Lexmark C792 Quick Reference
Lexmark C792 Manual
 |
View all Lexmark C792 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark C792 manual content summary:
- Lexmark C792 | Quick Reference - Page 1
Menu > Paper Size/Type > select a tray > select the paper size or type > The factory default Paper Type setting is Plain Paper. Configuring Universal paper settings The Universal Paper Size is a user-defined setting that lets you print on paper sizes that are not preset in the printer menus. Set - Lexmark C792 | Quick Reference - Page 2
of the tray for duplex printing. • Make sure the paper is below the maximum fill line located on the edge of the paper tray. Overloading the tray can cause paper jams and possible printer damage. 7 From the printer control panel, verify the Paper Size and Paper Type for the tray based on the paper - Lexmark C792 | Quick Reference - Page 3
cause paper jams and possible printer damage. manual printing, or as an additional tray. The multipurpose feeder can hold approximately: • 100 sheets of 75-g/m2 (20-lb) paper • 10 envelopes • 75 transparencies The multipurpose feeder accepts paper or specialty media within the following dimensions - Lexmark C792 | Quick Reference - Page 4
the paper guides in each tray except Tray 1 and the multipurpose feeder. The Paper Size setting for the multipurpose feeder must be set manually from the Paper Size menu. The Paper Type setting must be set for all trays from the Paper Type menu. The Paper Type menu and the Paper Size menu are both - Lexmark C792 | Quick Reference - Page 5
and resume printing. The printer prints a new copy of the page that jammed if Jam Recovery is set to On or Auto; however, the Auto setting does not guarantee the page will print. Note: Jam recovery is set to Auto by default. The printer reprints jammed pages unless the memory required to hold the - Lexmark C792 | Quick Reference - Page 6
Damage: Do not touch the center of the fuser unit. Doing so will damage the fuser. Note: Make sure all paper fragments are removed. 3 Close the side door of the printer. 4 From the printer control panel, touch Continue, jam cleared. 202-203 paper jams If paper is visible in the standard exit bin - Lexmark C792 | Quick Reference - Page 7
unit. Doing so will damage the fuser. Note: Make sure all paper fragments are removed. 4 Close the side door. Paper jam under the fuser 1 Open the side door of the printer. 3 Grasp the jammed paper, and then gently pull it out. Note: Make sure all paper fragments are removed. 4 Close the duplex - Lexmark C792 | Quick Reference - Page 8
fragments are removed. 3 Reload paper into the multipurpose feeder, and then adjust the paper guides. 4 From the printer control panel, touch Continue, jam cleared. 400-403 and 460-461 paper jams 1 Open the paper transport unit door. 1 2 Open the finisher or mailbox access door. 2 Firmly grasp the - Lexmark C792 | Quick Reference - Page 9
and then remove any jammed or loose staples. 6 Push the staple cartridge holder firmly back into the stapler unit until the staple cartridge holder clicks into place. 2 Lower the latch of the staple cartridge holder, and then pull the staple cartridge holder out of the printer. 4 Close the staple - Lexmark C792 | Quick Reference - Page 10
setting 1 paper jams avoiding 5 paper jams, clearing 200 paper jam 6 201 paper jam 6 202-203 paper jams 6 230 paper jam 7 231-239 paper jams 7 24x paper jam 7 250 paper jam 8 400-403 paper jams 8 431-454 paper jams 8 456-458 paper jams 8 460-461 paper jams 8 paper size setting 1 paper type setting
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
 |
 |
Quick Reference
Loading paper and
specialty media
This section explains how to load the 550-sheet tray, an optional
2,000-sheet tray, a multipurpose feeder, and an optional 550-sheet
specialty media drawer. It also includes information about paper
orientation, setting the Paper Size and Paper Type, and linking and
unlinking trays.
Setting the paper size and type
The Paper Size setting is automatically sensed according to the
position of the paper guides in each tray except the multipurpose
feeder. The Paper Size setting for the multipurpose feeder must be
set manually from the Paper Size menu. The Paper Type setting must
be set manually for all trays that do not contain plain paper.
From the home screen navigate to:
>
Paper Menu
>
Paper Size/Type
> select a tray > select the
paper size or type >
The factory default Paper Type setting is Plain Paper.
Configuring Universal paper
settings
The Universal Paper Size is a user-defined setting that lets you print
on paper sizes that are not preset in the printer menus. Set the Paper
Size for the specified tray to Universal when the size you want is not
available from the Paper Size menu. Then, specify all of the following
Universal size settings for your paper:
•
Units of Measure
•
Portrait Width
•
Portrait Height
Notes:
•
The largest supported Universal size is 216 x 1219 mm
(8.5 x 48 in.).
•
The smallest supported Universal size is 76 x 127 mm (3 x 5 in.)
and loaded in the multipurpose feeder only.
From the home screen, navigate to:
>
Paper Menu
>
Universal Setup
>
Units of Measure
> select
unit of measure >
Portrait Width
or
Portrait Height
> select width
or height >
Loading the standard or optional
550-sheet tray
The printer has one standard 550-sheet tray (Tray 1), and may have
one or more optional 550-sheet trays. All 550-sheet trays support the
same paper sizes and types.
1
Pull the tray out.
Notice the size indicators on the bottom of the tray. Use these
indicators to help position the length and width guides.
LTR
LGL
A4
A4
LTR
LGL
2
Squeeze and then slide the width guide to the correct position for
the paper size you are loading.
3
Squeeze and then slide the length guide to the correct position
for the paper size you are loading.
Note:
The length guide has a locking device. To unlock, slide the
button on top of the length guide down. To lock, slide the button
up when a length has been selected.
1