Home » Kyocera Manuals » Multifunction Devices » Kyocera KM-8030 » Manual Viewer

Kyocera KM-8030 PRESCRIBE Commands Technical Reference Manual - Rev. 4.7 - Page 101

Permanent Parameters - service mode

Get Kyocera KM-8030 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Chapter 6 Permanent Parameters The printing system maintains a number of parameters in a non-volatile (flash) memory. These parameters control the initial state of the environment at power-up, including the initial emulation mode, page orientation, character set, buffer allocations in memory, interface parameters, and other options. The parameters may be changed permanently with the FRPO (Firmware RePrOgram) command. Some FRPO parameters affect only the current interface (interface-dependent) and some affect all interfaces at once (non-interface-dependent). If the printing system is shared with other users, remember that any changes to any non-interfacedependent parameters may interfere with the print jobs of the other users. This chapter explains the FRPO command and gives examples of its use. The current settings of the FRPO parameters are listed as option values on the printing system's service status page. Refer to the tables in this chapter to interpret the values. To print a service status page, command: !R! STAT 1; EXIT; Before changing any FRPO parameter, print out a service status page, so you will know the parameter values before the changes are made. To return FRPO parameters to their factory default values, send the FRPO INIT (FRPO-INITialize) command.

Section	Page
General Infomation	3
Introduction	5
About the Technical Reference manual	6
Table of Contents	7
Introduction to PRESCRIBE	9
Format of PRESCRIBE Commands	12
Basic Concepts	12
Edge Limits	12
Margins	12
Page Orientation and Direction	13
Coordinate Systems	15
Text Positioning	15
Character Spacing	16
Paths	17
Logical Page and Physical Page	17
Command Parameters	18
Numeric Parameters	18
Character Strings	19
Upper and Lowercase Letters	20
Special Parameters	21
Graphics Tutorial	23
Drawing Lines	24
Drawing Boxes and Circles	28
Drawing Filled Shapes	31
Drawing Pie Charts	36
Path Mode Graphics	38
Path	38
Drawing Lines	40
Miter Limit	43
Dash Type	44
Drawing Arcs and Curves	46
Drawing Complex Curves	48
Closed Paths	51
Filled Areas	52
Clipping Rectangle	54
Printing with Character Paths	55
Raster Graphics	56
Raster Data Compression Formats	56
Commands for Printing Raster Data	57
Printing Raster Data	59
Changing the Printing System’s Imaging Model	59
Saving and Restoring the Graphics State	61
Macros	63
Examples of Macros	65
Fonts	69
List of Fonts	70
KPDL Fonts	72
Substituting a Bitmap Font	74
Font Selection	75
Font Selection by PRESCRIBE Commands	75
Placement of Font Commands	79
Creation of New Symbols and Characters	80
Symbol Set	81
International Characters	82
Selecting HP Symbol Sets	82
Barcodes	85
PDF417 Symbol Description	94
Printing a Two-dimensional Barcode	96
Limitations of Two-dimensional Barcode	97
Macro PDF417	98
Creating a Macro PDF 417 Representation	98
Permanent Parameters	101
Interface-dependent Parameters	102
Interface-independent Parameters	105
Emulation	113
Automatic emulation sensing	115
General Information on Emulation	115
Line Printer Emulation (Mode 0)	115
IBM Proprinter X24E Emulation (Mode 1)	116
IBM Proprinter X24E Control Codes	118
IBM Symbol Sets	121
Diablo 630 Emulation (Mode 2)	124
Diablo 630 Control Codes	126
Diablo 630 Symbol Sets	128
Epson LQ-850 Emulation (Mode 5)	133
EPSON LQ-850 Control Codes	136
LQ-850 Symbol Sets	138
HP LaserJet Emulation (Mode 6)	145
LaserJet Fonts	147
LaserJet Symbol Sets	149
Resource Protection	152
Switching the Print Resolution	154
HP LaserJet Reset State	155
LaserJet PJL	155
HP LaserJet Printer Commands - PCL	161
HP-GL/2 Context Printer Commands	176
PJL Syntax Comparison	178
LaserJet Symbol Sets	179
HP 7550A Emulation [KC-GL] (Mode 8)	208
Basic	208
KC-GL Environment Options	209
Plotter Status Information	214
Device-Control Instructions	218
Fonts and Symbol Sets in KC-GL	219
KC-GL Symbol Sets	220
KC-GL Limits	222
Summary of KC-GL Instructions	223
KPDL Operators	227
Communication with the Printing System	227
KPDL Summary	228
KPDL Error Messages	251
KPDL Printable Area	252
Index	255
Numerics	255
A	255
B	255
C	255
D	255
E	255
F	256
G	256
H	256
I	256
K	256
L	256
M	256
N	256
O	257
P	257
Q	257
R	257
S	257
T	257
U	257
W	257
X	257

Match case Limit results 1 per page

Chapter 6

Permanent Parameters

The printing system maintains a number of parameters in a non-volatile (flash) memory.

These parameters control the initial state of the environment at power-up, including the

initial emulation mode, page orientation, character set, buffer allocations in memory,

interface parameters, and other options.

The parameters may be changed permanently with the FRPO (Firmware RePrOgram)

command. Some FRPO parameters affect only the current interface (interface-depen-

dent) and some affect all interfaces at once (non-interface-dependent). If the printing sys-

tem is shared with other users, remember that any changes to any non-interface-

dependent parameters may interfere with the print jobs of the other users. This chapter

explains the FRPO command and gives examples of its use.

The current settings of the FRPO parameters are listed as option values on the printing

system’s service status page. Refer to the tables in this chapter to interpret the values. To

print a service status page, command:

!R! STAT 1; EXIT;

Before changing any FRPO parameter, print out a service status page, so you will know

the parameter values before the changes are made. To return FRPO parameters to their

factory default values, send the FRPO INIT (FRPO-INITialize) command.