Kyocera TASKalfa 250ci Kyocera Command Center Operation Guide Rev 6.3 - Page 45

Advanced > Protocols > TCP/IP > Logical Printers, IP Filters IPv6, IP Address IPv6, Prefix Length

Get Kyocera TASKalfa 250ci PDF manuals and user guides View all Kyocera TASKalfa 250ci manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

COMMAND CENTER Pages • LPD • FTP • IPP • ThinPrint • HTTP • Raw • SNMP • IPP over SSL • HTTPS IP Filters (IPv6) • IP Address (IPv6) Specifies the IP addresses to which access is granted. The number of addresses that can be specified varies depending on the model used. • Prefix Length Specifies the IPv6 prefix length. It can be a decimal value between 0 and 128. • Protocols Specifies the protocols through which access is granted. The following protocols can be selected. • LPD • FTP • IPP • ThinPrint • HTTP • Raw • SNMP • IPP over SSL • HTTPS Advanced > Protocols > TCP/IP > Logical Printers This page allows you to configure the Logical Printers. This machine can be used as a virtual printer for converting ASCII print data to PostScript data or for adding and/or replacing a character strings (commands) at the beginning or end of job data. Up to four logical printers can be set. Each logical printer can be used with either the FTP, LPR, IPP, NetBEUI, or Raw Port protocol. All printout to a non-existent port will be accomplished to Logical Printer1. TCP/IP Port Number Specifies the port number for the logical printer as well as the TCP raw port number (9100, etc.). Conversion is applied to data that is input to the specified raw port in accordance with the selected logical printer. This port is invalid if it is given a port number that is the same as that of an already specified port (For example, FTP or LPD). Bi-directional Printing On or Off Bi-directional Printing using the TCP/IP raw port. With this setting Off, all send data are discarded. In order to have the data that is received COMMAND CENTER 3-38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
COMMAND CENTER Pages
•
LPD
•
FTP
•
IPP
•
ThinPrint
•
HTTP
•
Raw
•
SNMP
•
IPP over SSL
•
HTTPS
IP Filters (IPv6)
•
IP Address (IPv6)
Specifies the IP addresses to which access is granted. The number of
addresses that can be specified varies depending on the model used.
•
Prefix Length
Specifies the IPv6 prefix length. It can be a decimal value between 0 and 128.
•
Protocols
Specifies the protocols through which access is granted. The following
protocols can be selected.
•
LPD
•
FTP
•
IPP
•
ThinPrint
•
HTTP
•
Raw
•
SNMP
•
IPP over SSL
•
HTTPS
Advanced > Protocols > TCP/IP > Logical Printers
This page allows you to configure the Logical Printers. This machine can be
used as a virtual printer for converting ASCII print data to PostScript data or for
adding and/or replacing a character strings (commands) at the beginning or end
of job data. Up to four logical printers can be set.
Each logical printer can be used with either the FTP, LPR, IPP, NetBEUI, or
Raw Port protocol. All printout to a non-existent port will be accomplished to
Logical Printer1.
TCP/IP Port Number
Specifies the port number for the logical printer as well as the TCP raw port
number (9100, etc.). Conversion is applied to data that is input to the
specified raw port in accordance with the selected logical printer. This port is
invalid if it is given a port number that is the same as that of an already
specified port (For example, FTP or LPD).
Bi-directional Printing
On
or
Off
Bi-directional Printing using the TCP/IP raw port. With this setting
Off
, all send data are discarded. In order to have the data that is received
COMMAND CENTER
3-38