Kyocera KM-8030 PRESCRIBE Commands Technical Reference Manual - Rev. 4.7 - Page 111

Table 6.2. Interface-independent Parameters (Sheet 7 of 7) Environment Parameter Value Factory setting Error message for Y3 device error 0: Does not display an error message and pause 0 the job when the device error occurs. 1: Displays an error message when duplex printing is not executed because of a possible limitation. 2: Displays an error message and pause the job when running out of staples. 3: Combination of value 1 and 2. 4: Displays an error message and pause the job when the waste punch box is full. 5: Combination of value 1 and 4. 6: Combination of value 2 and 4. 7: Combination of value 1, 2 and 4. 8: Displays an error message and pause the job when the maximum number of stapling is exceeded. 9: Combination of value 1 and 8. 10: Combination of value 2 and 8. 11: Combination of value 1, 2 and 8. 12: Combination of value 4 and 8. 13: Combination of value 1, 4 and 8. 14: Combination of value 2, 4 and 8. 15: Combination of value 1, 2, 4 and 8. 16: Displays an error message when stapling, puching, offset or rotate collate is not executed because of a possible limitation except 2, 4 and 8. 17: Combination of value 1 and 16. 18: Combination of value 2 and 16. 19: Combination of value 1, 2 and 16. 20: Combination of value 4 and 16. 21: Combination of value 1, 4 and 16. 22: Combination of value 2, 4 and 16. 23: Combination of value 1, 2, 4 and 16. 24: Combination of value 8 and 16. 25: Combination of value 1, 8 and 16. 26: Combination of value 2, 8 and 16. 27: Combination of value 1, 2, 8 and 16. 28: Combination of value 4, 8 and 16. 29: Combination of value 1, 4, 8 and 16. 30: Combination of value 2, 4, 8 and 16. 31: Combination of value 1, 2, 4, 8 and 16. Duplex operation for Y4 specified paper type (Prepunched, Preprinted and Letterhead) 0: Leaves the job as is when the job which the 0 specified paper type is specified in simplex mode. 1: Adds blank pages and prints the job in duplex mode when the job which the specified paper type is specified in simplex mode. Default operation for Y5 PDF direct printing 0: Enlarges or reduces the image to fit in the 0 current paper size. Loads paper from the current paper cassette. 1: Through the image. Loads paper which is the same size as the image. 2: Enlarges or reduces the image to fit in the current paper size. Loads Letter, A4 or A3 size paper depending on the image size. 3: Through the image. Loads Letter, A4 or A3 size paper depending on the image size. 8: Through the image. Loads paper from the current paper cassette. 9: Through the image. Loads Letter, Ledger or Legal size paper depending on the image size. 10: Enlarges or reduces the image to fit in the current paper size. Loads Letter, Ledger or Legal size paper depending on the image size. e-MPS error Y6 0: Does not print the error report and display 3 the error message. 1: Prints the error report. 2: Displays the error message. 3: Prints the error report and displays the error message. a Supported only by FS-1500 series, FS-1600 series, FS-3400 series, and FS-3600 series. 6-11