Home » Lexmark Manuals » Laser Printers » Lexmark C950 » Manual Viewer

Lexmark C950 Service Manual - Page 413

HCF media transport roll assembly operation, HCF media feed unit assembly sensor/motor functions

Add to My Manuals
Save this manual to your list of manuals

Page 413 highlights

5058-030 HCF media transport roll assembly operation Upon receiving the feed start signal from the controller the HCF activates the HCF transport motor at a high speed after a preset time has passed. This rotating power of the HCF transport motor is transmitted to the HCF media transport roll assembly, and the media from the HCF media feed unit assembly is transferred to the printer. When the sensor (tray 5 feed-out) is turned on by the media fed with the HCF media transport roll assembly, the HCF transport motor speed decreases after a preset time has passed. When the sensor (registration) in the printer is turned on by the media fed from the HCF, the HCF transport motor turns off. When the next feed start signal is received, before the HCF transport motor is turned off, the transport motor continues to rotate. Thus, media is transferred from the HCF media transport roll assembly to the laser printer. HCF transport motor Previous Next Go Back Media Sensor (tray 5 feed-out) HCF media transport roll assembly HCF media feed unit assembly sensor/motor functions Functions of the sensors and motors of the media feed unit assembly are outlined below. • HCF media feed lift motor-is a stepping motor that rotates (forward) the pick roll and feed roll to send media from the tray to the HCF media transport roll assembly. The motor also lifts the tray by reverse rotation. • HCF pick solenoid-Raises or lowers the pick roll. The HCF pick solenoid stays activated from the beginning of media feed until the sensor (pre-feed) turns on. The HCF pick solenoid is activated when the tray is inserted and when the power is turned on to check the presence of media in the tray. • Sensor (pre-feed)-Detects whether media has been fed from the tray, and controls the HCF feed lift motor speed. The sensor also becomes a trigger to deactivate the HCF pick solenoid. The sensor turns on upon detecting media, and determines that media is present. • HCF transport motor-is a stepping motor that rotates the HCF media transport roll assembly to feed media to the printer. • Sensor (tray 5 feed-out)-Detects whether media has been fed from the tray, becomes a trigger to stop the HCF feed lift motor, and controls the HCF transport motor speed. Diagnostic aids 3-125

Section	Page
Table of contents	4
Notices and safety information	23
Printhead LED notice	23
printhead LED-Hinweis	23
Avis relatif à l’utilisation de printhead LED	23
Avvertenze sui prodotti printhead LED	23
Avisos sobre el láser	23
Aviso sobre o printhead LED	24
printhead LEDinformatie	24
printhead LEDmeddelelse	24
printhead LEDilmoitus	24
printhead LED-notis	24
printhead LED-melding	24
Aviso de láser	25
Consignes de sécurité	27
Norme di sicurezza	27
Sicherheitshinweise	28
Pautas de Seguridad	28
Informações de Segurança	28
Informació de Seguretat	29
Preface	30
Navigation buttons	30
1. General information	33
Model	33
Options and features	33
Printer specifications	34
Electronics	34
SFP	34
Connectivity (network support)	35
Operating modes	35
Data streams	36
Dimensions	36
Clearances	36
Environment specifications	37
Media handling	38
Input and output sources	38
Media input size specifications	38
Media input type specifications	39
Media guidelines	43
Tools required for service	46
Acronyms	47
2. Diagnostic information	49
Start	49
POR (Power-On Reset) sequence	50
Error codes and messages	51
User status and attendance messages	51
Paper jam error codes	59
1xx service error codes	60
2xx service error codes	68
3xx service errors	72
4xx service error codes	76
8xx service error codes	79
9xx service error codes	79
Service checks	82
900.xx System software error	82
111.01 LED printhead (K) failure	85
111.02-111.04 LED printhead (K) signal failure	85
112.01 LED printhead (C) failure	86
112.02-112.04 LED printhead (C) signal failure	86
113.01 LED printhead (M) failure	86
113.02-113.04 LED printhead signal failure (M)	87
114.01 LED printhead failure (Y)	87
114.02-114.04 LED printhead (Y) signal failure	88
115.01 Multiple LED printhead power supply failure	88
115.02 Single LED printhead power failure	89
115.03 Multiple LED printhead download failure	89
115.04 Single LED printhead download failure	90
115.05 Multiple LED printhead mismatch failure	90
115.06 Single LED printhead mismatch failure	91
115.07 Multiple LED printhead read failure	91
115.08 Single LED printhead read failure	91
115.09 Multiple LED printhead write failure	92
115.10 Single LED printhead write failure	92
115.11 Multiple LED printhead communication failure	93
115.12 Single LED printhead communication failure	94
115.13 Multiple LED printhead clock failure	94
115.14 Single LED printhead clock failure	95
115.15 Tray module logic failure	95
120.01 Fuser motor failure	96
120.02 Fuser pressure roll retract motor failure	97
121.01 Encoder pulse failure	97
121.02 Encoder pulse failure	98
121.03 Heat belt (center) disconnection error	98
121.04 Heat belt (center) overheat error	98
121.05 Heat belt (rear) disconnection error	99
121.06 Heat belt (rear) overheat error	99
121.07 Heat belt (center) temperature increase failure	100
121.08 Heat belt (rear) temperature increase failure	100
121.09 Fuser temperature lag error	100
121.10 Heat belt rotation failure	101
121.11 Fuser temperature recovery failure	101
121.12 Incorrect fuser	101
121.13 Fuser thermostat failure	102
126.01 Fuser driver interface failure	102
126.02 Fuser driver to upper engine PCBA interface failure	102
126.03 Fuser driver communication failure	103
126.04 Fuser driver freeze failure	103
126.05 Fuser driver high voltage error	104
126.06 Fuser driver low voltage error	104
126.07 Fuser driver surge failure	104
126.08 IGBT high temperature error	104
126.09 IGBT temperature sensor failure	105
126.12 Input low current error	105
132.01 ATC sensor (K) failure	106
132.02 ATC sensor (Y) failure	107
132.03 ATC sensor (M) failure	109
132.04 ATC sensor (C) failure	110
137.01 Upper printer engine PCBA communication error	111
140.01 Registration drive motor failure	112
141.01 Drum drive motor (K) failure	112
141.02 Drum drive motor (Y/M/C) failure	113
151.01 Transfer belt motor failure	114
151.02 First transfer contact/retract failure	114
151.03 Second transfer contact/retract failure	115
154.01 Developer (Y/M/C) motor failure	116
155.01 Toner dispense motor (K) failure	117
156.01 Toner dispense motor (C) failure	118
157.01 Toner dispense motor (M) failure	118
158.01 Toner dispense motor (Y) failure	119
171.02 Fuser cooling fan failure	120
172.01 Front upper cooling fan failure	121
173.01 LVPS sub cooling fan failure	121
174.01 Charge roll HVPS cooling fan failure	121
175.01 Front right cooling fan failure	122
175.03 PC/developer drive motor cooling fan failure	122
175.04 Front left cooling fan failure	122
175.05 Suction fan failure	123
175.06 Center exhaust fan failure	123
175.07 Fuser driver PCBA cooling fan failure	123
175.08 Upper exhaust cooling fan failure	124
191.01 Lower engine PCBA detect failure	124
191.02–191.05 Upper engine PCBA fuse blown	124
191.06 Lower engine PCBA fuse 2 blown	125
191.07 Lower engine PCBA fuse 3 blown	125
191.08 Lower engine PCBA fuse 4 blown	126
191.09 Upper engine PCBA fuse 5 blown	126
191.10 Lower engine PCBA fuse 6 blown	126
191.11 Lower engine PCBA fuse 7 blown	127
191.12 Lower engine PCBA fuse 8 blown	127
191.13 Lower engine PCBA fuse 9 blown	128
191.14 Lower engine PCBA fuse 10 blown	128
191.15 Lower engine PCBA fuse 11 blown	128
191.16 Lower engine PCBA fuse 12 blown	129
191.17 Lower engine PCBA fuse 13 blown	129
191.18 Upper engine PCBA data failure	129
191.19 Upper engine PCBA access failure	130
191.20 Upper engine PCBA buffer failure	130
191.23 Lower engine PCBA fuse 14 blown	130
191.24 Lower engine PCBA fuse 15 blown	131
191.25 Lower engine PCBA fuse 16 blown	131
200.01 Sensor (registration) static jam	131
200.03 Sensor (registration) late jam (feeding from the tray)	132
200.03 Sensor (registration) late jam (feeding from the MPF)	134
200.05/200.55 Sensor (registration) lag jam	135
200.53 Sensor (registration) late jam (80K interval exceeded for feed rollers)	137
200.55 Sensor (registration) lag jam	140
201.01 Sensor (media on belt) static jam	140
201.03 Sensor (media on belt) late jam	141
202.01 Sensor (fuser exit) static jam	143
202.03 Exit Sensor 1 Late Jam	144
202.04/202.05 Sensor (fuser exit) lag jam	147
202.05 Sensor (fuser exit) lag jam	148
203.01 Sensor (upper redrive) static jam	149
203.03 Sensor (upper redrive) late jam	149
203.05 Sensor (upper redrive) lag jam	151
230.01 Sensor (duplex wait) static jam	153
231.03 Sensor (duplex wait) late jam	153
242.01 Sensor (tray 2 feed out) static jam	157
242.03/242.06 Sensor (tray 2 feed out) late jam	158
242.06 Sensor (tray 2 feed out) late jam	159
242.56 Sensor (tray 2 feed out) late jam (80K interval exceeded for feed rolls)	159
243.01 Sensor (tray 3 feed out) static jam	160
243.03/243.06 Sensor (tray 3 feed out) late jam	161
243.06 Sensor (tray 3 feed out) late jam	163
243.56 Sensor (tray 3 feed out) late jam (80K interval exceeded for feed rolls)	163
244.01 Sensor (tray 4 feed out) static jam	164
244.06 Sensor (tray 4 feed out) late jam	165
244.56 Sensor (tray 4 feed out) late jam (80K interval exceeded for feed rolls)	167
245.01 Sensor (tray 5 feed out) static jam	169
245.03 Sensor (tray 5 feed out) late jam	170
245.06 Sensor (tray 5 feed out) lag jam	171
245.56 Sensor (tray 5 feed out) late jam (80K interval exceeded for feed rolls)	172
245.56 Sensor (HCF feed out) late jam	174
250.05 Sensor (MPF feed out) lag jam	175
250.06 Sensor (MPF feed out) late jam	179
250.56 Sensor (MPF feed out) late jam (80K interval exceeded for feed rolls)	180
381.01 Sensor (front tamper HP) late jam	181
381.02 Sensor (front tamper HP) lag jam	182
381.03 Sensor (rear tamper HP) late jam	184
381.04 Sensor (rear tamper HP) lag jam	185
381.05 Sensor (stapler carriage HP) late jam	186
381.07 Stapler unit failure	188
381.08 Sensor (media eject clamp HP late jam	188
381.09 Sensor (media eject clamp HP) lag jam	189
381.10 Sensor (media eject shaft HP) late jam	190
381.11 Sensor (media eject shaft HP) lag jam	192
381.12 Stacker bin failure	193
381.13 Sensor (stacker bin upper limit) error	195
381.14 Sensor (stacker bin no media) error	197
381.15 Sensor (punch side reg 1/2) lag jam	199
381.16 Sensor (punch cam HP) late jam	201
381.17 Sensor (punch cam HP) lag jam	202
381.18 Sensor (punch carriage shift HP) late jam	203
381.19 Sensor (punch carriage shift HP) lag jam	204
381.26 Sensor (decurler cam HP) late jam	205
381.27 Sensor (decurler cam HP) lag jam	206
381.30 Sensor (booklet front tamper HP) late jam	207
381.31 Sensor (booklet front tamper HP) lag jam	209
381.32 Sensor (booklet end guide HP) lag jam	210
381.33 Sensor (booklet rear tamper HP) late jam	212
381.34 Sensor (booklet rear tamper HP) lag jam	213
381.35 Sensor (booklet knife folding) failure	215
381.36 Booklet unit fail	216
381.37 Sensor (booklet knife HP) late jam	217
381.38 Sensor (booklet knife HP) lag jam	219
381.39 Booklet Staple Fail	221
381.40 Sensor (booklet compiler media present) error	222
381.41 Communication error with booklet controller card assembly	223
401.01 Sensor (finisher media entrance) static jam	223
401.03 Sensor (bridge media entrance) late jam	224
401.05 Sensor (bridge media entrance) lag jam	225
402.01 Sensor (bridge media exit) static jam	226
402.03 Sensor (bridge media exit) late jam	228
481.01 Sensor (finisher media entrance) static jam	229
481.03 Sensor (finisher media entrance) late jam	230
482.01 Sensor (diverter gate) static jam A (to stacker bin)	230
482.01 Sensor (diverter gate) static jam B (to top bin)	231
482.03 Sensor (diverter gate) late jam	232
483.01 Sensor (buffer path) static jam	233
483.03 Sensor (buffer path) late jam	234
484.01 Sensor (compiler media present) static jam	236
485.01 Sensor (upper media exit) static jam	237
485.03 Sensor (upper media exit) late jam	238
485.05 Sensor (upper media exit) lag jam	239
486.01 Sensor (lower media exit) static jam	240
486.03 Sensor (lower media exit) late jam	241
486.05 Sensor (lower media exit) lag jam	242
487.05 Sensor (compiler media present) late jam	244
491.01 Sensor (booklet media entrance) static jam	246
491.03 Sensor (booklet media entrance) late jam	246
491.05 Sensor (booklet media entrance) lag jam	248
492.01 Sensor (booklet compiler media present) static jam	249
493.01 Sensor (booklet media exit) static jam	250
493.03 Sensor (booklet media exit) static jam	251
493.05 Sensor (booklet media exit) lag jam	252
849.00 Hard drive failure	253
910.02–910.07 Data communication error	254
939.00 RIP card assembly communication failure	254
940.02 Clock signal communication error	255
940.03 Controller communication failure	255
940.04 IM logic failure	255
951.xx RIP card assembly NVRAM failure	256
953.xx Operator panel assembly NVRAM failure	256
955.xx RIP card assembly NAND CRC failure	256
956.00 RIP card assembly processor failure	257
956.01 RIP card assembly processor over temperature failure	257
956.02 RIP card assembly cooling fan failure	257
956.03 RIP card assembly FPGA failure	258
980.04 Duplex controller card assembly communication failure	258
980.05 Engine flicker communication failure	259
957.01 BITZ1 initialize failure	259
957.02 BITZ2 initialize failure	259
995.00 Finisher NVM R/W failure	260
996.00 Finisher type failure	260
997.00 Duplex controller card assembly type failure	260
999.00 Finisher engine/RIP functional failure	261
Image quality troubleshooting	262
Printer-related troubleshooting	262
Image Quality	263
3. Diagnostic aids	289
User operator panel, menus and messages	289
Understanding the operator panel	289
Understanding the home screen	290
Menu map	291
Accessing service menus	292
Configuration Menu	293
Entering Configuration Menu	293
Available settings	293
Action for prompts	294
Automatic Alignment Adjust Calibration	294
Automatically Display Error Screens	295
Black Only Mode	295
Booklet Adjustments	295
Clear Custom Status	295
Color Trapping	295
Disk Encryption	295
Energy Conserve	296
Envelope Prompts	296
Erase all Information on Disk	296
Exit Tray 2	296
Factory Defaults	296
Font Sharpening	297
Jobs on Disk	297
Key Repeat Initial Delay	297
Key Repeat Rate	297
Panel Menus	298
Paper Prompts	298
PPDS Emulation	298
Print Quality Pages	298
REGISTRATION	298
Reports	299
Require Standby	299
Reset Maintenance Counter Value	299
Short-edge Printing	299
Size Sensing	300
Tray Insert Message Delay	300
UI Automation	300
USB Speed	301
Wipe All Settings	301
Diagnostics Menu	302
Entering Diagnostics Menus	302
Available tests	302
DEVICE TESTS	304
DUPLEX TESTS	304
EVENT LOG (Diagnostics Menu)	305
FINISHER TESTS	306
HARDWARE TESTS	306
INPUT TRAY TESTS	307
MOTOR TESTS	308
OUTPUT BIN TESTS	309
PRINT TESTS	310
PRINTER SETUP	310
REPORTS	311
SENSOR TESTS	311
Service Engineer (SE) Menu	314
Print SE Menus	314
Paper jams	315
Avoiding jams	315
Understanding jam numbers and locations	316
Security Reset Jumper	339
Printer theory of operations	340
Print engine theory	340
Paper path theory	348
Color theory	355
Finisher theory of operations	359
Media transport	359
Functions of sensors along the media path	367
Punch unit	369
Compiler unit assembly	372
Stapler	377
Booklet Operation	381
Functions of booklet sensors and motors	382
Booklet media bin	384
Stacker media bin	384
Booklet tray	388
Power supply and interlock	389
TTM theory of operations	391
Media transport	392
Media tray assembly	392
TTM media feed units	394
Main components	395
3TM theory of operations	398
Media transport	399
Media tray assembly	399
3TM media feed units	400
Main components	401
1TM theory of operations	404
Media transport	405
Media tray assembly	405
1TM media feed units	406
Main components	407
High capacity feeder theory of operations	410
Media feeding	410
HCF media feed unit assembly operation	411
HCF media transport roll assembly operation	413
HCF media feed unit assembly sensor/motor functions	413
Status monitoring	414
4. Repair information	421
Handling ESD-sensitive parts	421
Turning the printer off	421
Removal procedures	422
Cover removal procedures	423
Inner cover removal	423
Internal rear cover removal	425
Left rear lower cover removal	426
Left upper cover removal	426
MPF top cover removal	427
Operator panel front cover (SFP)	428
Operator panel top cover (SFP) removal	428
Printer front door removal	430
Printer right cover removal	431
Printer top cover removal	432
Rear lower cover removal	434
Rear upper cover removal	436
Top rear cover (SFP) removal	437
Print engine removal procedures	440
1st transfer conductor housing removal	440
1st transfer retract clutch assembly removal	442
2nd transfer roller removal	444
ATC sensor PCB bracket removal	445
ATC sensor PCB removal	446
Bridge PCBA removal	448
C toner auger removal	451
Charge roll HVPS cooling fan removal	454
Charge roll HVPS PCBA removal	456
CMYK toner dispense auger assembly removal	457
Controller cooling fan removal	460
Developer carrier removal and replacement	462
Developer housing (C) removal	465
Developer housing (K) removal	471
Developer housing (M) removal	476
Developer housing (Y) removal	482
Developer housing rear plunger removal	487
Developer HVPS PCBA removal	489
Feeder slide guide removal	491
Front left cooling fan removal	492
Front right cooling fan removal	494
Front upper cooling fan removal	496
Fuser assembly removal	498
Fuser cooling fan removal	498
Fuser driver PCBA cooling fan removal	501
Fuser driver PCBA removal	504
Fuser pressure roll retract motor removal	508
Fuser/lower redrive/1st BTR retract motor removal	511
Inner plate removal	512
K toner auger removal	514
LED printhead removal	516
Lower engine PCBA removal	518
Lower redrive shift motor assembly removal	519
LVPS front fan guide removal	525
LVPS PCBA removal	526
LVPS sub cooling fan removal	529
M toner auger removal	530
Main power GFI interface removal	533
Main power switch removal	535
Media feed lift motor removal	535
Media out actuator removal	537
Media size switch PCB removal	537
Media transport/MPF drive motor removal	538
MPF roller removal	541
MPF tray feeder removal	542
Operator panel assembly (SFP) removal	543
Operator panel PCBA (SFP) removal	544
Operator panel speaker (SFP) removal	546
PC smart chip socket (C, M, Y, K) removal	548
PC/developer drive motor cooling fan removal	550
PC/developer drive motor removal	552
Pick roller removal	555
Printer left duplex door assembly removal	556
Printer media turn guide removal	557
Printer tray 1 feeder removal	558
Printhead retract door removal	559
Registration drive motor removal	561
Registration/transport roller assembly removal	563
RIP PCBA removal	564
Sensor (image calibration) removal	567
Sensor (media level) removal	568
Sensor (media on belt) removal	569
Sensor (media out) removal	570
Sensor (printer left duplex door interlock) removal	572
Sensor (printer left front door interlock) removal	574
Sensor (printer right front door interlock) removal	576
Sensor (tray 1 pre-feed) removal	577
Sub LVPS PCBA removal	578
Suction fan removal	581
Suction filter removal	583
Toner dispense motor removal	583
Toner smart chip PCB removal	586
Touch screen (SFP) removal	587
Transfer belt assembly removal	588
Transfer belt cleaner removal	592
Transfer belt lever removal	594
Transfer roll HVPS PCBA removal	595
Upper exhaust cooling fan removal	598
Upper printer engine PCBA removal	601
Upper redrive assembly removal	603
Waste toner agitator motor removal	605
Waste toner auger chute removal	608
Waste toner sensor guide removal	610
Waste toner shaft gate removal	611
Y toner auger removal	613
Tray module removal procedures	616
3TM left door removal	616
Sensor (media level) removal	617
Sensor (media out) removal	617
Sensor (media present) removal	618
Sensor (tray module feedout) removal	620
Sensor (tray module left door interlock) removal	621
Sensor (TTM media size) removal	623
Sensor (TTM tray 3 feedout) removal	623
Sensor (TTM tray 4 feedout) removal	624
Tray module bottom cover removal	625
Tray module controller PCBA removal	626
Tray module left cover removal	626
Tray module lower transport motor removal	627
Tray module media feeder removal	628
Tray module rear cover removal	631
Tray module right cover removal	631
Tray module top cover removal	632
Tray module transport rollers removal	633
Tray module tray 2 media turn guide removal	634
Tray module upper transport motor removal	634
TTM left door removal	635
TTM lower transport motor removal	636
TTM tray 3 feeder removal	637
TTM tray 3 media tray removal	640
TTM tray 3 media turn guide removal	641
TTM tray 4 media feeder removal	641
TTM tray 4 media transport removal	644
TTM tray 4 media tray removal	645

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1,000
1,001
1,002
1,003
1,004
1,005
1,006

Match case Limit results 1 per page

Diagnostic aids

3-125

5058-030

Go Back

HCF media transport roll assembly operation

Upon receiving the feed start signal from the controller the HCF activates the HCF transport motor at a high

speed after a preset time has passed. This rotating power of the HCF transport motor is transmitted to the HCF

media transport roll assembly, and the media from the HCF media feed unit assembly is transferred to the

printer.

When the sensor (tray 5 feed-out) is turned on by the media fed with the HCF media transport roll assembly, the

HCF transport motor speed decreases after a preset time has passed.

When the sensor (registration) in the printer is turned on by the media fed from the HCF, the HCF transport

motor turns off.

When the next feed start signal is received, before the HCF transport motor is turned off, the transport motor

continues to rotate.

Thus, media is transferred from the HCF media transport roll assembly to the laser printer.

HCF media feed unit assembly sensor/motor functions

Functions of the sensors and motors of the media feed unit assembly are outlined below.

•

HCF media feed lift motor

—is a stepping motor that rotates (forward) the pick roll and feed roll to send

media from the tray to the HCF media transport roll assembly. The motor also lifts the tray by reverse

rotation.

•

HCF pick solenoid

—Raises or lowers the pick roll. The HCF pick solenoid stays activated from the

beginning of media feed until the sensor (pre-feed) turns on. The HCF pick solenoid is activated when the

tray is inserted and when the power is turned on to check the presence of media in the tray.

•

Sensor (pre-feed)

—Detects whether media has been fed from the tray, and controls the HCF feed lift

motor speed. The sensor also becomes a trigger to deactivate the HCF pick solenoid. The sensor turns on

upon detecting media, and determines that media is present.

•

HCF transport motor

—is a stepping motor that rotates the HCF media transport roll assembly to feed

media to the printer.

•

Sensor (tray 5 feed-out)

—Detects whether media has been fed from the tray, becomes a trigger to stop

the HCF feed lift motor, and controls the HCF transport motor speed.

Media

HCF media transport

roll assembly

Sensor (tray 5 feed-out)

HCF transport motor