Lexmark X342N Service Manual - Page 33

Printer specific user attendance messages Continued, Start, Reset Printer, Message, Explanation - reset photoconductor

Get Lexmark X342N - Multi Function Printer PDF manuals and user guides
UPC - 734646256292
View all Lexmark X342N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

7003-XXX Printer specific user attendance messages (Continued) Message Explanation 34 Short Paper The MFP determines the paper length is too short to print the formatted data. This occurs when the MFP does not know the actual paper size loaded in the tray. Make sure the Paper Size setting is correct for the size paper that is being used. The following actions may be taken: Press or Start to clear the message and continue printing. Press Stop to cancel the job. 37 Insufficient Collation Area This message displays when the MFP memory is insufficient to collate the pages of the print job. Press or Start to clear the message. Press Stop to cancel the job. 38 Memory Full This message displays when the MFP is processing an incoming job and there is insufficient memory available to continue processing the job. The following actions may be taken: • Press or Start to clear the message and continue printing. • Press Stop to cancel the print job. Clearing the error this way may cause data loss. 54 Std Network Software Error This error displays when a network port is detected, but the MFP cannot establish communications with it. Press Go to clear the message. The MFP disables all communications to the network interface. 56 Standard USB Port Disabled Displayed when status is requested over the USB port, but the port has been disabled. Once the error has been displayed for the first time, reporting of further errors is suppressed until the menus are entered or the MFP is reset. The following actions may be taken: • Press Go to clear the message. The MFP discards any data received on the USB port. • Press Menu until Busy/Waiting appears, and select Reset Printer. 84 Photoconductor Life Warning This message displays when the photoconductor unit is near end of life. Press or Start to clear the message and continue printing. Press Stop to cancel the job being processed. 84 Replace Photoconductor This message displays when the photoconductor is at the end of life. The photoconductor must be replaced. 88 Toner Low This message displays when toner low occurs and the toner low alarm is activated. Press or Start to clear the message and continue printing. Press Stop to cancel the job being processed. Diagnostic information 2-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
Diagnostic information
2-11
7003-XXX
34 Short Paper
The MFP determines the paper length is too short to print the formatted data.
This occurs when the MFP does not know the actual paper size loaded in the
tray. Make sure the Paper Size setting is correct for the size paper that is being
used.
The following actions may be taken:
Press
or
Start
to clear the message and continue printing.
Press
Stop
to cancel the job.
37 Insufficient
Collation Area
This message displays when the MFP memory is insufficient to collate the
pages of the print job.
Press
or
Start
to clear the message.
Press
Stop
to cancel the job.
38 Memory Full
This message displays when the MFP is processing an incoming job and there
is insufficient memory available to continue processing the job. The following
actions may be taken:
• Press
or
Start
to clear the message and continue printing.
• Press
Stop
to cancel the print job.
Clearing the error this way may cause data loss.
54 Std Network
Software Error
This error displays when a network port is detected, but the MFP cannot
establish communications with it.
Press
Go
to clear the message. The MFP disables all communications to the
network interface.
56 Standard USB
Port Disabled
Displayed when status is requested over the USB port, but the port has been
disabled. Once the error has been displayed for the first time, reporting of further
errors is suppressed until the menus are entered or the MFP is reset.
The following actions may be taken:
• Press
Go
to clear the message. The MFP discards any data received on the
USB port.
• Press
Menu
until
Busy/Waiting
appears, and select
Reset Printer
.
84 Photoconductor Life
Warning
This message displays when the photoconductor unit is near end of life.
Press
or
Start
to clear the message and continue printing.
Press
Stop
to cancel the job being processed.
84 Replace Photoconductor
This message displays when the photoconductor is at the end of life. The
photoconductor must be replaced.
88 Toner Low
This message displays when toner low occurs and the toner low alarm is
activated.
Press
or
Start
to clear the message and continue printing.
Press
Stop
to cancel the job being processed.
Printer specific user attendance messages (Continued)
Message
Explanation