Lexmark CS310 Quick Reference

Lexmark CS310 Manual

Get Lexmark CS310 PDF manuals and user guides View all Lexmark CS310 manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark CS310 manual content summary:

  • Lexmark CS310 | Quick Reference - Page 1
    green Solid green Blinking red Printer status The printer is off or in Hibernate mode. The printer is warming up, processing data, or printing. The printer is on, but idle. The printer requires user intervention. Sleep button light color and its corresponding printer status Sleep button light Off
  • Lexmark CS310 | Quick Reference - Page 2
    feeder and manual feeder. • The largest supported Universal size is 215.9 x 359.9 mm (8.5 x 14.17 inches) and is loaded only in the multipurpose feeder and manual feeder. 1 From the printer control panel, navigate to: > Paper Menu > > Universal Setup 2 Press the arrow buttons until Units
  • Lexmark CS310 | Quick Reference - Page 3
    jams and print quality problems. Loading the 650‑sheet duo tray The 650‑sheet duo tray (Tray 2) consists of a 550‑sheet tray and an integrated 100‑sheet multipurpose feeder. The tray is loaded in the same way as the 250‑sheet tray and the optional 550‑sheet tray, and supports the same paper types
  • Lexmark CS310 | Quick Reference - Page 4
    , or self‑stick adhesives. These envelopes may severely damage the printer. 2 Open the multipurpose feeder. 4 Prepare the paper for loading. • Flex sheets of the paper guides. 2 1 5 3 Pull the multipurpose feeder extender. Note: Guide the extender gently so that the multipurpose feeder is fully
  • Lexmark CS310 | Quick Reference - Page 5
    the right side of the paper guide. 2 Feed paper into the manual feeder only to the point where its leading edge can contact the paper guides. Note: To achieve the best possible print quality, use only high‑quality media designed for laser printers. 3 Adjust the paper guides to the width of the paper
  • Lexmark CS310 | Quick Reference - Page 6
    necessary. d Click OK > Print. For Macintosh users a Customize the settings in the Page Setup dialog: feeder. 3 Click Print. Printing in black and white From the printer control panel, navigate to: > Settings > > Print Settings > > Quality menu > > Print Mode > > Black Only > Adjusting toner
  • Lexmark CS310 | Quick Reference - Page 7
    and a higher toner yield. • Max Speed-This lets you print in either black or color depending on what is set in the printer driver. The printer prints in color unless Black Only is selected in the printer driver. • Max Yield-This lets you switch from black to color based on the color content found on
  • Lexmark CS310 | Quick Reference - Page 8
    and straighten paper before loading it. • Make sure the guides in the tray or the multipurpose feeder are properly positioned and are not pressing tightly against the paper or envelopes. • Push the tray firmly into the printer after loading paper. Use recommended paper • Use only recommended paper
  • Lexmark CS310 | Quick Reference - Page 9
    out the standard 250-sheet tray (Tray 1) and manual feeder. 4 From the printer control panel, press and continue printing. to clear the message [x]‑page jam, clear multipurpose feeder. [250.xx] 1 Push the paper release lever in the multipurpose feeder to access the jammed paper, and then gently
  • Lexmark CS310 | Quick Reference - Page 10
    4 Slide the paper guide until it lightly rests against the edge of the paper stack. 2 From the printer control panel, press and continue printing. to clear the message [x]‑page jam, open front door. [20y.xx] 1 Open the front door. CAUTION-HOT SURFACE: The inside of the printer might be hot. To
  • Lexmark CS310 | Quick Reference - Page 11
    it out. Note: Make sure all paper fragments are removed. 4 From the printer control panel, press and continue printing. to clear the message [x]‑page jam, xx] 1 Open the front door. CAUTION-HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot component,
  • Lexmark CS310 | Quick Reference - Page 12
    4 Close the front door. [x]‑page jam, open tray [x] [24y.xx] 1 Pull the tray out completely. Note: The message on the printer display determines in which tray the paper jam is located. 2 Firmly grasp the jammed paper on each side, and then gently pull it out. Note:
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
Quick Reference
Learning about the printer
Using the printer control panel
2
1
3
8
7
4
9
6
5
Use the
To
1
Menus button
Open the menus.
Notes:
•
The menus are available only when the
printer is in Ready state.
•
Pressing the button while in a menu
item lets you return to the top level
menu screen.
2
Display
View printing options as well as status and
error messages.
3
Sleep button
Enable Sleep mode or Hibernate mode.
Notes:
•
Pressing any hard button, sending a
print job, or performing a power on
reset with the main power switch
wakes the printer from Sleep mode.
•
Pressing the Sleep button or
performing a power on reset with the
main power switch wakes the printer
from Hibernate mode.
4
Stop button
Stop printer activity.
Use the
To
5
Right arrow
button
•
Scroll through menus or move between
screens and menu options.
•
Increase the numeric value of an option
or setting being displayed.
6
Select button
•
Select menu options.
•
Save settings.
7
Left arrow
button
•
Scroll through menus or move between
screens and menu options.
•
Decrease the numeric value of an option
or setting being displayed.
8
Back button
Return to the previous screen.
9
Indicator light
Determine the status of the printer.
Understanding the colors of the indicator
and Sleep button lights
The colors of the indicator and Sleep button lights on the printer control
panel signify a certain printer status or condition.
Indicator light color and its corresponding printer status
Indicator light
Printer status
Off
The printer is off or in Hibernate mode.
Blinking green
The printer is warming up, processing data,
or printing.
Solid green
The printer is on, but idle.
Blinking red
The printer requires user intervention.
Sleep button light color and its corresponding printer status
Sleep button light
Printer status
Off
The printer is idle or in Ready state.
Solid amber
The printer is in Sleep mode.
Blinking amber
The printer is waking from or entering
Hibernate mode.
Sleep button light
Printer status
Blinking amber for 0.1
second, then goes
completely off for 1.9
seconds in pulsing
pattern
The printer is in Hibernate mode.
Using the Embedded Web Server
Note:
This feature is available only in network printers or printers
connected to print servers.
If the printer is installed on a network, then you can use the Embedded
Web Server to do the following:
•
View the virtual display of the printer control panel.
•
Check the status of the printer supplies.
•
Configure supply notifications.
•
Configure printer settings.
•
Configure network settings.
•
View reports.
To access the Embedded Web Server for your printer:
1
Obtain the printer IP address:
•
From the TCP/IP section in the Network/Ports menu
•
By printing a network setup page or menu settings page, and
then finding the TCP/IP section
Notes:
–
An IP address appears as four sets of numbers separated
by periods, such as 123.123.123.123.
–
If you are using a proxy server, then temporarily disable
it to load the Web page correctly.
2
Open a Web browser, and then type the printer IP address in the
address field.
3
Press
Enter
.
The Embedded Web Server page appears.
1