Lexmark W850 SCS/TNe Emulation User's Guide
Lexmark W850 Manual
 |
View all Lexmark W850 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark W850 manual content summary:
- Lexmark W850 | SCS/TNe Emulation User's Guide - Page 1
Card for IPDS and SCS/TNe - SCS/TNe Emulation User's Guide Getting Started SCS/TNe in a LAN environment IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. Thank you for purchasing the Card for IPDS and SCS/TNe. The card provides high quality IBM - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 2
and Specifications Supported Products With the appropriate option card installed, the following printers and Muiltifunction Products (MFPs) are supported: • Lexmark C734, C736 • Lexmark E460dn, E460dw, E462dtn • Lexmark T650, T652 • Lexmark T654 • Lexmark T656dne • Lexmark W850 • Lexmark X463de - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 3
for connection to an Ethernet LAN (also called STD Net). • MarkNet internal print server (Ethernet). • Lexmark wireless internal print server. If you need to update your Standard Network or MarkNet firmware, refer to "Support" on page 4. For further information on requirements and specifications - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 4
If you cannot find answers in this guide about using the SCS/TNe emulation, refer to the web site below. If you need to update your Standard Network, MarkNet internal print server, or SCS/TNe firmware, go to http://support.lexmark.com. You may also contact your point of purchase or your local - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 5
, the term printer refers to printers and MFPs, and the term control panel refers to operator panels and touch screens on these types of products. SCS/TNe MENU options settings can be changed and saved in three ways: • Use the control panel ("Understanding the Control Panel" on page 10 - which also - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 6
IDB values, IDB User Parameters, IDB Language, etc. Refer to "IDB Basics" on page 248 for additional information. Note that in most cases, only technical specialists need to understand and use IDBs. Setup Options vs. Printer Setup Options Setup Options Changes to the option settings under the SCS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 7
may override the user default settings displayed in the printer operator panel. This guide discusses setting up the SCS/TNe Emulation and changing the SCS/TNe Emulation settings. Printer Setup Options Changes to printer settings under the various printer menus, such as Paper Menu and Settings, will - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 8
out installation setups are found in: "Installation Setup for Mainframe Users" on page 28 ff. and "Installation Setup for AS/400 and iSeries Users" on page 55 ff. Detailed, specialized listings and descriptions of option settings are found in: "Operations Reference - TN3270E SETUP" on page 85 and - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 9
Printer operator Access the SCS/TNe Emulation options and settings from the operpanel ator panel SCS/TNe MENU. To reach the menu: Accessing the SCS/TNe menu 1 From a Ready status, press the MENU button . on the operator panel. This opens the menu index in the operator panel's screen. 2 Use the - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 10
the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "Printer operator panel" on page 11. 2 Use the navigation buttons or desired menu and press Select. to scroll - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 11
change the Country Code for TN3270. 1 Navigate to TN3270E SETUP. Press the Select button. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP 2 Navigate to SCS OPTIONS. Press the Select button. TN 3270 SETUP NETWORK SCS OPTIONS TEST OPTIONS Understanding the Operator Panel: Printer operator panel - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 12
3 Navigate to MISC SETTINGS. Press the Select button. SCS OPTIONS MISC SETTINGS Cor APO Sett TEST OPTIONS 4 Navigate to the Country Code option. Press the Select button. MISC SETTINGS Format Ctrl Sup Country Code Skip Blank Page Understanding the Operator Panel: Printer operator panel 14 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 13
navigation buttons to move down through the list. When the on-screen checkmark is next to the desired setting. press the Select button Country Code English (US) Fin/Swe Fin/Swe (alt) 6 While the printer is saving the setting, it will display Submitting Selection. Understanding the Operator Panel - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 14
7 When the setting is saved, the display will revert to the previous menu level. MISC SETTINGS Format Ctrl Sup Country Code Skip Blank Page If you want to check the value of a setting, press the Select button again. You will see an asterisk * beside Fin/Swe to show it - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 15
that the value you select consists of several fields. For example, if you select MENU > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #1 > SERVER 1 INFO > MSGQ 1 Name, you see the following display: all the characters. Understanding the Operator Panel: Printer operator panel 17 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 16
a menu item that has a numerical value, you can usually choose between scrolling just as you would to select any value, or using the numerical pad. If the setting has more than one field, navigate as shown in "Changing a Text String" on page 17. Understanding the Operator Panel: Printer operator - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 17
MFP Touch Access the SCS/TNe Emulation options and settings from the operScreen ator panel SCS/TNe MENU. To reach the menu: Accessing the SCS/TNe menu 1 Make sure that the printer is on and the Ready message appears. 2 Touch the key icon (Menus) on the operator panel 3 Touch or to scroll - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 18
User-selected default settings remain in effect until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "MFP Touch Screen" on page - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 19
list of options.Touch or to scroll to the desired item. In this example locate and touch Country Code. 7 printer is saving the setting, Submitting Selection will be displayed. Changing a Text String Here is an example. 1 Select Menus > Option Card Menu > SCS/TNe Menu > TN3270e Setup > Network Setup - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 20
you have completed the name. The screen returns to the previous menu level. 6 Touch (Submit) to save changes. Changing a Numerical Setting Example: If you select Menus > Option Card Menu > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > Keep Alive Time, you will see the following on - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 21
Some numerical values contain more than one field. For example, Menus > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > IP Address. For these, use the Keyboard as described in "Changing a Text String" on page 21. Understanding the Operator Panel: MFP Touch Screen 23 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 22
and SCS/TNe includes an http user interface. You can use a browser, such as Microsoft Internet Explorer or Netscape, to remotely configure most SCS/TNe settings. The only requirement is that the printers are attached to a LAN using a Standard Network port or MarkNet internal print server. Remote - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 23
the Browser Interface To access and change SCS/TNe option settings through your browser: 1 Access the printer web page by typing the IP address of its print server all sessions have been disconnected. Click on each TNxxxx Connection Status menu item to check the status of each session. Remote Configuration - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 24
10 All option values which may be changed remotely will be displayed. Change option settings as desired. 11 Select the Submit button at the bottom of the page. The Submit button sends the new values to the printer Common menu. 15 Reset all sessions by clicking on the Execute button next to the Reset - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 25
TNxxxx Connection Status menu item to check the status of each session. If all configured sessions have not been established within 90 seconds, you may need to end and reset the sessions at the host and repeat steps 14 - 16. On each TN menu, you will see a Reset Form button at the bottom of the page - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 26
you obtain the latest version of the MarkNet internal print server firmware as well as the latest SCS/TNe publications and Card for IPDS and SCS/TNe code from the internet sites listed in "Support" on page 4. Mainframe Direct Users Task 1A - Configuring the Host Task 2A - Configuring a Host For - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 27
Mainframe Direct Users SNA Server Users Task 6A - Verifying the Mainframe Connection Task 6B - Verifying the Mainframe/SNA Server Connection Mainframe Installation Setup: Introduction 29 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 28
SCS jobs to a LAN attached printer. "Mainframe Software" on page 279 lists versions which support these protocols. The printer with the SCS/TNe Emulation is defined to the host like a normal LU-1 (SCS) printer. Three sample configurations follow. Sample Configuration number 1: Remote Device - Line - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 29
Sample Configuration number 2: PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1), =MTP3816, DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1A - Configuring the Host 31 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 30
Configuration Number 3: Local Device - Using VTAM LOCAL LU nodes First create a major node in VTAM to define the VTAM LU's (printer or EJ3270; are the printer devices. SC0TCP01 is a terminal device, and is not needed for printer definitions in this node. Mainframe Installation Setup: Task 1A - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 31
to the host print software being used. The following is an example of a TN printer definition defined in VPS print software: DEST=VPSIMLU1, LUNAME=IMLU1, *LUNAME=SNA047, QBUFSIZE= not required, and therefore have been commented out. Mainframe Installation Setup: Task 1A - Configuring the Host 33 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 32
with the SCS/TNe Emulation is defined to the host like a normal LU-1 (SCS) printer. Two sample configurations are shown below. Sample Configuration number 1 Remote Device - Line definition In VTAM NCP * LNACC=SDLC SDLC SWLINE GROUP G14SD4 GROUP LNCTL=SDLC,TYPE=NCP,OWNER=PCCU1, NRZI=NO,REPLYTO - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 33
Sample Configuration number 2 - PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033, DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA Server 35 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 34
display LU is mapped to a single printer LU or a display LU group is mapped to a printer LU group. Each group must have the same number of LUs. The example below shows how the VTAM section of the TCP/IP PROFILE data-set can be defined. Mainframe Installation Setup: Task 2A - Configuring a Host For - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 35
.36 ENDIPGROUP PRTMAP PRINTERG SPECIP LUMAP SPECLX SPECIP SPECIFIC PRINTERS; specials ; ; ENDVTAM NOTE: If you have multiple printers defined in printmap, you can add multiple IP addresses to the IPGROUP and map the Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 37 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 36
(PRTMAP PRINTERG SPECIP). NOTE: You may also direct a printer device name to the printer IP address using PRTMAP statement as follows: PRTMAP PRT1 xxx.xxx.xxx.xxx (where PRT1 = printer and xxx = printer IP address) Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 38 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 37
be able to configure the LU printer connection on the SNA gateway or router. A number of different vendors provide SNA connection has been selected. To set up a LU printer connection 1 Choose Insert > 3270 > Application LU (LUA). This opens the 3270 LU Properties box. Mainframe Installation Setup - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 38
created in the previous step. Choose Assign To > TN3270 Service on > Name-of-SNAServer to assign the connection to the SNA server. Rightclick the new connection again and choose Properties. 4 Left-click the TN3270 tab. Mark Specific Printer and the IBM- 3287-1 terminal name. 5 Click the |OK - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 39
port on the printer. A. To check the installed print server firmware version 1 From a Ready state touch Menus. 2 Touch Reports. 3 Scroll until one or more of the following appears. If none of these appear, then you do not have a Standard Network or internal print server installed. a If Network Setup - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 40
Select Menus > Network/Ports. Select the print server to be used for SCS printing, for example Standard Network. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. Mainframe Installation Setup: Task - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 41
another protocol, interface, server, or host can be started. 3 Set the TCP/IP option values shown in the table below. Select Menus > Network/Ports > Standard Network > Std Network Setup > TCP/IP. You will need to contact your network administrator for several of the values. Mainframe Installation - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 42
Option Value Description Address Address available from your network administrator. Netmask Netmask for your network. Contact your network administrator. Gateway Address of the IP gateway. Contact your network DNS Server Mainframe Installation Setup: Task 3 -Configuring a Print Server 44 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 43
SCS3270 Defaults, page 153 to see the differences in these settings. A. To select Non-US SCS3270 Defaults Factory defaults are US. To change or restore: 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS3270 Defaults. TEST OPTIONS Option SCS3270 Defaults Default - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 44
Value Country Code (IDB Option 2) English (US) Recommended Value Comments Your preferred country 2 Scroll to the desired value. Touch SelectSubmit to save one of the factory defaults. 3 Exit the menu by pressing touching Home. C. To enable Euro support 1 Select Menus > Option Card Menu > SCS/TNe - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 45
Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. SCS jobs are printed from a LAN connected Mainframe using TCP/ IP and the telnet extended (TN3270e - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 46
Menu: Options Overview" on page 95. SERVER INFO Option Name / IP Address IP Address Hostname TN Server Port Default Value Recommended Value Comments Use IP Address Check with your system administrator whether you need to specify the specific IP address or the name of the host which the printer - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 47
10 characters) This name must be defined on the host or SNA Server. Please note! Some hosts and servers only recognize uppercase LU Names. Specific Print Active to Yes. Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Print Active. Scroll to Yes and touch Submit to save. - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 48
to communicate and change the Connect Status from Print Inactive to another status (there are examples of Connect Status messages on page 92. Mainframe users should continue with Task 6A. SNA Server users should continue with Task 6B. Mainframe Installation Setup: Task 5 - Configuring the SCS/TNe - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 49
actions: 1 Check the TN3270E Connection Status (see page 92) From the Operator Panel: Display the TN3270E Connect Status by selecting Menus > Option Card Menu >SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Connect Status. Through the http (browser) user interface: Connect to the print server by - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 50
manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. 3 From the main frame host give the following TCP/IP display command: D TCPIP,TCPIPNAME,TELNET,CONNECTION,PORT = ALL to see all - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 51
actions: 1 Check the TN3270E Connection Status (see page 92) From the Operator Panel: Display the TN3270E Connect Status by selecting Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Connect Status. Through the http (browser) user interface: Connect to the print server by - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 52
Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. Through the http (browser) user interface: Connect to the print server by entering the print server - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 53
is recommended that you obtain the latest version of the SCS/TNe firmware, Standard Network or MarkNet internal print server firmware from the internet sites listed in "Support" on page 4 AS/400 and iSeries users Task 1 - Configuring the Host Task 2 - Configuring a Print Server Task 3 - Configuring - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 54
to print SCS jobs to a LAN attached printer. Section "AS/400 and iSeries Software" on page 279 lists host software which supports these protocols. To configure the host check and QAUTORMT) CHGSYSVAL SYSVAL(QAUTORMT) VALUE('1') AS/400 and iSeries Installation Setup: Task 1 - Configuring the Host 56 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 55
QAUTOVRT CHGSYSVAL QAUTOVRT ### Where ### is the number of devices. When these values are properly configured, the host will auto configure devices and writers with the information received from the SCS/TNe Emulation. AS/400 and iSeries Installation Setup: Task 1 - Configuring the Host 57 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 56
port on the printer. A. To check the installed print server firmware version 1 From a Ready state touch Menus. 2 Touch Reports. 3 Scroll until one or more of the following appears. If none of these appear, then you do not have a Standard Network or internal print server installed. a If Network Setup - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 57
Menus > Network/Ports Select the print server to be used for SCS printing, for example Standard Network. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. AS/400 and iSeries Installation Setup: Task - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 58
protocol, interface, server, or host can be started. 3 Set the TCP/IP option values shown in the table below. Select Menus > Network/Ports > Standard Network > Std Network Setup > TCP/IP. You will need to contact your network administrator for several of the values. You will need to contact your - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 59
Option Value Description Address Address available from your network administrator. Netmask Netmask for your network. Contact your network administrator. Gateway Address of the IP gateway. Contact your network AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 61 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 60
of TN5250e SCS OPTIONS menu values is saved. All four TN5250e connections use the same set of SCS OPTIONS values. A. To select settings for your specific country 1 Select Menus > Option Card Menu > SCS/TNe MENU >TN5250E SETUP > SCS OPTIONS > MISC SETTINGS > Country Code. Scroll to your preferred - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 61
Your preferred code page 3 Still within MISC SETTINGS, locate Lines Per Page. Scroll to the desired Number and touch Submit to save it. Option Lines Per Page (IDB Option 107) Default Value 68 (for A4) Recommended Value Comments 64 (for Letter). 82 (for Legal). Recommended values for users in - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 62
& 85) 6 Select Menus > Option Card Menu > SCS/TNe MENU >TN5250E SETUP > SCS OPTIONS > PAPER SETTINGS > Page Length. Scroll to the desired value and touch Submit to save it. Default Value 16848 (for A4) Recommended Value Comments 15840 (for Letter). Recommended values for users in 20160 (for Legal - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 63
Option Euro Support (IDB Option 139) B. To enable Euro support 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > SCS OPTIONS > Euro Support. Default Value No Recommended Value Comments 2 Scroll to Yes. Touch Submit to save the setting. 3 Exit the menu by by touching Home. AS/ - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 64
IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. SCS jobs are printed from a LAN connected AS/400 or iSeries host using TCP/IP and the telnet - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 65
values found in the table are described in section "CONNECTION # > SERVER # INFO Menu: Options Overview" on page 165. Option Default Value Name / IPaddress # Use IP# Address IP # Address 0.0.0.0 Hostname # [undefined] Server # TN Port 23 Recommended Value Comments Check with your system - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 66
the message queue the MSGQ # Name option. This library must already exist (up to 10 characters) on the host It will not be auto configured. Contact your system administrator if you do not know the library name. Normal Leave this option at its default value to have printer intervention required - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 67
Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION # > Print # Active. Scroll to Yes and touch Submit to save. 7 Exit the menu by touching Home. 8 To activate the new settings, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 68
, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the Connect # Status from Print Inactive to another status (there are examples of Connect # Status messages on page 92. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 70 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 69
: 1 Check the TN5250E Connection Status (see page 162). From the Operator Panel: Display the TN5250E Connect Status by selecting Menus > Option Card Menu > SCS/TNe MENU > TN5250 SETUP > CONNECTION # SETUP > Connect # Status. Through the http (browser) user interface: Connect to the print server by - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 70
Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. Through the http (browser) user interface: Connect to the print server by entering the print server - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 71
SCS/TNe Cancel About Cancel Job SCS jobs may be canceled at the printer or MFP. Cancel Job only displays when the printer or MFP is processing a print job. Selecting a specific job to cancel is difficult when several small jobs are queued to print from the host. The job being printed may not be - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 72
Cancel Job 1 Press the Select button on the operator panel while your job is printing 2 The printer will clear the paper path and display a "Stopping" message. 3 In the next menu, press the Select button when the on- screen checkmark is beside the job you want to cancel. There may be only one - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 73
4 The printer will keep you posted on its progress and automatically return to its normal state, which will be BUSY if it is in the process of printing other jobs. Important Configuration Basics: Printer Cancel Job 75 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 74
printing, the Cancel Job icon will be displayed on the printer panel. Touch the icon. 2 In the "Print" column, select the job you want to cancel by touching the print job icon. 3 Touch the Delete Selected Job icon. 4 The screen will display a message to indicate that the job is being deleted. 5 The - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 75
, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch COMMON SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP There are four options in the COMMON SETUP menu structure: • Disconnect Ses • Reset TN Session • SCS Debug Trace Operations - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 76
How to access the Menu Settings Page • Reset ALL Def You will always be able to see the selected value for each option on the Menu Settings page. • From the Operator Panel: Select Menus > Reports > Menu Settings Page. • Through the http (browser) user interface: Connect to the print server by - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 77
Ses. Reset TN Session Do Not Reset, Reset TN Ses. SCS Debug Trace Disable *, PAR Std. Output, PAR Slot# Output, USB Std. Output, USB Slot# Output Reset ALL Def Do Not Reset, Reset All A description of the COMMON SETUP menu items follows. Operations - Common Setup: Menu Options Overview 79 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 78
printer is powered Off and On or when a Reset TN Ses. is performed. See the Reset TN Session option below. A Disconnect Ses. should be performed before powering Off the printer Disconnect ALL active TNe sessions. The printer must be powered Off and On or a Reset TN Ses. must be performed before the - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 79
Reset TN Session IMPORTANT: Powering the printer Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP=> Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. This option - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 80
) and output (ASCII) data. The trace menu option allows you to enable tracing and choose where the trace data should be sent. Because tracing will decrease printing performance, it should only be enabled when needed by service personnel for troubleshooting and service. NOTE: If the SCS/TNe Emulation - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 81
data output. # is a number representing the slot in which the optional USB card is installed. NOTE: Only the interfaces installed in the printer will be displayed. Optional cards may be added to provide additional ports for output of the debug trace data. Operations - Common Setup: SCS Debug Trace - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 82
panel. Restore ALL SCS/TNe emulation option settings to factory defaults. All sessions will be disconnected. All TNe sessions will have to be reconfigured. Other printer emulation settings (PCL, PS, IPDS, etc.) are not reset when this option is selected. Operations - Common Setup: Reset ALL Def 84 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 83
printing from a Mainframe host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TNE3270E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed under the sub-menus accessed from the TN3270E - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 84
Tree diagram of the TN3270E SETUP menu structure. Operations - TN3270E SETUP: Introduction 86 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 85
to a value setting indicates that the setting is currently active. The current setting for each option is listed on the Menu Settings page ("How to access the Menu Settings Page" on page 78). Options using text strings as settings which have not been configured display the text string "[undefined - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 86
An Advanced IDB language command line is shown at the end of menu options which may be set by remote configuration. This shows how to remotely set the menu option to the factory default using the Advanced IDB language (cf. "IDB Basics" on page 248 ff.) Operations - TN3270E SETUP: Introduction 88 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 87
Messages. Refer to Connect Status (page 92) for a description of each message. Sub-menu. See NETWORK SETUP> SERVER INFO Menu: Options Overview (page 95) and Name / IP Address (page 96). A description of each NETWORK SETUP menu option follows. Operations - TN3270E SETUP: NETWORK SETUP Menu: Options - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 88
. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN3270E SETUP: NETWORK SETUP > Print - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 89
TN3270 Defaults This Network Setup option restores the TN3270e NETWORK SETUP factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 90
Status This Network Setup option displays the connection status with the host. The option cannot be changed by the user. Normally only the primary status is shown. If problems occur, a last response message is appended to the primary status message. The complete status message text may not be - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 91
. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. The SCS/TNe Emulation is contacting the host or SNA Server to establish a TCP/IP connection. Comments The Telnet server does NOT support the device type - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 92
SCS/TNe Emulation used the CONNECT command in its request for a specific printer. The device name requested is the partner to some terminal. Lst Rsp:Error occured An unknown error when processing the device type or name has occurred. Operations - TN3270E SETUP: NETWORK SETUP > Connect Status 94 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 93
up to 10 characters Device Type Specific *, Associated, Generic Keep Alive Type Telnet NOP *, None, Timing Mark Keep Alive Time 45 *, range: 1 - 32000 [seconds] A description of each SERVER INFO menu option follows. Operations - TN3270E SETUP: NETWORK SETUP> SERVER INFO Menu: Options Overview - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 94
Emulation uses to contact the host or Telnet server. Option Value Use IP Address * Use Hostname Comments Use the IP address specified with the IP Address option. Use the hostname specified with the Hostname option. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Name / IP Address 96 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 95
IP Address This Network Setup > Server Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > IP - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 96
name used to identify the host to be contacted by the SCS/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Hostname 98 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 97
selected. While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > TN Server - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 98
Connect Status option or on the Menu Settings page ( "How to access the Menu Settings Page" on page 78). Check with your system administrator for the correct LU name to use. Option Value [undefined] * Comments Any ASCII text string up to 10 characters. Operations - TN3270E SETUP: NETWORK SETUP - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 99
This Network Setup > Server Info option specifies the device type for the LU Name requested from the host or the SNA gateway by the SCS/TNe Emulation. Check with your system administrator for the correct device type to use. Option Value Specific * Associated Generic Comments Request a specific LU - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 100
the selected signal type, try changing to another type. Check with your system administrator to determine the type of signal to select. This Network Setup > Server Info option specifies the type of keep alive signal sent to the host or SNA gateway server. This signal is sent to the host by the - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 101
name is KEEPALIVE OPTIONS. It resides in the host IP profile dataset: SYS1.TCPPARMS(PROFILE). This setting is not used if the Keep Alive Type is set to None. Option Value 45 * [1..32000] Comments The range is 1 to 32000 seconds. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Keep - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 102
OPTIONS menu. SCS OPTIONS Option name COR/APO Sett (IDB Option 122) MISC SETTINGS PAPER SETTINGS Values Yes *, No Sub-menu. See SCS Options > MISC SETTINGS Menu: Options Overview (page 106) and FF Support (IDB Option 5) (page 108). Sub-menu. See SCS Options > PAPER SETTINGS Menu: Options Overview - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 103
from the host. If the document does not fit on a page in portrait orientation, the orientation is changed to landscape. Option Value No Yes * IDB Value 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:2:EXIT Operations - TN3270E SETUP: SCS OPTIONS > COR/APO Sett (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 104
menu. SCS OPTIONS >MISC SETTINGS Option name FF Support (IDB Option 5) Non-Print Char (IDB Option 3) CSC Characters (IDB Options 8 & 9) IDB Delimiter (IDB Option 7) Use IR (IDB Option 21) Format Ctrl Sup (IDB Option 177) Country Code (IDB Option 2) Skip Blank Page (IDB Option 32) CPI (IDB Option - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 105
name Max Prt Pos (IDB Option 102) LPI (IDB Option 105) Line Spacing (IDB Option 106) LPP (IDB Option 107) Transparency (IDB Option 167) Form Strings (IDB Option 168) IBM Trn Code (IDB Option 169 bit 1) Leadin Sequence (IDB Option 169 bit2) Euro Support (IDB Event 191) BOLD PRINT Values 132 *, range - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 106
when the MPL (Maximum Page Length) or BM (Bottom Margin) is reached in the data stream. Option Value Always FF * Always LF LF & FF IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 5:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > FF Support (IDB Option 5) 108 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 107
Non-Print Char (IDB Option 3) This SCS Options > MISC Settings option defines the replacement character to substitute for an unprintable character found in the data stream. Refer to "Appendix B - ASCII Character Table" on page 282 for a complete list of printable characters and their values. - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 108
printer, e.g. &%1B = . The IDB option values are ASCII characters in the decimal range 33 - 126. Refer to "Appendix B - ASCII Character Table" on page is done by writing the number of the first option and separating the values for the preceding options with commas. Option Value &% * IDB Values - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 109
- 126. Refer to "Appendix B - ASCII Character Table" on page 282 for a complete list of characters and their values. Option Value : * IDB Value 58 [colon (:)] Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IDB Delimiter (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 110
sent when the printer reports a Paper Out, Paper Jam, goes Off-line etc. Option Value Off * On Value Description No IR signals are sent IR signals are sent IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 21:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Use - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 111
function is disabled. It can be enabled with the -M command. Note: Because control codes are suppressed, horizontal/vertical tab and other commands which depend on correct page format will not work correctly. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 113 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 112
auto-NL function is still enabled. NOTE: = &% is factory default. + M [m]: If Option 177 = 0, 1 or 2: After this command the auto-NL function is disabled. All host generated control codes are still sent to the printer. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 113
the printer with one of the transparent commands. NOTE: The effect of the +M command is reset per job. - M [m]: After this command, all Host generated control codes are processed and the auto-NL function operates as normal. Refer to "Appendix C - Special TN3270e IDB Commands" on page 284 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 114
Code (IDB Option 2) This SCS Options > MISC Settings option defines the character set. Option Value Aus/Ger Aus/Ger (alt) Belgian Brazilian Can Bilin Can French Dan/Nor Dan/Nor (alt) English (UK) English (US) * Fin/Swe Fin/Swe (alt) Fre/Azerty International Italian IDB Value 2 3 4 5 6 7 8 9 10 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 115
the SCS options are restored to non-US factory defaults, the default value of this option changes to English (UK). See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:1:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 117 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 116
pages are printed. With this option enabled, pages containing only a CR, NL, LF or FF are skipped. Option Value Do Not Skip * Skip IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 32:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Skip Blank Page (IDB Option - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 117
CPI (IDB Option This SCS Options > MISC Settings option defines the number of 100) characters per inch. Option Value 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 10 12 15 16 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CPI - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 118
Max Prt Pos (IDB This SCS Options > MISC Settings option defines the maximum Option 102) number of characters per line. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:132:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Max Prt Pos - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 119
LPI (IDB Option This SCS Options > MISC Settings option defines the number of 105) lines per inch. Option Value 6 * [1..255] IDB Value 6 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPI (IDB Option 105) 121 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 120
Line Spacing (IDB Option 106) This SCS Options > MISC Settings option defines the line spacing. Option Value Single * Double IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 106:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Line Spacing (IDB Option 106) 122 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 121
LPP (IDB Option 107) This SCS Options > MISC Settings option defines the number of lines per page. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 122
SCS Options > MISC Settings option selects the transpar(IDB Option 167) ency mode. Option Value Intermate * Axis Enable MPI feat IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 167:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Transparency (IDB Option 167 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 123
is an ASCII character in the decimal range 0 255. Refer to "Appendix B - ASCII Character Table" on page 282 for a complete list of printable characters and their values. Option Value ASCII Value 0 * ASCII Value [1..255] IDB Value 0 1 - 255 Comments Disable the Formatted String Utility. Advanced - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 124
is performed. All transparent data is printed, even invalid data, ie data in the range 40H - FEH. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IBM Trn Code (IDB Option 169 bit 1) 126 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 125
trans- parent handling. 1 User defined transparent lead in characters are used without the pass through sequence. See the CSC Characters (IDB Options 8 & 9) option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Leadin - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 126
(IDB Event 191) print support. Option Value No * Yes Comments Disable Euro Support. Enable Euro Support. The ASCII character 186d (0xBAh) is converted to the Euro ASCII character 213d (0xD5h) in symbol set 13U. Operations - TN3270E SETUP: MISC SETTINGS > Euro Support (IDB Event 191) 128 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 127
> BOLD PRINT Menu - Options Overview The BOLD PRINT menu is a sub-menu under the MISC SETTINGS menu. The following table lists menu options found under the BOLD PRINT menu. SCS OPTIONS > MISC SETTINGS> BOLD PRINT Option name Bold On CR (IDB Option 22 bit 1) Bold On BS (IDB Option 22 bit 2) Bold - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 128
MISC Settings > BOLD PRINT option defines Option 22 bit 1) whether or not bold printing is enabled on a carriage return (CR). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 129
> MISC Settings > BOLD PRINT option defines Option 22 bit 2) whether or not bold printing is enabled on a backspace (BS). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 130
> MISC Settings > BOLD PRINT option defines whether or not bold printing is enabled on multiple backspaces. Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On Multi BS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 131
Options > PAPER SETTINGS Menu: Options Overview The PAPER SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options found under the PAPER SETTINGS menu. Option name Left Margin (IDB Option 103) Right Margin (IDB Option 104) Top Margin (IDB Option 108) Bottom - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 132
A description of each PAPER SETTINGS menu option follows. Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 134 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 133
position in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Left Margin (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 134
in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:132:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Right Margin (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 135
Options > Paper Settings option defines line number position of the top margin. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN3270E SETUP - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 136
(IDB Option 109) This SCS Options > Paper Settings option defines the line number position of the bottom margin. The line height depends on the setting of the LPI (IDB Option 105) option. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 137
Source Input This SCS Options > Paper Settings option selects the input (IDB Option 113) source. Option Value Prtr Setting Tray 1 * Tray 2 Tray 3 Tray 4 Tray 5 IDB Value 0 1 2 3 4 5 Comments Feed paper from the paper source selected in the printer PAPER MENU Paper Source menu. Paper is fed from - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 138
SCS Options > Paper Settings option selects the page orien(IDB Option 123) tation for source input tray 1. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 139
SCS Options > Paper Settings option selects the page orien(IDB Option 124) tation for source input tray 2. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 140
SCS Options > Paper Settings option selects the page orien(IDB Option 125) tation for source input tray 3. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 125:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 141
SCS Options > Paper Settings option selects the page orien(IDB Option 126) tation for source input tray 4. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 142
SCS Options > Paper Settings option selects the page orien(IDB Option 127) tation for source input tray 5. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 143
SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 90:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray1 Paper Size (IDB Option 90 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 144
SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 91:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray2 Paper Size (IDB Option 91 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 145
SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 92:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray3 Paper Size (IDB Option 92 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 146
SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 93:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray4 Paper Size (IDB Option 93 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 147
SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 94:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray5 Paper Size (IDB Option 94 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 148
TEST OPTIONS Menu: Options Overview The TEST OPTIONS menu is a sub-menu directly under the TN3270E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS3270 Hex Dump Normal Mode *, Hex Dump-Mode Print 3270 IDB Do Not Print *, Print - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 149
enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means that a hex dump is not produced - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 150
prints a tabular report of the current IDB settings using option numbers. Print this report when asked by technical support representatives. Option Value Do Not Print * Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 151
below summarizes the differences between the US and the Non-US factory default settings. Affected option Country Code (IDB Option 2) Bottom Margin (IDB Option 109) LPP (IDB Option 107) Tray1 Paper Size (IDB Option 90) US-Default Non-US-Default English (US) English (UK) 64 66 64 66 Letter - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 152
(IDB Option 91) Tray3 Paper Size (IDB Option 92) Tray4 Paper Size (IDB Option 93) Tray5 Paper Size (IDB Option 94) FF Support (IDB Option 5) COR/APO Sett (IDB Option 122) US-Default Letter Letter Letter Letter Always FF Yes Non-US-Default A4 A4 A4 A4 Always FF Yes Operations - TN3270E SETUP: TEST - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 153
from an AS/400 or iSeries host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TN5250E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed under the sub-menus accessed from the TN5250E - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 154
Tree diagram of the TN5250E SETUP menu structure. Operations - TN5250E SETUP: Introduction 156 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 155
to a value setting indicates that the setting is currently active. The current setting for each option is listed on the Menu Settings page. ("How to access the Menu Settings Page" on page 78) Options using text strings as settings which have not been configured display the text string "[undefined - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 156
for the User IDB language and another for the Advanced IDB language. These show how to remotely set the menu option to the factory default or how to perform the described action (cf. "IDB Basics" on page 248 ff. - and see "Additional TN5250e Printer Commands Using IDB" on page 260 ff.) Operations - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 157
to Connect # Status (page 162) for a description of each message. SERVER # INFO Sub-menu. See CONNECTION # > SERVER # INFO Menu: Options Overview (page 165) and Name / IPaddress # (page 166). A description of each CONNECTION## menu option follows. Operations - TN5250E SETUP: CONNECTION # Menu - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 158
. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN5250E SETUP: CONNECTION # > Print - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 159
settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed in the operator panel. Restore the TN5250 CONNECTION ## menu options for the current connection to factory - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 160
a session from being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #). 2 NPA Mode = Off. Solution: Set to Auto. (Path: Menus > Network/Ports > print server to be used for SCS printing > NPA Mode). 3 Cable is not - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 161
Connect # Status: Primary status messages Comments Session Disconnected and Halted All active Telnet sessions have been disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. Session - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 162
error Lst Rsp:8922:Negative response received Lst Rsp:8923:Start-up record incorrectly Lst Rsp:8925:Creation of device failed Lst Rsp:8928:Change of device failed Lst Rsp:8929:Vary on or vary off failed Lst Rsp:8930:Message operator. Operations - TN5250E SETUP: CONNECTION # > Connect # Status 164 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 163
] *, ASCII name with up to 16 characters Server # TN Port 23 * or within the range 0 - 65000 Device # Name [undefined] *, ASCII name with up to 10 characters Keep Alive Type None *, Telnet NOP, Timing Mark Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO Menu: Options Overview 165 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 164
[seconds] QSYSOPR *, ASCII name with up to 10 characters. *LIBL *, ASCII name with up to 10 characters. Normal *, Offline, No Reply No *, Yes A description of each SERVER # INFO menu option follows. Name / This Connection# > Server# Info option specifies the kind of IPaddress # address the SCS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 165
IP # Address This Connection# > Server# Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > IP # - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 166
used to identify the host to be contacted by the SCS/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Hostname # 168 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 167
. While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Server # TN - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 168
associated with the SCS/TNe Emulation on the host. A device and writer will be auto configured with this name if it does not already exist. Option Value [undefined] * Comments Any ASCII text string up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Device # Name 170 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 169
with your system administrator to determine the type of signal to select. This Connection# > Server# Info option specifies the type of keep alive signal sent to the host. This signal mark as the keep alive signal. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Keep Alive Type 171 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 170
host. This will help minimize network traffic. This Connection# > Server# Info option specifies the time in seconds that option value to a value less than the INACTTIMO value on the host. Option Value 45 * [1..32000] Comments The range is 1 to 32000 seconds. Operations - TN5250E SETUP: CONNECTION - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 171
created. The MSGQ # Lib option may be used to set the message queue library. Leave this option at the default if you do not know the message queue name. Option Value QSYSOPR * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > MSGQ - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 172
Name option. The message queue library must already exist on the host. It will not be auto created. Leave this option at the default if you do not know the library name. Option Value *LIBL * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 173
. Option Value Normal * Offline No Reply Comments Use normal IR replies, i.e. send paper jam as paper jam, paper out as paper out etc. Only send IR replies as offline messages without specifying what kind of IR has occurred. Disable the use of IR replies. Operations - TN5250E SETUP: CONNECTION - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 174
due to the host's management of the print queue when more than one job is in the same queue. Option Value No * Yes Comments Do not sense if writer ends. Sense if writer ends, reconnect, and reconfigure automatically. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Auto Sense # END 176 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 175
Hor/Ver (IDB Option 158) Use Escape *, Use Line feed, Space + Escape, Linefeed + Esc Format Ctrl Sup (IDB Option 177) Enabled *, Disabled Download Font (IDB Option 244) Enabled *, Disabled Euro Support (IDB Option 139) No *, Yes Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 177 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 176
-menu. See SCS OPTIONS > COR/APO SETTINGS Menu: Options Overview (page 198) and Def Page Ori 1 (IDB Option 121) (page 199). Sub-menu. See SCS OPTIONS > MISC SETTINGS Menu: Options Overview (page 208) and Country Code (IDB Option 2) (page 210). Sub-menu. See SCS OPTIONS > PAPER SETTINGS Menu: Options - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 177
be executed at the top of each page. OVLDRW command 1 will be executed if paper tray 1 has been selected and OVLDRW command 2 will be executed if paper tray 2 has been selected. Option Value Disable * Enable IDB Value 0 1 User IDB parameter OFF ON User IDB command: OVLCAL : Parameter - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 178
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 28:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 180 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 179
a single font, it is recommended to use the P value for the parameter in the PRGFNT command. Option Value Do Not Use * Use IDB Value 0 1 User IDB parameter OFF ON User IDB command: PRPFNTMOV : Parameter: OFF, ON Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 180
User IDB language to set factory default: &%IDB_EDIT: PRPFNTMOV OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 118:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 182 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 181
as shown. 10 CPI => 10.2 CPI 12 CPI => 12.2 CPI 15 CPI => 15.3 CPI Formula for calculating other values: Compress CPI = C-----P----I---×-----5---0-49 Option Value Off * On IDB Value 0 1 User IDB parameter OFF ON Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 183 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 182
User IDB command: COMCPI : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: COMCPI OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 128:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 184 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 183
: HORMOV / VERMOV : Parameter: For HORMOV ESC uses escape sequences; SP uses spaces For VERMOV ESC uses escape sequences; LF uses line feeds User IDB language to set factory default: &%IDB_EDIT: HORMOV ESC: VERMOV ESC:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 184
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 158:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 186 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 185
TNe Emulation. If the printout is incorrectly double spaced, disabling it will in most cases solve the problem. Option Value Enabled * Disabled IDB Value 0 1 User IDB parameter ON OFF User IDB command: CTLCODSUP : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 186
that these fonts will be downloaded to the printer's memory at Power On. The additional fonts are listed in the table below. The fonts marked with a + contain the Euro character. Option Value Disabled Enabled * IDB Value 0 1 User IDB parameter Not supported Not supported Font IBM font no. PCL - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 187
User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 244:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 189 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 188
Support (IDB Option 139) This SCS Options option controls Euro character printing. If the option is set to Yes, the normal code pages are re-mapped to code pages containing the Euro character. This means that the international currency symbol is replaced with the Euro character in the EBCDIC code - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 189
Euro character a font supporting the character also has to be selected and available in the printer. See the Download Font (IDB Option 244) option on page 188 and the Font (IDB Options 242 and 243) option on page 215. Option Value No * Yes IDB Value 0 1 User IDB parameter OFF ON User IDB command - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 190
OPTIONS > CSC CHARACTERS Menu: Options Overview The CSC CHARACTERS menu is a sub-menu directly under the SCS OPTIONS menu. The following table lists menu options found under the CSC CHARACTERS menu. SCS OPTIONS > CSC Characters Option name IDB First Char (IDB Option 8) IDB Second Char (IDB Option - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 191
"Appendix B - ASCII Character Table" on page 282 for a complete list of characters and their values. Option Value & * IDB Value 38 [ampersand] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 192
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB Option 8) 194 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 193
"Appendix B - ASCII Character Table" on page 282 for a complete list of characters and their values. Option Value % * IDB Value 37 [percent] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 194
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 9:37:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB Option 9) 196 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 195
33 - 126. Refer to "Appendix B - ASCII Character Table" on page 282 for a complete list of characters and their values. Option Value : * IDB Value 58 [colon] User IDB parameter Not supported User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 196
> COR/APO SETTINGS Menu: Options Overview The COR/APO SETTINGS menu is a sub-menu directly under the SCS OPTIONS menu. The following table lists menu options found under the COR/APO SETTINGS menu. SCS Options > COR/APO Settings Option name Values Def Page Ori 1 (IDB Option 121) Portrait *, Prtr - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 197
option defines the page orientation for paper tray 1. The option setting is only used when the APO/COR (Automatic Page Orientation / Computer Output Reduction) function is disabled with the COR Action 1 (IDB Option 123) option. Option Value Prtr Setting Portrait * Landscape IDB Value 0 1 2 User - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 198
the page orientation for paper tray 2 and above. The option setting is only used when the APO/COR (Automatic Page Orientation / Computer Output Reduction) function is disabled with the COR Action 2 (IDB Option 124) option. Option Value Prtr Setting Portrait * Landscape IDB Value 0 1 2 User IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 199
123) This SCS Options > COR/APO Settings option defines how the APO/COR function (Automatic Page Orientation/Computer Output Reduction) works for paper tray 1. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 200
OFF APO COR STODIS User IDB command: CORDRW 1 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 1 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 201
defines how the APO/COR function (Automatic Page Orientation/Computer Output Reduction) works for paper tray 2 and above. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between Landscape - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 202
OFF APO COR STODIS User IDB command: CORDRW 2 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 2 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 203
be possible to control the print quality of the jobs printed from the host, this option is used to disable text mode. When text mode is disabled, the APO/COR D - COR/APO Logic (TN5250e)" on page 287 Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > PPM Quality Dis (IDB Opt.126) - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 204
IDB command: TXTMOD : Parameter: OFF, ON, APO User IDB language to set factory default: &%IDB_EDIT: TXTMOD OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > PPM Quality Dis (IDB Opt.126) 206 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 205
LINSPRED : Parameter: 1 - 100 percent of normal line spacing User IDB language to set factory default: &%IDB_EDIT: LINSPRED 70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:70:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR LSI Reduc (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 206
SCS OPTIONS > MISC SETTINGS Menu: Options Overview The MISC SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options and sub-menus found under the MISC SETTINGS menu. SCS OPTIONS>MISC SETTINGS Option name Country Code (IDB Option 2) Codepage (IDB Options 240 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 207
*, Paper Media, Envelope Med Prtr Setting *, Output Bin 1, Output Bin 2, Output Bin 3 Prtr Setting *, Simplex, Duplex, Duplex (Tumble) ASCII Value 45, any single ASCII character in the decimal range: 0 - 255 A description of each MISC SETTINGS menu option follows. Operations - TN5250E SETUP: SCS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 208
all country codes. In country codes other than International country specific characters replace selected characters. Option Value International * USA/Can Ger/Aus Belgium Brazil Can/Fre Den/Nor Fin/Swe France Italy Jap (Latin) USA/Can bil. Portugal IDB Value 0 1 2 3 4 5 6 7 8 9 10 11 12 User IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 209
User IDB command: DEFCNTCOD : Parameter: 0 - 15 User IDB language to set factory default: &%IDB_EDIT: DEFCNTCOD 0:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Country Code (IDB Option 2) 211 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 210
is commonly used by AS/400 and iSeries computers. If Euro Support has been enabled with the Euro Support (IDB Option 139) option, code pages 37, 273, 277, 278, 280, 284, 285, 297, 500 and 871 are remapped to the code pages 1140 - 1149. Option Value USA/Can 37 Math 259 Ger/Aus 273 Belgium 274 Brazil - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 211
(Option 240 and 241) User IDB parameter OCR 340 84 + 1 340 Multi 500 * 244 + 1 500 Iceland 871 103 + 3 871 Code pages with Euro support below 125 + 4 1149 User IDB command: DEFCODPAG : Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 213 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 212
Parameter: 37 - 1149 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFCODPAG 500:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 240:244: OPTION 241:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 214 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 213
system. Fonts in shaded rows may be loaded into printer memory. See the Download Font (IDB Option 244) option. Option Value (Font ID) Font Name 3 OCR-B 11 Courier 10 * 18 Courier It. 10 39 Got.Text Bld 10 40 Got.Text 10 46 Courier Bold 10 66 Got.Text 12 68 Got.Text Italic 69 Got - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 214
1053 Son.Ser.Bld 10 IDB Value (Option 242 and 243) User IDB parameter 155 + 0 155 159 + 0 159 160 + 0 160 163 + 0 163 175 + 0 175 204 + 0 204 221 + 0 221 222 + 0 222 223 + 0 223 230 + 0 230 244 + 0 244 245 + 0 245 252 + 0 252 253 + 0 253 25 + 1 281 34 + 1 290 239 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 215
>: Parameter: 3 - 2103 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFFNT 11:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 242:11: OPTION 243:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 and 243) 217 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 216
10 12 15 16 User IDB parameter 5 10 12 15 16 User IDB command: DEFCPI : Parameter: 5, 10, 12, 15, 16 User IDB language to set factory default: &%IDB_EDIT: DEFCPI 10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN5250E SETUP: SCS OPTIONS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 217
] IDB Value 80 User IDB parameter 80 User IDB command: DEFMPP : Parameter: 1 - 254 User IDB language to set factory default: &%IDB_EDIT: DEFMPP 80:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:80:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 218
IDB Value 1 User IDB parameter 1 User IDB command: DEFLFTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLFTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 219
IDB Value 1 User IDB parameter 1 User IDB command: DEFRGTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFRGTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 220
LPI (IDB Option This SCS Options > Misc Settings option selects the number of 105) lines per inch (LPI). Option Value 3 LPI 4 LPI 6 LPI * 8 LPI 9 LPI IDB Value 3 4 6 8 9 User IDB parameter 3 4 6 8 9 User IDB command: DEFLPI : Parameter: 3, 4, 6, 8, 9 User IDB language to set factory - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 221
Lines Per Page This SCS Options > Misc Settings option defines the number of (IDB Option 107) lines per page. Option Value 68 * [1..255] IDB Value 68 User IDB parameter 68 User IDB command: DEFLPP : Parameter: 0 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLPP 68: - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 222
IDB Value 1 User IDB parameter 1 User IDB command: DEFTOPMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFTOPMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 223
contain a string which selects a specific tray in the printer. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. User IDB command: DEFSRCDRW : Parameter: DEF, 1, 2, 3, 4, 5, 6, 7, 8 User IDB language to set - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 224
Forms Media (IDB Option 114) This SCS Options > Misc Settings option selects the paper tray. The setting will trigger definitions made by the Select Media (SLTMED) command. Option Value Prtr Setting * Paper Media Envelope Med IDB Value 0 1 2 User IDB parameter DEF PAP ENV User IDB command: - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 225
(IDB Option 115) This SCS Options > Misc Settings option selects the paper output bin. The setting will trigger definitions made by the Destination Drawer (DSTDRW) command. Option Value Prtr Setting * Output Bin 1 Output Bin 2 Output Bin 3 IDB Value 0 1 2 3 User IDB parameter DEF 1 2 3 User IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 226
(SLTSIMDUP) command. The tumble setting is used for pages connected or bound at the top. NOTE: The Duplex and Duplex (Tumble) settings display only on printers with duplex support. Option Value Prtr Setting * Simplex Duplex Duplex (Tumble) IDB Value 0 1 2 3 User IDB parameter DEF SIM DUP TUM - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 227
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 116:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Simplex/Duplex (IDB Option 116) 229 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 228
character or a character not supported by the SCS/TNe Emulation. Refer to "Appendix B - ASCII Character Table" on page 282 for a complete list of printable characters and their values. Option Value ASCII Value 45 * ASCII Value [0..255] IDB Value 45 0 - 255 User IDB parameter 45 All EBCDIC - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 229
under the SCS OPTIONS menu. The following table lists menu options found under the PAPER SETTINGS menu. SCS Options > Paper Settings Option name Left Margin COR (IDB Opt. 78 & 79) Top Margin COR (IDB Opt. 80 & 81) Left Margin Lan (IDB Opt. 86 & 87) Top Margin Lan (IDB Opt. 88 & 89) Page Length (IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 230
or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFCOR I 0.44:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 78:122: OPTION 79:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 231
number. 256 78: (Marg. inch × 1440) - (256 × Value stored in option 79) Round off to nearest whole number. The values stored in option can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt. 78 & 233 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 232
or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFCOR I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 80:0: OPTION 81:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 233
number. 256 80: (Marg. inch × 1440) - (256 × Value stored in option 81) Round off to nearest whole number. The values stored in option can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 & 235 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 234
or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFLAN I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 86:0: OPTION 87:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin Lan (IDB Opt. 86 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 235
number. 256 86: (Marg. inch × 1440) - (256 × Value stored in option 87) Round off to nearest whole number. The values stored in option be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin Lan (IDB Opt. 86 & 87) 237 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 236
] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFLAN I 0.10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 88:147: OPTION 89:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin Lan (IDB Opt - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 237
number. 256 88: (Marg. inch × 1440) - (256 × Value stored in option 89) Round off to nearest whole number. The values stored in option be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin Lan (IDB Opt. 88 & 89) 239 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 238
29.70 27.94 35.56 26.67 Length in inch. 11.70 11.00 14.00 10.50 Option value 16848 15840 20160 15120 User IDB command: PAGLNG : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. 82 & 83) 240 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 239
User IDB language to set factory default: &%IDB_EDIT: PAGLNG I 11.70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 82:208: OPTION 83:65:EXIT The option values for option inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. 82 & 83) 241 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 240
in cm 21.00 21.59 21.59 18.42 Width in inch. 8.27 8.50 8.50 7.25 Option value 11908 12240 12240 10440 User IDB command: PAGWDT : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Width (IDB Opt.84 & 85) 242 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 241
User IDB language to set factory default: &%IDB_EDIT: PAGWDT I 8.27:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 84:132: OPTION 85:46:EXIT The option values for option 3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Width (IDB Opt.84 & 85) 243 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 242
TEST OPTIONS Menu: Options Overview The TEST OPTIONS menu is a sub-menu directly under the TN5250E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS5250 Hex Dump Normal Mode *, Hex Dump-Mode Print 5250 IDB Do Not Print *, Print - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 243
enables hex tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means that a hex dump is not produced - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 244
by technical support representatives. Option Value Do Not Print Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the operator panel. Print the IDB settings. User IDB language: &%IDB_PRINT_FULL:EXIT Operations - TN5250E SETUP: TEST OPTIONS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 245
default values. Option Value Do Not Restore * Restore Defaults Comments Do not restore any settings. This performs the same action as if Back had been pressed in the operator panel. Restore to factory default TN5250E SCS option menu settings. Operations - TN5250E SETUP: TEST OPTIONS > SCS5250 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 246
given in the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. The IDB Languages Both TN3270E and TN5250E users can use the Advanced IDB Language to access and configure/customize the SCS options found in the protocol conversion tables - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 247
somewhat easier to use. However, the User IDB Language is only available for working on approximately 20 of the most common IDB options. Working with the other options requires the use of the Advanced IDB Language. The IDB languages are to be used during initial setup or re-configuration of the SCS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 248
the Control Panel" on page 10 ff. "Operations Reference - TN3270E SETUP" on page 85 and "Operations Reference - TN5250E SETUP" on page 155. The descriptions include the available options and their values. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 260 covers IDB commands - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 249
settings with syntax or range errors are ignored. If the SCS/TNe Emulation prints out the commands, or prints out error messages, it could be because the characters used for programming (& % E : ...etc) have been corrupted. You must reset the SCS OPTIONS to their factory defaults. IDB Basics: IDB - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 250
the command: &%IDB_EDIT: and leave configuration mode, by sending the trailer string: EXIT This causes the changed options to be saved. The new option settings are active on the next SCS job. All configuration options must be separated by a colon. Line feed, form feed etc. should be avoided, but are - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 251
&%idb_edit:DEFCODPAG 37:EXIT Option values Refer to the option descriptions in chapter "Operations Reference TN3270E SETUP" on page 85 and in chapter "Operations Reference - TN5250E SETUP" on page 155. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 260 covers IDB commands - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 252
convenient as the contents of all IDB options and events are viewed and edited on a PC screen. After the editing is done, it is possible to save the settings in a file. The resulting IDB Configuration File can then be downloaded to one or more printers containing an SCS/TNe Emulation providing easy - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 253
changed. The procedure below uses a Microsoft FTP client. To retrieve the IDB settings file 1 Start a FTP session. ftp 201.1.12.123 (Sample IP address) User name: 2 Enter the "/lti" directory. cd /lti 3 Set the FTP client to binary mode. This is necessary as data is transferred in binary - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 254
5 End the FTP session. bye IDB Basics: Retrieving the IDB Configuration File 256 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 255
site with manual updates listed in "Support" on page 4. Look for Menu Settings Page shows the text string "[invalid]" for options set outside their ranges. The retrieved IDB file contains additional options and events not described in this guide. Only options and events described in this guide - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 256
. The download file name is fixed. Downloading a file with a different name will result in an unreadable printout. No IDB settings will be changed. The procedure below uses a Microsoft FTP client. To store the IDB settings file 1 Start a FTP session. ftp 201.1.12.123 (Sample IP address) User name - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 257
4 Store the IDB configuration file. put c:\tn3270e.idb put c:\tn5250e.idb (TN3270E users) (TN5250E users) This stores the file from a PC's root directory. 5 End the FTP session. bye The downloaded IDB settings are active on the next SCS job. IDB Basics: Storing the IDB Configuration File 259 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 258
recognized, i.e. included in the SCS data stream. The commands you may work with fall into three groups: 1 Paper Handling 2 Code Page Handling / Code Page 259 3 Miscellaneous See "IDB Basics" on page 248 ff. for background information on IDB. TN5250e Printer Commands Using IDB: Introduction 260 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 259
input data string () following some printer commands can contain three parts: Text, decimal numbers, and hexadecimal numbers. Text: Text has to be put in quotation marks. "This is a text" Decimal: Decimal numbers are entered normally. Use commas to separate. 12,34,24,67,12,3,45,6,7,90,255 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 260
On. The events can be used to download a small logo or set the printer to a specific emulation. Power On sequence 1 Power On, events 0, 1 and 2 are triggered. 2 DEFMPP (Max print positions) is selected. 3 DEFCPI (CPI) (option 100) triggers event 31, 32, 33, 34, or 35. 4 DEFLPI (LPI) is selected - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 261
> : POWON DEL : Parameter: 1 - 4 Example: POWON 3 "Power initialize 3": POWON DEL 3: Delete command Definition number The rest of this chapter is devoted to a run-through of the commands you can work with. TN5250e Printer Commands Using IDB: Initializing - Power On Initialize 263 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 262
tray. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. Command: SRCDRW -: SRCDRW DEL : Delete command Parameter: 1 - 3 , 4 - 8 Drawer number Example: SRCDRW 1 /1B,"&l1H": SRCDRW DEL 3: Set - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 263
Paper Handling > Destination Drawer This is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when a certain output drawer (bin) is selected. It can also be triggered by the DEFDSTDRW command at Power On. See section "Output Bin (IDB Option 115)" on page 227. The command - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 264
On. See section "Forms Media (IDB Option 114)" on page 226. The command corresponds to event 62 - 63. Command: SLTMED : SLTMED DEL : Delete command Parameter: PAP ENV Select paper media Select envelope media Example: SLTMED PAP "Paper media": SLTMED DEL ENV: TN5250e - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 265
: SLTPAPFED : SLTPAPFED DEL : Delete command Parameter: CON CUT MAN Select continuous paper feed Select cutsheet feed Select manual feed Example: SLTPAPFED MAN /1B,"&l2H": SLTPAPFED DEL CUT: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper Feed 267 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 266
Paper Handling > Select Simplex/Duplex Printing This is used when simplex or duplex printing is selected. The command can only be used if the printer supports duplex printing. It is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when simplex or duplex printing is selected. - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 267
" if it has been downloaded to the printer. It is also possible to select another font in the printer, e.g. a special mathematical font. The COD259 BEF command is executed each time there is a switch to code page 259 from another code page. It is not executed if code page 259 is selected repeatedly - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 268
Parameter: BEF AFT Before code page 259 selection After code page 259 selection Example: COD259 BEF "Command": COD259 DEL AFT: TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 270 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 269
immediately before the first printable character. See section "Overlay Call (IDB Option 28)" on page 179. OVLDRW command 1 is executed when paper tray 1 is selected and OVLDRW command 2 is executed when paper tray 2 is selected. The command corresponds to event 55 - 56. Command: OVLDRW - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 270
Formfeed Command: BEFAFTFED : BEFAFTFED DEL : Parameter: BEF AFT Example: BEFAFTFED BEF "Command": BEDAFTFED DEF AFT: Delete command Before formfeed After formfeed TN5250e Printer Commands Using IDB: Miscellaneous > Before / After Formfeed 272 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 271
selection Example: BEFPORLAN POR /1B,"&l0E",/1B,"&a0V": PCL command for setting top margin to 0 and moving print position to line 0 BEFPORLAN DEL LAN: TN5250e Printer Commands Using IDB: Miscellaneous > Before Portrait/Landscape Selection 273 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 272
of the first page. It may be used for stating specific information on the front page. This could be information describing which IDB profile is used, printer type, or IDB /0A,/0D,"SCS Printer": SUBTIT HEX "Setup for test 05-18-99": SUBTIT DEL HEX: TN5250e Printer Commands Using IDB: Miscellaneous - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 273
line 1 and no characters have been printed. The contents of the string could be PCL codes like: • Top margin setting to uppermost line. • Disable perforation skip. • Absolute vertical position to line 0 MOVUPRLIN DEL: TN5250e Printer Commands Using IDB: Miscellaneous> Move to Uppermost Line 275 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 274
Warranty included with the printer The limited warranty you received with your printer gives warranty terms and conditions. For warranty information, refer to your printer documentation. Warranty: included with the printer 276 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 275
3812-01 (5250 SCS) printer. One TN3270e connection is supported. Up to four TN5250e connections are supported. The SCS/TNe Emulation autodetects installed features to set initial settings for options such as duplex support (TN5250e only). Appendix - Specifications, Requirements, Features: Product - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 276
Compatibility IBM Printer Emulations • 3270 SCS: IBM 3287/3812 in LU1 mode • 5250 SCS: IBM 3812-01 Compatible Print Servers • Standard Network for connection to an Ethernet LAN. • MarkNet internal print server (Ethernet) Appendix - Specifications, Requirements, Features: Compatibility 278 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 277
AS/400 Operating System OS/400 V4R1R5, or V5R1-R3 or greater. • Application System AS/400 Operating System OS/400 V3R7 with PTFs installed. Appendix - Specifications, Requirements, Features: Print Platforms 279 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 278
: 3270 SCS Features supported are dependent upon host software for selection and use. • SCS (LU1) data stream • 5 bin paper input • EBCDIC character conversion • Text string conversion • IBM and 3rd party ASCII transparency modes • EBCDIC hex-dump Appendix - Specifications, Requirements, Features - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 279
/DCA L2 data streams • 5 bin paper input and duplex • Computer Output Reduction (COR) / Automatic Page Orienta- tion (APO) • IBM font selection using FGID or CPI • IBM ASCII transparency • Multiple code pages and box drawing • Full OfficeVision/400 support • User Configurable SCS Features • EBCDIC - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 280
80 68 h 104 21 ! 33 39 9 57 51 Q 81 69 i 105 22 " 34 3A : 58 52 R 82 6A j 106 23 # 35 3B ; 59 53 S 63 57 W 87 6F o 111 28 ( 40 40 @ 64 58 X 88 70 p 112 29 ) 41 41 A 65 59 Y 89 71 q 113 2A * 42 42 B 66 5A Z 90 72 r 114 2B - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 281
x 120 31 1 49 49 I 73 61 a 97 79 y 121 32 2 50 4A J 74 62 b 98 7A z 122 33 3 51 4B K 75 63 c 99 7B { 123 34 4 52 4C L 76 64 d 100 7C | 124 35 5 53 4D M 77 65 e 101 7D } 125 36 6 54 4E N 78 66 f 102 7E ~ 126 37 7 55 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 282
TN3270e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS IDB Dump > Print. Appendix - TN3270e IDB Commands: How to Print an IDB Report 284 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 283
List of Larger numbers indicate higher precedence. Commands Precedence Command Comments 5 HEXDUMP option 31 = 0 5 +M Suppress format control codes 5 -M Standard handling of format control codes 5 {XY}.... Enter special transparent mode (X = option 171, Y = option - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 284
Precedence Command 2 1 {XY} Comments Double CSC (prints ) Single transparent character Refer to the chapter on Understanding the Control Panel (page 10) if necessary. Appendix - TN3270e IDB Commands: List of Commands 286 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 285
from portrait to landscape based on menu option settings. The distinction is between page orientation (APO) and computer output reduction (COR) in the SCS/ TNe Emulation is switched on with the CORDRW command. The focus of this discussion is on how the printer automatic controls operate, as the user - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 286
set in the PAGLNG and PAGWDT option settings. Refer to section "Page Length (IDB Opt. 82 & 83)" on page 240 and to section "Page Width (IDB Opt.84 & 85)" on page 242, which together specify the maximum valid page size. Example: Use an A4 page format as valid page. Appendix - COR/APO Logic (TN5250e - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 287
reduced from normal line spacing to a percentage value according to the LINSPRED option setting. Refer to section "COR LSI Reduc (IDB Option 127)" on page 207. • Margins (offset) are set according to the LFTOFFCOR and TOPOFFCOR option settings. Refer to section "Top Margin COR (IDB Opt. 80 & 81)" on - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 288
the nearest smaller font. 4 Most program applications normally have a set of standard values for page length, characters per line etc. The user might have few or no possibilities off changing, e.g., the number of characters per line, which is normally set to 132 characters. Therefore a final control - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 289
file (CRTPRTF). Please consult your AS/400 or iSeries manuals for information on this subject. Defining the printer file to make the COR is normally done in connection with IPDS page printers as these printers do not support the APO/COR function. If the APO/COR is disabled (CORDRW 1/2 = OFF), the - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 290
Example: Disable COR and set Portrait as default orientation for drawer 2 only. CORDRW 2 = OFF and ORTDRW 2 = POR Flowchart See next page. Appendix - COR/APO Logic (TN5250e): Flowchart 292 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 291
Page Orientation Logic Flowchart Appendix - COR/APO Logic (TN5250e): Flowchart 293 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 292
IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN5250E SETUP > TEST OPTIONS > Print IDB Dump > Print. Appendix - TN5250e IDB Commands: How to Print an IDB Report 294 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 293
numbers codes Standard handling of format control Enter special transparent mode (X = Option 171, Y = Option 172) Double CSC (prints ) Single or Multibyte transparent character Print status dump Print font list Trig event no. X Refer to the chapter on Understanding the Control Panel (page 10 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 294
IBM font IDs (sent from the system) to the internal fonts used in the printer. The font table has a limit of 50 fonts + 3 fonts used for COR attempts to program more than 50 IBM fonts are made, it will print out a message and a font table status sheet. This status sheet has the IBM IDs indicated in - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 295
printer memory at Power On. The font table is prepared for using these fonts. The fonts are loaded with code page PC-850 (12U) and with font ID D10003, D10155, D10159, D10160, D10163 and D10175. The loading of these fonts can be disabled via the operator panel using the Download Font (IDB Option - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 296
The "Font" Programming Command This command corresponds to the advanced IDB language FONT command. Command: PRGFNT : PRGFNT DEL : NOTE: Try to avoid deleting the first 7 fonts listed in the status printout (&%IDB_STATUS), as these fonts represent the - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 297
Parameters: 0-65535 This value indicates the IBM font sent from the system. Note that the IBM font numbers are divided into the groups below. pitch area IBM fonts 10 pitch: 1-65 12 pitch: 66-153 proportional: 154-200 13 pitch: 201-210 15 pitch: 211-239 5 pitch: 240-249 17 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 298
It has to be programmed the same way as printer command input data. The parameter is optional. No string definition will delete the definition of 154 - 200). The spacing command should only be used when using downloaded proportional fonts with the correct character spacing. N This value is - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 299
causes the printer to handle the character spacing. If "P" is selected in connection with programming of a font in the IBM proportional spaced area (154-200), the SCS/TNe Emulation prepares itself for support for downloaded IBM PS fonts. This ensures correct spacing of downloaded proportional spaced - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 300
2 The downloaded font 10175 is sent when IBM font ID 160 (Essay) is sent from the system. Font ID 160 is within the "proportional spaced" font area, - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 301
printout (&%IDB_STATUS) represent the substitution fonts for the following areas. Pitch area 10 pitch: 12 pitch: prop SP : 13 pitch: 15 pitch: 17 pitch 7 4 5 6 2 Command: SETSUBFNT : NOTE: The font number must be a font number already present in the font table. Appendix - SCS - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 302
ID 67, but all font IDs sent from the system in the range 66-153, which are not present in the SCS/TNe Emulation with a specific font ID, are printed with the definition of font 86. Appendix - SCS TN5250eFont Table: Set Substituted Font ID 304 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 303
User's Guide Fourth Edition July 2009, Rev 004. The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 304
or both. Intelligent Printer Data Stream and IPDS are trademarks or registered trademarks of Ricoh Co., Ltd in the United States, other countries, or both. Lexmark and Lexmark with diamond design, trademarks are the property of their respective owners. Trademarks: SCS/TNe Emulation User's Guide 306 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 305
User's Guide Getting Started ...1 SCS/TNe in a LAN environment ...1 Documentation Overview ...1 Equipment Requirements and Specifications ...2 Support ...4 Customer Support ...4 Important Configuration Basics ...5 Introduction ...5 What are "IDB Options", "IDB events etc.? ...6 Setup Options - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 306
...64 Task 5 - Verifying the Host Connection ...69 SCS/TNe Cancel ...71 About Cancel Job ...71 Important! ...71 Printer Cancel Job ...72 MFP Cancel Job ...74 Operations Reference - Common Setup ...75 Introduction ...75 Menu Options Overview ...77 Disconnect Ses ...78 Reset TN Session ...79 SCS Debug - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 307
Reference - TN3270E SETUP 83 Introduction ...83 NETWORK SETUP Menu: Options Overview ...87 Print Active ...88 TN3270 Defaults ...89 Connect Status ...90 NETWORK SETUP> SERVER INFO Menu: Options Overview 93 Name / IP Address ...94 IP Address ...95 Hostname ...96 TN Server Port ...97 LU Name - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 308
22 bit 3) ...130 SCS Options > PAPER SETTINGS Menu: Options Overview 131 Left Margin (IDB Option 103) ...133 Right Margin (IDB Option 104) ...134 Top Margin (IDB Option 108) ...135 Bottom Margin (IDB Option 109) ...136 Source Input (IDB Option 113) ...137 Tray 1 Orient (IDB Option 123) ...138 Tray - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 309
185 Download Font (IDB Option 244) ...186 Euro Support (IDB Option 139) ...188 SCS OPTIONS > CSC CHARACTERS Menu: Options Overview 190 IDB First Char (IDB Option 8) ...191 IDB Second Char (IDB Option 9) ...193 IDB Delimiter (IDB Option 7) ...195 SCS OPTIONS > COR/APO SETTINGS Menu: Options Overview - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 310
Page (IDB Option 107) ...221 Top Margin (IDB Option 108) ...222 Source Input (IDB Option 113) ...223 Forms Media (IDB Option 114) ...224 Output Bin (IDB Option 115) ...225 Simplex/Duplex (IDB Option 116) ...226 Non-Print Char (IDB Option 3) ...228 SCS OPTIONS > PAPER SETTINGS Menu: Options Overview - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 311
- Power On Initialize ...260 Paper Handling > Source Drawer ...262 Paper Handling > Destination Drawer ...263 Paper Handling > Select Paper / Envelope Media 264 Paper Handling > Select Paper Feed ...265 Paper Handling > Select Simplex/Duplex Printing 266 Code Page 259 > Before/After ...267 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 312
Specifications, Requirements, Features 275 Product Description ...275 Compatibility ...276 Print Platforms ...277 Features List: 3270 SCS ...278 Features List: 5250 SCS ...279 ASCII Character Table ...280 - Lexmark W850 | SCS/TNe Emulation User's Guide - Page 313
SCS/TNe Emulation User's Guide ...303 Trademarks ...304 ...304 Table of Contents ...305 : 313
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
 |
 |
1
Getting Started:
SCS/TNe in a LAN environment
Card for IPDS and SCS/TNe -
SCS/TNe Emulation User’s Guide
Getting Started
SCS/TNe in a
LAN
environment
Thank you for purchasing the Card for IPDS and SCS/TNe.
The card provides high quality IBM host connectivity print output.
With the appropriate print server and host software, your printer or
Multifunction Product (MFP) becomes an IBM host workstation
printer capable of printing IPDS or SCS documents from an iSeries,
AS/400, or mainframe. For a more detailed product description, see
“Specifications, Requirements, Features” on page 277
.
I
MPORTANT
:
Unless otherwise stated, the term
printer in this manual refers to both printers and
MFPs.
SCS data is received in a LAN environment using the Telnet
extended protocol. The Card for IPDS and SCS/TNe adds support
for the TN3270E and the TN5250E protocols. A correctly configured
printer can receive, process, and print SCS print jobs received over
TCP/IP.
Documentation
Overview
This document deals only with setting up and using the
SCS/TNe
emulation
in the Card for IPDS and SCS/TNe. It will help you to
understand, use, and change option settings for receiving SNA