interface error Error Error not resolved resolved XON sent every 3 to 5 seconds D0=0 (default) D0=1 XON not sent plastic cover back on. 5.2 Connecting the Printer to the Computer Check that the power of both the printer and the computer is switched off. 1 Discharge
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 107
    values listed above. 7 Set the computer to the same parameters as the printer. On many computers this can be done by setting DIP switches before the power is turned on. Another method is as follows: 5.3 Setting the RS-232C Parameters Windows XP, proceed as follows: 1 Click on the Start button in the
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 108
    5 The Properties sheet is displayed for the selected COM port. Click on the Port Settings tab and set the port properties. Appendix B Host Computer Interface Figure B-4 6 After setting the properties, click the OK button. I DOS 1 Enter the following commands: C:\>MODE COM1:96,N,8,1,P C:\>MODE LPT1
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 109
    time Controller Main memory Operating system Interfaces Memory card slot Self test Maximum duty cycle Drum Developer Main charger Transferring Separation Drum cleaning Drum discharging Fuser Toner saving Paper Table C-1 C-1 Description FS-9120DN Electrophotography, laser scan FS-9520DN A4/Letter
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 110
    APPENDIX C SPECIFICATIONS Item Paper feed trays Description FS-9120DN FS-9520DN Cassette : A5 to A3/Ledger size universal cassette. % Max. allowable frequency fluctuation:±2 % Max. allowable frequency fluctuation:±2 % Power consumption Max.: 1,400 W During printing: 850 W (U.S.A./Canada) 920 W
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 111
    with the Kyocera Mita FS series. You can view information for printers connected to the network using SNMP commands. KM-NET VIEWER is contained on the Kyocera Mita Software Library CD-ROM supplied with the printer. MB (mega byte) This unit is used to express data quantities and memory capacities
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 112
    using application software. The printer driver for the printer is on the Kyocera Mita Software Library CD-ROM supplied with the printer. Install the printer driver on the computer connected to the printer. RAM disk This is a virtual disk drive that uses part of the printer's memory. With RAM disk
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 113
    47 Binding 3-44 E EcoPrint 3-31, Glossary-1 e-MPS 3-12, 3-16 Code jobs 3-15 Private job 3-14 Proof-and-hold 3-14 Quick copy 3-13 Virtual mailbox 3-16 Emulation 3-22, Glossary-1 Envelopes 2-5, 2-8 Error messages 4-6 Expansion memory A-1, Glossary-1 Index-1 F Font 3-24, 6-1 Font list 3-27, 6-1 Front
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 114
    , Glossary-1 Paper guide 2-6 MP transport quality 3-31, 4-2 Printer driver 3-12, Glossary-2 Protocol Specifications 2-1, C-1 Status page 3-11, 3-21, 3-54, Glossary-2 Stitch position 3-45 T TK-70 5-1 Toner container 1-2, 3-12, 5-1 Toner kit 5-1 Top tray 1-2, 3-45 Transfer roller 4-3 Troubleshooting
  • Kyocera FS 9520DN | FS-9120DN/9520DN Operation Guide Rev-2 - Page 115
    ©2004 is a trademark of Kyocera Corporation 2004. 1 Rev.2.0
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
FS-9120DN
FS-9520DN
Page Printer