Lexmark E260D Service Manual

Lexmark E260D - Taa/gov Compliant Manual

Get Lexmark E260D - Taa/gov Compliant PDF manuals and user guides
UPC - 734646084079
View all Lexmark E260D manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark E260D manual content summary:

  • Lexmark E260D | Service Manual - Page 1
    Lexmark™ E260, E260d, E260dn 4513-200 4513-220 4513-230 • Table of contents • Start diagnostics • Safety and notices • Trademarks • Index Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
  • Lexmark E260D | Service Manual - Page 2
    technical inaccuracies or typographical errors. Changes are periodically made services, except those expressly designated by the manufacturer, are the user's responsibility. Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered in the United
  • Lexmark E260D | Service Manual - Page 3
    2-3 Common primary light patterns 2-4 Primary codes 2-7 Common secondary light patterns 2-16 Secondary error codes 2-18 Service codes 2-28 Messages and error codes 2-36 User attendance messages 2-36 Paper jam error codes (200-series 2-36 Service error codes 2-42 Diagram of the printer menus
  • Lexmark E260D | Service Manual - Page 4
    exit guide assembly with sensor and reversing solenoid removal 4-48 Right side cover assembly removal 4-50 Top cover assembly removal 4-52 Transfer roll removal 4-54 Wear strip (tray 1 and 250-sheet tray 2) removal 4-55 Wear strip (550-sheet tray 2) removal 4-56 iv Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 5
    5-1 Locations 5-1 Front view 5-1 Rear view 5-1 Controller board connector pin values 5-2 Preventive maintenance 6-1 Safety inspection guide 6-1 Lubrication specifications 6-1 Parts catalog 7-1 How to use this parts catalog 7-1 Index I-1 Part number index I-3 Table of Contents v
  • Lexmark E260D | Service Manual - Page 6
    4513-200, -220, -230 vi Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 7
    in the wavelength region of 655-675 nanometers. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition. Laser Der Drucker erfüllt gemäß amtlicher Bestätigung der
  • Lexmark E260D | Service Manual - Page 8
    laser, som arbejder på bølgelængdeområdet 655-675 nanometer. Lasersystemet og printeren er udformet således, at mennesker aldrig udsættes for en laserstråling over Klasse I-niveau ved normal drift, brugervedligeholdelse eller obligatoriske servicebetingelser. viii Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 9
    utsätts för laserstrålning över Klass I-nivå vid normal användning, underhåll som utförs av användaren eller annan föreskriven serviceåtgärd. Laser-melding Skriveren er godkjent i USA etter kravene i DHHS 21 CFR, underkapittel J, for klasse I (1) laserprodukter, og er i andre land godkjent som et
  • Lexmark E260D | Service Manual - Page 10
    4513-200, -220, -230 Avís sobre el Làser Segons ha estat certificat als Estats Units, aquesta impressora compleix els requisits de DHHS 21 CFR, apartat J, pels productes làser de de manteniment d'usuari ni durant els serveis que satisfacin les condicions prescrites. x Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 11
    4513-200, -220, -230 Notices and safety information xi
  • Lexmark E260D | Service Manual - Page 12
    4513-200, -220, -230 xii Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 13
    components. The manufacturer is not responsible for safety in the event of use of unauthorized replacement parts. • The maintenance information for this product has been prepared for use by a professional service person and is not intended to be used by others. • There may be an increased risk
  • Lexmark E260D | Service Manual - Page 14
    y tomar las precauciones necesarias. • PRECAUCIÓN: este símbolo indica que el voltaje de la parte del equipo con la que está trabajando es peligroso. Antes de empezar, desenchufe el equipo estar ligado à corrente eléctrica para realizar a tarefa necessária. xiv Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 15
    producte. El personal professional ha d'estar-ne assabentat i prendre les mesures convenients. • PRECAUCIÓ: aquest símbol indica que el voltatge de la part de l'equip amb la qual esteu treballant és perillós. Abans de començar, desendolleu l'equip o extremeu les precaucions si, per treballar
  • Lexmark E260D | Service Manual - Page 16
    test points on the printer. 6. Preventive maintenance contains the lubrication specifications and recommendations to prevent problems. 7. Parts catalog contains illustrations and part numbers for individual FRUs. Conventions Note: A note provides additional information. Warning: A warning identifies
  • Lexmark E260D | Service Manual - Page 17
    , -6EW service manual. Maintenance approach The diagnostic information in this manual leads to the correct field replaceable unit (FRU) or part. Use the error code charts, symptom index, and service checks to determine the symptom and repair the failure. See "Diagnostics information" on page 2-1 for
  • Lexmark E260D | Service Manual - Page 18
    4513-200, -220, -230 Overview of the operator panel The operator panel consists of these items: • LED operator panel • Two buttons: Cancel and Continue • Six lights: Error , Paper Jam , Load Paper , Toner Low , Ready , and Continue 1-2 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 19
    cards (DBCS) Option slots Memory slots Flash memory/option card Print quality settings 4513-200, -220 Lexmark E260, E260d 32MB 160MB  x x x x  1 x 4513-230 Lexmark E260dn 32MB 160MB  x x x x  1 x Item 4513-200, -220 Lexmark E260, E260d 4513-230 Lexmark E260dn Print resolution 1200 Image
  • Lexmark E260D | Service Manual - Page 20
    connections:   external print server support *All models are USB 2.0 Certified devices supporting Hi-Speed data transfer. ¹ Includes the HD photo image format ² Includes support for the following graphics formats: TIFF, TIF, JPG, GIF, PNG, BMP, PCX, AND DCX 1-4 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 21
    4513-230 Lexmark E260dn  x  Optional input sources 250-sheet drawer   550-sheet drawer   Manual/integrated print duplex Integrated Integrated Envelope conditioning x x Available output trays Standard 150-sheet sensing bin   Toner and photoconductor Toner cartridge 1,000
  • Lexmark E260D | Service Manual - Page 22
    appears in that source's list of supported media sizes. These values only appear in a source's list of supported media sizes either when the source is non-size sensing or when the source's size sensing hardware is deactivated and then the device is power cycled. 1-6 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 23
    Tips on preventing jams Paper path I J 4513-200, -220, -230 F G E H K L A Paper path B Manual feed sensor C Upper end feed rolls D Input sensor E Transfer roll F Fuser G Fuser exit rolls H Fuser exit sensor I Exit rolls J Exit sensor K Duplex unit L Duplex sensor M
  • Lexmark E260D | Service Manual - Page 24
    on the 250-sheet tray before pushing the tray into the printer. • Make sure paper guides are positioned before loading the paper or specialty media. • Do not remove trays while a job nose pliers • Volt-ohmmeter • #1 and #2 Phillips screwdriver • Slotted screwdriver 1-8 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 25
    Power Supply Liquid Crystal Diode Light Emitting Diode Laser Scanning Unit Low Voltage Power Supply Nonvolatile Random Access Memory Photoconductor Printer Control Language Power-On Reset Power-On Self Test Personal Printer Data Stream People's Republic of China Toner Add Roll Synchronous Dynamic
  • Lexmark E260D | Service Manual - Page 26
    4513-200, -220, -230 1-10 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 27
    of a problem, see "Diagram of the printer menus" on page 2-48. • Information from the operator panel of the printer. - Models E260, E260d, and E260dn have an operator panel containing lights and buttons. Warning: Paper clips are commonly used near printers and can become lodged in the paper path
  • Lexmark E260D | Service Manual - Page 28
    fuser) and then stays on. 4. If there is a problem in the printer such as a paper jam, then the panel lights indicate the problem. See "Common primary light patterns" on page 2-4 for more information. 5. The printer cycles down into standby mode, and lights solid. 2-2 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 29
    (see "Service tertiary error codes" on page 2-30) indicate specific errors. See "Service codes" on page 2-28. Note: If data is sent to the printer and all lights flash immediately, and double-clicking does not change the display, then there may be a code problem. Contact the next level of support
  • Lexmark E260D | Service Manual - Page 30
    cartridge invalid refill Missing or defective print cartridge Unsupported print cartridge Photoconductor kit life warning¹ 12   Programming engine code/ 13 Programming system code    Service error² 13       Printer error³ 13   2-4 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 31
    Condition Page Paper jam printer error (2xx) 14   Remove paper from output bin 14  Load media in Tray 1 or Tray 2 14   Load Media in Multi-purpose 15  Feeder or Manual Feeder Load Tray 1 for side 2 of manual 15   duplex printing ¹ Toner low light will remain flashing with
  • Lexmark E260D | Service Manual - Page 32
    buffer  and Replace Photoconductor Device is printing and Replace Photoconductor Waiting and Replace Photoconductor Not Ready and Replace Photoconductor Replace Photoconductor IR          x               2 -6 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 33
    codes Ready/Power Saver 4513-200, -220, -230  Meaning • The printer is ready to receive and process data. • The printer is in Power Saver mode. Action • Send a print job. • Press Continue to print the menu settings pages for a list of current printer settings. • Press and hold Cancel to reset
  • Lexmark E260D | Service Manual - Page 34
    Meaning The printer is waiting until a print timeout occurs, or until it receives additional data. Action • Press Continue to print the contents of the print buffer. • Press and release Cancel to cancel the print job. • Press and hold Cancel to reset the printer. 2-8 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 35
    to 300 dpi to prevent a memory full error. Action • Wait until the control panel returns to Ready to print other jobs. • Press and release Cancel to cancel the print job. • Press and hold Cancel to reset the printer. Not ready (printer is offline)  Meaning The printer is not ready to receive or
  • Lexmark E260D | Service Manual - Page 36
    has been installed that is not supported. Action Close the door, install a print cartridge, or install a supported flash option. The printer will automatically reset. Insufficient collation area/Insufficient memory   Meaning The printer memory is too full to collate the print job. Action
  • Lexmark E260D | Service Manual - Page 37
    a Memory Full error. Action Pressing Cancel will cancel the print job. Other buttons are ignored. Toner low   Meaning The printer is ready to receive and process data. In addition, the toner in the toner cartridge is getting low. Action • Press and release Continue to clear the light
  • Lexmark E260D | Service Manual - Page 38
    Meaning The photoconductor kit is full and must be replaced. The printer will not print any more pages until the photoconductor kit is replaced. Action • Press and release Continue to print a photoconductor kit instruction page. • Replace the photoconductor kit. 2-12 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 39
    -230    Meaning New code is being programmed into the engine or firmware code flash. Action Wait for the message to clear. When the printer has finished programming the code, it performs a soft reset. Service error       Meaning The printer has a service error, and printing
  • Lexmark E260D | Service Manual - Page 40
    to clear the error code. Load media in Tray 1 or Tray 2   Meaning The printer is out of print media at the indicated source. Action • Load print media into the indicated tray, and press Continue to resume printing. • Press Cancel to reset the printer. 2-14 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 41
    media in the multi-purpose feeder or manual feeder. Action • Load print media into the manual feeder. • Press Continue to resume printing. • Press Cancel to reset the printer. Load media Tray 1 for Side 2 of manual duplex printing   Meaning The printer prompts to load side 2 of a single sheet
  • Lexmark E260D | Service Manual - Page 42
    error code light sequence. The following table shows what these light sequences mean and where to go for help. Common light sequences for paper jams When the Paper jam secondary error code. and Continue lights are both on, a paper jam has occurred with a Printer Condition Page 200: Paper jam
  • Lexmark E260D | Service Manual - Page 43
    error code light sequence. The following table shows what these light sequences mean and where to go for help. Printer Condition Page Complex page 20  Insufficient collation area 21  Defective flash 21  Network interface errors 21   Resource save off-deficient 22  memory
  • Lexmark E260D | Service Manual - Page 44
       Meaning A paper jam has occurred. The jammed media is most likely in the fuser area under the toner cartridge assembly. Action Open the front door, remove the print cartridge, and clear the paper jam. 202: Paper jams as a printed job exits the printer    Meaning A paper jam has
  • Lexmark E260D | Service Manual - Page 45
    before Action Remove the tray, open the duplex door and clear the paper jam. 234: Paper jam (duplex - unknown location)    Meaning A paper jam has occurred somewhere around the duplex unit before making the manual input sensor. Action Remove the tray, open the duplex door and clear the
  • Lexmark E260D | Service Manual - Page 46
    this error in the future: • Reduce the complexity of the page by reducing the amount of text or graphics on the page and deleting unnecessary download fonts or macros. • Set Page Protect to On in the Local Printer Setup Utility. • Install additional printer memory. 2-20 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 47
    to reset the printer. To avoid this error in the future: • Simplify the print job. Reduce the complexity of the page by reducing the amount of text or graphics on the page and deleting unnecessary downloaded fonts or macros. • Install additional printer memory. Defective Flash    Meaning
  • Lexmark E260D | Service Manual - Page 48
    to reset the printer. To avoid this error in the future: • Simplify the print job. Reduce the complexity of the page by reducing the amount of text or graphics on the page and deleting unnecessary downloaded fonts or macros. • Install additional printer memory. 2-22 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 49
    hold Cancel to reset the printer. To avoid this error in the future: • Simplify the print job. Reduce the complexity of the page by reducing the amount of text or graphics on the page and deleting unnecessary downloaded fonts or macros. • Install additional printer memory. Diagnostics information
  • Lexmark E260D | Service Manual - Page 50
    written to flash will be deleted. Invalid engine code    Meaning The engine code has not been programmed, or the programmed code is not valid. Action Download the valid engine code to the internal print server while this message is still on the panel. 2-24 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 51
    toner cartridge. Action Remove the toner cartridge, and install a new toner cartridge that matches the region of the printer. The settings cannot be changed without calling Lexmark for a one-time change. Change toner cartridge/invalid refill    Meaning The toner in the toner cartridge
  • Lexmark E260D | Service Manual - Page 52
    it with a supported toner cartridge. • Turn the printer on. Too many options attached     Meaning This message indicates that to too many flash options have been attached. Action Press Continue briefly to clear the message. The option will be ignored. 2-26 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 53
    marked as bad, and normal operation will continue. Flash operations will not be allowed until flash is formatted. Install MICR cartridge    Meaning The printer has detected that it requires the installation of a MICR cartridge in order to complete a print job that it has received. Action
  • Lexmark E260D | Service Manual - Page 54
    Codes Secondary Codes Service primary code  Light blinking When this code appears, double-click to reveal the secondary codes. Service primary code Tertiary Codes Lights Primary code for service errors See service secondary error codes       2-28 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 55
    secondary codes 4513-200, -220, -230 Lights 90x: Software  90x: Software    91x: DC motor or transfer roll   92x: Fuser or toner sensor   93x: Printhead, drive motor    94x: LVPS service error   95x: Controller board (NCRAM, ROM, or NAND)    96: RAM memory
  • Lexmark E260D | Service Manual - Page 56
    which allows the printer to temporarily recover from the error. These error codes are recorded in the history file which can be reviewed through the Diagnostics Menu. See "Diagnostics mode selections" on page 3-8. Note: All service errors are initially communicated by all lights flashing which is
  • Lexmark E260D | Service Manual - Page 57
    a problem in the fuser, a stalled fan motor, or a faulty toner sensor or toner cartridge. Multiple errors indicate replacing the corresponding part. Service tertiary error codes: fuser, fan, or toner sensor Lights Service secondary codes: 92x   Service tertiary codes: fuser, fan, or toner
  • Lexmark E260D | Service Manual - Page 58
    . Error codes 948-949 indicate engine card failure. Lights Service secondary codes: 94x Service tertiary codes: RIP engine communicator or engine card 940: LVPS or cable has failed 948: Service engine card failure 949: Service engine card failure       2-32 Lexmark™ E260, E260d
  • Lexmark E260D | Service Manual - Page 59
    a problem in the NVRAM (nonvolatile random access memory). Replace the operator panel assembly. Codes 955-959 indicate a failed controller board assembly. Replace the controller board. Service tertiary error codes: NVRAM failure Lights Service secondary codes: 95x    Service tertiary codes
  • Lexmark E260D | Service Manual - Page 60
    Flash parts failed while programming port    Paper port communication error Indicates a communication error in the paper port. Lights Service secondary codes: 98x Service tertiary codes: paper port communication error 980: Service paper port communication failure  981: Service paper
  • Lexmark E260D | Service Manual - Page 61
    Indicates a failure with the device's equipment or controller board. Lights Service secondary codes: 99x Service tertiary codes: device equipment check or device controller board error 990: Service device equipment check 991: Service device controller board failure  4513-200, -220, -230
  • Lexmark E260D | Service Manual - Page 62
    problems that must be resolved. This topic provides a list of all printer messages and explains what they mean. User attendance messages Cartridge error codes Error 30 31 32 Description Invalid refill Missing or defective cartridge Unsupported cartridge Action Replace the cartridge. Paper jam
  • Lexmark E260D | Service Manual - Page 63
    -220, -230 Paper jam error codes (200-series) (Continued) Error Description Action 200.08 manual input sensor removal" on page 4-39. 200.19 The media never reached the input sensor, but was detected at manual feeder sensor. Remove the toner cartridge/PC kit, and inspect for debris in the paper
  • Lexmark E260D | Service Manual - Page 64
    collection during auto alignment 200.38 Interpage servo gap is smaller than expected for printhead offset target evaluation 200.42 Rogue sheet is at the manual feed sensor while flushing the paper path prior to declaring MPF source empty. Retry alignment. 2-38 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 65
    the wear strips. 201.00 Paper jam between input and exit sensor Remove the toner cartridge/PC kit and check for obstructions between the input sensor and the fuser. if the media continues to stop at the entrance or in the fuser, then replace the fuser. See "Fuser removal" on page 4-20. 201.01
  • Lexmark E260D | Service Manual - Page 66
    pages printed since calling a 241.10 or a prior 241.19. 242.00 Paper jam near tray 2. Remove Tray 2 and inspect for obstruction in the paper path. Check the pick tires for wear or paper dust. Replace if necessary. Check the wear strips and replace if necessary. 2-40 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 67
    if necessary. Check the wear strips and replace if necessary. 251.00 251.10 251.11 Paper jam near the manual feeder. Second pick attempt failed from manual feeder. Failed to feed from manual feeder. Pages in the paper path have been flushed to the output bin. Inspect the pick roller on the MPF or
  • Lexmark E260D | Service Manual - Page 68
    service check" on page 2-51 914.01 Lost encoder feedback Transfer service errors 917.xx Transfer service error Fuser service errors 920.00 Under temperature during steady state control. 920.01 Fuser took too long to heat up after transitioning to new . 2-42 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 69
    and belt fusers. 925.xx Wrong fuser installed. The fuser type stored in the cartridge ID does not match the actual fuser installed in the printer. Fan service errors 927.00 927.03 Service fan error Main fan took too long to ramp up Replace the fan. See "Cooling fan service check" on page 2-52
  • Lexmark E260D | Service Manual - Page 70
    start 936.02 No lock detected at motor start for motor ID Replace the main motor gear drive. See "Main motor service check" on page 2-54 936.03 No halls detected at motor start 936.04 Failed to stop within timeout 936.05 Stall detected during speed control 2-44 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 71
    MVRAM Cyclic Redundancy Check error Performing POR will clear this error. occurred. 953.xx NVRAM chip failure with mirror Replace the operator panel. See "Operator panel service check" on page 2-55. 954.xx 955.xx NVRAM chip failure with system part. The code ROM or NAND flash failed the Cyclic
  • Lexmark E260D | Service Manual - Page 72
    resolve the problem, then replace the firmware card and download the emulation again. Network errors 975.xx Unrecognizable network Call the next level of support. 976.xx Unrecoverable software error in network port 978.xx Bad checksum while programming network port 979.xx Flash parts failed
  • Lexmark E260D | Service Manual - Page 73
    4513-200, -220, -230 Service error codes (9xx) (Continued) Error Description Action 984.xx 990.xx 991.xx Invalid command parameter received by the specidied device specified device has detected an equipment check in its system card. Call the next level of support. Diagnostics information 2-47
  • Lexmark E260D | Service Manual - Page 74
    Saver Resource Save Download Target Print Timeout Wait Timeout Auto Continue Jam Recovery Page Protect Print Area Job Menu Cancel Job Reset Printer Print Buffer Quality Menu Print Resolution Toner Darkness PictureGrade™ PPDS Menu Orientation Lines per Page Lines per Inch Page Format Character Set
  • Lexmark E260D | Service Manual - Page 75
    on. None of the lights come on. Main motor does not come on. Fan does not come on. Fuser does not cycle. Fuser does not turn on and off. The paper feed picks and tries to feed media. Action See "Cover interlock switch service check" on page 2-52. See "Operator panel service check" on page 2-55. See
  • Lexmark E260D | Service Manual - Page 76
    not working. Fuser parts melted. Toner not fused to the media. Paper jams. Main motor noisy or not moving. Media skew. Printer not communicating with host. Front access door will not close. Operator panel button not responding. Operator panel lights are off or very dim. Blank page. Black page. Heavy
  • Lexmark E260D | Service Manual - Page 77
    for more information. Controller board service check Controller board service check FRU Controller board assembly Warning: Do not replace the operator panel and controller board at the same time. Each card contains the printer settings. When either of these cards is new, it obtains some of the
  • Lexmark E260D | Service Manual - Page 78
    . • If both pass continuity, then turn the printer on, and measure +5 V dc on pin 2 at J7 on the controller board. • Verify pin 3 at J7 is ground. • If voltage or ground is not present, then see "Controller board service check" on page 2-51 for more information. 2-52 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 79
    are correct, then check the controller board. See "Controller board removal" on page 4-6. Fuser service check When toner is partially fused to the media, it is usually caused by low fuser temperature. The line voltage to the printer must be within the following limits: • 100 V ac: 127 V ac for the
  • Lexmark E260D | Service Manual - Page 80
    does not exist on one or more of the wires, then call the next level of support. • If these voltages are not correct, then see "Controller board connector pin values" on page 5-2, or replace the controller board. See "Controller board removal" on page 4-6. 2-54 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 81
    check" on page 2-51. Buttons If the buttons do not respond, then replace the operator panel. There is no test or repair for the faulty switches on the operator panel. Paper feed service checks Paper jam error indication during POST FRU Fuser (exit sensor) Input/duplex sensor Manual feed sensor
  • Lexmark E260D | Service Manual - Page 82
    replace the solenoid. • If the resistance is approximately 70 ohms, then check the controller board. Pin 1 at J26 should be +24 V dc. See "Controller board service check" on page 2-51 for more information. Replace controller board as necessary. 2-56 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 83
    . Some, such as card stock or rough texture, may require a higher fuser temperature, which leads to more of these problems (except stacking) in plain paper. • Change settings using the printer driver. • Use the local printer setup utility (included on the CD) to change the NVRAM settings. Try
  • Lexmark E260D | Service Manual - Page 84
    . • If there is no continuity, then call the next level of service. Try a different toner cartridge and PC kit. • If those fail, then replace the LVPS/HVPS, controller board, or the printhead in that order. Also, see "Solving print quality problems" on page 3-62. 2-58 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 85
    Check the toner darkness setting in the driver. Try a lower setting. Make sure the toner cartridge and PC Kit are correctly installed and the high voltage contacts are clean. If the toner cartridge and PC Kit are installed correctly, then try a new PC Kit first and then toner cartridge. Check the
  • Lexmark E260D | Service Manual - Page 86
    temperature to fuse the toner to the paper. See"LVPS/HVPS service check" on page 2-54 for more information. Try changing the setting to heavier paper or even card stock. Make sure recommended media is being used. Check the media settings in the printer driver. 2-60 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 87
    . With the printer off, check to make sure that the laser beam is not blocked. Inspect the toner cartridge and paper feed components, especially the drive coupler and drive gears for debris, binds, or damage. Toner on back of page FRU Photoconductor kit (not a FRU) Fuser Transfer roll HVPS
  • Lexmark E260D | Service Manual - Page 88
    appear on the page. Vertical streaks Something could be caught between the PC kit and the fuser. Check the paper path around the fuser entry. Try a different toner cartridge. Vertical white lines may be caused by the laser beam, which may be partially blocked. With the printer off, clear the
  • Lexmark E260D | Service Manual - Page 89
    setting from the printer driver. • Try a different type of paper. Media designed for copiers gives the best quality. • Replace the toner cartridge. • The toner cartridge may be out of toner or defective. Replace the cartridge. • There may be a software error. Re-initialize the printer by turning it
  • Lexmark E260D | Service Manual - Page 90
    . • Check the feed tires. (See two preceding actions.) • The printer is waiting on the next command. • Clear all jams. • Press and release , or open and close the printer cover to restart the printer. • Make sure the toner cartridge assembly is installed properly. 2-64 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 91
    is on solid. While in PostScript 3 emulation, the printer is flushing data (Ready/Data and Error lights are blinking). • Ensure correct printer driver is being used. • Select hex trace mode to determine what the problem is. • Restore factory defaults. • Make sure the parallel cable or USB cable is
  • Lexmark E260D | Service Manual - Page 92
    pin values" on page 3-2 for the J28 connector. Pins 1, 4: 3.3 V Pin 2: 24 V Pin 6: Ground If the voltages are incorrent, then replace the controller board. If the voltages are correct, then try using Tray 2 again. If the printer error persists, then replace Tray 2. 2-66 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 93
    pressing and holding Continue until all of the lights flash, then release the button. The Ready/Data light will blink when the page is being formatted and printed. Note: The Configuration Mode Instruction page and Diagnostic menu page in this manual are samples only and may not match your specific
  • Lexmark E260D | Service Manual - Page 94
    4513-200, -220, -230 Configuration Menu printout (sample only; use actual sheet). Note: The light sequences change relative to the option on the printer. Lexmark E260d, E260dn Lexmark E260d, E260dn 3-2 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 95
    Diagnostics mode printout sample (sample only; use actual sheet) 4513-200, -220, -230 Lexmark E260d, E260dn Note: The light sequences change relative to the options on the printer. Diagnostic aids 3-3
  • Lexmark E260D | Service Manual - Page 96
    access door once the Error light displays. Print menus by pressing and holding until all of the lights flash. Utilities Use the Utilities menu to troubleshoot printer problems. Setting Reset Factory Defaults Hex Trace Print Quality Test Pages Reset Photoconductor Maintenance Counter Use setting to
  • Lexmark E260D | Service Manual - Page 97
    data is sampled on the leading (On) or trailing (Off) edge of strobe. Configure the printer to process Macintosh binary PostScript print jobs. Values Off On Auto (default) Standard Fastbytes (default) Off On (default) Off-The printer filters PostScript print jobs using Standard protocol. On-The
  • Lexmark E260D | Service Manual - Page 98
    printer processes raw binary PostScript print jobs from computers using the Macintosh operating system. This setting often causes Windows print jobs to fail. Auto (default)-The printer processes print jobs from computers using either Windows or Macintosh operating systems. 3-6 Lexmark™ E260, E260d
  • Lexmark E260D | Service Manual - Page 99
    printer and query printer status information Off simultaneously. Auto (default) MAC Binary PS Configure the printer to process Macintosh binary PostScript print jobs. Off-The printer Windows print jobs to fail. Auto (default)-The printer processes print jobs from computers using either Windows
  • Lexmark E260D | Service Manual - Page 100
    . None Configuration ID Allow the printer ID to match the label ID after the controller board is replaced. 000101 (default) 000189 Printer alignment Align a new printhead. See "Printhead assembly mechanical adjustment" on None page 3-9 for more information. 3-8 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 101
    ) for wear, the paper path for obstructions, the fuser for proper setting, and the tray paper guides for fit to the media. Paper feed skew Printhead (mechanical) alignment To adjust the printhead: 1. Enter the Diagnostics Menu. See "Diagnostics mode selections" on page 3-8. 2. Press and release
  • Lexmark E260D | Service Manual - Page 102
    below the corresponding lines on the left flap, then adjust the printhead clockwise relative to the printer and recheck. (See the left side of the figure below.) If the grid lines of 7. After obtaining a properly adjusted image on the paper, tighten all three screws. 3-10 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 103
    230 4. Repair information Warning: Read the following before handling electronic parts. Handling ESD-sensitive parts Many electronic products use parts that are known to be sensitive to electrostatic discharge (ESD). To prevent damage to ESD-sensitive parts, follow the instructions below in addition
  • Lexmark E260D | Service Manual - Page 104
    during service. • Unless otherwise stated, reinstall the parts in reverse order of removal. • When reinstalling a part held with several screws, start all screws before final tightening. • Remove the paper tray and print cartridge before proceeding with a removal. 4-2 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 105
    pick tires. Warning: Open the duplex door only far enough to remove the ACM pick tires. If the door is opened too far, then it can become disengaged and interfere with the paper tray. The tray may go in but will not come out, and will render the printer as non-serviceable. 3. After the
  • Lexmark E260D | Service Manual - Page 106
    right and left tire/hub assemblies from the ACM, and replace with the new right and left tire/hub assemblies. • If the left hub is black, then remove the old right and left tires from the ACM hubs, and replace with the new tires. Do not attempt to remove the hubs. A 4-4 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 107
    4513-200, -220, -230 Bezel removal 1. Open the front access door. 2. Flex the top of the bezel, and disconnect the latch (A) from the upper front cover. A 3. Disconnect the latches (B) from the upper front cover. B 4. Remove the bezel. Repair information 4-5
  • Lexmark E260D | Service Manual - Page 108
    its settings from the other card. Critical factory settings are lost when both cards are new and are replaced at the same time. 1. Remove the right side cover. See "Right side cover assembly removal" on page 4-50. 2. Remove the three screws (A) from the USB port. A 4-6 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 109
    4513-200, -220, -230 3. Disconnect all of the cables from the controller board. Note: A drip guard (B) has been added below the controller board. The drip guard may need to be removed to access to the controller board. B 4. Remove the five screws (C) from the controller board. C 5. Lift the
  • Lexmark E260D | Service Manual - Page 110
    sensor 1. Remove the right side cover. See "Right side cover assembly removal" on page 4-50. 2. Disconnect the cable (A) from the controller board. 3. Use a #1 Phillips screwdriver to remove the screw (B) holding the sensor. B A 4. Remove the cover open sensor. 4-8 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 111
    "Left side cover removal" on page 4-23 4. Remove the right side cover. See "Right side cover assembly removal" on page 4-50. 5. Disconnect the operator panel cable (A). 6. Remove the cable through the opening. 7. Remove the three screws (B) from the right side of the printer. Repair information 4-9
  • Lexmark E260D | Service Manual - Page 112
    4513-200, -220, -230 8. Disconnect the fuser link (C). C 9. Remove the three screws (D) from the left side of the printer. 10. Remove the door mounts. 4-10 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 113
    door and rear cover. See "Rear door and rear cover removal" on page 4-46. 3. Place the printer on its top. Note: Be careful to not mar the finish of the printer. 4. Remove the LVPS/HVPS. See "LVPS/HVPS removal" on page 4-26. 5. Remove the three screws (A) from the shield. A 6. Remove the four screws
  • Lexmark E260D | Service Manual - Page 114
    4513-200, -220, -230 7. Lift the duplex slightly, push to the left, and tilt to clear the right side of the printer. 8. Remove the duplex. 4-12 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 115
    will not need to be replaced on the 4513-200 printer. 1. Remove the left side cover. See "Left side cover removal" on page 4-23. 2. Remove the LVPS/HVPS. See "LVPS/HVPS removal" on page 4-26. 3. Remove the duplex. See "Duplex removal" on page 4-11. 4. Remove the main motor gear drive. See "Main
  • Lexmark E260D | Service Manual - Page 116
    4513-200, -220, -230 7. Remove the screw (D) from the gear (E). 8. Remove the plastic bushing (F). 4-14 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 117
    9. Use a screwdriver to pop the retainer clip (G) loose from the gear. 4513-200, -220, -230 10.Remove the gear (H). Repair information 4-15
  • Lexmark E260D | Service Manual - Page 118
    , -220, -230 Fan removal 1. Remove the right side cover. See "Right side cover assembly removal" on page 4-50. 2. Disconnect the cable (A) from the controller board, and remove the two screws (B) holding the fan to the right side frame. B 3. Remove the fan. A B 4-16 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 119
    4513-200, -220, -230 Front access door removal 1. Remove the operator panel. See "Operator panel removal" on page 4-43. 2. Remove the left side cover. See "Left side cover removal" on page 4-23. 3. Close the front access door. 4. While closing the MPF cover, pull up on the MPF by the steel shaft
  • Lexmark E260D | Service Manual - Page 120
    4513-200, -220, -230 6. Disconnect the fuser link (A) from the front access door. A 7. Disconnect the front access door cable (B), and pull it through the opening to clear the side frame. B 4-18 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 121
    8. Disconnect the front access door from its hinges, and remove. 4513-200, -220, -230 Repair information 4-19
  • Lexmark E260D | Service Manual - Page 122
    1. Remove the rear exit guide. See "Rear exit guide assembly with sensor and reversing solenoid removal" on page 4-48. 2. Remove the two screws (A). 3. Partially pull the fuser forward for better access. 4. Push in on the cable connector cover (B), and remove. 4-20 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 123
    5. Disconnect the AC cable (C). 4513-200, -220, -230 C B 6. Disconnect the thermistor cable (D). D Repair information 4-21
  • Lexmark E260D | Service Manual - Page 124
    4513-200, -220, -230 7. Disconnect the exit sensor cable (E) from the controller board. E 8. Remove the fuser. Note: • Be careful to not damage the gears during the fuser installation. • Be sure to reinstall the AC cable during the fuser installation. 4-22 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 125
    door closed when removing the left side cover. • Make sure that the fuser cables are out of the way when removing the left side cover. 1. Remove the paper tray. 2. Remove the screw (A) from the rear left side of the printer. A 3. Remove the screw (B) and press the two latches (C) on the bottom of
  • Lexmark E260D | Service Manual - Page 126
    4513-200, -220, -230 4. Rotate the cover out, and lift to remove the left side cover. Note: There are two tabs on the top of the left side cover. Do not swing the left side cover open too far, or the tabs will be damaged. 4-24 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 127
    Lower front cover removal 1. Open the lower front cover. 2. Disconnect the manual feed plate notch (A) from the lower front cover. 4513-200, -220, -230 A 3. Disconnect the lower front cover notches (B) from the front of the printer. 4. Remove the lower front cover. Repair information 4-25
  • Lexmark E260D | Service Manual - Page 128
    See "Left side cover removal" on page 4-23. 3. Place the printer on its top with the rear facing you. Note: Be careful to not mar the finish of the printer. 4. Remove the two screws (A) from the right rear foot assembly. A 5. Disconnect the fuser power cable (B). B 4-26 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 129
    4513-200, -220, -230 6. Remove the two screws (C) from the right rear foot assembly, and the four screws (D) from the LVPS/ HVPS shield. D C 7. Lift the LVPS/HVPS, and disconnect the three cables (E). E Repair information 4-27
  • Lexmark E260D | Service Manual - Page 130
    4513-200, -220, -230 Note: Squeeze the clip to remove the cables from their connectors (F). F 8. Disconnect the transfer roll cable (G). G 9. Lift and remove the LVPS/HVPS. 4-28 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 131
    the left side cover. See "Left side cover removal" on page 4-23. 2. Open the front access door, and disconnect the fuser link (A). 4513-200, -220, -230 A 3. Place the printer on its right side. Note: Be careful to not mar the finish of the printer. 4. Remove the four screws (B) from the main motor
  • Lexmark E260D | Service Manual - Page 132
    4513-200, -220, -230 5. Lift the gear drive, and disconnect the main motor gear drive cable (C). 6. Remove the main motor gear drive. 4-30 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 133
    clutch removal 1. Remove the left side cover. See "Left side cover removal" on page 4-23. 2. Open the front access door, and disconnect the fuser link (A). 4513-200, -220, -230 A 3. Close the front access door, and place the printer on its right side. Note: Be careful to not mar the finish of the
  • Lexmark E260D | Service Manual - Page 134
    4513-200, -220, -230 6. Use a screwdriver to remove the e-clip (C) from the manual feed clutch. C 7. Remove the manual feed clutch (D). D 4-32 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 135
    right side cover. See "Left side cover removal" on page 4-23. 2. Remove the duplex. See "Duplex removal" on page 4-11. 3. Open the front access door, and place the printer on its right side. Note: Be careful to not mar the finish of the printer. 4. Remove the two screws (A). 4513-200, -220, -230
  • Lexmark E260D | Service Manual - Page 136
    drive removal" on page 4-29. 5. Remove the media feed clutch. See "Remove the media ACM ASM feeder." on page 4-36. 6. Use a screwdriver to pop the shaft retainer tab (A) loose from the ACM feed shaft. 7. Use a small pair of pliers to remove the shaft retainer tab. 4-34 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 137
    8. Use a screwdriver to pop the inner shaft lock (B) loose. 4513-200, -220, -230 9. Remove the inner shaft lock (C). Repair information 4-35
  • Lexmark E260D | Service Manual - Page 138
    4513-200, -220, -230 10. Pull out the auto compensator shaft, and remove the spring (D). 11. Remove the auto compensator shaft. 12. Disconnect the spring (E) from the cylinder. E 13. Remove the media ACM ASM feeder. 4-36 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 139
    Media feed clutch with cable removal 1. Remove the main motor gear drive. See "Main motor gear drive removal" on page 4-29. 2. Remove the duplex. See "Duplex removal" on page 4-11. 3. Disconnect the media feed clutch cable (A) from the controller board. 4. Unroute the cable from the bottom of the
  • Lexmark E260D | Service Manual - Page 140
    4513-200, -220, -230 5. Remove the e-clip (B). 6. Remove the media feed clutch with cable (C). 4-38 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 141
    removal 1. Remove the right side cover. See "Right side cover assembly removal" on page 4-50. 2. Place the machine on its top. Note: Be careful to not mar the finish of the printer. 3. Disconnect the sensor cable (A) from J23 (MPFS) on the controller board. A 4. Remove the screw (B). B 5. Free
  • Lexmark E260D | Service Manual - Page 142
    retainers (F) between the sensor and side frame. F Note: If the cable is not properly installed in its retainers, then the loose cable will obstruct the paper path. 4-40 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 143
    4513-200, -220, -230 Warning: Check to make sure the duplex paper jam door is in its proper position. If it is not, then the paper tray will become lodged and the printer will need to be replaced. Repair information 4-41
  • Lexmark E260D | Service Manual - Page 144
    4513-200, -220, -230 Nameplate removal 1. Open the front access door. 2. Remove the three screws (A). A 3. Remove the nameplate. 4-42 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 145
    Operator panel removal 1. Remove the nameplate. See "Nameplate removal" on page 4-42. 2. Remove the bezel. See "Bezel removal" on page 4-5. 3. Remove the four screws (A) from the display plate. 4513-200, -220, -230 A 4. Lift the operator panel cover, and disconnect the operator panel cable (B). B
  • Lexmark E260D | Service Manual - Page 146
    side cover assembly removal" on page 4-50. 2. Remove the duplex. See "Duplex removal" on page 4-11. 3. Remove the two screws (A) from the sensors. A 4. Disconnect the sensor cable (B) from the controller board. B 5. Remove the paper input and duplex sensor assembly. 4-44 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 147
    the printhead. A 4. Remove the three screws (B). Note: Use a pencil to mark the screw locations of the printhead on the metal frame. Align the new printhead relative to the location of the old printhead. See "Adjustment procedures" on page 3-9. B 5. Remove the printhead. Repair information 4-45
  • Lexmark E260D | Service Manual - Page 148
    4513-200, -220, -230 Rear door and rear cover removal 1. Open the rear door. 2. Pull the rear door up at an angle, disconnect the door from the notch (A), and remove. A 3. Remove the two screws (B) from the top of the rear cover. B 4-46 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 149
    4. Tilt the rear cover, and remove. 4513-200, -220, -230 Repair information 4-47
  • Lexmark E260D | Service Manual - Page 150
    " on page 4-52. 2. Remove the rear door and rear cover. See "Rear door and rear cover removal" on page 4-46. 3. Disconnect the narrow media sensor cable and the reversing solenoid cable (A). 4. Remove the six screws (B) from the rear exit guide assembly. B B B 4-48 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 151
    solenoid cable (C) through the opening. 4513-200, -220, -230 6. Remove the narrow media sensor cable (D) through the opening. 7. Remove the rear exit guide assembly. Note: Be careful to not damage the gears during the rear exit guide assembly removal and reinstallation. Repair information 4-49
  • Lexmark E260D | Service Manual - Page 152
    4513-200, -220, -230 Right side cover assembly removal Note: Leave the front cover closed when removing the right side cover assembly. 1. Remove the one screw (A) from behind the paper tray. A 2. Remove the screw (B) from the bottom right side of the printer. B 4-50 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 153
    3. Press the latches (C). 4513-200, -220, -230 C 4. Rotate the right side cover assembly out, and remove. Repair information 4-51
  • Lexmark E260D | Service Manual - Page 154
    side cover assembly removal" on page 4-50. 4. Remove the rear door and rear cover. See "Rear door and rear cover removal" on page 4-46. 5. Remove the two screws (A) from the left side of the printer. 6. Remove the two screws (B) from the right side of the printer. 4-52 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 155
    7. Lift the top cover, and remove. 4513-200, -220, -230 Note: • Be sure to lift the top cover assembly from the front to remove. • During reinstallation, be sure the exit guide and the paper bin align correctly. A mismatch can cause paper jams. Repair information 4-53
  • Lexmark E260D | Service Manual - Page 156
    springs to assure that they are on the posts. The top of the springs must be captured in the bearings of the transfer roll. 4-54 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 157
    Wear strip (tray 1 and 250-sheet tray 2) removal 1. Hold the tray with the bottom up. 2. Use a spring hook to disconnect the strip from the top of the tray. 4513-200, -220, -230 3. Remove the strip from inside the tray. Repair information 4-55
  • Lexmark E260D | Service Manual - Page 158
    end of the strip is fastened tightly. • Be sure that the drafted edge of the strip is installed toward the bottom of the tray. 4-56 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 159
    230 Locations Front view Rear view Front door Manual feeder door Front door release button Operator panel Paper stop Standard output bin System board door Standard 250-sheet tray (Tray 1) Rear door Ethernet port USB port Parallel port Printer power cord socket Locking device Power switch
  • Lexmark E260D | Service Manual - Page 160
    PANEL J4 CART 1 J13 TNR 1 J501 TPS 1 J17 MTR 1 1 J28 TRAY2 1 J27 IN/DPX J26 FED J25 1 MPT J24 MPF1 1 J23 1 MPFS J502 HVPS/LVPS 1 5-2 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 161
    ) Comments Ground 1.7 V dc Cartridge (The front access door must be printer and wait for all flashing lights .) Cooling fan 24 V dc 24 V dc 0 V dc Duplex solenoid 24 V dc 5 V dc Narrow media sensor 5 V dc Ground 5 V dc Thermistor Ground > 0 V dc 5 V dc 5 V dc Fuser
  • Lexmark E260D | Service Manual - Page 162
    5 V dc Value cable unplugged (if different) Comments 5 V dc Manual feed sensor 0 V dc 0 V dc 5 V dc Manual feed solenoid Media feed clutch Input and duplex sensor Tray 2 0 V dc 0V dc 5V dc 5 V dc 24 V dc 24 V dc 0 V dc Toner patch (density) sensor LVPS/HVPS 5-4 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 163
    4513-200, -220, -230 6. Preventive maintenance This chapter describes procedures for printer preventive maintenance. Follow these recommendations to help prevent problems and maintain optimum performance. Safety inspection guide The purpose of this inspection guide is to aid you in identifying
  • Lexmark E260D | Service Manual - Page 164
    4513-200, -220, -230 6-2 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 165
    pictured in the illustration. • PP: (Parts Packet) in the parts description column indicates the part is contained in a parts packet. • Model information used in the parts catalog. Machine type and model Description 4513-200, -220 Lexmark E260, E260d 4513-230 Lexmark E260dn Parts catalog 7-1
  • Lexmark E260D | Service Manual - Page 166
    4513-200, -220, -230 Assembly 1: Covers 13 1 2 12 3 11 10 9 8 7 7-2 Lexmark™ E260, E260d, E260dn 4 5 6
  • Lexmark E260D | Service Manual - Page 167
    Part number 40X5373 40X5377 40X5375 40X5398 40X5399 40X5394 40X5395 40X2855 40X5382 40X5381 40X5379 40X5359 40X5378 40X5374 40X5353 40X5389 40X5393 Units/ mach Units side cover 1 1 LED bezel cover, E260d 1 1 LED bezel cover, E260dn 1 1 LED bezel cover, E260 (non duplex, EMEA only) 4513-200,
  • Lexmark E260D | Service Manual - Page 168
    4513-200, -220, -230 Assembly 2: Electronics 11 10 9 8 1 2 3 4 5 6 7 7-4 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 169
    6 7 7 8 9 10 11 Part number 40X5352 40X5344 40X5345 40X5346 40X5365 40X5360 40X5392 40X5347 40X5348 40X5361 40X5362 40X5366 40X5369 40X5370 40X5386 Units/ mach 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Units/ FRU 1 1 1 1 1 1 1 1 Description LED operator panel assembly, E260/E260d/E260dn Fuser assembly, 115
  • Lexmark E260D | Service Manual - Page 170
    4513-200, -220, -230 Assembly 3: Frame 10 9 3 8 7 See instruction sheet in the FRU. 6 1 2 3 4 5 7 7-6 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 171
    (CBM) Media exit guide assembly (redrive) Front mounts Screws, miscellaneous TP2NCX3X6PF-Ni TP2C-4.0+8PF-Ni M3.0*0.5+6PF-Ni M3.0*0.5+4PF-Ni M3.5*0.6+6P-Ni Complete duplex assembly (E260d/E260dn only) Media (ACM) drive assembly Paper feed, ACM tires Tray 2 paper feed tires Manual feed clutch CBM Main
  • Lexmark E260D | Service Manual - Page 172
    / mach Units/ FRU Description 1 Japanese font card assembly 1 Simplified Chinese font card assembly 1 Traditional Chinese font card assembly 1 Korean font card assembly 1 128 MB SDR DIMM 1 Parallel cable, packaged (3 m) 1 USB cable, packaged (2 m) 7-8 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 173
    NS NS NS NS NS NS NS NS NS NS NS NS NS Part number 40X0297 40X0278 40X0288 40X0286 40X0275 40X0274 40X0276 40X0287 40X0279 40X0277 40X0282 40X0270 40X0280 40X0281 40X0296 Units/ mach 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Units/ FRU Description Power cord, 1.8M (straight)-USA, Canada Power cord, 6 foot
  • Lexmark E260D | Service Manual - Page 174
    4513-200, -220, -230 7-10 Lexmark™ E260, E260d, E260dn
  • Lexmark E260D | Service Manual - Page 175
    Development Configuration ID 3-8 Defaults 3-8 Edge to Edge 3-8 Print History 3-8 printout sample 3-3 4513-200, -220, -230 E Edge to Edge 3-8 error messages primary light patterns 2-3 service error codes 2-28, 2-42 user attendance messages 2-3 ESD-sensitive parts 4-1 F fan parts catalog 7-5 service
  • Lexmark E260D | Service Manual - Page 176
    page counter 3-4 Reset PC Counter 3-4 S safety information xiii safety inspection guide 6-1 service checks 2-51 controller card 2-51 cooling fan 2-52 cover interlock switch 2-52 dead machine 2-53 fuser 2-53 LVPS/HVPS 2-54 main motor 2-54 operator panel 2-55 I-2 Lexmark™ E260, E260d, E260dn paper
  • Lexmark E260D | Service Manual - Page 177
    optional and primary 7-3 LSU, E260/E260d/E260dn (printhead 7-5 LED bezel cover, E260dn 7-3 Cooling fan (screws included 7-5 LED bezel cover, E260 (non duplex, EMEA only 7-3 Tray 2 assembly 7-3 550-sheet (Tray 2) assembly 7-3 Screws, miscellaneous 7-7 Front mounts 7-7 Part number index I-3
  • Lexmark E260D | Service Manual - Page 178
    7-7 Paper feed, ACM tires 7-7 Media (ACM) drive assembly 7-7 128 MB SDR DIMM 7-8 Korean font card assembly 7-8 Simplified Chinese font card assembly 7-8 Traditional Chinese font card assembly 7-8 Japanese font card assembly 7-8 Field relocation package assembly 7-7 I-4 Lexmark™ E260, E260d
  • Lexmark E260D | Service Manual - Page 179
    E260d/E260dn 70S 5V Gnd TAT201 CN102 CN203 CN202 1 19 2 20 CN201 3.3V 5V 3.3V Gnd 3.3V 3.3V Gnd 3.3V 3.3V 1.7V Gnd Gnd Gnd Gnd Gnd 5V 5V 5V Toner 5V (1.1V) 5V Gnd 70S MPF Sensor Manual Clutch Solenoid Paper Feed Clutch Paper In Sensor Duplex Sensor Tray 2 Connector Plugged
  • Lexmark E260D | Service Manual - Page 180
    80.0 98.3 38.8 48.3 52.4
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Lexmark™ E260, E260d, E260dn
4513-200
4513-220
4513-230
• Table of contents
• Start diagnostics
• Safety and notices
• Trademarks
• Index
Lexmark and Lexmark with diamond design are
trademarks of Lexmark International, Inc., registered
in the United States and/or other countries.