Lexmark C792 IPDS Printer and Host Setup Guide
Lexmark C792 Manual
 |
View all Lexmark C792 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark C792 manual content summary:
- Lexmark C792 | IPDS Printer and Host Setup Guide - Page 1
Lexmark Card for IPDS and Card for IPDS and SCS/TNe IPDS Printer and Host Setup Guide - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 2
, are the user's responsibility. Trademarks AFP, AS/400, IBM, iSeries, MVS, OS/2, OS/390, OS/400, Print Services Facility, PSF, System/390, zSeries, and z/OS are trademarks of International Business Machines Corporation in the United States, other countries, or both. Intelligent Printer Data Stream - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 3
and Host Setup Guide - Table of Contents TABLE OF CONTENTS Notices ...2 Table of Contents...3 Equipment Requirements and Specifications 4 Customer Support...5 1. iSeries and AS/400 LAN Printing Using the Printer Standard Network Port or MarkNet Internal Print Server ...6 2. PSF/MVS LAN Printing - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 4
REQUIREMENTS AND SPECIFICATIONS This guide provides information to help you configure the host and printer to print IPDS jobs. The information in this guide applies to the following printers and Multifunction Products (MFPs). • Lexmark C734, C736 • Lexmark C792 • Lexmark C925 • Lexmark E460dn - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 5
IPDS Printer and Host Setup Guide Equipment Requirements And Specifications Customer Support If you cannot find answers in this guide about using the IPDS emulation, or require firmware updates, please contact your point of purchase, your local Lexmark office, or check the Lexmark support web site - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 6
or MarkNet internal LAN print server. Refer to the IPDS User's Guide for detailed instructions on using the control panel to select and change option settings. Steps The following steps must be completed to begin printing IPDS jobs. 1 Choose a Printer Port for Use in the Device Description 2 Create - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 7
substitution messages FNTSUBMSG Capture host fonts at printer......... FNTCAPTURE Font resolution for formatting........ FNTRSL Font mapping table FNTTBL Library Cut sheet emulation mode CSEMODE Use DBCS simulation fonts MAPIGCFNT Replace REPLACE Authority AUT Press PF9 to show the - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 8
library list: ........ *NO *DFT Note 1: IPDS pass through may be set to *YES. This may increase job performance. Selecting *YES may change the fonts downloaded from the host and change paper jam recovery action between the host and printer. Note 2: SEC15 is recommended. Refer to "Printer and - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 9
*NONE Library User defined driver program........... USRDRVPGM *NONE Library Secure connection SECURECNN *NO Validation list VLDL *NONE Library Publishing information PUBLISHINF Support duplex *UNKNOWN Support color *UNKNOWN Pages per minute black *UNKNOWN Pages - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 10
a Standard Network port or a MarkNet internal LAN print server, several settings must be verified. You can verify these settings from the printer control panel as shown below. 1 From a Ready state press the MENU button (printers). Touch or on touch screens. 2 Use the navigation buttons or icon - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 11
for Choosing the IPDS Emulation Setting The IPDS Emulation, the BAR CODE and Host Resolution options are found in the printer control panel under MENU/Menus > Option Card Menu > IPDS MENU > EMULATION. 1 "Resident" is the default setting. If you are replacing a printer that used a Native Emulation - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 12
is controlled by the Release Timer on the host or by the IPDS Timeout on the printer. 6 You may want to refer to the IPDS Emulation User's Guide to determine if other IPDS MENU settings need to be changed. Step 7 Troubleshooting If the IPDS job does not print, try the following. 1 If Busy or IPDS is - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 13
MENU/Menus, select Option Card Menu > IPDS MENU > EMULATION > BARCODE > Bar Code Size. 7 Refer to Chapter 5. Printer Messages and Problems on page 31 for additional problem solutions. 8 Once the job prints, refer to the IPDS Emulation User's Guide for information on changing other IPDS MENU settings - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 14
will lead you through the steps for setting up the MVS mainframe and printer to print IPDS jobs over a LAN. The printer must be configured with a Standard Network port or MarkNet internal LAN print server. Refer to the IPDS User's Guide for detailed instructions on using the control panel to select - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 15
Jobs 2 Define the printer to JES 3 Add the printer to the PSF STARTUP PROC 4 Configure the Printer's Print Server TCP/IP Settings 5 Select the IPDS Emulation, Bar Code Size, Host Resolution, and Fax Interrupt Settings 6 Verify IPDS Printing 7 Troubleshooting Step 1 Choose a Printer Port for Printing - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 16
TRAILER */ // DSHDR=*.DSHDR, /* DATA SET HEADER */ // FORMDEF=A10110, /* FORMDEF */ // PIMSG=(YES,16), /* MESSAGES */ // DATACK=UNBLOCK, /* REPORT ALL DATA CHECKS */ // TRACE=NO, /* INTERNAL TRACE */ // MGMTMODE=OUTAVAIL, /* PRINTER MANAGEMENT MODE */ // CONNINTV=0, /* NO TIMEOUT - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 17
// DD DSN=INST.FONTLIB,DISP=SHR/* USER FONTS */ // * // PSEG02 DD DSN SET HEADER */ // FORMDEF=A10110, /* FORMDEF */ // PIMSG=(YES,16), /* MESSAGES */ // DATACK=UNBLOCK, /* PRINT ALL DATA CHECKS */ // TRACE=NO, /* INTERNAL TRACE */ // MGMTMODE=OUTAVAIL, /* PRINTER MANAGEMENT MODE - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 18
on printers, press the Select button ; on touch screens touch Network/Ports. 4 Now you will see a list of menus. Select the Standard Network menu. (Off, if you set the IP address another way.) Enable AutoIP Yes or No (Default is Yes. This is the recommended setting.) WINS Server Address 157 - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 19
for Choosing the IPDS Emulation Setting The IPDS Emulation, the BAR CODE and Host Resolution options are found in the printer control panel under MENU/Menus > Option Card Menu > IPDS MENU > EMULATION. 1 "Resident" is the default setting. If you are replacing a printer that used a Native Emulation - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 20
controlled by the DISCINTV value on the host or by the IPDS Timeout on the printer. 4 You may want to refer to the IPDS Emulation User's Guide to determine if other IPDS MENU settings need to be changed. Step 7 Troubleshooting If the IPDS job does not print, try the following. 1 If Busy or IPDS is - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 21
IPDS Printer and Host Setup Guide PSF/MVS LAN Printing Using the Standard Network Port or Internal Print Server 9 Once the job prints, refer to the IPDS Emulation User's Guide for information on changing other IPDS MENU settings. 21 - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 22
below will lead you through the steps for setting up PSF/2 and the printer to print IPDS jobs over a LAN. The printer must be configured with a Standard Network port or a MarkNet internal LAN print server. Refer to the IPDS User's Guide for detailed instructions on using the control panel to select - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 23
Printer and Host Setup Guide PSF/2 LAN Printing Using an Internal LAN Print Server b) On the PSF/2 Control Panel select Profile and then New. The PSF/2 New Device menu as Attachment Type and select Settings. The TCP/IP Settings menu appears. Enter the IP address of the printer. The IP address should - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 24
Sharing With the Job Interval Shutdown Timer To enable the printer to start other print jobs from another protocol, interface or server, the PSF/2 tuning option Job Interval Shutdown Timer is used. Use the following steps to set the Job Interval Shutdown Timer option: a) Start the PSF/2 control - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 25
IPDS Printer and Host Setup Guide PSF/2 LAN Printing Using an Internal LAN Print Server b) On the PSF/2 Control Panel select Profile and then Change. c) Now select Tuning Options. The Job - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 26
a Standard Network port or a MarkNet internal LAN print server, several settings must be verified. You can verify these settings from the printer control panel as shown below. 1 From a Ready state press the MENU button (printers). Touch or on touch screens. 2 Use the navigation buttons or icon - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 27
for Choosing the IPDS Emulation Setting The IPDS Emulation, the BAR CODE and Host Resolution options are found in the printer control panel under MENU/Menus > Option Card Menu > IPDS MENU > EMULATION. 1 "Resident" is the default setting. If you are replacing a printer that used a Native Emulation - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 28
MENU/Menus, select Option Card Menu > IPDS MENU > EMULATION > BARCODE > Bar Code Size. 7 Refer to Chapter 5. Printer Messages and Problems on page 31 for additional problem solutions. 8 Once the job prints, refer to the IPDS Emulation User's Guide for information on changing other IPDS MENU settings - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 29
jobs. Selection of some values will cause communication problems between the printer and the host. Use the tables below to verify the timeout settings in the printer and on the host. AS/400 or iSeries host and Printer IPDS Timeout Values Printer IPDS Timeout Host Controlled Host Controlled Host - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 30
IPDS Printer and Host Setup Guide Printer and Host Timeout Values MVS host and Printer IPDS Timeout Values Printer IPDS Timeout Host Controlled Host Controlled 15 sec to 10 Min 15 sec to 10 Min STARTUP PROC STARTUP PROC Note Disconnect Interval (DISCINTV) Valid Port Number (PORTNO) Specific - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 31
or for keywords for a problem. Message (bold) or Problem Problem Number Printer remains in Ready and message on Host 1 1510 Incorrect DLE Installation, install in the other 2 slot 34 Incorrect Media 10 1565 EMUL ERROR 9 900.40 Firmware error 15 Bad Memory System 8 Busy 3 Disk Full - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 32
system card. Some models require the optional firmware card to be installed in a specific connector. Problem 3: Fatal error in print queue; incorrect Busy / Timeout The print queue stops with a fatal error which requires operator intervention or the printer displays Busy or IPDS even when no IPDS - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 33
to the host. Solution to Problem 4 You need to do one or more of the following: A. Postscript or PCL resources may be saved in the printer memory. The memory cannot be used by IPDS. Set Resource Save to "Off" in the printer menu to allow permanent downloaded resources from PostScript and PCL jobs - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 34
Guide Printer Messages and Problems requirements on each supported printer, refer to the appendix on memory requirements and recommendations in the IPDS Emulation User's Guide. D. The host may be downloading more IPDS resources than can be held in the printer's memory. Add more memory to the printer - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 35
EMUL ERROR LOAD EMUL OPTION appears on the display after updating the printer code. Solution to Problem 9 The IPDS emulation version contained in the Card will not function with the printer code. Download the correct IPDS emulation version. See the section on support (page 5) for firmware update - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 36
jobs is 5001. Problem 15: Message "900.40 Firmware error" displays when I power on the printer The printer control panel displays "900.40 Firmware error.. ..256MB required" when I power on the printer with the IPDS card installed. Solution to Problem 15 A minimum of 256 MB of user memory (DRAM) is - Lexmark C792 | IPDS Printer and Host Setup Guide - Page 37
IPDS Printer and Host Setup Guide Printer Messages and Problems 37
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
 |
 |
Lexmark
Card for IPDS
and
Card for IPDS and SCS/TNe
IPDS Printer and Host Setup Guide