Lexmark Platinum Pro905 User's Guide - Page 157

Network troubleshooting, Network troubleshooting checklist - printer driver

Get Lexmark Platinum Pro905 PDF manuals and user guides View all Lexmark Platinum Pro905 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 157 highlights

Network troubleshooting • "Network troubleshooting checklist" on page 157 • "The Continue button is unavailable" on page 158 • "Cannot print and there is a firewall on the computer" on page 159 • "Communication with printer lost when connected to Virtual Private Network (VPN)" on page 160 Network troubleshooting checklist Before beginning to troubleshoot the wireless printer, verify the following: General Networking Make sure: • The printer, the computer, and the wireless access point are all plugged in and turned on. • The wireless network is working properly. Try accessing other computers on your wireless network. If your network has Internet access, try connecting to the Internet over a wireless connection. • The printer driver is installed on the computer from which you are performing a task. • The correct printer port is selected. • The IP address, gateway, and network mask are correct for your network. Print a network setup page from the printer to check the network settings. • All switches, hubs, and other connecting devices are turned on. Ethernet Networking Make sure: • The Ethernet cable and connectors are not damaged. Check the connectors at both ends for any obvious damage. If possible, use a new cable. Damage to the cable may not be obvious. • The Ethernet cable is firmly plugged in to the printer and to the network hub or wall connection. Wireless Networking Make sure: • The SSID is correct. Print a network setup page from the printer to check the network settings. • Your WEP key or WPA passphrase is correct (if your network is secure). Log in to the wireless access point (wireless router) and check the security settings. If you are not sure if your security information is correct, run the wireless setup again. • The printer and the computer are within the range of the wireless network. For most networks, the printer and the computer should be within 100 feet (30 meters) of the wireless access point (wireless router). • The Wi-Fi indicator light is lit and is solid green. • The computer and printer are both connected to the same wireless network. Troubleshooting 157

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
Network troubleshooting
•
“Network troubleshooting checklist” on page 157
•
“The Continue button is unavailable” on page 158
•
“Cannot print and there is a firewall on the computer” on page 159
•
“Communication with printer lost when connected to Virtual Private Network (VPN)” on page 160
Network troubleshooting checklist
Before beginning to troubleshoot the wireless printer, verify the following:
General Networking
Make sure:
•
The printer, the computer, and the wireless access point are all plugged in and turned on.
•
The wireless network is working properly.
Try accessing other computers on your wireless network. If your network has Internet access, try connecting to
the Internet over a wireless connection.
•
The printer driver is installed on the computer from which you are performing a task.
•
The correct printer port is selected.
•
The IP address, gateway, and network mask are correct for your network.
Print a network setup page from the printer to check the network settings.
•
All switches, hubs, and other connecting devices are turned on.
Ethernet Networking
Make sure:
•
The Ethernet cable and connectors are not damaged.
Check the connectors at both ends for any obvious damage. If possible, use a new cable. Damage to the cable
may not be obvious.
•
The Ethernet cable is firmly plugged in to the printer and to the network hub or wall connection.
Wireless Networking
Make sure:
•
The SSID is correct.
Print a network setup page from the printer to check the network settings.
•
Your WEP key or WPA passphrase is correct (if your network is secure).
Log in to the wireless access point (wireless router) and check the security settings.
If you are not sure if your security information is correct, run the wireless setup again.
•
The printer and the computer are within the range of the wireless network.
For most networks, the printer and the computer should be within 100 feet (30 meters) of the wireless access
point (wireless router).
•
The Wi-Fi indicator light is lit and is solid green.
•
The computer and printer are both connected to the same wireless network.
Troubleshooting
157