Lexmark MS810 PRESCRIBE Emulation Technical Reference Guide

Lexmark MS810 Manual

Get Lexmark MS810 PDF manuals and user guides View all Lexmark MS810 manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark MS810 manual content summary:

  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 1
    Reference October 2012 www.lexmark.com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. All other trademarks are the property of their respective owners. © 2012 Lexmark International, Inc. All rights
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 2
    Flash memory and hard disk support...3 Memorex printer compatibility mode...4 Overview of limitations...4 Certification test process...5 PRESCRIBE commands 6 Command support for P41G...6 Command explanations...10 BARC: draw BAR Code...10 CASS: CASSette ...11 FRPO: Firmware RePrOgram...12 Fonts...19
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 3
    on installing and uninstalling the PRESCRIBE emulation option, see the installation instructions that came with the option, or the printer User's Guide. After installing the option, set up the PRESCRIBE FRPO (Firmware RePrOgram) defaults to match the Kyocera default setup on the applications
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 4
    compatibility mode The PRESCRIBE emulation option includes a custom extension to support an alternate font number table which is compatible with Memorex system printers. The font number mapping is as follows: Memorex font number Standard PRESCRIBE font number 1 1 2 6 3 10 4 15 5 2 6 17
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 5
    emulation of IBM Proprinter. A Proprinter default environment setup is supported by the PRESCRIBE emulation option. See the FRPO section for model numbers of the Kyocera printers in use • A description of the problem and a hard copy output from a Kyocera printer Note: Customers must recertify new
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 6
    BLocK BOX draw BOX CALL CALL macro CASS1 select CASSette or manual mode CIR draw CIRcle CLPR2 CLIP Rectangular area CLSP2 CLoSe diagnostic command) 4 Custom command extension, not part of standard PRESCRIBE language Supported Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 7
    change current FONT FPAT generate Fill PATtern FRPO1 Firmware RePrOgram FRPO INIT FRPO INITialize FSET2 change current or diagnostic command) 4 Custom command extension, not part of standard PRESCRIBE language 7 Supported Yes Yes Yes Yes Yes No Yes Yes Yes Yes No Yes Yes Yes Yes Yes
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 8
    section for details) 2 PRESCRIBE II option 3 Not applicable (for example, unsupported paper option or diagnostic command) 4 Custom command extension, not part of standard PRESCRIBE language 8 Supported Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 9
    SFNT2 Select current FoNT by typeface SIMG1, 2 Set IMaGe model SLJN2 Set Line JoiN SLM Set Left Margin SLPI UNIT set UNIT of measure XPAT generate eXpanded fill PATtern WRED2, 3 WRite EnD (O&1, 4 enter Memorex Printer Compatibility Mode 1 Partial support or extended support
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 10
    UPC E with five-digit supplement EAN-8 EAN-13 DUN-14 (Distribution Unit Number, EAN) DUN-16 (Distribution Unit Number, EAN) MSI with no check digit MSI with single mod-10 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Supported Yes No No No No No No No Yes No No Yes Yes No No No No No
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 11
    31 32 33 34 35 36 37 38 39 40 41 42 43 44 49 Supported No No No No Yes Yes Yes No No No No No No No Yes No Yes Yes No No Yes CASS: CASSette The CASS command has been extended to support the optional paper sources. The CASS command is mapped as follows: CASS 0; CASS 1; CASS 2; CASS
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 12
    PRESCRIBE commands 12 FRPO: Firmware RePrOgram Kyocera printers support a large set of permanent defaults which can be set using the FRPO command. The PRESCRIBE emulation option supports a subset of the more significant settings. The FRPO INIT command is supported and only affects the settings in
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 13
    Font selection Font 1 for PCL emulation. Font 8 for Proprinter and Line Printer emulations. Sets the default font to the specified font number. Sets the . The L parameters are always acknowledged in Proprinter and Line Printer emulations. Parameters L1-L4 are always acknowledged in PCL emulation.
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 14
    should not have to be recomputed for Lexmark printers. • The unprintable areas (no-print regions) for most Lexmark laser printers are 1/6 inch (or 50/ 300 of laser printers. Although the PRESCRIBE emulation option supports only one base emulation, support for IBM Proprinter (P1=1) and Line Printer
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 15
    limit settings are always acknowledged when the base emulation is Proprinter or Line Printer. U0-U1: Line spacing This sets the number of lines printed per be initialized according to the printer control panel setting for symbol set. If a specific symbol set other than the default is required, then
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 16
    is resident. Currently, there are bitmap versions for font 9 and font 28. Setting LC to 1 forces the printer to print font 9 and font 28 using the bitmap version. The default setting of 0 forces font 9 and as follows: FRPO LE parameter 0 1 2 3 Paper source No source Tray 1 Manual Manual env
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 17
    source. The offset is ignored if LE is set to 0. The offsets are designated in units of 1/300 of an inch. Negative values are allowed. For example, to set up an font instead. SEM: Set Emulation Mode Kyocera printers support a list of printer emulation modes in addition to PRESCRIBE as shown:
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 18
    only supports PCL 5e, although the PRESCRIBE print environment may be initialized for Proprinter or Line Printer by supported. The nonexecutable parameters may affect best-fit font selections, and could result in the PRESCRIBE emulation option selecting a different font than Kyocera. SIMG: Set IMaGe
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 19
    font simulation The following table lists the Kyocera resident bitmap fonts, and the PRESCRIBE emulation best-fit fonts which are used from the standard set of PCL resident scalable fonts. Selection of scalable font list for the PRESCRIBE emulation option may not match those of a Kyocera printer.
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 20
    Fonts 20 Resident bitmap font substitution table Kyocera font name Best‑fit font name Font # Port. Font # Land. Height (points) Pitch (cpi) PrestigeEliteBM7.2-Bold Courier Bold (scalable) scalable font list for the PRESCRIBE emulation option may not match those of a Kyocera printer.
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 21
    THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some services, except those expressly designated by the manufacturer, are the user's responsibility. For Lexmark technical support, visit support.lexmark.com. For information on supplies and downloads, visit www.lexmark
  • Lexmark MS810 | PRESCRIBE Emulation Technical Reference Guide - Page 22
    for P41F 6 commands BARC 10 FRPO 12 support for P41F 6 D devices supported 3 F firmware reprogram 12 flash memory and hard disk support 3 fonts bitmap font simulation 19 FRPO commands 12 I installing PRESCRIBE emulation 3 M Memorex printer compatibility mode 4 N notices 21 O overview of limitations
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
PRESCRIBE Emulation P41g
Technical Reference
October 2012
www.lexmark.com
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
All other trademarks are the property of their respective owners.
© 2012 Lexmark International, Inc.
All rights reserved.
740 West New Circle Road
Lexington, Kentucky 40550