Lexmark MS510 PRESCRIBE Emulation Technical Reference Guide

Lexmark MS510 Manual

Get Lexmark MS510 PDF manuals and user guides View all Lexmark MS510 manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark MS510 manual content summary:

  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 1
    Reference October 2012 www.lexmark.com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. All other trademarks are the property of their respective owners. © 2012 Lexmark International, Inc. All rights
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 2
    Flash memory and hard disk support...3 Memorex printer compatibility mode...4 Overview of limitations...4 Certification test process...5 PRESCRIBE commands 6 Command support for P41G...6 Command explanations...10 BARC: draw BAR Code...10 CASS: CASSette ...11 FRPO: Firmware RePrOgram...12 Fonts...19
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 3
    installation instructions that came with the option, or the printer User's Guide. After installing the option, set up the PRESCRIBE FRPO (Firmware RePrOgram) defaults to match the Kyocera default setup on the applications. Many accounts use the Kyocera factory default settings and may not require
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 4
    includes a custom extension to support an alternate font number table which is compatible with Memorex system printers. The font number mapping is .......4 EXIT;5 UEL6 1 Universal Exit Language: ESC%-12345X 2 PCL reset command 3 Memorex entry sequence 4 PRESCRIBE commands 5 Memorex exit sequence
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 5
    emulation of IBM Proprinter. A Proprinter default environment setup is supported by the PRESCRIBE emulation option. See the FRPO section for model numbers of the Kyocera printers in use • A description of the problem and a hard copy output from a Kyocera printer Note: Customers must recertify new
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 6
    BLocK BOX draw BOX CALL CALL macro CASS1 select CASSette or manual mode CIR draw CIRcle CLPR2 CLIP Rectangular area CLSP2 CLoSe diagnostic command) 4 Custom command extension, not part of standard PRESCRIBE language Supported Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 7
    change current FONT FPAT generate Fill PATtern FRPO1 Firmware RePrOgram FRPO INIT FRPO INITialize FSET2 change current or diagnostic command) 4 Custom command extension, not part of standard PRESCRIBE language 7 Supported Yes Yes Yes Yes Yes No Yes Yes Yes Yes No Yes Yes Yes Yes Yes
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 8
    Position !R! PRESCRIBE start sequence RDMP3 Received-data DuMP RES RESet RPF Return to Previous Font RPG2 Return to Previous or diagnostic command) 4 Custom command extension, not part of standard PRESCRIBE language 8 Supported Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 9
    SFNT2 Select current FoNT by typeface SIMG1, 2 Set IMaGe model SLJN2 Set Line JoiN SLM Set Left Margin SLPI UNIT set UNIT of measure XPAT generate eXpanded fill PATtern WRED2, 3 WRite EnD (O&1, 4 enter Memorex Printer Compatibility Mode 1 Partial support or extended support
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 10
    UPC E with five-digit supplement EAN-8 EAN-13 DUN-14 (Distribution Unit Number, EAN) DUN-16 (Distribution Unit Number, EAN) MSI with no check digit MSI with single mod-10 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Supported Yes No No No No No No No Yes No No Yes Yes No No No No No
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 11
    31 32 33 34 35 36 37 38 39 40 41 42 43 44 49 Supported No No No No Yes Yes Yes No No No No No No No Yes No Yes Yes No No Yes CASS: CASSette The CASS command has been extended to support the optional paper sources. The CASS command is mapped as follows: CASS 0; CASS 1; CASS 2; CASS
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 12
    PRESCRIBE commands 12 FRPO: Firmware RePrOgram Kyocera printers support a large set of permanent defaults which can be set using the FRPO command. The PRESCRIBE emulation option supports a subset of the more significant settings. The FRPO INIT command is supported and only affects the settings in
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 13
    Font selection Font 1 for PCL emulation. Font 8 for Proprinter and Line Printer emulations. Sets the default font to the specified font number. Sets the . The L parameters are always acknowledged in Proprinter and Line Printer emulations. Parameters L1-L4 are always acknowledged in PCL emulation.
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 14
    Lexmark printers. • The unprintable areas (no-print regions) for most Lexmark laser printers • The FRPO INIT command does not reset the L parameters. • The L2 laser printers. Although the PRESCRIBE emulation option supports only one base emulation, support for IBM Proprinter (P1=1) and Line Printer
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 15
    limit settings are always acknowledged when the base emulation is Proprinter or Line Printer. U0-U1: Line spacing This sets the number of lines printed per the printer control panel setting for symbol set. If a specific symbol set other than the default is required, then U6 should be set
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 16
    is resident. Currently, there are bitmap versions for font 9 and font 28. Setting LC to 1 forces the printer to print font 9 and font 28 using the bitmap version. The default setting of 0 forces font 9 and as follows: FRPO LE parameter 0 1 2 3 Paper source No source Tray 1 Manual Manual env
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 17
    source. The offset is ignored if LE is set to 0. The offsets are designated in units of 1/300 of an inch. Negative values are allowed. For example, to set up an font instead. SEM: Set Emulation Mode Kyocera printers support a list of printer emulation modes in addition to PRESCRIBE as shown:
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 18
    emulation option only supports PCL 5e, although the PRESCRIBE print environment may be initialized for Proprinter or Line Printer by using the images and patterns. Six different operating modes are defined. The PRESCRIBE emulation option supports modes 3, 4, 5, and 6. Modes 1 and 2 are not supported
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 19
    substituted fonts differ slightly in character style and size. • Customer certification testing is required to determine if font substitutions are compatible with their applications. Resident bitmap font font list for the PRESCRIBE emulation option may not match those of a Kyocera printer.
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 20
    . For more information, see "C3: Default font" on page 13. • Resident scalable font list for the PRESCRIBE emulation option may not match those of a Kyocera printer.
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 21
    in conjunction with other products, programs, or services, except those expressly designated by the manufacturer, are the user's responsibility. For Lexmark technical support, visit support.lexmark.com. For information on supplies and downloads, visit www.lexmark.com. If you don't have access to
  • Lexmark MS510 | PRESCRIBE Emulation Technical Reference Guide - Page 22
    for P41F 6 commands BARC 10 FRPO 12 support for P41F 6 D devices supported 3 F firmware reprogram 12 flash memory and hard disk support 3 fonts bitmap font simulation 19 FRPO commands 12 I installing PRESCRIBE emulation 3 M Memorex printer compatibility mode 4 N notices 21 O overview of limitations
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
PRESCRIBE Emulation P41g
Technical Reference
October 2012
www.lexmark.com
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
All other trademarks are the property of their respective owners.
© 2012 Lexmark International, Inc.
All rights reserved.
740 West New Circle Road
Lexington, Kentucky 40550