Kyocera TASKalfa 250ci Kyocera Command Center Operation Guide Rev 6.3 - Page 18

Basic > Security > Device Security > General - smb

Get Kyocera TASKalfa 250ci PDF manuals and user guides View all Kyocera TASKalfa 250ci manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

COMMAND CENTER Pages Authentication, see Advanced > Management > Authentication > General on page 3-47. Setting the Admin password is highly recommended to prevent unauthorized changes to the machine and networking configuration. With some models, the default Administrator password is factory-set as admin00. It is recommended to periodically change password. To change the password: 1 Enter the Old Password. 2 Enter the password you want to set in New Password. This can be up to 32 (30 with some models) character long. 3 Enter the same password in Confirm New Password. 4 Click Submit. Basic > Security > Device Security > General This page allows you to restrict access from the operation panel or USB host device. In addition, an explanation about each security setting is displayed. Lock Operation Panel Restricts access from the operation panel. With some models, this setting is irrelevant if the user has logged in as the Administrator. When it is set to Lock (Block), use of the System menu on this machine, registration in and editing of the Address Book and Box, use of the Stop key, and cancellation of jobs are forbidden. When it is set to Partial Lock, use of the System menu on this machine and registration in and editing of the Address Book and Box are forbidden. When it is set to Unlock, use of all keys is permitted. Filtering/Firewall, SNMPv1/v2, SNMPv3, SSL, IPSec, IEEE802.1x An explanation about each security setting is displayed. When you click a link in the sentence, the appropriate tab of the Advanced page opens. Basic > Security > Device Security > Interface Block This page allows you to restrict access from each interface. Network, USB Device, USB Host, Parallel I/F, Optional I/F Specifies whether or not to restrict access from each of the interfaces above. Access from the interfaces that are set to Block is restricted. Access from the network interface cannot be restricted. Access can be restricted on a per-protocol basis. Refer to the next section. Basic > Security > Device Security > Network Security This allows you to enable communication with the printing system on a per-protocol basis. SNMP v3, NetWare, AppleTalk, NetBEUI, Raw, IPP, IPP over SSL, HTTP, HTTPS, FTP (Transmission), FTP (Reception), SMB, SNMP, SMTP, POP3, LPD, LDAP, WSD Scan, WSD Print, ThinPrint, Enhanced WSD, Enhanced WSD over SSL 3-11 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
COMMAND CENTER Pages
Authentication, see
Advanced > Management > Authentication > General
on
page 3-47.
Setting the Admin password is highly recommended to prevent unauthorized
changes to the machine and networking configuration. With some models, the
default Administrator password is factory-set as admin00. It is recommended to
periodically change password.
To change the password:
1
Enter the Old Password.
2
Enter the password you want to set in
New Password
. This can be up to 32 (30
with some models) character long.
3
Enter the same password in
Confirm New Password
.
4
Click
Submit
.
Basic > Security > Device Security > General
This page allows you to restrict access from the operation panel or USB host
device. In addition, an explanation about each security setting is displayed.
Lock Operation Panel
Restricts access from the operation panel. With some models, this setting is
irrelevant if the user has logged in as the Administrator.
When it is set to
Lock
(Block), use of the
System menu
on this machine,
registration in and editing of the Address Book and Box, use of the Stop key,
and cancellation of jobs are forbidden. When it is set to
Partial Lock
, use of
the
System menu
on this machine and registration in and editing of the
Address Book and Box are forbidden. When it is set to
Unlock
, use of all
keys is permitted.
Filtering/Firewall, SNMPv1/v2, SNMPv3, SSL, IPSec, IEEE802.1x
An explanation about each security setting is displayed. When you click a
link in the sentence, the appropriate tab of the
Advanced
page opens.
Basic > Security > Device Security > Interface Block
This page allows you to restrict access from each interface.
Network, USB Device, USB Host, Parallel I/F, Optional I/F
Specifies whether or not to restrict access from each of the interfaces above.
Access from the interfaces that are set to
Block
is restricted.
Access from the network interface cannot be restricted. Access can be
restricted on a per-protocol basis. Refer to the next section.
Basic > Security > Device Security > Network Security
This allows you to enable communication with the printing system on a
per-protocol basis.
SNMP v3
,
NetWare
,
AppleTalk
,
NetBEUI
,
Raw
,
IPP
,
IPP over SSL
,
HTTP
,
HTTPS
,
FTP (Transmission)
,
FTP (Reception)
,
SMB
,
SNMP
,
SMTP
,
POP3
,
LPD
,
LDAP
,
WSD Scan
,
WSD Print
,
ThinPrint, Enhanced WSD, Enhanced
WSD over SSL
User Guide
3-11