Lenovo ThinkPad T430 (English) User Guide - Page 156

Errors without messages, Message, Solution, Attention, Problem, Power plan, Maximum Performance

Page 156 highlights

• Message: Fan error Solution: Cooling fan has failed. Shut down the computer immediately and have the computer serviced. • Message: Thermal sensing error Solution: The thermal sensor has problem. Shut down the computer immediately and have the computer serviced. • Message: This system does not support batteries that are not genuine Lenovo made or authorized. The system will continue to boot, but may not charge unauthorized batteries. Press the ESC key to continue. Attention: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use. Solution: Replace the battery with the correct Lenovo battery for this computer. If you still see the same error message, contact Lenovo service to have the computer serviced. • Message: The battery installed is not supported by this system and will not charge. Please replace the battery with the correct Lenovo battery for this system. Press the ESC key to continue. Solution: Replace the battery with the correct Lenovo battery for this computer. If you still see the same error message, contact Lenovo service to have the computer serviced. Errors without messages • Problem: My screen keeps blanking when I do not want it to. Solution: You can disable any system timers, such as the LCD turn-off timer or the blank timer by doing the following: 1. Start Power Manager. 2. Click the Power plan tab, and then select Maximum Performance from the predefined power plans. • Problem: When I turn on the computer, nothing is displayed on the screen and the computer does not beep while starting up. Note: If you are not sure whether you heard any beeps, turn off the computer by pressing and holding the power switch for four seconds or more. Turn it on and listen again. Solution: Make sure that: - The battery is installed correctly. - The ac power adapter is connected to the computer and the power cord is plugged into a working electrical outlet. - The computer is turned on. (Turn the power switch on again for confirmation.) If a power-on password is set: - Press any key to display the prompt for the power-on password. If the brightness level of the screen is low, increase it by pressing Home. - Type the correct password and press Enter. If these items are correctly set, and the screen remains blank, have the computer serviced. • Problem: When I turn on the computer, only a white cursor is displayed on a blank screen. Solution: If you have modified a partition on your hard disk drive by using partition software, information about that partition, or the master boot record might have been destroyed. 1. Turn off the computer, and then turn it on again. 2. If you still see only the cursor on the screen, do the following: - If you have used the partition software, examine the partition on the hard disk drive by using the software, and recover the partition if required. 138 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190

Message
: Fan error
Solution
: Cooling fan has failed. Shut down the computer immediately and have the computer serviced.
Message
: Thermal sensing error
Solution
: The thermal sensor has problem. Shut down the computer immediately and have the computer
serviced.
Message
: This system does not support batteries that are not genuine Lenovo made or authorized. The
system will continue to boot, but may not charge unauthorized batteries. Press the ESC key to continue.
Attention
: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and
provides no warranties for failures or damage arising out of their use.
Solution
: Replace the battery with the correct Lenovo battery for this computer. If you still see the same
error message, contact Lenovo service to have the computer serviced.
Message
: The battery installed is not supported by this system and will not charge. Please replace the
battery with the correct Lenovo battery for this system. Press the ESC key to continue.
Solution
: Replace the battery with the correct Lenovo battery for this computer. If you still see the same
error message, contact Lenovo service to have the computer serviced.
Errors without messages
Problem
: My screen keeps blanking when I do not want it to.
Solution
: You can disable any system timers, such as the LCD turn-off timer or the blank timer by
doing the following:
1. Start Power Manager.
2. Click the
Power plan
tab, and then select
Maximum Performance
from the predefined power plans.
Problem
: When I turn on the computer, nothing is displayed on the screen and the computer does not
beep while starting up.
Note:
If you are not sure whether you heard any beeps, turn off the computer by pressing and holding the
power switch for four seconds or more. Turn it on and listen again.
Solution
: Make sure that:
The battery is installed correctly.
The ac power adapter is connected to the computer and the power cord is plugged into a working
electrical outlet.
The computer is turned on. (Turn the power switch on again for confirmation.)
If a power-on password is set:
Press any key to display the prompt for the power-on password. If the brightness level of the screen
is low, increase it by pressing Home.
Type the correct password and press Enter.
If these items are correctly set, and the screen remains blank, have the computer serviced.
Problem
: When I turn on the computer, only a white cursor is displayed on a blank screen.
Solution
: If you have modified a partition on your hard disk drive by using partition software, information
about that partition, or the master boot record might have been destroyed.
1. Turn off the computer, and then turn it on again.
2. If you still see only the cursor on the screen, do the following:
If you have used the partition software, examine the partition on the hard disk drive by using the
software, and recover the partition if required.
138
User Guide