Kyocera KR2 Modem Setup

Kyocera KR2 - Mobile Router Wireless Manual

Get Kyocera KR2 - Mobile Router Wireless PDF manuals and user guides
UPC - 674847025085
View all Kyocera KR2 manuals
Add to My Manuals
Save this manual to your list of manuals

Kyocera KR2 manual content summary:

  • Kyocera KR2 | Modem Setup - Page 1
    
into
the
back
of
the
router
and
then
into
a
wall
outlet.
 5. Start
your
computer.
 6. Open
your
web
browser,
and
type
http://192.168.0.1
into
the
address
bar.
This
will
take
you
to
the
KR2
Web
 Interface
and
the
Admin/Setup
Pages.
 
 7. Enter
the
KR2
password.
The
password
is
the
last
6
characters
  • Kyocera KR2 | Modem Setup - Page 2
    
 
 10. On
the
Welcome
screen,
click
Next.
 
 11. You
can
accept
the
default
password
(same
as
the
Administrator
Login)
or
change
your
password
here
and
 reenter
to
verify.

 12. Change
the
time
zone
to
Hawaii.

 13. Click
Next.
 2

  • Kyocera KR2 | Modem Setup - Page 3
    
security
and
compatibility.
The
 system
will
choose
the
higher
of
the
two
securities
automatically.
If
you
choose
NONE
there
may
be
a
problem
 getting
the
Hele
card
to
communicate
with
the
router
(EVDO
light
on
router
will
stay
yellow).
 16. Click
Next.
 
 17. For
Wireless
Security
Password
enter
  • Kyocera KR2 | Modem Setup - Page 4
    
 19. Your
setup
is
complete!
Double
check
your
SSID
and
pre‐shared
key.

 20. Save
the
settings.

 21. When
prompted
to
reboot
-
select
Reboot
Later.
 
 4

  • Kyocera KR2 | Modem Setup - Page 5
    Setting
up
for
your
Hele
USB
Modem
 1. Click
on
the
Basic
tab
on
the
top
and
then should
be
written
in
on
the
back
of
your
Hele
brochure.

 3. Type
in
the
Password
mobipcs.
Verify
the
password
by
typing
in
again.

 4. Click
on
Save
Settings
at
top
of
page.
 5. When
the
message
displays
telling
you
to
  • Kyocera KR2 | Modem Setup - Page 6
    updates,
in
the
Under
Automatic
Time
Configuration
area,
select
Enable
NTP
 Server.

 8. Click
on
the
pull
down
list
for
"Select
NTP
Server"
and
select
time.nist.gov.

 9. Click
on
Save
Settings.
 10. When
the
message
displays
telling
you
reboot
is
needed,
click
on
Reboot
Now.
 11. After
your
router
  • Kyocera KR2 | Modem Setup - Page 7
    For
FAQs,
firmware
updates,
and
additional
support
information,
 please
visit
the
Kyocera
website
at
www.kyocera‐wireless.com/support.
 
 If
you
forget
your
Wireless
Security
Password,
you
will
have
to
reset
the
modem
back
to
the
defaults.
See
the
 included
Quick
Start
Guide
for
instructions
on
this
  • Kyocera KR2 | Modem Setup - Page 8
    .
 3. Card
has
RF
signal
(green
light
on
card
should
be
on
and
flashing.
Follow
instructions
in
Kyocera
QuickStart
 Guide
for
checking
signal
strength.)
 4. The
correct
Username
and
password
of
the
card
has
been
entered
into
the
router
on
the
Basic>WAN
tab.
 Username
must
be

@mobipcs.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
1
Setting up the Kyocera KR2 Mobile Router with the Hele USB Modem
*Important* Install and activate your Hele USB modem directly in your computer before setting up the Kyocera router.
1.
Insure that the WLAN switch on the back of the router labeled ON/OFF is set to ON.
2.
Connect the supplied LAN cable from the yellow LAN port #1 on the back of the router to the LAN connector on
your computer.
3.
DO NOT plug the Hele card into the router yet.
4.
Plug the AC power supply into the back of the router and then into a wall outlet.
5.
Start your computer.
6.
Open your web browser, and type
into the address bar. This will take you to the KR2 Web
Interface and the Admin/Setup Pages.
7.
Enter the KR2 password. The password is the
last 6 characters of the KR2’s WLAN MAC ID
. This information is
located on the product label located on the bottom of the KR2.
8.
Click on Log In. The Setup Wizard screen appears.
9.
On the Setup Wizard screen, click on Launch Setup Wizard.