Lexmark 854e Clearing Jams Guide

Lexmark 854e - X MFP B/W Laser Manual

Get Lexmark 854e - X MFP B/W Laser PDF manuals and user guides
UPC - 734646257688
View all Lexmark 854e manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark 854e manual content summary:

  • Lexmark 854e | Clearing Jams Guide - Page 1
    Lexmark™ X85x Clearing Jams Guide have cut or trimmed yourself. • Do not mix print media sizes, weights, or types in the same print media source. • Make sure the the release latch and lowering the door. CAUTION: The inside of the MFP might be hot. 2 Pull the print media up and toward you.
  • Lexmark 854e | Clearing Jams Guide - Page 2
    . 230 Jam 1 Open Door D by the duplex rear door. 5 Open Door E by pushing the release latch and lowering the door. CAUTION: The inside of the MFP might be hot. 2 Open Door E by pushing the release latch and lowering the door. 2 Remove the jammed media. 6 Pull the print media up. 3 Pull the
  • Lexmark 854e | Clearing Jams Guide - Page 3
    paper from the tray. 4 Insert the tray into the MFP. 5 Touch Continue. 250 Jam 1 Remove the paper from the multipurpose feeder. 2 Flex, fan, and restack the media, and place it into the multipurpose feeder. 3 Load the print media. 4 Slide the side guide toward the inside of the tray until it lightly
  • Lexmark 854e | Clearing Jams Guide - Page 4
    5) 1 If necessary, close the multipurpose feeder. 2 Slide the high capacity feeder away from the MFP. 5 Close the jam access cover and top door. 2 Open Door B. 6 Slide the feeder firmly against the MFP. 3 Remove the jammed media. 3 Raise the top door, and lift the jam access cover. 4 Remove
  • Lexmark 854e | Clearing Jams Guide - Page 5
    , slide the feeder away from the MFP. 5 Slide the feeder firmly against the MFP. Clearing Area G 1 Open the finisher door. 2 Open Door C. 3 Remove the jammed media. 4 Close Door C. 6 Touch Continue. 280-288 Jams These are finisher jams. Follow the appropriate instructions to clear a jam in the
  • Lexmark 854e | Clearing Jams Guide - Page 6
    Clearing staple jams 289 Jam 1 Check that the machine stops operations, and open Door G (front door) of the finisher. 2 Hold the lever on the staple cartridge holder, and move the holder to the right (towards you). Discard the entire sheet. Clearing ADF Jams 290, 291, 292, and 294 Jams 1 Remove
  • Lexmark 854e | Clearing Jams Guide - Page 7
    left to remove any jammed pages. Paper advance wheel 6 Close the ADF cover. 8 Close the document cover. 9 Touch Continue. 293 Jam A 293 jam indicates the MFP was sent a scan job, but found no original document in the ADF. To resolve a 293 Jam: • Touch Continue if no scan job is active when
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
Lexmark™ X85x
Clearing Jams
Guide
Avoiding jams
The following hints can help you avoid jams:
•
Use only recommended print media.
•
Do not overload the print media sources. Make
sure the stack height does not exceed the
maximum height indicated by the stack line on
the labels in the sources.
•
Do not load wrinkled, creased, damp, or curled
print media.
•
Flex, fan, and straighten print media before you
load it. If jams do occur with print media, try
feeding one sheet at a time through the
multipurpose feeder.
•
Do not use print media that you have cut or
trimmed yourself.
•
Do not mix print media sizes, weights, or types
in the same print media source.
•
Make sure the recommended print side is
loaded in the source according to your simplex
or duplex needs.
•
Keep print media stored in an acceptable
environment.
•
Do not remove trays during a print job.
•
Push all trays in firmly after loading them.
•
Make sure the guides in the trays are properly
positioned for the size of print media you have
loaded. Make sure the guides are not placed
too tightly against the stack of print media.
Clearing Jams
Understanding jam numbers
200–202 Jams
1
Open Door A by pushing the release latch and
lowering the door.
CAUTION:
The inside of the MFP might be hot.
2
Pull the print media up and toward you.
Warning:
If the print media does not move
immediately when you pull, stop
pulling. Push down and pull the
green lever to make it easier to
remove the media. Make sure all
paper fragments are removed.
3
Close Door A.
4
Touch
Continue
.
Jam
What to do
200–202 Jams
Open Door A, and remove the
jam.
203 Jam
Open the Door A and Door E,
and remove the jam.
230 Jam
Open Door D, and remove the
jam. Open the Door A and Door
E, and remove the jam.
231 Jam
Open Door D, and remove the
jam. Open the Door A and Door
E, and remove the jam.
24x Jams
Open each tray, and remove any
jammed media.
250 Jam
Remove all media from the
multipurpose feeder, flex and
stack the media, reload the
multipurpose feeder, and adjust
the guide.
280-288 Jams
As directed by the message,
check area F, G, or H, then
remove the jam.
289 Jam
Remove the staple cartridge,
then remove any jammed
staples.
290, 291, 292, and
294 Jams
Open the ADF cover and the
scanner cover, and remove any
jammed media.
293 Jam
Select the location of your
original document, finish your job
without further scanning, restart
scanning, or cancel the job and
clear the message.