Lexmark E460 SCS/TNe Emulation User's Guide
Lexmark E460 Manual
 |
View all Lexmark E460 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark E460 manual content summary:
- Lexmark E460 | SCS/TNe Emulation User's Guide - Page 1
User's Guide Getting Started SCS/TNe in a LAN environment IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers print server and host software, your printer or Multifunction Product (MFP) becomes an IBM host workstation printer capable of printing IPDS - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 2
appropriate option card installed, the following printers and Muiltifunction Products (MFPs) are supported: • Lexmark C734, C736 • Lexmark E460dn, E460dw, E462dtn • Lexmark T650, T652 • Lexmark T654 • Lexmark T656dne • Lexmark W850 • Lexmark X463de, X464de Getting Started: Equipment Requirements - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 3
printer must have one of the following LAN connections: • Standard Network for connection to an Ethernet LAN (also called STD Net). • MarkNet internal print server (Ethernet). • Lexmark wireless internal print server. If you need to update your Standard Network or MarkNet firmware, refer to "Support - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 4
If you cannot find answers in this guide about using the SCS/TNe emulation, refer to the web site below. If you need to update your Standard Network, MarkNet internal print server, or SCS/TNe firmware, go to http://support.lexmark.com. You may also contact your point of purchase or your local - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 5
using IDB option strings (see "IDB Basics" on page 248 ff. and "Additional TN5250e Printer Commands Using IDB" on page 260 ff). Using IDB in this way is a highly technical in: "Operations Reference - TN3270E SETUP" on page 85 and "Operations Reference - TN5250E SETUP" on page 155. Important - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 6
specialists need to understand and use IDBs. Setup Options vs. Printer Setup Options Setup Options Changes to the option settings under the ™ jobs. The SCS/TNe Emulation user default settings remain in effect until you save new settings or restore the factory defaults by using one of the SCSxxxx - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 7
job may override the user default settings displayed in the printer operator panel. This guide discusses setting up the SCS/TNe Emulation and changing the SCS/TNe Emulation settings. Printer Setup Options Changes to printer settings under the various printer menus, such as Paper Menu and Settings - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 8
how the control panel works. Printers and MFPs differ, so both operator panels on printers and touch screens on MFPs setups. Descriptions of how to carry out installation setups are found in: "Installation Setup for Mainframe Users" on page 28 ff. and "Installation Setup for AS/400 and iSeries Users - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 9
Printer operator Access the SCS/TNe Emulation options and settings from the operpanel ator panel SCS/TNe MENU. To reach the menu: Accessing the top line in the screen shows the menu or menu group name to which the displayed items belong. Understanding the Operator Panel: Printer operator panel 11 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 10
. User-selected default settings remain in effect until you save new settings or restore the factory defaults . All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "Printer - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 11
the Country Code for TN3270. 1 Navigate to TN3270E SETUP. Press the Select button. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP 2 Navigate to SCS OPTIONS. Press the Select button. TN 3270 SETUP NETWORK SCS OPTIONS TEST OPTIONS Understanding the Operator Panel: Printer operator panel 13 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 12
3 Navigate to MISC SETTINGS. Press the Select button. SCS OPTIONS MISC SETTINGS Cor APO Sett TEST OPTIONS 4 Navigate to the Country Code option. Press the Select button. MISC SETTINGS Format Ctrl Sup Country Code Skip Blank Page Understanding the Operator Panel: Printer operator panel 14 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 13
setting is marked with an asterisk *, and in this example, it just happens to be factory default. If you want to change the setting, for example to Fin/Swe, use the Fin/Swe (alt) 6 While the printer is saving the setting, it will display Submitting Selection. Understanding the Operator Panel - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 14
group, press the Back button and then use the navigation buttons and press Select. 9 When you are finished, exit by pressing the Back button to return to the Ready screen. You may need to press it several times until the screen appears. Understanding the Operator Panel - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 15
for selecting a value, because you select the letters from pre-programmed lists. What is special is that the value you select consists example, if you select MENU > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #1 > SERVER 1 INFO > MSGQ 1 Name, you see the Printer operator panel 17 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 16
the numerical pad. If the setting has more than one field, navigate as shown in "Changing a Text String" on page 17. Understanding the Operator Panel: Printer operator panel 18 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 17
To reach the menu: Accessing the SCS/TNe menu 1 Make sure that the printer is on and the Ready message appears. 2 Touch the key icon (Menus) presented ("Selecting a New Value as a Setting" on page 20), enter a number ("Changing a Numerical Setting" on page 22), or enter a text string ("Changing - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 18
discuss slight differences. User-selected default settings remain in effect until you save new settings or restore the factory defaults. All saved options or to scroll to the desired item. In this example locate and touch TN3270E SETUP. 4 Now you will see a list of menus. Touch or to scroll to - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 19
the desired item. In this example locate and touch Country Code. 7 The Back) and no changes will be saved. 9 While the printer is saving the setting, Submitting Selection will be displayed. Changing Card Menu > SCS/TNe Menu > TN3270e Setup > Network Setup > Server Info. 2 Touch the Keyboard symbol - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 20
> Network Setup > Server Info > Keep Alive Time, you will see the following on screen : Touch to decrease the value or to increase the value. Touch (Submit) to save the desired value. When the setting is saved, the screen will return to the previous menu level. Understanding the Operator Panel - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 21
Some numerical values contain more than one field. For example, Menus > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > IP Address. For these, use the Keyboard as described in "Changing a Text String" on page 21. Understanding the Operator Panel: MFP Touch Screen 23 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 22
Remote Configuration Using a Browser Introduction IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. The Card for IPDS and SCS/TNe includes an http user interface. You can use a browser, such as Microsoft Internet Explorer or Netscape, to remotely - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 23
To access and change SCS/TNe option settings through your browser: 1 Access the printer web page by typing the IP address of its print server as the URL. the Execute button next to the Disconnect Ses item. 6 The browser display returns to SCS/TNe Settings. 7 Check to be sure that all sessions have - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 24
If no jobs are printing, you may need to end and reset the session at the host. 8 Return to SCS/TNe Settings. 9 Select one of the TN3270E or page. The Submit button sends the new values to the printer. These values are saved in the printer and will become active when the next session is started. - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 25
the page, next to the Submit button. If you have entered values in the page without submitting, and decide to start all over again, click Reset Form. The page will then display the values that were current when you opened the particular TN page. Remote Configuration Using A Browser: How to Use - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 26
you obtain the latest version of the MarkNet internal print server firmware as well as the latest SCS/TNe publications and Card for IPDS and SCS/TNe code from the internet sites listed in "Support" on page 4. Mainframe Direct Users Task 1A - Configuring the Host Task 2A - Configuring a Host For - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 27
Mainframe Direct Users SNA Server Users Task 6A - Verifying the Mainframe Connection Task 6B - Verifying the Mainframe/SNA Server Connection Mainframe Installation Setup: Introduction 29 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 28
SCS jobs to a LAN attached printer. "Mainframe Software" on page 279 lists versions which support these protocols. The printer with the SCS/TNe Emulation is defined to the host like a normal LU-1 (SCS) printer. Three sample configurations follow. Sample Configuration number 1: Remote Device - Line - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 29
Sample Configuration number 2: PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1), =MTP3816, DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1A - Configuring the Host 31 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 30
Configuration Number 3: Local Device - Using VTAM LOCAL LU nodes First create a major node in VTAM to define the VTAM LU's (printer or EJ3270; are the printer devices. SC0TCP01 is a terminal device, and is not needed for printer definitions in this node. Mainframe Installation Setup: Task 1A - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 31
of a TN printer definition defined in VPS print software: DEST=VPSIMLU1, LUNAME=IMLU1, *LUNAME=SNA047, QBUFSIZE=23476 *ALOGMODE=VPSLU1, *ALOGMODE=VPSCOL, *SEPINFO=HPL The asterisk (*) denotes fields that are not required, and therefore have been commented out. Mainframe Installation Setup: Task 1A - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 32
with the SCS/TNe Emulation is defined to the host like a normal LU-1 (SCS) printer. Two sample configurations are shown below. Sample Configuration number 1 Remote Device - Line definition In VTAM NCP * LNACC=SDLC SDLC SWLINE GROUP G14SD4 GROUP LNCTL=SDLC,TYPE=NCP,OWNER=PCCU1, NRZI=NO,REPLYTO - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 33
Sample Configuration number 2 - PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033, DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA Server 35 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 34
display LU is mapped to a single printer LU or a display LU group is mapped to a printer LU group. Each group must have the same number of LUs. The example below shows how the VTAM section of the TCP/IP PROFILE data-set can be defined. Mainframe Installation Setup: Task 2A - Configuring a Host For - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 35
.36 ENDIPGROUP PRTMAP PRINTERG SPECIP LUMAP SPECLX SPECIP SPECIFIC PRINTERS; specials ; ; ENDVTAM NOTE: If you have multiple printers defined in printmap, you can add multiple IP addresses to the IPGROUP and map the Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 37 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 36
(PRTMAP PRINTERG SPECIP). NOTE: You may also direct a printer device name to the printer IP address using PRTMAP statement as follows: PRTMAP PRT1 xxx.xxx.xxx.xxx (where PRT1 = printer and xxx = printer IP address) Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 38 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 37
order to be able to configure the LU printer connection on the SNA gateway or router. A number of different vendors provide SNA gateways and routers. connection has been selected. To set up a LU printer connection 1 Choose Insert > 3270 > Application LU (LUA). This opens the - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 38
created in the previous step. Choose Assign To > TN3270 Service on > Name-of-SNAServer to assign the connection to the SNA server. Rightclick the new connection again and choose Properties. 4 Left-click the TN3270 tab. Mark Specific Printer and the IBM- 3287-1 terminal name. 5 Click the |OK - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 39
print server or a Standard Network port on the printer. A. To check the installed print server firmware version 1 From a Ready state touch Menus. 2 Network # Setup Page appears, touch it. This prints a settings page for the internal print server in slot #, where # is a number representing the - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 40
the print server to be used for SCS printing, for example Standard Network. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. Mainframe Installation Setup: Task 3 -Configuring a Print Server 42 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 41
for SCS printing, for example Standard Network. Select Standard Network > Std Network Setup > Network Card > Job Timeout. Scroll down to 0. Touch Submit to setting and corresponds to "disabled". Other settings may cause communication problems. A setting of "0" allows the host or SNA server timeout - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 42
address another way. Enable Auto IP On or Off Default is On. This is the recommended setting WINS Server Address Address of your WINS Server DNS Server Address Address of your DNS Server Mainframe Installation Setup: Task 3 -Configuring a Print Server 44 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 43
153 to see the differences in these settings. A. To select Non-US SCS3270 Defaults Factory defaults are US. To change or restore: 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS3270 Defaults. TEST OPTIONS Option SCS3270 Defaults Default Value Do Not Restore - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 44
to save one of the factory defaults. 3 Exit the menu by pressing touching Home. C. To enable Euro support 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > SCS OPTIONS > MISC SETTINGS > Euro Support. MISC SETTINGS Option Default Value Euro Support (IDB Event 191) No Recommended - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 45
the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect return to the SERVER INFO menu group within which you scroll to the next desired option. When you are finished with all options within SERVER INFO, touch Home to exit. Mainframe Installation Setup - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 46
factory default settings and recommended settings. The option setting values found in the table are described in section "NETWORK SETUP name of the host which the printer will contact to receive SCS jobs. number is defined for the Telnet service. Mainframe Installation Setup: Task 5 - Configuring - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 47
not used if the Keep Alive Type is set to None. 3 Set Print Active to Yes. Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Print Active. Scroll to Yes and touch Submit to save. 4 Exit the menu by touching Home. Mainframe Installation - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 48
Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and touch Submit. Touch Home to exit the menus on page 92. Mainframe users should continue with Task 6A. SNA Server users should continue with Task 6B. Mainframe Installation Setup: Task 5 - Configuring - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 49
a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through Card Menu >SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Connect Status. Through the http (browser) user interface: Connect to the print server by - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 50
Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. 3 From the main frame host give the following TCP/IP display - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 51
a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Connect Status. Through the http (browser) user interface: Connect to the print server by - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 52
IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. Through the http (browser) user interface: Connect to the print server by entering the print - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 53
chapter applies to AS/400 and iSeries users. (Mainframe users refer to "Installation Setup for Mainframe Users" on page 28.) The tasks presented firmware, Standard Network or MarkNet internal print server firmware from the internet sites listed in "Support" on page 4 AS/400 and iSeries users - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 54
to print SCS jobs to a LAN attached printer. Section "AS/400 and iSeries Software" on page 279 lists host software which supports these protocols. To configure the host check and QAUTORMT) CHGSYSVAL SYSVAL(QAUTORMT) VALUE('1') AS/400 and iSeries Installation Setup: Task 1 - Configuring the Host 56 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 55
QAUTOVRT CHGSYSVAL QAUTOVRT ### Where ### is the number of devices. When these values are properly configured, the host will auto configure devices and writers with the information received from the SCS/TNe Emulation. AS/400 and iSeries Installation Setup: Task 1 - Configuring the Host 57 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 56
print server or a Standard Network port on the printer. A. To check the installed print server firmware version 1 From a Ready state touch Menus. If Network # Setup Page appears, touch it. This prints a settings page for the internal print server in slot #, where # is a number representing the slot - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 57
server to be used for SCS printing, for example Standard Network. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 59 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 58
setting and corresponds to "disabled". Other settings may cause communication problems. A setting of "0" allows the host SNA server, or the table below. Select Menus > Network/Ports > Standard Network > Std Network Setup > TCP/IP. You will need to contact your network administrator for several of - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 59
address another way. Enable Auto IP On or Off Default is On. This is the recommended setting WINS Server Address Address of your WINS Server DNS Server Address Address of your DNS Server AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 61 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 60
the job. The SCS/TNe Emulation comes with European (A4 paper size) factory default settings. The following five settings are usually the most specific country 1 Select Menus > Option Card Menu > SCS/TNe MENU >TN5250E SETUP > SCS OPTIONS > MISC SETTINGS > Country Code. Scroll to your preferred country - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 61
page 3 Still within MISC SETTINGS, locate Lines Per Page. Scroll to the desired Number and touch Submit to save it. Legal). Recommended values for users in the USA 4 (Select other settings within MISC SETTINGS) 5 Exit the MISC SETTINGS menu by touching Home. AS/400 and iSeries Installation Setup - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 62
>TN5250E SETUP > SCS OPTIONS > PAPER SETTINGS > Page Length. Scroll to the desired value and touch Submit to save it. Default Value 16848 (for A4) Recommended Value Comments 15840 (for Letter). Recommended values for users in 20160 (for Legal). the USA 7 Still within PAPER SETTINGS, locate Page - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 63
> Option Card Menu > SCS/TNe MENU > TN5250E SETUP > SCS OPTIONS > Euro Support. Default Value No Recommended Value Comments 2 Scroll to Yes. Touch Submit to save the setting. 3 Exit the menu by by touching Home. AS/400 and iSeries Installation Setup: Task 3 - Configuring the SCS Settings 65 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 64
an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See options. 5 Locate and touch each option. Enter or scroll to new values and touch Submit to save your settings. The menu will return to the SERVER - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 65
specify the specific IP address or the name of the host which the printer will contact to receive SCS jobs. The host's IP address In order administrator. Another TCP port number may be defined for the Telnet service. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 66
name if it does not exist. None or own preference Leave this at the factory default if the host is configured to send a keep alive signal. Choose a default value to have printer intervention required conditions reported to the host. AS/400 and iSeries Installation Setup: Task 4 - Configuring - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 67
to print. If the writer ends before sending an SCS job to the printer, the TN5250e emulation will not be able to sense the writer has ended. Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and touch Submit. Touch Home to exit the menus. AS/400 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 68
change the Connect # Status from Print Inactive to another status (there are examples of Connect # Status messages on page 92. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 70 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 69
a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through Menu > SCS/TNe MENU > TN5250 SETUP > CONNECTION # SETUP > Connect # Status. Through the http (browser) user interface: Connect to the print server by - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 70
IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. Through the http (browser) user interface: Connect to the print server by entering the print - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 71
queued to print from the host. The job being printed may not be the job which is canceled. The procedures for cancelling a job differ for printers and MFPs, as shown below. Important! When a job is cancelled, the SCS/TNe Emulation stops processing data received from the host. All job data received - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 72
Job 1 Press the Select button on the operator panel while your job is printing 2 The printer will clear the paper path and display a "Stopping" message. 3 In the next menu, press the Select without canceling the job, press the Back button. Important Configuration Basics: Printer Cancel Job 74 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 73
4 The printer will keep you posted on its progress and automatically return to its normal state, which will be BUSY if it is in the process of printing other jobs. Important Configuration Basics: Printer Cancel Job 75 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 74
1 While any job is printing, the Cancel Job icon will be displayed on the printer panel. Touch the icon. 2 In the "Print" column, select the job you message to indicate that the job is being deleted. 5 The screen will return to the Home display. Important Configuration Basics: MFP Cancel Job 76 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 75
Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch COMMON SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP There are four options in the COMMON SETUP menu structure: • Disconnect Ses • Reset TN Session • SCS Debug Trace - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 76
(browser) user interface: Connect to the print server by entering the print server address as the URL. When the print server display appears, click Reports and choose Device Settings. In the following reference tables, an asterisk (*) indicates the default factory value. Operations - Common Setup - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 77
Ses Do Not Disconn., Disconnect Ses. Reset TN Session Do Not Reset, Reset TN Ses. SCS Debug Trace Disable *, PAR Std. Output, PAR Slot# Output, USB Std. Output, USB Slot# Output Reset ALL Def Do Not Reset, Reset All A description of the COMMON SETUP menu items follows. Operations - Common - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 78
printer is powered Off and On or when a Reset TN Ses. is performed. See the Reset TN Session option below. A Disconnect Ses. should be performed before powering Off the printer TNe sessions. The printer must be powered Off and On or a Reset TN Ses. must - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 79
Reset TN Session IMPORTANT: Powering the printer Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP=> Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. This option - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 80
have a computer running a capture program attached to the selected port to receive the trace data, the printer will remain Ready and may not it should only be enabled when needed by service personnel for troubleshooting and service. NOTE: If the SCS/TNe Emulation is Common Setup: SCS Debug Trace 82 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 81
optional parallel port in slot # for trace data output. # is a number representing the slot in which the optional parallel port card is installed. # is a number representing the slot in which the optional USB card is installed. NOTE: Only the interfaces installed in the printer will be displayed. - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 82
panel. Restore ALL SCS/TNe emulation option settings to factory defaults. All sessions will be disconnected. All TNe sessions will have to be reconfigured. Other printer emulation settings (PCL, PS, IPDS, etc.) are not reset when this option is selected. Operations - Common Setup: Reset ALL Def 84 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 83
used when printing from a Mainframe host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TNE3270E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed under the sub-menus accessed from the - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 84
Tree diagram of the TN3270E SETUP menu structure. Operations - TN3270E SETUP: Introduction 86 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 85
installed features. Setting options to values outside the ranges shown in the operator panel is possible via remote configuration and should be avoided. Operations - TN3270E SETUP: Introduction 87 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 86
An Advanced IDB language command line is shown at the end of menu options which may be set by remote configuration. This shows how to remotely set the menu option to the factory default using the Advanced IDB language (cf. "IDB Basics" on page 248 ff.) Operations - TN3270E SETUP: Introduction 88 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 87
*, Restore Defaults Shows Primary Status Messages and Last Response Messages. Refer to Connect Status (page 92) for a description of each message. Sub-menu. See NETWORK SETUP> SERVER INFO Menu: Options Overview (page 95) and Name / IP Address (page 96). A description of each NETWORK - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 88
Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN3270E SETUP: NETWORK SETUP > Print Active 90 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 89
TN3270 Defaults This Network Setup option restores the TN3270e NETWORK SETUP factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed in the - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 90
Connect Status This Network Setup option displays the connection status with the host. The option cannot be changed by the user. Normally only the primary status is shown. If problems occur, a last response message is appended to the primary status message. The complete status message text may not - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 91
Rsp:No support for that device-type Lst Rsp:Name unknown to server Lst Rsp:The requested device is in use Lst Rsp:Terminal/Printer name been disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 92
was made for a specific terminal or printer which is not in any of the TN server's pools the ASSOCIATE command. The device type is not a printer or the device name is not a terminal. Lst printer. The device name requested is the partner to some terminal. Lst Rsp:Error occured An unknown error - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 93
INFO Menu: Options Overview The SERVER INFO menu is a sub-menu under the NETWORK SETUP menu. The following table lists menu options found under the SERVER INFO menu. NETWORK SETUP > SERVER INFO Option name Values Name / IP Address Use IP Address *, Use Hostname IP Address 0.0.0.0 *, IP - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 94
Name / IP Address This Network Setup > Server Info option specifies the kind of address the SCS/TNe Emulation uses to contact the with the IP Address option. Use the hostname specified with the Hostname option. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Name / IP Address 96 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 95
IP Address This Network Setup > Server Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > IP - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 96
Hostname This Network Setup > Server Info option specifies the name used to identify the host to be contacted by the SCS/TNe string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Hostname 98 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 97
. While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > TN Server Port - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 98
Name IMPORTANT: An LU name must be specified in order for the SCS/TNe Emulation to connect to the host or SNA gateway. This Network Setup > Server Info option specifies the LU name assigned to the SCS/TNe Emulation on the host or SNA gateway. Remember also to check the setting - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 99
Device Type This Network Setup > Server Info option specifies the device type for the LU and is available on the host or SNA server. Request an associated printer which is paired with the terminal LU named in the request. Request a generic printer. The LU name is received from the pool of LU names. - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 100
detecting the selected signal type, try changing to another type. Check with your system administrator to determine the type of signal to select. This Network Setup > Server Info option specifies the type of keep alive signal sent to the host or SNA gateway server. This signal is sent to the host - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 101
Keep Alive Time This Network Setup > Server Info option specifies the time in seconds that expires between each keep alive signal sent set to None. Option Value 45 * [1..32000] Comments The range is 1 to 32000 seconds. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Keep Alive Time 103 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 102
SETUP menu. The following table lists menu options and sub-menus found under the SCS OPTIONS menu. SCS OPTIONS Option name COR/APO Sett (IDB Option 122) MISC SETTINGS PAPER (page 106) and FF Support (IDB Option 5) (page 108). Sub-menu. See SCS Options > PAPER SETTINGS Menu: Options Overview (page - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 103
does not fit on a page in portrait orientation, the orientation is changed to landscape. Option Value No Yes * IDB Value 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:2:EXIT Operations - TN3270E SETUP: SCS OPTIONS > COR/APO Sett (IDB Option 122) 105 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 104
and sub-menus found under the MISC SETTINGS menu. SCS OPTIONS >MISC SETTINGS Option name FF Support (IDB Option 5) Non-Print Char (IDB Option 3) CSC Characters (IDB Options 8 & 9) CPI *, 12 CPI, 15 CPI, 16.7 CPI Operations - TN3270E SETUP: SCS Options > MISC SETTINGS Menu: Options Overview 106 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 105
(IDB Option 168) IBM Trn Code (IDB Option 169 bit 1) Leadin Sequence (IDB Option 169 bit2) Euro Support (IDB Event 191) BOLD PRINT Values 132 *, range: 1 - 255 6 *, range: 1 - 255 MISC SETTINGS menu item follows. Operations - TN3270E SETUP: SCS Options > MISC SETTINGS Menu: Options Overview 107 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 106
FF Support (IDB Option 5) This SCS Options > MISC Settings option defines if a form feed and/or Value Always FF * Always LF LF & FF IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 5:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > FF Support (IDB Option 5) 108 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 107
3) This SCS Options > MISC Settings option defines the replacement character to substitute for an unprintable character found in the - 255 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 3:45:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Non-Print Char (IDB Option 3) - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 108
CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option values are to the right. This is done by writing the number of the first option and separating the values for the to set factory default: &%IDB_EDIT: OPTION 8:38,37:EXIT Operations - TN3270E SETUP: MISC - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 109
defines the delimiter used in the Advanced IDB command language to separate programming commands. The IDB option value is an ASCII character in the (:)] Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IDB Delimiter (IDB - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 110
sent when the printer reports a Paper Out, Paper Jam, goes Off-line etc. Option Value Off * On Value Description No IR signals are sent IR signals are sent IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 21:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Use - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 111
>-M command. Note: Because control codes are suppressed, horizontal/vertical tab and other commands which depend on correct page format will not work correctly. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 113 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 112
>+M command is used, CR, LF, NL and FF codes from the host are suppressed. The auto-NL function is still enabled. NOTE: = &% is factory default. + M [m]: If Option 177 = 0, 1 or 2: After this command the auto-NL function is disabled. All host generated control codes are still sent to - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 113
codes can only be sent to the printer with one of the transparent commands. NOTE: The effect of the +M command is reset per job. - M [m]: . Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 177:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 114
Canadian bilingual Canadian French Danish/Norwegian Danish/Norwegian Alternate English, U.K. English, U.S. See note. Finnish/Swedish Finnish/Swedish Alternate French/Azerty 105 International Italian Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 116 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 115
Spanish speaking Spanish Alternate Swiss German/Swiss French Japanese/English Spanish data/text processing NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to English (UK). See the SCS3270 Defaults option. Advanced IDB language to set - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 116
option enabled, pages containing only a CR, NL, LF or FF are skipped. Option Value Do Not Skip * Skip IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 32:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Skip Blank Page (IDB Option 32) 118 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 117
SCS Options > MISC Settings option defines the number of 100) characters per inch. Option Value 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 10 12 15 16 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CPI (IDB Option 100) 119 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 118
SCS Options > MISC Settings option defines the maximum Option 102) number of characters per line. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:132:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Max Prt Pos (IDB Option 102) 120 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 119
LPI (IDB Option This SCS Options > MISC Settings option defines the number of 105) lines per inch. Option Value 6 * [1..255] IDB Value 6 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPI (IDB Option 105) 121 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 120
Line Spacing (IDB Option 106) This SCS Options > MISC Settings option defines the line spacing. Option Value Single * Double IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 106:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Line Spacing (IDB Option 106) 122 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 121
LPP (IDB Option 107) This SCS Options > MISC Settings option defines the number of lines per page. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 122
> MISC Settings option selects the transpar(IDB Option 167) ency mode. Option Value Intermate * Axis Enable MPI feat IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 167:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Transparency (IDB Option 167) 124 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 123
and their values. Option Value ASCII Value 0 * ASCII Value [1..255] IDB Value 0 1 - 255 Comments Disable the Formatted String Utility. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 168:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Form Strings (IDB Option 168) 125 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 124
EBCDIC to ASCII is performed. All transparent data is printed, even invalid data, ie data in the range 40H - FEH. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IBM Trn Code (IDB Option 169 bit 1) 126 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 125
trans- parent handling. 1 User defined transparent lead in characters are used without the pass through sequence. See the CSC Characters (IDB Options 8 & 9) option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Leadin - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 126
This SCS Options > MISC Settings option controls Euro character (IDB Event 191) print support. Option Value No * Yes Comments Disable Euro Support. Enable Euro Support. The ASCII character 186d (0xBAh) is converted to the Euro ASCII character 213d (0xD5h) in symbol set 13U. Operations - TN3270E - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 127
2) Bold On Multi BS (IDB Opt. 22 bit 3) Values Yes *, No Yes *, No Yes *, No A description of each BOLD PRINT menu option follows. Operations - TN3270E SETUP: MISC SETTINGS > SCS Options> MISC SETTINGS > BOLD PRINT 129 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 128
defines Option 22 bit 1) whether or not bold printing is enabled on a carriage return (CR). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On CR (IDB Option 22 bit 1) 130 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 129
22 bit 2) whether or not bold printing is enabled on a backspace (BS). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On BS (IDB Option 22 bit 2) 131 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 130
option defines whether or not bold printing is enabled on multiple backspaces. Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On Multi BS (IDB Opt. 22 bit 3) 132 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 131
Portrait *, Landscape, COR Portrait *, Landscape, COR Portrait *, Landscape, COR Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 133 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 132
A description of each PAPER SETTINGS menu option follows. Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 134 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 133
. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Left Margin (IDB Option 103) 135 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 134
character width depends on the setting of the CPI (IDB Option 100) option. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:132:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Right Margin (IDB Option 104) 136 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 135
defines line number position of the top margin. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 136
default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 109:64:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Bottom Margin (IDB Option 109) 138 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 137
selected in the printer PAPER MENU Paper Source menu. Paper is fed from Tray 1 Paper is fed from Tray 2 Paper is fed from Tray 3 Paper is fed from Tray 4 Paper is fed from Tray 5 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 113:1:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 138
selects the page orien(IDB Option 123) tation for source input tray 1. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 1 Orient (IDB Option 123) 140 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 139
selects the page orien(IDB Option 124) tation for source input tray 2. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 2 Orient (IDB Option 124) 141 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 140
selects the page orien(IDB Option 125) tation for source input tray 3. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 125:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 3 Orient (IDB Option 125) 142 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 141
selects the page orien(IDB Option 126) tation for source input tray 4. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 4 Orient (IDB Option 126) 143 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 142
selects the page orien(IDB Option 127) tation for source input tray 5. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 5 Orient (IDB Option 127) 144 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 143
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 90:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray1 Paper Size (IDB Option 90) 145 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 144
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 91:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray2 Paper Size (IDB Option 91) 146 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 145
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 92:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray3 Paper Size (IDB Option 92) 147 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 146
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 93:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray4 Paper Size (IDB Option 93) 148 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 147
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 94:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray5 Paper Size (IDB Option 94) 149 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 148
TEST OPTIONS Menu: Options Overview The TEST OPTIONS menu is a sub-menu directly under the TN3270E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS3270 Hex Dump Normal Mode *, Hex Dump-Mode Print - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 149
enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation Dump-Mode Comments Normal printer operation. Print job as hex characters without executing control codes. Operations - TN3270E - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 150
Print 3270 IDB This Test option prints a tabular report of the current IDB settings using option numbers. Print this report when asked by technical support representatives. Option Value Do Not Print * Print Comments Do not print the IDB settings. This performs the same action as if Back had been - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 151
restores the TN3270e SCS OPTIONS setting to their factory default settings. Other printer emulation defaults are unchanged. The restored settings ) Tray1 Paper Size (IDB Option 90) US-Default Non-US-Default English (US) English (UK) 64 66 64 66 Letter A4 Operations - TN3270E SETUP: TEST - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 152
91) Tray3 Paper Size (IDB Option 92) Tray4 Paper Size (IDB Option 93) Tray5 Paper Size (IDB Option 94) FF Support (IDB Option 5) COR/APO Sett (IDB Option 122) US-Default Letter Letter Letter Letter Always FF Yes Non-US-Default A4 A4 A4 A4 Always FF Yes Operations - TN3270E SETUP: TEST OPTIONS - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 153
from an AS/400 or iSeries host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TN5250E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed under the sub-menus accessed from the TN5250E - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 154
Tree diagram of the TN5250E SETUP menu structure. Operations - TN5250E SETUP: Introduction 156 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 155
installed features. Setting options to values outside the ranges shown in the operator panel is possible via remote configuration and should be avoided. Operations - TN5250E SETUP: Introduction 157 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 156
for the Advanced IDB language. These show how to remotely set the menu option to the factory default or how to perform the described action (cf. "IDB Basics" on page 248 ff. - and see "Additional TN5250e Printer Commands Using IDB" on page 260 ff.) Operations - TN5250E SETUP: Introduction 158 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 157
Overview The SCS/TNe Emulation supports four concurrent TN5250E sessions. Each session has its own unique set of network settings. These are located in the CONNECTION#1 - A description of each CONNECTION## menu option follows. Operations - TN5250E SETUP: CONNECTION # Menu: Options Overview 159 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 158
the activation of the SCS/TNe Emulation for TN5250E communication and printing. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 159
TN5250## This Connection# option restores the TN5250E CONNECTION #1, Default #2, #3, or #4 factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 160
with the host. The option cannot be changed by the user. The first part of the line shows the primary status message of the Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #). 2 NPA Mode = Off. Solution: Set to Auto. (Path: Menus > Network/ - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 161
Session Disconnected and Halted All active Telnet sessions have been disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. Session established on system [SYSTEM NAME] A Telnet connection is - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 162
object Lst Rsp:8918:Job canceled Lst Rsp:8920:Object partially damaged Lst Rsp:8921:Communication error Lst Rsp:8922:Negative response received Lst Rsp:8923:Start-up record incorrectly Lst Rsp: operator. Check with system operator. Operations - TN5250E SETUP: CONNECTION # > Connect # Status 164 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 163
* or within the range 0 - 65000 Device # Name [undefined] *, ASCII name with up to 10 characters Keep Alive Type None *, Telnet NOP, Timing Mark Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO Menu: Options Overview 165 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 164
name with up to 10 characters. *LIBL *, ASCII name with up to 10 characters. Normal *, Offline, No Reply No *, Yes A description of each SERVER # INFO menu option follows. Name / This with the Hostname # option. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Name / IPaddress # 166 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 165
the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > IP # Address 167 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 166
. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Hostname # 168 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 167
. While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Server # TN - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 168
auto configured with this name if it does not already exist. Option Value [undefined] * Comments Any ASCII text string up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Device # Name 170 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 169
a Timing Mark keep alive signal. Send a Telnet No Operation as the keep alive signal. Send a Telnet timing mark as the keep alive signal. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Keep Alive Type 171 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 170
option value to a value less than the INACTTIMO value on the host. Option Value 45 * [1..32000] Comments The range is 1 to 32000 seconds. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Keep Alive Time 172 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 171
default if you do not know the message queue name. Option Value QSYSOPR * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > MSGQ # Name 173 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 172
the default if you do not know the library name. Option Value *LIBL * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > MSGQ # Lib 174 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 173
No Reply Comments Use normal IR replies, i.e. send paper jam as paper jam, paper out as paper out etc. Only send IR replies as offline messages without specifying what kind of IR has occurred. Disable the use of IR replies. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > IR # Reply 175 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 174
in the same queue. Option Value No * Yes Comments Do not sense if writer ends. Sense if writer ends, reconnect, and reconfigure automatically. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Auto Sense # END 176 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 175
SCS OPTIONS menu is a sub-menu directly under the TN5250E SETUP menu. One set of TN5250E SCS OPTIONS menu values are saved *, Disabled Download Font (IDB Option 244) Enabled *, Disabled Euro Support (IDB Option 139) No *, Yes Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 177 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 176
OPTIONS Option name CSC CHARACTERS COR/APO SETTINGS MISC SETTINGS PAPER SETTINGS Values Sub-menu. See SCS OPTIONS > CSC (page 208) and Country Code (IDB Option 2) (page 210). Sub-menu. See SCS OPTIONS > PAPER SETTINGS Menu: Options Overview (page 231) and Left Margin COR (IDB Opt. 78 & 79) (page - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 177
be executed if paper tray 2 has been selected. Option Value Disable * Enable IDB Value 0 1 User IDB parameter OFF ON User IDB command: OVLCAL : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: OVLCAL OFF:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 178
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 28:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 180 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 179
proportional font handling. The individual character width values of the printer's native fonts must correspond to the width value which * Use IDB Value 0 1 User IDB parameter OFF ON User IDB command: PRPFNTMOV : Parameter: OFF, ON Operations - TN5250E SETUP: SCS OPTIONS > Prop Font - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 180
User IDB language to set factory default: &%IDB_EDIT: PRPFNTMOV OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 118:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 182 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 181
. The command is used to compensate for the reduced printable area of the printer. The option makes it possible to print 80 characters on a line using 49 Option Value Off * On IDB Value 0 1 User IDB parameter OFF ON Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 183 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 182
User IDB command: COMCPI : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: COMCPI OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 128:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 184 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 183
VERMOV : Parameter: For HORMOV ESC uses escape sequences; SP uses spaces For VERMOV ESC uses escape sequences; LF uses line feeds User IDB language to set factory default: &%IDB_EDIT: HORMOV ESC: VERMOV ESC:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 185 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 184
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 158:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 186 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 185
double spaced, disabling it will in most cases solve the problem. Option Value Enabled * Disabled IDB Value 0 1 User IDB parameter ON OFF User IDB command: CTLCODSUP : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: CTLCODSUP ON:EXIT Advanced IDB language to - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 186
printer's memory at Power On. The additional fonts are listed in the table below. The fonts marked with a + contain the Euro character. Option Value Disabled Enabled * IDB Value 0 1 User IDB parameter Not supported Not supported - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 188 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 187
User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 244:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 189 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 188
Euro Support (IDB Option 139) This SCS Options option controls Euro character printing. If the option is set to Yes, the normal code pages are re-mapped to code pages containing the Euro character. This means that the international currency symbol is replaced with the Euro character in the EBCDIC - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 189
IDB parameter OFF ON User IDB command: EURSUP : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: EURSUP OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 139:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Euro Support (IDB Option 139 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 190
- 126 : * (ASCII character 58 [colon]), any single ASCII character in the decimal range: 33 - 126 A description of each CSC CHARACTERS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > SCS OPTIONS > CSC CHARACTERS Menu: Options 192 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 191
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in Value 38 [ampersand] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 192
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB Option 8) 194 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 193
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in Value 37 [percent] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 194
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 9:37:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB Option 9) 196 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 195
IDB Value 58 [colon] User IDB parameter Not supported User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Delimiter - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 196
.126) Off *, On, Enable APO COR LSI Reduc (IDB Option 127) 70% *, range: 1 - 100 [%] A description of each COR/APO SETTINGS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS Menu: Options Overview 198 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 197
> COR/APO Settings option defines the page orientation for paper tray 1. The option setting is only used when the APO/COR User IDB language to set factory default: &%IDB_EDIT: ORTDRW 1 POR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 121:1:EXITz Operations - TN5250E SETUP - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 198
> COR/APO Settings option defines the page orientation for paper tray 2 and above. The option setting is only used when User IDB language to set factory default: &%IDB_EDIT: ORTDRW 2 POR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:1:EXI Operations - TN5250E SETUP - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 199
(Automatic Page Orientation/Computer Output Reduction) works for paper tray 1. With this option it is possible to disable the page orientation change only can be made manually. It is also possible to select between Landscape SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 1 (IDB Option - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 200
command: CORDRW 1 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 1 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 1 (IDB Option - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 201
Orientation/Computer Output Reduction) works for paper tray 2 and above. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 2 (IDB Option - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 202
command: CORDRW 2 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 2 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 2 (IDB Option - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 203
and print all print jobs fulfilling the requirements in computer output reduction mode. Refer to "Appendix D - COR/APO Logic (TN5250e)" on page 287 Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > PPM Quality Dis (IDB Opt.126) 205 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 204
IDB command: TXTMOD : Parameter: OFF, ON, APO User IDB language to set factory default: &%IDB_EDIT: TXTMOD OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > PPM Quality Dis (IDB Opt.126) 206 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 205
LINSPRED : Parameter: 1 - 100 percent of normal line spacing User IDB language to set factory default: &%IDB_EDIT: LINSPRED 70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:70:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR LSI Reduc (IDB - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 206
, 1653, 2103 10 CPI *, 5 CPI, 12 CPI, 15 CPI, 16.7 CPI 80 *, range: 1 - 254 1 *, range: 1 - 255 1 *, range: 1 - 255 6 LPI *, 3 LPI, 4 LPI, 8 LPI, 9 LPI Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS Menu: Options Overview 208 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 207
) Simplex/Duplex (IDB Option 116) Non-Print Char (IDB Option 3) Values 68 *, range: 1 - 255 1 *, range: 1 - 255 Tray 1 *, Tray 2, Tray 3, Tray 4, Tray 5 Prtr Setting *, Paper Media, Envelope Med Prtr Setting *, Output Bin 1, Output Bin 2, Output Bin 3 Prtr Setting *, Simplex, Duplex, Duplex (Tumble - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 208
In country codes other than International country specific characters replace selected characters. Option Value International * USA/Can Ger 3 4 5 6 7 8 9 10 11 12 User IDB parameter 0 1 2 3 4 5 6 7 8 9 10 11 12 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Country Code (IDB Option - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 209
Value 13 14 15 User IDB parameter 13 14 15 User IDB command: DEFCNTCOD : Parameter: 0 - 15 User IDB language to set factory default: &%IDB_EDIT: DEFCNTCOD 0:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 210
by AS/400 and iSeries computers. If Euro Support has been enabled with the Euro Support (IDB Option 139) option, code pages 37, 280 Jap/Eng 281 Portugal 282 Spain 284 Eng (UK) 285 France 297 IDB Values (Option 240 and 241) User IDB parameter 37 + 0 37 3 + 1 259 17 + 1 273 18 + 1 274 19 + 1 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 211
and 241) User IDB parameter OCR 340 84 + 1 340 Multi 500 * 244 + 1 500 Iceland 871 103 + 3 871 Code pages with Euro support below this line 4 1148 Iceland 1149 125 + 4 1149 User IDB command: DEFCODPAG : Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage ( - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 212
Parameter: 37 - 1149 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFCODPAG 500:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 240:244: OPTION 241:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 214 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 213
from the system. Fonts in shaded rows may be loaded into printer memory. See the Download Font (IDB Option 244) option. Option 12 110 Let.Got. Bld 12 111 Pres. Bold 12 112 Pres. It 12 IDB Value (Option 242 and 243) User IDB parameter 3 + 0 3 11 + 0 11 18 + 0 18 39 + 0 39 40 + 0 40 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 214
Son.Ser. 7 1051 Son.Ser. 10 1053 Son.Ser.Bld 10 IDB Value (Option 242 and 243) User IDB parameter 155 + 0 155 159 + 0 159 160 + 0 160 163 + 0 163 175 + 239 + 2 751 27 + 4 1051 29 + 4 1053 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 and 243) 216 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 215
: DEFFNT : Parameter: 3 - 2103 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFFNT 11:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 242:11: OPTION 243:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 216
parameter 5 10 12 15 16 User IDB command: DEFCPI : Parameter: 5, 10, 12, 15, 16 User IDB language to set factory default: &%IDB_EDIT: DEFCPI 10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > CPI - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 217
* [1..254] IDB Value 80 User IDB parameter 80 User IDB command: DEFMPP : Parameter: 1 - 254 User IDB language to set factory default: &%IDB_EDIT: DEFMPP 80:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:80:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 218
[1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFLFTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLFTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 219
[1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFRGTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFRGTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 220
IDB Value 3 4 6 8 9 User IDB parameter 3 4 6 8 9 User IDB command: DEFLPI : Parameter: 3, 4, 6, 8, 9 User IDB language to set factory default: &%IDB_EDIT: DEFLPI 6:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN5250E SETUP: SCS OPTIONS - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 221
This SCS Options > Misc Settings option defines the number of (IDB Option 107) lines per page. Option Value 68 * [1..255] IDB Value 68 User IDB parameter 68 User IDB command: DEFLPP : Parameter: 0 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLPP 68:EXIT Advanced IDB - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 222
[1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFTOPMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFTOPMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 223
the paper source input tray. This tray in the printer. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. User IDB command: DEFSRCDRW : Parameter: DEF, 1, 2, 3, 4, 5, 6, 7, 8 User IDB language to set factory - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 224
the paper tray. The setting will trigger definitions made by the Select Media (SLTMED) command. Option Value Prtr Setting * Paper Media Envelope Med IDB Value 0 1 2 User IDB parameter DEF PAP ENV User IDB command: DEFFRMSEL : Parameter: DEF, PAP, ENV User IDB language to set factory - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 225
IDB command: DEFDSTDRW : Parameter: DEF, 1, 2, 3 User IDB language to set factory default: &%IDB_EDIT: DEFDSTDRW DEF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 115:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Output Bin (IDB Option 115) 227 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 226
display only on printers with duplex support. Option Value Prtr Setting * Simplex Duplex Duplex (Tumble) IDB Value 0 1 2 3 User IDB parameter DEF SIM DUP TUM User IDB command: DEFSIMDUP : Parameter: DEF, SIM, DUP, TUM User IDB language to set factory default: &%IDB_EDIT: DEFSIMDUP - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 227
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 116:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Simplex/Duplex (IDB Option 116) 229 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 228
>: Parameter: All EBCDIC characters or a printable ASCII hex value User IDB language to set factory default: &%IDB_EDIT: UNPCHR /2D:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 3:45:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Non-Print Char (IDB Option - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 229
& 85) Values 634 *, range: 0 - 2880 0 *, range: 0 - 2880 0 *, range: 0 - 2880 147 *, range: 0 - 2880 16848 *, range: 1 - 65535 11908 *, range: 1 - 65535 A description of each PAPER SETTINGS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS Menu: Options Overview 231 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 230
or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFCOR I 0.44:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 78:122: OPTION 79:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 231
× 1440) - (256 × Value stored in option 79) Round off to nearest whole number. The values stored in option 78 and 79 for a left margin offset of 0.440 inch centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt. 78 & 233 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 232
or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFCOR I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 80:0: OPTION 81:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 233
inch × 1440) - (256 × Value stored in option 81) Round off to nearest whole number. The values stored in option 80 and 81 for a top margin offset of 1 inch centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 & 235 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 234
or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFLAN I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 86:0: OPTION 87:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin Lan (IDB Opt. 86 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 235
1440) - (256 × Value stored in option 87) Round off to nearest whole number. The values stored in option 86 and 87 for a left margin offset in Landscape of by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin Lan (IDB Opt. 86 & 87) 237 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 236
] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFLAN I 0.10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 88:147: OPTION 89:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin Lan (IDB Opt - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 237
) - (256 × Value stored in option 89) Round off to nearest whole number. The values stored in option 88 and 89 for a top margin offset in converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin Lan (IDB Opt. 88 & 89) 239 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 238
* Letter Legal Executive Length in cm 29.70 27.94 35.56 26.67 Length in inch. 11.70 11.00 14.00 10.50 Option value 16848 15840 20160 15120 User IDB command: PAGLNG : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 239
decimals User IDB language to set factory default: &%IDB_EDIT: PAGLNG I 11.70:EXIT Advanced IDB language to set factory default: in option 83) Round off to nearest whole number. The values stored in option 82 and 83 Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. 82 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 240
* Letter Legal Executive Width in cm 21.00 21.59 21.59 18.42 Width in inch. 8.27 8.50 8.50 7.25 Option value 11908 12240 12240 10440 User IDB command: PAGWDT : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 241
decimals User IDB language to set factory default: &%IDB_EDIT: PAGWDT I 8.27:EXIT Advanced IDB language to set factory default: stored in option 85) Round off to nearest whole number. The values stored in option 84 and 85 for - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Width (IDB Opt.84 & - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 242
TEST OPTIONS Menu: Options Overview The TEST OPTIONS menu is a sub-menu directly under the TN5250E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS5250 Hex Dump Normal Mode *, Hex Dump-Mode Print - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 243
enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation Dump-Mode Comments Normal printer operation. Print job as hex characters without executing control codes. Operations - TN5250E - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 244
listing the current IDB settings. Print this report when asked by technical support representatives. Option Value Do Not Print Print Comments Do not print the IDB . Print the IDB settings. User IDB language: &%IDB_PRINT_FULL:EXIT Operations - TN5250E SETUP: TEST OPTIONS > Print 5250 IDB 246 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 245
* Restore Defaults Comments Do not restore any settings. This performs the same action as if Back had been pressed in the operator panel. Restore to factory default TN5250E SCS option menu settings. Operations - TN5250E SETUP: TEST OPTIONS > SCS5250 Defaults 247 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 246
applications. The SCS options are programmed using the IDB language. IDB SCS protocol conversion tables. This chapter reviews how to use IDB commands to change guide, available on the internet site with manual updates listed in "Support" on page 4. The IDB Languages Both TN3270E and TN5250E users - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 247
line sequences on the printer. This is typically done by embedding the unique IDB commands in a normal text document which is printed like any normal job. Alternatively, you can retrieve the SCS options as an IDB Configuration File via FTP, edit the file with a utility program and upload it. Several - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 248
the Control Panel" on page 10 ff. "Operations Reference - TN3270E SETUP" on page 85 and "Operations Reference - TN5250E SETUP" on page 155. The descriptions include the available options and their values. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 260 covers IDB commands - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 249
settings with syntax or range errors are ignored. If the SCS/TNe Emulation prints out the commands, or prints out error messages, it could be because the characters used for programming (& % E : ...etc) have been corrupted. You must reset the SCS OPTIONS to their factory defaults. IDB Basics: IDB - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 250
Syntax The commands used for entering and leaving configuration mode are common to the two languages. Enter configuration mode by sending the command: &%IDB_EDIT: and leave configuration mode, by sending the trailer string: EXIT This causes the changed options to be saved. The new option settings - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 251
Programming examples Advanced IDB (TN3270E + TN5250E) User IDB (TN5250E) Valid &%IDB_EDIT: &%IDB_EDIT: - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 252
IDB Configuration File Management This approach is perhaps the most convenient as the contents of all IDB options and events are viewed and edited on a PC screen. After the editing is done, it is possible to save the settings in a file. The resulting IDB Configuration File can then be downloaded to - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 253
IDB settings file 1 Start a FTP session. ftp 201.1.12.123 (Sample IP address) User name: 2 Enter the "/lti" directory. cd /lti 3 Set the FTP client .idb c:\tn3270e.idb (TN3270E users) get tn5250e.idb c:\tn5250e.idb (TN5250E users) This stores the file on the PC in the root directory c:. - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 254
5 End the FTP session. bye IDB Basics: Retrieving the IDB Configuration File 256 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 255
based and is available on the internet site with manual updates listed in "Support" on page 4. Look for the following files. Protocol File TN3270E P01-xxxx.zip TN5250E P02-xxxx.zip Comments This contains the 3270 IDB configuration file editor program, also known as IDB.exe. This contains the 5250 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 256
be changed. The procedure below uses a Microsoft FTP client. To store the IDB settings file 1 Start a FTP session. ftp 201.1.12.123 (Sample IP address) User name: 2 Enter the "/lti" directory. cd /lti 3 Set the FTP client to binary mode. This is necessary as data is transferred in binary - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 257
4 Store the IDB configuration file. put c:\tn3270e.idb put c:\tn5250e.idb (TN3270E users) (TN5250E users) This stores the file from a PC's root directory. 5 End the FTP session. bye The downloaded IDB settings are active on the next SCS job. IDB Basics: Storing the IDB Configuration File 259 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 258
commands described here provide additional commands for controlling the printer. This chapter presents the syntax for creating these data stream. The commands you may work with fall into three groups: 1 Paper Handling 2 Code Page Handling / Code Page 259 3 Miscellaneous See "IDB Basics" on - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 259
Data String Syntax The input data string () following some printer commands can contain three parts: Text, decimal numbers, and hexadecimal numbers. Text: Text has to be put in quotation marks. "This is a text" Decimal: Decimal numbers are entered normally. Use commas to separate. 12,34 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 260
On Initialize Before working with the additional commands, you need to familiarize yourself with the Power On Initialization. This is used to set up the printer each time it is powered On. With the Power On events, it is possible to set up four strings of 1024 bytes each which are - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 261
> : POWON DEL : Parameter: 1 - 4 Example: POWON 3 "Power initialize 3": POWON DEL 3: Delete command Definition number The rest of this chapter is devoted to a run-through of the commands you can work with. TN5250e Printer Commands Using IDB: Initializing - Power On Initialize 263 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 262
74 - 78 for parameters 4 - 8. The events 74 - 78 require programming before they can be used to select a specific input tray. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. Command: SRCDRW -: SRCDRW DEL - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 263
Paper Handling > Destination Drawer This is triggered by the AS/400 or iSeries command - 61. Command: DSTDRW : DSTDRW DEL : Delete command Parameter: 1 - 3 Drawer number Example: DSTDRW 2 /1B,"&l2G": DSTDRW DEL 1: PCL command string for setting dest.drawer 2 to bin 1 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 264
400 or iSeries command PPM (Page Presentation Media) when printing on paper or envelopes is selected. It can also be triggered by the Select paper media Select envelope media Example: SLTMED PAP "Paper media": SLTMED DEL ENV: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper / - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 265
: SLTPAPFED : SLTPAPFED DEL : Delete command Parameter: CON CUT MAN Select continuous paper feed Select cutsheet feed Select manual feed Example: SLTPAPFED MAN /1B,"&l2H": SLTPAPFED DEL CUT: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper Feed 267 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 266
Paper Handling > Select Simplex/Duplex Printing This is used when simplex or duplex printing is selected. The command can only be used if the printer supports duplex printing. It is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when simplex or duplex printing is selected. - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 267
the symbols and signs are not contained in the normal character set of the printer which means that they cannot be used from AS/400 or iSeries. With this command it is possible to switch to another character set in the printer each time code page 259 is used. This can be used to switch to - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 268
Parameter: BEF AFT Before code page 259 selection After code page 259 selection Example: COD259 BEF "Command": COD259 DEL AFT: TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 270 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 269
when paper tray 2 is selected. The command corresponds to event 55 - 56. Command: OVLDRW : OVLDRW DEL : Delete command Parameter: 1 - 2 Drawer number Example: OVLDRW 1 /1B,"&f3Y",/1B,"&f2X":PCL string for calling macro no. 3 OVLDRW DEL 1: TN5250e Printer Commands - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 270
Formfeed Command: BEFAFTFED : BEFAFTFED DEL : Parameter: BEF AFT Example: BEFAFTFED BEF "Command": BEDAFTFED DEF AFT: Delete command Before formfeed After formfeed TN5250e Printer Commands Using IDB: Miscellaneous > Before / After Formfeed 272 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 271
selection Example: BEFPORLAN POR /1B,"&l0E",/1B,"&a0V": PCL command for setting top margin to 0 and moving print position to line 0 BEFPORLAN DEL LAN: TN5250e Printer Commands Using IDB: Miscellaneous > Before Portrait/Landscape Selection 273 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 272
: SUBTIT DEL : Delete command Parameter: IDB HEX Status printout subtitle Hexdump printout subtitle Example: SUBTIT IDB /0A,/0D,"SCS Printer": SUBTIT HEX "Setup for test 05-18-99": SUBTIT DEL HEX: TN5250e Printer Commands Using IDB: Miscellaneous > IDBdump/Hexdump Subtitle 274 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 273
DEL: Delete command Example: MOVUPRLIN /1B,"&l0E",/1B,"&a0V":PCL command for setting top margin to 0 and moving print position to line 0 MOVUPRLIN DEL: TN5250e Printer Commands Using IDB: Miscellaneous> Move to Uppermost Line 275 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 274
Warranty included with the printer The limited warranty you received with your printer gives warranty terms and conditions. For warranty information, refer to your printer documentation. Warranty: included with the printer 276 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 275
which is installed in the printer optional firmware connector; the Card also provides software and this option, the printer can emulate an IBM 3287/3812 in LU1 mode (3270 SCS) or an IBM 3812-01 (5250 SCS) printer. One TN3270e connection is supported. Up to four TN5250e connections are supported - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 276
Compatibility IBM Printer Emulations • 3270 SCS: IBM 3287/3812 in LU1 mode • 5250 SCS: IBM 3812-01 Compatible Print Servers • Standard Network for connection to an Ethernet LAN. • MarkNet internal print server (Ethernet) Appendix - Specifications, Requirements, Features: Compatibility 278 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 277
Server for VM/ESA V2R4, TCP/IP func- tion level 310 or greater • IBM Communications Server for VTAM V4R4 or greater AS/400 and iSeries Software • Application System AS/400 Operating System OS/400 V4R1R5, or V5R1-R3 or greater. • Application System AS/400 Operating System OS/400 V3R7 with PTFs - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 278
Features List: 3270 SCS Features supported are dependent upon host software for selection and use. • SCS (LU1) data stream • 5 bin paper input • EBCDIC character conversion • Text string conversion • IBM and 3rd party ASCII transparency modes • EBCDIC hex-dump Appendix - Specifications, - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 279
/DCA L2 data streams • 5 bin paper input and duplex • Computer Output Reduction (COR) / Automatic Page Orienta- tion (APO) • IBM font selection using FGID or CPI • IBM ASCII transparency • Multiple code pages and box drawing • Full OfficeVision/400 support • User Configurable SCS Features • EBCDIC - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 280
Appendix B - ASCII Character Table Printable The table shows all ASCII printable characters. Characters Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 20 space 32 38 8 56 50 P 80 68 h 104 21 ! 33 39 9 57 51 Q 81 69 i 105 22 " 34 3A : 58 52 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 281
Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 2D - 45 45 E 69 5D ] 93 75 u 117 2E . 46 46 F 70 5E ^ 94 76 v 118 2F / 47 47 G 71 5F _ 95 77 w 119 30 0 48 48 H 72 60 ' 96 78 x 120 31 1 49 49 I 73 61 a 97 79 y 121 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 282
an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS IDB Dump > Print. Appendix - TN3270e IDB Commands: How to Print an IDB Report 284 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 283
List of Larger numbers indicate higher precedence. Commands Precedence Command Comments 5 HEXDUMP Enter hex-dump mode (small format) 5 HEXDUMP_FULL Enter hex-dump mode (large format) 5 IDB_EDIT - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 284
Precedence Command 2 1 {XY} Comments Double CSC (prints ) Single transparent character Refer to the chapter on Understanding the Control Panel (page 10) if necessary. Appendix - TN3270e IDB Commands: List of Commands 286 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 285
(COR) in the SCS/ TNe Emulation is switched on with the CORDRW command. The focus of this discussion is on how the printer automatic controls operate, as the user does not always have the possibility of defining whether a printout is to be rotated and compressed in the system. It Appendix - COR - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 286
that no STO commands are present in the data stream from the system. The STO commands always take priority over the automatic controls of the printer. Details The following points refer to the flowchart in the end of this appen- dix. 1 The calculation of the page format is based on information - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 287
PAGLNG = A4 and PAGWDT = A4 2 If the page format stated in the FCB is within (or equal to) the page size settings of the PAGLNG and PAGWDT option settings, the page size is "valid". In that case the printout will be in landscape provided the page length is smaller than the width, otherwise it will - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 288
• Other pitch sizes are compressed to the nearest smaller font. 4 Most program applications normally have a set of standard values for page length, characters per line etc. The user might have few or no possibilities off changing, e.g., the number of characters per line, which is normally set to 132 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 289
iSeries manuals for information on this subject. Defining the printer file to make the COR is normally done in connection with IPDS page printers as these printers do not support the APO Option 122)" on page 200 for paper tray 1 and 2, respectively. Appendix - COR/APO Logic (TN5250e): Details 291 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 290
Example: Disable COR and set Portrait as default orientation for drawer 2 only. CORDRW 2 = OFF and ORTDRW 2 = POR Flowchart See next page. Appendix - COR/APO Logic (TN5250e): Flowchart 292 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 291
Page Orientation Logic Flowchart Appendix - COR/APO Logic (TN5250e): Flowchart 293 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 292
an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN5250E SETUP > TEST OPTIONS > Print IDB Dump > Print. Appendix - TN5250e IDB Commands: How to Print an IDB Report 294 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 293
List of Larger numbers indicate higher precedence. Commands Precedence Command 5 IDB_EDIT 5 IDB_PRINT 5 IDB_PRINT_FULL 5 /... 5 + 5 - 5 {XY}.... 2 1 {XY} 5 IDB_STATUS 5 < - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 294
IDs (sent from the system) to the internal fonts used in the printer. The font table has a limit of 50 fonts + 3 fonts used for COR (Computer Output Reduction). The SCS/TNe Emulation will detect free font table positions. When attempts to program more than 50 IBM fonts are made, it will print out - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 295
159 (Boldface), 163 (Essay Bold), 160 (Essay) and 175 (Document) which may be loaded into printer memory at Power On. The font table is prepared for using these fonts. The fonts are loaded with code page PC-850 (12U) and with font ID D10003, D10155, D10159, D10160, D10163 and D10175. The loading of - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 296
The "Font" Programming Command This command corresponds to the advanced IDB language FONT command. Command: PRGFNT : PRGFNT DEL fonts represent the substitution font IDs set by the SETSUBFNT command. Appendix - SCS TN5250eFont Table: The "Font" Programming Command 298 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 297
0-65535 This value indicates the IBM font sent from the system. Note that the IBM font numbers are divided into the groups below. pitch area IBM fonts 10 pitch: 1-65 12 pitch: 281-284 27 pitch: 290 typographic: 751-... Appendix - SCS TN5250eFont Table: The "Font" Programming Command 299 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 298
has a maximum length of 255 characters. It has to be programmed the same way as printer command input data. The parameter is optional. No The spacing determines whether the SCS/TNe Emulation or the printer has to control the spacing when using proportional fonts (Fonts with IBM - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 299
P Selection of "P" causes the printer to handle the character spacing. If "P" is selected in connection with programming of a font in the IBM proportional spaced area (154-200), the SCS/TNe Emulation prepares itself for support for downloaded IBM PS fonts. This ensures correct spacing of downloaded - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 300
to make room for new font definitions: PRGFNT DEL 71 PRGFNT DEL 244 PRGFNT DEL 160 PRGFNT DEL 1803 Appendix - SCS TN5250eFont Table: The "Font" Programming Command 302 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 301
: IBM font area 1 - 65 66 - 153 154 - 200 201 - 210 211 - 239 250 - 257 240 - 249 Font table position 1 3 7 4 5 6 2 Command: SETSUBFNT : NOTE: The font number must be a font number already present in the font table. Appendix - SCS TN5250eFont Table: Set Substituted Font ID 303 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 302
Parameter: 1 - 249 Example: SETSUBFNT 86 NOTE: Font 86 needs to be present in the font table prior to this command. The entire font definition (incl. string before/after etc.) is transferred to font table position 3. For instance, if IBM font 67 was the font previously stated in position 3, this is - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 303
herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time. © Copyright 2009 Lexmark International, Inc. © Copyright 2009 Kodak All rights reserved. Edition Notice: SCS/TNe Emulation User's Guide 305 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 304
or both. Intelligent Printer Data Stream and IPDS are trademarks or registered trademarks of Ricoh Co., Ltd in the United States, other countries, or both. Lexmark and Lexmark with diamond design, trademarks are the property of their respective owners. Trademarks: SCS/TNe Emulation User's Guide 306 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 305
's Guide Getting Started ...1 SCS/TNe in a LAN environment ...1 Documentation Overview ...1 Equipment Requirements and Specifications ...2 Support ...4 Customer Support ...4 Important Configuration Basics ...5 Introduction ...5 What are "IDB Options", "IDB events etc.? ...6 Setup Options vs. Printer - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 306
the Mainframe/SNA Server Connection 51 Installation Setup for AS/400 and iSeries Users 53 Introduction ...53 Task 1 - Configuring Printer Cancel Job ...72 MFP Cancel Job ...74 Operations Reference - Common Setup ...75 Introduction ...75 Menu Options Overview ...77 Disconnect Ses ...78 Reset - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 307
Reset ALL Def ...82 Operations Reference - TN3270E SETUP 83 Introduction ...83 NETWORK SETUP Menu: Options Overview ...87 Print Active ...88 TN3270 Defaults ...89 Connect Status ...90 NETWORK SETUP Options > MISC SETTINGS Menu: Options Overview 104 FF Support (IDB Option 5) ...106 Non-Print Char ( - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 308
Option 169 bit2) ...125 Euro Support (IDB Event 191) ...126 Tray 1 Orient (IDB Option 123) ...138 Tray 2 Orient (IDB Option 124) ...139 Tray 3 Orient (IDB Option 125) ...140 Tray 4 Orient (IDB Option 126) ...141 Tray 5 Orient (IDB Option 127) ...142 Tray1 Paper Size (IDB Option 90) ...143 Tray2 Paper - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 309
Operations Reference - TN5250E SETUP 153 Introduction ...153 CONNECTION # Menu: Options Overview ...157 Print Format Ctrl Sup (IDB Option 177) ...185 Download Font (IDB Option 244) ...186 Euro Support (IDB Option 139) ...188 SCS OPTIONS > CSC CHARACTERS Menu: Options Overview 190 IDB First Char - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 310
(IDB Option 114) ...224 Output Bin (IDB Option 115) ...225 Simplex/Duplex (IDB Option 116) ...226 Non-Print Char (IDB Option 3) ...228 SCS OPTIONS > PAPER SETTINGS Menu: Options Overview 229 Left Margin COR (IDB Opt. 78 & 79) ...230 Top Margin COR (IDB Opt. 80 & 81) ...232 Left Margin Lan (IDB - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 311
TN5250e Printer Commands Using IDB 258 Introduction ...258 Input Data String Syntax ...259 Initializing - Power On Initialize ...260 Paper Handling > Source Drawer ...262 Paper Handling > Destination Drawer ...263 Paper Handling > Select Paper / Envelope Media 264 Paper Handling > Select Paper - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 312
IDB Commands ...292 How to Print an IDB Report ...292 List of Commands ...293 Managing the SCS TN5250e Font Table 294 Introduction ...294 The "Font" Programming Command ...296 Set Substituted Font ID ...301 Edition Notice ...303 : 312 - Lexmark E460 | SCS/TNe Emulation User's Guide - Page 313
SCS/TNe Emulation User's Guide ...303 Trademarks ...304 ...304 Table of Contents ...305 : 313
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
 |
 |
1
Getting Started:
SCS/TNe in a LAN environment
Card for IPDS and SCS/TNe -
SCS/TNe Emulation User’s Guide
Getting Started
SCS/TNe in a
LAN
environment
Thank you for purchasing the Card for IPDS and SCS/TNe.
The card provides high quality IBM host connectivity print output.
With the appropriate print server and host software, your printer or
Multifunction Product (MFP) becomes an IBM host workstation
printer capable of printing IPDS or SCS documents from an iSeries,
AS/400, or mainframe. For a more detailed product description, see
“Specifications, Requirements, Features” on page 277
.
I
MPORTANT
:
Unless otherwise stated, the term
printer in this manual refers to both printers and
MFPs.
SCS data is received in a LAN environment using the Telnet
extended protocol. The Card for IPDS and SCS/TNe adds support
for the TN3270E and the TN5250E protocols. A correctly configured
printer can receive, process, and print SCS print jobs received over
TCP/IP.
Documentation
Overview
This document deals only with setting up and using the
SCS/TNe
emulation
in the Card for IPDS and SCS/TNe. It will help you to
understand, use, and change option settings for receiving SNA