Lexmark X464 SCS/TNe Emulation User's Guide
Lexmark X464 Manual
 |
View all Lexmark X464 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark X464 manual content summary:
- Lexmark X464 | SCS/TNe Emulation User's Guide - Page 1
Emulation User's Guide Getting Started SCS/TNe in a LAN environment IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. Thank you for purchasing the Card for IPDS and SCS/TNe. The card provides high quality IBM host connectivity print output. With - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 2
With the appropriate option card installed, the following printers and Muiltifunction Products (MFPs) are supported: • Lexmark C734, C736 • Lexmark E460dn, E460dw, E462dtn • Lexmark T650, T652 • Lexmark T654 • Lexmark T656dne • Lexmark W850 • Lexmark X463de, X464de Getting Started: Equipment - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 3
printer must have one of the following LAN connections: • Standard Network for connection to an Ethernet LAN (also called STD Net). • MarkNet internal print server (Ethernet). • Lexmark wireless internal print server. If you need to update your Standard Network or MarkNet firmware, refer to "Support - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 4
If you cannot find answers in this guide about using the SCS/TNe emulation, refer to the web site below. If you need to update your Standard Network, MarkNet internal print server, or SCS/TNe firmware, go to http://support.lexmark.com. You may also contact your point of purchase or your local - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 5
Important Configuration Basics Introduction IMPORTANT: Unless otherwise noted, the term printer refers to printers and MFPs, and the term control panel refers to operator panels and touch screens on these types of products. SCS/TNe MENU options settings can be changed and saved in three ways: • - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 6
Emulation user default settings remain in effect until you save new settings or restore the factory defaults by using one of the SCSxxxx Defaults options under MENU/Menus > Option Card Menu > SCS/TNe MENU > TNxxxE STEUP > TEST OPTIONS. xxxx stands for 3270 or 5250. Important Configuration Basics - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 7
SCS print job may override the user default settings displayed in the printer operator panel. This guide discusses setting up the SCS/TNe Emulation and changing the SCS/TNe Emulation settings. Printer Setup Options Changes to printer settings under the various printer menus, such as Paper Menu and - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 8
printers and touch screens on MFPs are illustrated here. If you are familiar with the use of the control panel, skip this chapter, but we recommend familiarizing yourself with the contents of "Remote Configuration Using a Browser" on page 24 before proceeding with installation setups. Descriptions - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 9
Printer operator Access the SCS/TNe Emulation options and settings from the operpanel ator panel SCS/TNe MENU. To reach the menu: Accessing the SCS/TNe menu 1 From a Ready status, press the MENU button . on the operator panel. This opens the menu index in the operator panel's screen. 2 Use the - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 10
. User-selected default settings remain in effect until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "Printer operator panel - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 11
the Country Code for TN3270. 1 Navigate to TN3270E SETUP. Press the Select button. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP 2 Navigate to SCS OPTIONS. Press the Select button. TN 3270 SETUP NETWORK SCS OPTIONS TEST OPTIONS Understanding the Operator Panel: Printer operator panel 13 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 12
3 Navigate to MISC SETTINGS. Press the Select button. SCS OPTIONS MISC SETTINGS Cor APO Sett TEST OPTIONS 4 Navigate to the Country Code option. Press the Select button. MISC SETTINGS Format Ctrl Sup Country Code Skip Blank Page Understanding the Operator Panel: Printer operator panel 14 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 13
setting is marked with an asterisk *, and in this example, it just happens to be factory default. If you want to change the setting, for example to Fin/Swe, use the navigation /Swe (alt) 6 While the printer is saving the setting, it will display Submitting Selection. Understanding the Operator Panel - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 14
menu group, press the Back button and then use the navigation buttons and press Select. 9 When you are finished, exit by pressing the Back button to return to the Ready screen. You may need to press it several times until the screen appears. Understanding the Operator Panel: Printer operator - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 15
is that the value you select consists of several fields. For example, if you select MENU > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #1 > SERVER 1 INFO > MSGQ 1 Name, you see the following display all the characters. Understanding the Operator Panel: Printer operator panel 17 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 16
a menu item that has a numerical value, you can usually choose between scrolling just as you would to select any value, or using the numerical pad. If the setting has more than one field, navigate as shown in "Changing a Text String" on page 17. Understanding the Operator Panel: Printer operator - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 17
MFP Touch Access the SCS/TNe Emulation options and settings from the operScreen ator panel SCS/TNe MENU. To reach the menu: Accessing the SCS/TNe menu 1 Make sure that the printer is on and the Ready message appears. 2 Touch the key icon (Menus) on the operator panel 3 Touch or to scroll - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 18
settings remain in effect until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "MFP Touch Screen" on page 19. 2 For this example - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 19
(Back) and no changes will be saved. 9 While the printer is saving the setting, Submitting Selection will be displayed. Changing a Text String Here is an example. 1 Select Menus > Option Card Menu > SCS/TNe Menu > TN3270e Setup > Network Setup > Server Info. 2 Touch the Keyboard symbol by LU Name - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 20
Enter (on some MFPs touch Submit) when you have completed the name. The screen returns to the previous menu level. 6 Touch (Submit) to save changes. Changing a Numerical Setting Example: If you select Menus > Option Card Menu > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > Keep - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 21
Some numerical values contain more than one field. For example, Menus > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > IP Address. For these, use the Keyboard as described in "Changing a Text String" on page 21. Understanding the Operator Panel: MFP Touch Screen 23 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 22
most SCS/TNe settings. The only requirement is that the printers are attached to a LAN using a Standard Network port or MarkNet internal print server. Remote configuration is especially useful during printer installation to set all of the SCS/TNe options to the values recommended by your system - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 23
the printer web page by typing the IP address of its print server as the URL. 2 Select Settings. 3 Select SCS/TNE Settings. 4 Select the TNe Common menu on each TNxxxx Connection Status menu item to check the status of each session. Remote Configuration Using A Browser: How to Use the Browser - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 24
printing or end the session from the host. If no jobs are printing, you may need to end and reset new values to the printer. These values are saved in the printer and will become active menu. 15 Reset all sessions by clicking on the Execute button next to the Reset TN Sess item. Remote Configuration - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 25
sure that all sessions have been reconnected. Click on each TNxxxx Connection Status menu item to check the status of each session. If all configured sessions have not been established within 90 seconds, you may need to end and reset the sessions at the host and repeat steps 14 - 16. On each TN - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 26
installation tasks, it is recommended that you obtain the latest version of the MarkNet internal print server firmware as well as the latest SCS/TNe publications and Card for IPDS and SCS/TNe code from the internet sites listed in "Support" on page 4. Mainframe Direct Users Task 1A - Configuring - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 27
Mainframe Direct Users SNA Server Users Task 6A - Verifying the Mainframe Connection Task 6B - Verifying the Mainframe/SNA Server Connection Mainframe Installation Setup: Introduction 29 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 28
Telnet protocols to print SCS jobs to a LAN attached printer. "Mainframe Software" on page 279 lists versions which support these protocols. The printer with the SCS/TNe Emulation is defined to the host like a normal LU-1 (SCS) printer. Three sample configurations follow. Sample Configuration number - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 29
Sample Configuration number 2: PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, =4,MODETAB=MTP3816, DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1A - Configuring the Host 31 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 30
EJ3270 APPL AUTH=NVPACE,EAS=1,PARSESS=NO, MODETAB=MODETAB2,SESSLIM=YES,DLOGMOD=SCS NOTE: IMLU1; DHW3270; and EJ3270; are the printer devices. SC0TCP01 is a terminal device, and is not needed for printer definitions in this node. Mainframe Installation Setup: Task 1A - Configuring the Host 32 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 31
defined in VPS print software: DEST=VPSIMLU1, LUNAME=IMLU1, *LUNAME=SNA047, QBUFSIZE=23476 *ALOGMODE=VPSLU1, *ALOGMODE=VPSCOL, *SEPINFO=HPL The asterisk (*) denotes fields that are not required, and therefore have been commented out. Mainframe Installation Setup: Task 1A - Configuring the Host 33 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 32
, LSPRI=NO, RETRIES=(1,1,3),ISTATUS=ACTIVE,MAXPU=1, OWNER=PCCU1,TYPE=NCP,CALL=IN,ANSWER=ON *CU= NR=1 ACT=13 TRM=YES P1453500PU PUTYPE=(1,2), NPACOLL=YES Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA Server 34 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 33
Sample Configuration number 2 - PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033 , DLOGMOD=SCS1,ISTATUS=ACTIVE LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA Server 35 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 34
to a single printer LU or a display LU group is mapped to a printer LU group. Each group must have the same number of LUs. The example below shows how the VTAM section of the TCP/IP PROFILE data-set can be defined. Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 36 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 35
.36 ENDIPGROUP PRTMAP PRINTERG SPECIP LUMAP SPECLX SPECIP SPECIFIC PRINTERS; specials ; ; ENDVTAM NOTE: If you have multiple printers defined in printmap, you can add multiple IP addresses to the IPGROUP and map the Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 37 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 36
(PRTMAP PRINTERG SPECIP). NOTE: You may also direct a printer device name to the printer IP address using PRTMAP statement as follows: PRTMAP PRT1 xxx.xxx.xxx.xxx (where PRT1 = printer and xxx = printer IP address) Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 38 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 37
Microsoft SNA Server 3.0 Manager is running and that a connection has been selected. To set up a LU printer connection 1 Choose Insert > 3270 > Application LU (LUA). This opens the 3270 LU Properties box. Mainframe Installation Setup: Task 2B - Configuring an SNA Server For TN3270e Printing 39 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 38
to the SNA server. Rightclick the new connection again and choose Properties. 4 Left-click the TN3270 tab. Mark Specific Printer and the IBM- 3287-1 terminal name. 5 Click the |OK| button to finish. Mainframe Installation Setup: Task 2B - Configuring an SNA Server For TN3270e Printing 40 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 39
prints the Standard Network Card menu settings page. b If Network # Setup Page appears, touch it. This prints a settings page for the internal print server in slot #, where # is a number representing the slot in which the print server is installed. Mainframe Installation Setup: Task 3 -Configuring - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 40
Select the print server to be used for SCS printing, for example Standard Network. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. Mainframe Installation Setup: Task 3 -Configuring a Print Server - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 41
can be started. 3 Set the TCP/IP option values shown in the table below. Select Menus > Network/Ports > Standard Network > Std Network Setup > TCP/IP. You will need to contact your network administrator for several of the values. Mainframe Installation Setup: Task 3 -Configuring a Print Server 43 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 42
a BOOTP server. Off, if you set the IP address another way. Enable Auto IP On or Off Default is On. This is the recommended setting WINS Server Address Address of your WINS Server DNS Server Address Address of your DNS Server Mainframe Installation Setup: Task 3 -Configuring a Print Server 44 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 43
Value Comments Your preferred defaults Choose between Do Not Restore *, US-Default, or Non-US-Default 2 Scroll to the desired value. Touch Submit to save one of the factory defaults. 3 Exit the menu by touching Home. Mainframe Installation Setup: Task 4 - Configuring the SCS Settings 45 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 44
> MISC SETTINGS > Euro Support. MISC SETTINGS Option Default Value Euro Support (IDB Event 191) No Recommended Value Comments Your preference. Enable with Yes. 2 Scroll to Yes. Touch Submit button to save the setting. Mainframe Installation Setup: Task 4 - Configuring the SCS Settings 46 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 45
and the telnet extended (TN3270e) protocol. A single TN3270e print session can be established with a host. To configure a TN3270e print session 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > SERVER INFO. 2 Configure the SERVER INFO options. Enter or scroll to new - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 46
below shows the factory default settings and recommended settings. The option setting values found in the table are described in section "NETWORK SETUP> SERVER INFO Menu: Options Overview" on page 95. SERVER INFO Option Name / IP Address IP Address Hostname TN Server Port Default Value Recommended - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 47
INFO Option LU Name Default Value [undefined] Device Print Active to Yes. Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Print Active. Scroll to Yes and touch Submit to save. 4 Exit the menu by touching Home. Mainframe Installation Setup: Task 5 - Configuring - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 48
and change the Connect Status from Print Inactive to another status (there are examples of Connect Status messages on page 92. Mainframe users should continue with Task 6A. SNA Server users should continue with Task 6B. Mainframe Installation Setup: Task 5 - Configuring the SCS/TNe Emulation 50 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 49
to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN3270E Connection Status (see page 92) From the Operator Panel: Display the TN3270E Connect Status by selecting Menus > Option Card Menu >SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 50
and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, is active on the host. Mainframe Installation Setup: Task 6A - Verifying the Mainframe Connection 52 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 51
to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN3270E Connection Status (see page 92) From the Operator Panel: Display the TN3270E Connect Status by selecting Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 52
to verify that the relevant LU definition is active on the host. 4 Check to be sure that the printer in question has been defined-and activated-as a client on the SNA server. Consult your SNA manual. Mainframe Installation Setup: Task 6B - Verifying the Mainframe/SNA Server Connection 54 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 53
the installation, it is recommended that you obtain the latest version of the SCS/TNe firmware, Standard Network or MarkNet internal print server firmware from the internet sites listed in "Support" on page 4 AS/400 and iSeries users Task 1 - Configuring the Host Task 2 - Configuring a Print Server - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 54
the Host The host operating system must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. Section "AS/400 and iSeries Software" on page 279 lists host software which supports these protocols. To configure the host check and set the following three - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 55
QAUTOVRT CHGSYSVAL QAUTOVRT ### Where ### is the number of devices. When these values are properly configured, the host will auto configure devices and writers with the information received from the SCS/TNe Emulation. AS/400 and iSeries Installation Setup: Task 1 - Configuring the Host 57 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 56
Network Card menu settings page. b If Network # Setup Page appears, touch it. This prints a settings page for the internal print server in slot #, where # is a number representing the slot in which the print server is installed. AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 57
the print server to be used for SCS printing, for example Standard Network. Locate NPA Mode and scroll to the Auto setting. Touch Submit to save. This setting will ensure that the printer's LAN connection will detect the Card. AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 58
> Network/Ports > Standard Network > Std Network Setup > TCP/IP. You will need to contact your network administrator for several of the values. You will need to contact your network administrator for several of the values. AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 59
. Off, if you set the IP address another way. Enable Auto IP On or Off Default is On. This is the recommended setting WINS Server Address Address of your WINS Server DNS Server Address Address of your DNS Server AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 61 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 60
Task 3 Configuring the SCS Settings Several SCS option values may need to be changed to properly format and print SCS jobs which do not contain formatting commands in the job. The SCS/TNe Emulation comes with European (A4 paper size) factory default settings. The following five settings are usually - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 61
107) Default Value 68 (for A4) Recommended Value Comments 64 (for Letter). 82 (for Legal). Recommended values for users in the USA 4 (Select other settings within MISC SETTINGS) 5 Exit the MISC SETTINGS menu by touching Home. AS/400 and iSeries Installation Setup: Task 3 - Configuring the SCS - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 62
Value Comments 12240 (for Letter). Recommended value for users in (same for Legal). the USA 8 Exit the PAPER SETTINGS menu by touching Back. 9 Change other settings as desired. 10 Exit the menu by touching Home. AS/400 and iSeries Installation Setup: Task 3 - Configuring the SCS Settings 64 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 63
Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > SCS OPTIONS > Euro Support. Default Value No Recommended Value Comments 2 Scroll to Yes. Touch Submit to save the setting. 3 Exit the menu by by touching Home. AS/400 and iSeries Installation Setup: Task 3 - Configuring the SCS Settings - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 64
end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. SCS jobs are printed from a LAN connected AS/400 or iSeries host using TCP/IP and - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 65
table are described in section "CONNECTION # > SERVER # INFO Menu: Options Overview" on page 165. Option Default Value Name / IPaddress # Use IP# Address IP # Address may be defined for the Telnet service. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 67 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 66
not be auto configured. Contact your system administrator if you do not know the library name. Normal Leave this option at its default value to have printer intervention required conditions reported to the host. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 67
to save. 7 Exit the menu by touching Home. 8 To activate the new settings, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and touch Submit. Touch Home to exit the menus. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 68
, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the Connect # Status from Print Inactive to another status (there are examples of Connect # Status messages on page 92. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 70 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 69
TN5250E Connections Status. 2 Check the print menu page to be sure all option values are set as defined by your system administrator. From the Operator Panel: Print a menu page by selecting Menus > Reports > Menu Settings Page. AS/400 and iSeries Installation Setup: Task 5 - Verifying the Host - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 70
to the print server by entering the print server address as the URL. When the print server display appears, click Reports and then Device Setttings. 3 Check the host auto configure settings. See "Task 1 - Configuring the Host" on page 56. AS/400 and iSeries Installation Setup: Task 5 - Verifying - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 71
Job SCS jobs may be canceled at the printer or MFP. Cancel Job only displays when the printer or MFP is processing a print job. Selecting a specific job to cancel is difficult when several small jobs are queued to print from the host. The job being printed may not be the job which is canceled - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 72
Cancel Job 1 Press the Select button on the operator panel while your job is printing 2 The printer will clear the paper path and display a "Stopping" message. 3 In the next menu, press the Select button when the on- screen checkmark is beside the job you want to cancel. There may be only one - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 73
4 The printer will keep you posted on its progress and automatically return to its normal state, which will be BUSY if it is in the process of printing other jobs. Important Configuration Basics: Printer Cancel Job 75 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 74
In the "Print" column, select the job you want to cancel by touching the print job icon. 3 Touch the Delete Selected Job icon. 4 The screen will display a message to indicate that the job is being deleted. 5 The screen will return to the Home display. Important Configuration Basics: MFP Cancel Job - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 75
Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch COMMON SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP There are four options in the COMMON SETUP menu structure: • Disconnect Ses • Reset TN Session • SCS Debug Trace Operations - Common - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 76
: Connect to the print server by entering the print server address as the URL. When the print server display appears, click Reports and choose Device Settings. In the following reference tables, an asterisk (*) indicates the default factory value. Operations - Common Setup: Introduction 78 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 77
Ses. Reset TN Session Do Not Reset, Reset TN Ses. SCS Debug Trace Disable *, PAR Std. Output, PAR Slot# Output, USB Std. Output, USB Slot# Output Reset ALL Def Do Not Reset, Reset All A description of the COMMON SETUP menu items follows. Operations - Common Setup: Menu Options Overview - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 78
printer is powered Off and On or when a Reset TN Ses. is performed. See the Reset TN Session option below. A Disconnect Ses. should be performed before powering Off the printer TNe sessions. The printer must be powered Off and On or a Reset TN Ses. must - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 79
Reset TN Session IMPORTANT: Powering the printer Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP=> Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. This option - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 80
the trace data, the printer will remain Ready and may not complete menu option allows you to enable tracing and choose where the trace data should be sent. Because tracing will decrease printing performance, it should only be enabled when needed by service personnel for troubleshooting and service - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 81
is a number representing the slot in which the optional parallel port card is installed. USB Std. Out Enable the standard USB port for trace data output. slot in which the optional USB card is installed. NOTE: Only the interfaces installed in the printer will be displayed. Optional cards may be - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 82
panel. Restore ALL SCS/TNe emulation option settings to factory defaults. All sessions will be disconnected. All TNe sessions will have to be reconfigured. Other printer emulation settings (PCL, PS, IPDS, etc.) are not reset when this option is selected. Operations - Common Setup: Reset ALL Def 84 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 83
SETUP menu structure and options. Settings under this menu are used when printing from a Mainframe host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TNE3270E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 84
Tree diagram of the TN3270E SETUP menu structure. Operations - TN3270E SETUP: Introduction 86 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 85
do not have an asterisk in the operator panel to indicate the current setting. The Menu Settings page shows the text string "[invalid]" for options set outside their ranges. Invalid will print for installed features which were selected as the option value but have been uninstalled. Select one of - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 86
An Advanced IDB language command line is shown at the end of menu options which may be set by remote configuration. This shows how to remotely set the menu option to the factory default using the Advanced IDB language (cf. "IDB Basics" on page 248 ff.) Operations - TN3270E SETUP: Introduction 88 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 87
menu is a sub-menu directly under the TN3270E SETUP menu. The following table lists menu options found under the NETWORK SETUP menu. NETWORK SETUP Option name Print Active TN3270 Defaults Connect Status SERVER INFO Values No *, Yes Do Not Restore *, Restore Defaults Shows Primary Status Messages - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 88
Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN3270E SETUP: NETWORK SETUP > Print Active 90 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 89
SETUP factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed in the operator panel. Restore the TN3270e NETWORK SETUP menu options to factory - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 90
in the TN3270E SERVER INFO menu has not been configured. One of the following conditions exists and is preventing a session from being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP). 2 NPA Mode = Off. Solution - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 91
SCS/TNe Emulation is attempting to reconnect. All active Telnet sessions have been disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. The SCS/TNe Emulation is contacting the host or SNA Server - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 92
messages Comments Lst Rsp:The server cannot satisfy the request The TN server cannot satisfy the request sent by the SCS/TNe Emulation. It could be a request was made for a specific terminal or printer type is not a printer or the device request for a specific printer. The device name requested - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 93
NETWORK SETUP> SERVER INFO Menu: Options Overview The SERVER INFO menu is a sub-menu under the NETWORK SETUP menu. The following table lists menu options found under the SERVER INFO menu. NETWORK SETUP > SERVER INFO Option name Values Name / IP Address Use IP Address *, Use Hostname IP - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 94
Name / IP Address This Network Setup > Server Info option specifies the kind of address the SCS/TNe Emulation uses to contact the with the IP Address option. Use the hostname specified with the Hostname option. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Name / IP Address 96 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 95
IP Address This Network Setup > Server Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > IP - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 96
Hostname This Network Setup > Server Info option specifies the name used to identify the host to be contacted by the SCS/TNe string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Hostname 98 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 97
While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > TN Server Port 99 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 98
or on the Menu Settings page ( "How to access the Menu Settings Page" on page 78). Check with your system administrator for the correct LU name to use. Option Value [undefined] * Comments Any ASCII text string up to 10 characters. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > LU - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 99
been defined and is available on the host or SNA server. Request an associated printer which is paired with the terminal LU named in the request. Request a generic printer. The LU name is received from the pool of LU names. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Device Type 101 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 100
system administrator to determine the type of signal to select. This Network Setup > Server Info option specifies the type of keep alive signal send keep alive signals. When this setting is selected, the host should be configured to send a keep alive signal. The SCS/TNe Emulation can receive and - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 101
Keep Alive Time This Network Setup > Server Info option specifies the time in seconds that expires between each keep alive signal sent set to None. Option Value 45 * [1..32000] Comments The range is 1 to 32000 seconds. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Keep Alive Time 103 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 102
106) and FF Support (IDB Option 5) (page 108). Sub-menu. See SCS Options > PAPER SETTINGS Menu: Options Overview (page 133) and Left Margin (IDB Option 103) (page 135). A description of each of the SCS OPTIONS menu item follows. Operations - TN3270E SETUP: SCS OPTIONS Menu: Options Overview 104 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 103
When APO is enabled the SCS/TNe Emulation calculates the print area required for printing the document. This is based on page formatting commands 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:2:EXIT Operations - TN3270E SETUP: SCS OPTIONS > COR/APO Sett (IDB Option 122 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 104
SCS Options > MISC SETTINGS Menu: Options Overview The MISC SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options and sub-menus found under the MISC SETTINGS menu. SCS OPTIONS >MISC SETTINGS Option name FF Support (IDB Option 5) Non-Print Char (IDB Option - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 105
Code (IDB Option 169 bit 1) Leadin Sequence (IDB Option 169 bit2) Euro Support (IDB Event 191) BOLD PRINT Values 132 *, range: 1 - 255 6 *, range: 1 - 255 Translation Normal *, Without '&%' No *, Yes Sub-menu. See SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview (page 129) and Bold On - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 106
FF Support (IDB Option 5) This SCS Options > MISC Settings option defines if a form feed and/or Value Always FF * Always LF LF & FF IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 5:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > FF Support (IDB Option 5) 108 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 107
Non-Print Char (IDB Option 3) This SCS Options > MISC Settings option defines the replacement character to substitute for an unprintable - 255 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 3:45:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Non-Print Char (IDB Option 3) 109 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 108
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option values are ASCII characters in the (%)] Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38,37:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CSC Characters ( - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 109
B - ASCII Character Table" on page 282 for a complete list of characters and their values. Option Value : * IDB Value 58 [colon (:)] Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IDB Delimiter (IDB Option 7) 111 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 110
sent when the printer reports a Paper Out, Paper Jam, goes Off-line etc. Option Value Off * On Value Description No IR signals are sent IR signals are sent IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 21:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Use - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 111
be disabled with the +M command. Is disabled after Power On in Host direct print and Local Copy print. It can be enabled with the -M command. All host generated codes are still will not work correctly. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 113 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 112
NL function is still enabled. NOTE: = &% is factory default. + M [m]: If Option 177 = 0, 1 or 2: After this command the auto-NL function is disabled. All host generated control codes are still sent to the printer. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 113
codes can only be sent to the printer with one of the transparent commands. NOTE: The effect of the +M command is reset per job. - M [m]: . Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 177:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 114
Canadian bilingual Canadian French Danish/Norwegian Danish/Norwegian Alternate English, U.K. English, U.S. See note. Finnish/Swedish Finnish/Swedish Alternate French/Azerty 105 International Italian Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 116 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 115
the SCS options are restored to non-US factory defaults, the default value of this option changes to English (UK). See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:1:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 117 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 116
or not blank pages are printed. With this option enabled, pages containing only a CR, NL, LF or FF are skipped. Option Value Do Not Skip * Skip IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 32:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Skip Blank Page - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 117
100) characters per inch. Option Value 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 10 12 15 16 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CPI (IDB Option 100) 119 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 118
> MISC Settings option defines the maximum Option 102) number of characters per line. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:132:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Max Prt Pos (IDB Option 102) 120 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 119
LPI (IDB Option This SCS Options > MISC Settings option defines the number of 105) lines per inch. Option Value 6 * [1..255] IDB Value 6 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPI (IDB Option 105) 121 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 120
Line Spacing (IDB Option 106) This SCS Options > MISC Settings option defines the line spacing. Option Value Single * Double IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 106:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Line Spacing (IDB Option 106) 122 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 121
are restored to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 107:64:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPP (IDB - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 122
> MISC Settings option selects the transpar(IDB Option 167) ency mode. Option Value Intermate * Axis Enable MPI feat IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 167:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Transparency (IDB Option 167) 124 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 123
and their values. Option Value ASCII Value 0 * ASCII Value [1..255] IDB Value 0 1 - 255 Comments Disable the Formatted String Utility. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 168:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Form Strings (IDB Option 168) 125 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 124
No translation from EBCDIC to ASCII is performed. All transparent data is printed, even invalid data, ie data in the range 40H - FEH. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IBM Trn Code (IDB Option 169 bit 1) 126 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 125
transparent lead in characters are used without the pass through sequence. See the CSC Characters (IDB Options 8 & 9) option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Leadin Sequence (IDB Option 169 bit2) 127 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 126
(IDB Event 191) print support. Option Value No * Yes Comments Disable Euro Support. Enable Euro Support. The ASCII character 186d (0xBAh) is converted to the Euro ASCII character 213d (0xD5h) in symbol set 13U. Operations - TN3270E SETUP: MISC SETTINGS > Euro Support (IDB Event 191) 128 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 127
BOLD PRINT menu. SCS OPTIONS > MISC SETTINGS> BOLD PRINT Option name Bold On CR (IDB Option 22 bit 1) Bold On BS (IDB Option 22 bit 2) Bold On Multi BS (IDB Opt. 22 bit 3) Values Yes *, No Yes *, No Yes *, No A description of each BOLD PRINT menu option follows. Operations - TN3270E SETUP: MISC - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 128
option defines Option 22 bit 1) whether or not bold printing is enabled on a carriage return (CR). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On CR (IDB Option 22 bit - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 129
option defines Option 22 bit 2) whether or not bold printing is enabled on a backspace (BS). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On BS (IDB Option 22 bit 2) 131 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 130
Options > MISC Settings > BOLD PRINT option defines whether or not bold printing is enabled on multiple backspaces. Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On Multi - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 131
Portrait *, Landscape, COR Portrait *, Landscape, COR Portrait *, Landscape, COR Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Letter *, A4 , B5, Legal Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 133 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 132
A description of each PAPER SETTINGS menu option follows. Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 134 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 133
. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Left Margin (IDB Option 103) 135 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 134
character width depends on the setting of the CPI (IDB Option 100) option. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:132:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Right Margin (IDB Option 104) 136 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 135
margin. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Top Margin (IDB Option 108) 137 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 136
to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 109:64:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Bottom - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 137
selected in the printer PAPER MENU Paper Source menu. Paper is fed from Tray 1 Paper is fed from Tray 2 Paper is fed from Tray 3 Paper is fed from Tray 4 Paper is fed from Tray 5 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 113:1:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 138
selects the page orien(IDB Option 123) tation for source input tray 1. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 1 Orient (IDB Option 123) 140 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 139
selects the page orien(IDB Option 124) tation for source input tray 2. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 2 Orient (IDB Option 124) 141 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 140
selects the page orien(IDB Option 125) tation for source input tray 3. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 125:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 3 Orient (IDB Option 125) 142 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 141
selects the page orien(IDB Option 126) tation for source input tray 4. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 4 Orient (IDB Option 126) 143 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 142
selects the page orien(IDB Option 127) tation for source input tray 5. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray 5 Orient (IDB Option 127) 144 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 143
activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 144
activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 145
activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 146
activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 147
activated. This paper size is used to determine the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 148
Overview The TEST OPTIONS menu is a sub-menu directly under the TN3270E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS3270 Hex Dump Normal Mode *, Hex Dump-Mode Print 3270 IDB Do Not Print *, Print SCS3270 Defaults Do Not Restore - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 149
tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and -Mode Comments Normal printer operation. Print job as hex characters without executing control codes. Operations - TN3270E SETUP: TEST OPTIONS > SCS3270 Hex - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 150
by technical support representatives. Option Value Do Not Print * Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the operator panel. Print the IDB settings. Advanced IDB language: &%IDB_PRINT_FULL:EXIT Operations - TN3270E SETUP: TEST - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 151
the Non-US factory default settings. Affected option Country Code (IDB Option 2) Bottom Margin (IDB Option 109) LPP (IDB Option 107) Tray1 Paper Size (IDB Option 90) US-Default Non-US-Default English (US) English (UK) 64 66 64 66 Letter A4 Operations - TN3270E SETUP: TEST OPTIONS > SCS3270 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 152
91) Tray3 Paper Size (IDB Option 92) Tray4 Paper Size (IDB Option 93) Tray5 Paper Size (IDB Option 94) FF Support (IDB Option 5) COR/APO Sett (IDB Option 122) US-Default Letter Letter Letter Letter Always FF Yes Non-US-Default A4 A4 A4 A4 Always FF Yes Operations - TN3270E SETUP: TEST OPTIONS - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 153
. Settings under this menu are used when printing from an AS/400 or iSeries host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TN5250E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 154
Tree diagram of the TN5250E SETUP menu structure. Operations - TN5250E SETUP: Introduction 156 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 155
do not have an asterisk in the operator panel to indicate the current setting. The Menu Settings page shows the text string "[invalid]" for options set outside their ranges. Invalid will print for installed features which were selected as the option value but have been uninstalled. Select one of - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 156
for the Advanced IDB language. These show how to remotely set the menu option to the factory default or how to perform the described action (cf. "IDB Basics" on page 248 ff. - and see "Additional TN5250e Printer Commands Using IDB" on page 260 ff.) Operations - TN5250E SETUP: Introduction 158 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 157
Option name Values Print # Active No *, Yes TN5250## Default Do Not Restore *, Restore Defaults Connect # Status Shows Primary Status Messages and Last Response Messages. Refer to Connect # Status (page 162) for a description of each message. SERVER # INFO Sub-menu. See CONNECTION # > SERVER - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 158
Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN5250E SETUP: CONNECTION # > Print # Active 160 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 159
. Restore the TN5250 CONNECTION ## menu options for the current connection to factory default settings. All TN sessions will be disconnected. All TN sessions will be reconnected except for the session with restored factory defaults. Operations - TN5250E SETUP: CONNECTION # > TN5250## Default 161 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 160
been configured. One of the following conditions exists and is preventing a session from being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #). 2 NPA Mode = Off. Solution: Set to Auto. (Path: Menus > Network/Ports - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 161
disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. Session established on system [SYSTEM NAME] A Telnet connection is established and the SCS/TNe Emulation is ready to receive print jobs. The - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 162
Rsp:8929:Vary on or vary off failed Lst Rsp:8930:Message queue does not exist Comments The requested device is not available operator. Check with system operator. An exisisting device configuration was not found and the autoconfiguration of virtual devices SETUP: CONNECTION # > Connect # Status 164 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 163
response messages Lst Rsp:8935:Session rejected Lst Rsp:8936:Security failure on session Lst Rsp:8937:Automatic sign-on rejected Lst Rsp:8940:Automatic config. failed Keep Alive Type None *, Telnet NOP, Timing Mark Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO Menu: Options Overview 165 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 164
characters. Normal *, Offline, No Reply No *, Yes A description of each SERVER # INFO menu option follows. Name / This Connection# > Server# Info option specifies the kind of IPaddress # with the Hostname # option. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Name / IPaddress # 166 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 165
Connection# > Server# Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > IP # Address 167 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 166
. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Hostname # 168 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 167
a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Server # TN Port 169 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 168
Server# Info option specifies the device and writer name associated with the SCS/TNe Emulation on the host. A device and writer will be auto configured with this name if it does not already exist. Option Value [undefined] * Comments Any ASCII text string up to 10 characters. Operations - TN5250E - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 169
session active. The option is normally left at its default setting. The Keep Alive Time setting determines how alive signals. When this setting is selected, the host should be configured to send a keep alive signal. The SCS/TNe Emulation can SETUP: CONNECTION # > SERVER # INFO > Keep Alive Type 171 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 170
smaller than the session's inactivity timeout value defined on the host. This will help minimize network traffic. This Connection# > Server# Info option specifies the time in seconds that expires is 1 to 32000 seconds. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Keep Alive Time 172 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 171
exist on the host. It will not be auto created. The MSGQ # Lib option may be used to set the message queue library. Leave this option at the default if you do not know the message queue name. Option Value QSYSOPR * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 172
Name option. The message queue library must already exist on the host. It will not be auto created. Leave this option at the default if you do not know the library name. Option Value *LIBL * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E SETUP: CONNECTION # > SERVER - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 173
Replies to the host. Option Value Normal * Offline No Reply Comments Use normal IR replies, i.e. send paper jam as paper jam, paper out as paper out etc. Only send IR replies as offline messages without specifying what kind of IR has occurred. Disable the use of IR replies. Operations - TN5250E - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 174
not the SCS/TNe Emulation senses automatically if the host has ended the Writer. This may be necessary due to the host's management of the print queue when more than one job is in the same queue. Option Value No * Yes Comments Do not sense if writer ends. Sense if writer - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 175
Hor/Ver (IDB Option 158) Use Escape *, Use Line feed, Space + Escape, Linefeed + Esc Format Ctrl Sup (IDB Option 177) Enabled *, Disabled Download Font (IDB Option 244) Enabled *, Disabled Euro Support (IDB Option 139) No *, Yes Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 177 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 176
208) and Country Code (IDB Option 2) (page 210). Sub-menu. See SCS OPTIONS > PAPER SETTINGS Menu: Options Overview (page 231) and Left Margin COR (IDB Opt. 78 & 79) (page 232). A description of each SCS OPTIONS menu item follows. Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 178 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 177
be executed if paper tray 2 has been selected. Option Value Disable * Enable IDB Value 0 1 User IDB parameter OFF ON User IDB command: OVLCAL : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: OVLCAL OFF:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 178
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 28:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 180 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 179
/TNe Emulation uses proportional font handling. The individual character width values of the printer's native fonts must correspond to the width value which the host expects the : PRPFNTMOV : Parameter: OFF, ON Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 181 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 180
User IDB language to set factory default: &%IDB_EDIT: PRPFNTMOV OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 118:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 182 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 181
The command is used to compensate for the reduced printable area of the printer. The option makes it possible to print 80 characters on a line using 10 CPI, 96 characters on a line IDB Value 0 1 User IDB parameter OFF ON Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 183 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 182
User IDB command: COMCPI : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: COMCPI OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 128:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 184 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 183
>: Parameter: For HORMOV ESC uses escape sequences; SP uses spaces For VERMOV ESC uses escape sequences; LF uses line feeds User IDB language to set factory default: &%IDB_EDIT: HORMOV ESC: VERMOV ESC:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 185 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 184
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 158:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 186 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 185
ON OFF User IDB command: CTLCODSUP : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: CTLCODSUP ON:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 177:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Format Ctrl Sup (IDB Option 177) 187 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 186
that these fonts will be downloaded to the printer's memory at Power On. The additional fonts are listed in the table below. The fonts marked with a + contain the Euro character. Option Value Disabled Enabled * IDB Value 0 1 User IDB parameter Not supported Not supported Font IBM font no. PCL - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 187
User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 244:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 189 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 188
Euro Support (IDB Option 139) This SCS Options option controls Euro character printing. If the option is set to Yes, the normal code pages are re-mapped to code pages containing the Euro character. This means that the international currency symbol is replaced with the Euro character in the EBCDIC - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 189
parameter OFF ON User IDB command: EURSUP : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: EURSUP OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 139:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Euro Support (IDB Option 139) 191 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 190
in the decimal range: 33 - 126 : * (ASCII character 58 [colon]), any single ASCII character in the decimal range: 33 - 126 A description of each CSC CHARACTERS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > SCS OPTIONS > CSC CHARACTERS - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 191
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in ampersand] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > IDB First - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 192
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB Option 8) 194 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 193
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in percent] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS OPTIONS > IDB Second - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 194
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 9:37:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB Option 9) 196 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 195
58 [colon] User IDB parameter Not supported User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Delimiter (IDB - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 196
PPM Quality Dis (IDB Opt.126) Off *, On, Enable APO COR LSI Reduc (IDB Option 127) 70% *, range: 1 - 100 [%] A description of each COR/APO SETTINGS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 197
Options > COR/APO Settings option defines the page orientation for paper tray 1. The option setting is only used when the APO/COR to set factory default: &%IDB_EDIT: ORTDRW 1 POR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 121:1:EXITz Operations - TN5250E SETUP: SCS - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 198
Options > COR/APO Settings option defines the page orientation for paper tray 2 and above. The option setting is only used when to set factory default: &%IDB_EDIT: ORTDRW 2 POR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:1:EXI Operations - TN5250E SETUP: SCS OPTIONS - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 199
/Computer Output Reduction) works for paper tray 1. With this option it change only can be made manually. It is also possible to SCS/TNe Emulation calculates the print area required for printing the document. If the document SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 1 (IDB Option - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 200
CORDRW 1 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 1 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 1 (IDB Option 123) 202 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 201
/Computer Output Reduction) works for paper tray 2 and above. With orientation change only can be made manually. It is also possible to select SCS/TNe Emulation calculates the print area required for printing the document. If the SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 2 (IDB Option - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 202
CORDRW 2 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 2 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR Action 2 (IDB Option 124) 204 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 203
mode. To print in computer output reduction mode, the print quality must be print job will be printed in Portrait orientation (Text mode). As it will not always be possible to control the print quality of the jobs printed will ignore the print quality parameter and print all print jobs fulfilling the - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 204
IDB command: TXTMOD : Parameter: OFF, ON, APO User IDB language to set factory default: &%IDB_EDIT: TXTMOD OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > PPM Quality Dis (IDB Opt.126) 206 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 205
>: Parameter: 1 - 100 percent of normal line spacing User IDB language to set factory default: &%IDB_EDIT: LINSPRED 70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:70:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > COR LSI Reduc (IDB Option 207 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 206
menu. SCS OPTIONS>MISC SETTINGS Option name Country Code (IDB Option 2) Codepage (IDB Options 240 and 241) Font (IDB Options 242 and 243) CPI (IDB Option 100) Max Print : 1 - 255 6 LPI *, 3 LPI, 4 LPI, 8 LPI, 9 LPI Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS Menu: Options Overview 208 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 207
*, Paper Media, Envelope Med Prtr Setting *, Output Bin 1, Output Bin 2, Output Bin 3 Prtr Setting *, Simplex, Duplex, Duplex (Tumble) ASCII Value 45, any single ASCII character in the decimal range: 0 - 255 A description of each MISC SETTINGS menu option follows. Operations - TN5250E SETUP: SCS - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 208
codes. In country codes other than International country specific characters replace selected characters. Option Value International * USA/Can Ger/Aus 11 12 User IDB parameter 0 1 2 3 4 5 6 7 8 9 10 11 12 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Country Code (IDB Option 2) 210 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 209
User IDB command: DEFCNTCOD : Parameter: 0 - 15 User IDB language to set factory default: &%IDB_EDIT: DEFCNTCOD 0:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Country Code (IDB Option 2) 211 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 210
commonly used by AS/400 and iSeries computers. If Euro Support has been enabled with the Euro Support (IDB Option 139) option, code pages 37, 273, 1 281 26 + 1 282 28 + 1 284 29 + 1 285 41 + 1 297 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 212 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 211
340 Multi 500 * 244 + 1 500 Iceland 871 103 + 3 871 Code pages with Euro support below this line Turkey 1023 255 + 3 1023 USA/Can 1140 116 + 4 1140 Ger/Aus IDB command: DEFCODPAG : Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 213 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 212
Parameter: 37 - 1149 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFCODPAG 500:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 240:244: OPTION 241:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 214 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 213
from the system. Fonts in shaded rows may be loaded into printer memory. See the Download Font (IDB Option 244) option. Option Value (Font ID) 85 87 + 0 87 110 + 0 110 111 + 0 111 112 + 0 112 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 and 243) 215 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 214
+ 0 222 223 + 0 223 230 + 0 230 244 + 0 244 245 + 0 245 252 + 0 252 253 + 0 253 25 + 1 281 34 + 1 290 239 + 2 751 27 + 4 1051 29 + 4 1053 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 and 243) 216 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 215
: Parameter: 3 - 2103 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFFNT 11:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 242:11: OPTION 243:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 and 243 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 216
User IDB command: DEFCPI : Parameter: 5, 10, 12, 15, 16 User IDB language to set factory default: &%IDB_EDIT: DEFCPI 10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > CPI (IDB Option 100) 218 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 217
User IDB command: DEFMPP : Parameter: 1 - 254 User IDB language to set factory default: &%IDB_EDIT: DEFMPP 80:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:80:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Max Print Pos (IDB Option 102) 219 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 218
User IDB command: DEFLFTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLFTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Left Margin (IDB Option 103) 220 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 219
User IDB command: DEFRGTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFRGTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Right Margin (IDB Option 104) 221 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 220
4 6 8 9 User IDB command: DEFLPI : Parameter: 3, 4, 6, 8, 9 User IDB language to set factory default: &%IDB_EDIT: DEFLPI 6:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > LPI (IDB Option 105) 222 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 221
User IDB command: DEFLPP : Parameter: 0 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLPP 68:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 107:68:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Lines Per Page (IDB Option 107) 223 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 222
User IDB command: DEFTOPMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFTOPMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Top Margin (IDB Option 108) 224 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 223
option selects the paper source input tray printer. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. User IDB command: DEFSRCDRW : Parameter: DEF, 1, 2, 3, 4, 5, 6, 7, 8 User IDB language to set factory default - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 224
Select Media (SLTMED) command. Option Value Prtr Setting * Paper Media Envelope Med IDB Value 0 1 2 User IDB parameter DEF PAP ENV User IDB command: DEFFRMSEL : Parameter: DEF, PAP, ENV User IDB language to set factory default: &%IDB_EDIT: DEFFRMSEL DEF:EXIT Advanced IDB language to - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 225
115) This SCS Options > Misc Settings option selects the paper output bin. The setting will trigger definitions made by the to set factory default: &%IDB_EDIT: DEFDSTDRW DEF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 115:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 226
Printing (SLTSIMDUP) command. The tumble setting is used for pages connected or bound at the top. NOTE: The Duplex and Duplex (Tumble) settings display only on printers with duplex support IDB language to set factory default: &%IDB_EDIT: DEFSIMDUP DEF:EXIT Operations - TN5250E SETUP: SCS OPTIONS > - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 227
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 116:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Simplex/Duplex (IDB Option 116) 229 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 228
: All EBCDIC characters or a printable ASCII hex value User IDB language to set factory default: &%IDB_EDIT: UNPCHR /2D:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 3:45:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Non-Print Char (IDB Option 3) 230 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 229
& 85) Values 634 *, range: 0 - 2880 0 *, range: 0 - 2880 0 *, range: 0 - 2880 147 *, range: 0 - 2880 16848 *, range: 1 - 65535 11908 *, range: 1 - 65535 A description of each PAPER SETTINGS menu option follows. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS Menu: Options Overview 231 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 230
[0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFCOR I 0.44:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 78:122: OPTION 79:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt. 78 & 232 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 231
calculated like this: 79: 0----.-4----4---0-----×-----1---4---4----0-256 ≈2 78: (0.440 × 1440) - (256 × 2) ≈ 122 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt. 78 & 233 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 232
[0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFCOR I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 80:0: OPTION 81:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 & 234 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 233
are calculated like this: 81: 1-----×-----1---4----4---0-256 ≈5 80: (1 × 1440) - (256 × 5) = 160 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 & 235 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 234
options > Paper Settings option defines the offset to be added to the left margin when printing in Landscape factory default: &%IDB_EDIT: LFTOFFLAN I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 86:0: OPTION 87:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 235
are calculated like this: 87: 1-----×-----1---4----4---0-256 ≈5 86: (1 × 1440) - (256 × 5) = 160 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin Lan (IDB Opt. 86 & 87) 237 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 236
options > Paper Settings option defines the offset to be added to the top margin when printing in Landscape factory default: &%IDB_EDIT: TOPOFFLAN I 0.10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 88:147: OPTION 89:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 237
calculated like this: 89: 0----.-1----0---2-----×-----1---4---4----0-256 ≈0 88: (0.102 × 1440) - (256 × 0) ≈ 147 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin Lan (IDB Opt. 88 & 89) 239 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 238
* Letter Legal Executive Length in cm 29.70 27.94 35.56 26.67 Length in inch. 11.70 11.00 14.00 10.50 Option value 16848 15840 20160 15120 User IDB command: PAGLNG : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 239
with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGLNG I 11.70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 82:208: OPTION multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. 82 & 83) 241 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 240
* Letter Legal Executive Width in cm 21.00 21.59 21.59 18.42 Width in inch. 8.27 8.50 8.50 7.25 Option value 11908 12240 12240 10440 User IDB command: PAGWDT : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 241
with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGWDT I 8.27:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 84:132: OPTION 85: multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Width (IDB Opt.84 & 85) 243 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 242
Overview The TEST OPTIONS menu is a sub-menu directly under the TN5250E SETUP menu. The following table lists menu options found under the TEST OPTIONS menu. Option name Values SCS5250 Hex Dump Normal Mode *, Hex Dump-Mode Print 5250 IDB Do Not Print *, Print SCS5250 Defaults Do Not Restore - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 243
tracing for diagnosing print job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and -Mode Comments Normal printer operation. Print job as hex characters without executing control codes. Operations - TN5250E SETUP: TEST OPTIONS > SCS5250 Hex - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 244
support representatives. Option Value Do Not Print Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the operator panel. Print the IDB settings. User IDB language: &%IDB_PRINT_FULL:EXIT Operations - TN5250E SETUP: TEST OPTIONS > Print - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 245
to Defaults their factory default values. Option Value Do Not Restore * Restore Defaults Comments Do not restore any settings. This performs the same action as if Back had been pressed in the operator panel. Restore to factory default TN5250E SCS option menu settings. Operations - TN5250E SETUP - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 246
description is given in the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. The IDB Languages Both TN3270E and TN5250E users can use the Advanced IDB Language to access and configure/customize the SCS options found in the protocol - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 247
used during initial setup or re-configuration of the printing IDB command line sequences on the printer. This is typically done by embedding the unique IDB commands in a normal text document which is printed like any normal job. Alternatively, you can retrieve the SCS options as an IDB Configuration - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 248
the Control Panel" on page 10 ff. "Operations Reference - TN3270E SETUP" on page 85 and "Operations Reference - TN5250E SETUP" on page 155. The descriptions include the available options and their values. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 260 covers IDB commands - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 249
the configuration data is sent as text to the SCS/TNe Emulation. Rules for configuration data prints out the commands, or prints out error messages, it could be because the characters used for programming (& % E : ...etc) have been corrupted. You must reset the SCS OPTIONS to their factory defaults - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 250
sending the trailer string: EXIT This causes the changed options to be saved. The new option settings are active on the next SCS job. All configuration options must be separated by a colon. Line feed, form feed etc. should be avoided, but are accepted in some cases. IDB Basics: IDB Languages Usage - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 251
37:EXIT Option values Refer to the option descriptions in chapter "Operations Reference TN3270E SETUP" on page 85 and in chapter "Operations Reference - TN5250E SETUP" on page 155. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 260 covers IDB commands which can be embedded - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 252
on a PC screen. After the editing is done, it is possible to save the settings in a file. The resulting IDB Configuration File can then be downloaded to one or more printers containing an SCS/TNe Emulation providing easy, fast, and uniform setups. IDB Basics: IDB Configuration File Management - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 253
Retrieving the IDB Configuration File The IDB settings controlling how SCS jobs print can be retrieved via FTP. is necessary as data is transferred in binary mode. binary 4 Retrieve the IDB configuration file. get tn3270e.idb c:\tn3270e.idb (TN3270E users) get tn5250e.idb c:\tn5250e.idb (TN5250E - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 254
5 End the FTP session. bye IDB Basics: Retrieving the IDB Configuration File 256 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 255
is DOS based and is available on the internet site with manual updates listed in "Support" on page 4. Look for the following files. Protocol File TN3270E P01-xxxx.zip TN5250E P02-xxxx.zip Comments This contains the 3270 IDB configuration file editor program, also known as IDB.exe. This contains - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 256
Storing the IDB Configuration File When the IDB configuration file has been edited it can be downloaded to the SCS/TNe Emulation. The download file name is fixed. Downloading a file with a different name will result in an unreadable printout. No IDB settings will be changed. The procedure below - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 257
4 Store the IDB configuration file. put c:\tn3270e.idb put c:\tn5250e.idb (TN3270E users) (TN5250E users) This stores the file from a PC's root directory. 5 End the FTP session. bye The downloaded IDB settings are active on the next SCS job. IDB Basics: Storing the IDB Configuration File 259 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 258
recognized, i.e. included in the SCS data stream. The commands you may work with fall into three groups: 1 Paper Handling 2 Code Page Handling / Code Page 259 3 Miscellaneous See "IDB Basics" on page 248 ff. for background information on IDB. TN5250e Printer Commands Using IDB: Introduction 260 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 259
Input Data String Syntax The input data string () following some printer commands can contain three parts: Text, decimal numbers, and hexadecimal numbers. Text: Text has to be put in quotation marks. "This is a text" Decimal: Decimal numbers are entered normally. Use - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 260
of 1024 bytes each which are sent to the printer at power On. The events can be used to download a small logo or set the printer to a specific emulation. Power On sequence 1 Power On, events 0, 1 and 2 are triggered. 2 DEFMPP (Max print positions) is selected. 3 DEFCPI (CPI) (option 100) triggers - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 261
> : POWON DEL : Parameter: 1 - 4 Example: POWON 3 "Power initialize 3": POWON DEL 3: Delete command Definition number The rest of this chapter is devoted to a run-through of the commands you can work with. TN5250e Printer Commands Using IDB: Initializing - Power On Initialize 263 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 262
specific input tray. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. Command: SRCDRW -: SRCDRW DEL : Delete command Parameter: 1 - 3 , 4 - 8 Drawer number Example: SRCDRW 1 /1B,"&l1H": SRCDRW - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 263
> : DSTDRW DEL : Delete command Parameter: 1 - 3 Drawer number Example: DSTDRW 2 /1B,"&l2G": DSTDRW DEL 1: PCL command string for setting dest.drawer 2 to bin 1 Delete command string for dest.drawer 1 TN5250e Printer Commands Using IDB: Paper Handling > Destination Drawer 265 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 264
PPM (Page Presentation Media) when printing on paper or envelopes is selected. It can also be Delete command Parameter: PAP ENV Select paper media Select envelope media Example: SLTMED PAP "Paper media": SLTMED DEL ENV: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper / Envelope - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 265
command SPSU (Set Print Setup) when a certain kind of paper feed is selected. The command corresponds to event 64 - 65. Command: SLTPAPFED : SLTPAPFED DEL : Delete command Parameter: CON CUT MAN Select continuous paper feed Select cutsheet feed Select manual feed Example - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 266
Paper Handling > Select Simplex/Duplex Printing This is used when simplex or duplex printing is selected. The command can only be used if the printer supports duplex printing. It is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when simplex or duplex printing is selected. - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 267
of the symbols and signs are not contained in the normal character set of the printer which means that they cannot be used from AS/400 or iSeries. With this command : COD259 : COD259 DEL : Delete command TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 269 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 268
Parameter: BEF AFT Before code page 259 selection After code page 259 selection Example: COD259 BEF "Command": COD259 DEL AFT: TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 270 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 269
when paper tray 2 is selected. The command corresponds to event 55 - 56. Command: OVLDRW : OVLDRW DEL : Delete command Parameter: 1 - 2 Drawer number Example: OVLDRW 1 /1B,"&f3Y",/1B,"&f2X":PCL string for calling macro no. 3 OVLDRW DEL 1: TN5250e Printer Commands - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 270
> Before / After Formfeed Command: BEFAFTFED : BEFAFTFED DEL : Parameter: BEF AFT Example: BEFAFTFED BEF "Command": BEDAFTFED DEF AFT: Delete command Before formfeed After formfeed TN5250e Printer Commands Using IDB: Miscellaneous > Before / After Formfeed 272 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 271
>: BEFPORLAN DEL : Delete command Parameter: POR LAN Before portrait selection Before landscape selection Example: BEFPORLAN POR /1B,"&l0E",/1B,"&a0V": PCL command for setting top margin to 0 and moving print position to line 0 BEFPORLAN DEL LAN: TN5250e Printer Commands Using IDB - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 272
. The command corresponds to event 96 - 97. Command: SUBTIT : SUBTIT DEL : Delete command Parameter: IDB HEX Status printout subtitle Hexdump printout subtitle Example: SUBTIT IDB /0A,/0D,"SCS Printer": SUBTIT HEX "Setup for test 05-18-99": SUBTIT DEL HEX: TN5250e - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 273
to event 79. Command: MOVUPRLIN : MOVUPRLIN DEL: Delete command Example: MOVUPRLIN /1B,"&l0E",/1B,"&a0V":PCL command for setting top margin to 0 and moving print position to line 0 MOVUPRLIN DEL: TN5250e Printer Commands Using IDB: Miscellaneous> Move to Uppermost Line 275 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 274
Warranty included with the printer The limited warranty you received with your printer gives warranty terms and conditions. For warranty information, refer to your printer documentation. Warranty: included with the printer 276 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 275
The SCS/TNe Emulation is an option which is installed in the printer optional firmware connector; the Card also provides IPDS emulation (see separate documentation). With the Card and a Standard Network or a MarkNet internal print server (Ethernet), the printer becomes an IBM AS/400, iSeries, or - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 276
Compatibility IBM Printer Emulations • 3270 SCS: IBM 3287/3812 in LU1 mode • 5250 SCS: IBM 3812-01 Compatible Print Servers • Standard Network for connection to an Ethernet LAN. • MarkNet internal print server (Ethernet) Appendix - Specifications, Requirements, Features: Compatibility 278 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 277
Print Platforms Mainframe Software • IBM Communications Server for OS/390 V2R5 or greater • IBM Communications Server for , or V5R1-R3 or greater. • Application System AS/400 Operating System OS/400 V3R7 with PTFs installed. Appendix - Specifications, Requirements, Features: Print Platforms 279 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 278
Features List: 3270 SCS Features supported are dependent upon host software for selection and use. • SCS (LU1) data stream • 5 bin paper input • EBCDIC character conversion • Text string conversion • IBM and 3rd party ASCII transparency modes • EBCDIC hex-dump Appendix - Specifications, - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 279
data streams • 5 bin paper input and duplex • Computer Output Reduction (COR) / Automatic Page Orienta- tion (APO) • IBM font selection using FGID or CPI • IBM ASCII transparency • Multiple code pages and box drawing • Full OfficeVision/400 support • User Configurable SCS Features • EBCDIC character - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 280
Appendix B - ASCII Character Table Printable The table shows all ASCII printable characters. Characters Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 20 space 32 38 8 56 50 P 80 68 h 104 21 ! 33 39 9 57 51 Q 81 69 i 105 22 " 34 3A : 58 52 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 281
Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 2D - 45 45 E 69 5D ] 93 75 u 117 2E . 46 46 F 70 5E ^ 94 76 v 118 2F / 47 47 G 71 5F _ 95 77 w 119 30 0 48 48 H 72 60 ' 96 78 x 120 31 1 49 49 I 73 61 a 97 79 y 121 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 282
TN3270e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS IDB Dump > Print. Appendix - TN3270e IDB Commands: How to Print an IDB Report 284 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 283
List of Larger numbers indicate higher precedence. Commands Precedence Command Comments 5 HEXDUMP Enter hex-dump mode (small format) 5 HEXDUMP_FULL Enter hex-dump mode (large format) 5 IDB_EDIT Enter IDB edit mode 5 IDB_PRINT Dump IDB (small format) 5 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 284
Precedence Command 2 1 {XY} Comments Double CSC (prints ) Single transparent character Refer to the chapter on Understanding the Control Panel (page 10) if necessary. Appendix - TN3270e IDB Commands: List of Commands 286 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 285
can rotate the printout from portrait to landscape based on menu option settings. The distinction is between control of text, printed on matrix printers with wide platens. The automatic controls can easily be tested by using the "Print Screen" key from the system. The screen dump is usually printed - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 286
that no STO commands are present in the data stream from the system. The STO commands always take priority over the automatic controls of the printer. Details The following points refer to the flowchart in the end of this appen- dix. 1 The calculation of the page format is based on information - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 287
PAGLNG = A4 and PAGWDT = A4 2 If the page format stated in the FCB is within (or equal to) the page size settings of the PAGLNG and PAGWDT option settings, the page size is "valid". In that case the printout will be in landscape provided the page length is smaller than the width, otherwise it will - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 288
• 10 pitch fonts are reduced to 13 pitch (font type stated in font table position no. 51) • 12 pitch fonts are reduced to 15 pitch (font type stated in font table position no. 52) • 15 pitch fonts are reduced to 20 pitch (font type stated in font table position no. 53) • Other pitch sizes are - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 289
system print parameters in the FCB by changing the printer file containing default settings for the device. This is done by either changing the existing system printer file QSYSPRT (CHGPRTF FILE(QSYSPRT)) or creating your own printer file (CRTPRTF). Please consult your AS/400 or iSeries manuals for - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 290
Example: Disable COR and set Portrait as default orientation for drawer 2 only. CORDRW 2 = OFF and ORTDRW 2 = POR Flowchart See next page. Appendix - COR/APO Logic (TN5250e): Flowchart 292 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 291
Page Orientation Logic Flowchart Appendix - COR/APO Logic (TN5250e): Flowchart 293 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 292
IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN5250E SETUP > TEST OPTIONS > Print IDB Dump > Print. Appendix - TN5250e IDB Commands: How to Print an IDB Report 294 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 293
codes Standard handling of format control Enter special transparent mode (X = Option 171, Y = Option 172) Double CSC (prints ) Single or Multibyte transparent character Print status dump Print font list Trig event no. X Refer to the chapter on Understanding the Control Panel (page 10) if - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 294
from the system) to the internal fonts used in the printer. The font table has a limit of 50 fonts + than 50 IBM fonts are made, it will print out a message and a font table status sheet. This status with the PRGFNT command. The PRGFNT DEL command deletes an IBM font defined in the font table. - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 295
159 (Boldface), 163 (Essay Bold), 160 (Essay) and 175 (Document) which may be loaded into printer memory at Power On. The font table is prepared for using these fonts. The fonts are loaded with code page PC-850 (12U) and with font ID D10003, D10155, D10159, D10160, D10163 and D10175. The loading of - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 296
This command corresponds to the advanced IDB language FONT command. Command: PRGFNT : PRGFNT DEL : NOTE: Try to avoid deleting the first 7 fonts listed in the status printout (&%IDB_STATUS), as these fonts represent the substitution font IDs set by the SETSUBFNT - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 297
Parameters: 0-65535 This value indicates the IBM font sent from the system. Note that the IBM font numbers are divided into the groups below. pitch area IBM fonts 10 pitch: 1-65 12 pitch: 66-153 proportional: 154-200 13 pitch: 201-210 15 pitch: 211-239 5 pitch: 240-249 17 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 298
characters and has a maximum length of 255 characters. It has to be programmed the same way as printer command input data. The parameter is optional. No string definition will delete the definition of an existing font. NOTE: Please notice that the SCS/TNe Emulation always sends a character - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 299
SCS/TNe Emulation prepares itself for support for downloaded IBM PS fonts. This ensures correct spacing of downloaded proportional spaced fonts. If a this gives no support for justification, bolding and underlining. When selecting a font, a predefined string (String no. 100) is printed before - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 300
2 The downloaded font 10175 is sent when IBM font ID 160 (Essay) is sent from the system. Font ID 160 is within the "proportional spaced" font area, and font 10175 is expected to be 100% IBM compatible as to the character spacing: PRGFNT 160 P /1B,"(s1p12.72v0s0b202T": 3 Delete all previous font - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 301
Set Substituted Font ID If a font ID sent from the system is not found in the font table, the font is substituted with a similar font defined in a special area of the font table. The first 7 font positions listed in the status printout (&%IDB_STATUS) represent the substitution fonts for the - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 302
font IDs sent from the system in the range 66-153, which are not present in the SCS/TNe Emulation with a specific font ID, are printed with the definition of font 86. Appendix - SCS TN5250eFont Table: Set Substituted Font ID 304 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 303
Edition Notice SCS/TNe Emulation User's Guide Fourth Edition July 2009, Rev 004. The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC. AND KODAK PROVIDE THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 304
Print Services Facility, PSF, System/390, zSeries, and z/OS are trademarks of International Business Machines Corporation in the United States, other countries, or both. Intelligent Printer Lexmark and Lexmark with diamond design, MarkNet and MarkVision are trademarks of Lexmark Guide 306 - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 305
Specifications ...2 Support ...4 Customer Support ...4 Important Configuration Basics ...5 Introduction ...5 What are "IDB Options", "IDB events etc.? ...6 Setup Options vs. Printer Setup Options ...6 Understanding the Control Panel ...8 Introduction ...8 Printer operator panel ...9 MFP Touch Screen - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 306
Print Server ...56 Task 3 - Configuring the SCS Settings ...60 Task 4 - Configuring the SCS/TNe Emulation ...64 Task 5 - Verifying the Host Connection ...69 SCS/TNe Cancel ...71 About Cancel Job ...71 Important! ...71 Printer Cancel Job ...72 MFP Cancel Job ...74 Operations Reference - Common Setup - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 307
Reset ALL Def ...82 Operations Reference - TN3270E SETUP 83 Introduction ...83 NETWORK SETUP Menu: Options Overview ...87 Print Active ...88 TN3270 Defaults ...89 Connect Status ...90 NETWORK SETUP> SERVER INFO Menu SETTINGS Menu: Options Overview 104 FF Support (IDB Option 5) ...106 Non-Print Char - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 308
Paper Size (IDB Option 90) ...143 Tray2 Paper Size (IDB Option 91) ...144 Tray3 Paper Size (IDB Option 92) ...145 Tray4 Paper Size (IDB Option 93) ...146 Tray5 Paper Size (IDB Option 94) ...147 TEST OPTIONS Menu: Options Overview ...148 SCS3270 Hex Dump ...149 Print 3270 IDB ...150 SCS3270 Defaults - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 309
SETUP 153 Introduction ...153 CONNECTION # Menu: Options Overview ...157 Print # Active ...158 TN5250## Default ...159 Connect # Status ...160 CONNECTION # > SERVER # INFO Menu 185 Download Font (IDB Option 244) ...186 Euro Support (IDB Option 139) ...188 SCS OPTIONS > CSC CHARACTERS Menu: Options - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 310
) ...223 Forms Media (IDB Option 114) ...224 Output Bin (IDB Option 115) ...225 Simplex/Duplex (IDB Option 116) ...226 Non-Print Char (IDB Option 3) ...228 SCS OPTIONS > PAPER SETTINGS Menu: Options Overview 229 Left Margin COR (IDB Opt. 78 & 79) ...230 Top Margin COR (IDB Opt. 80 & 81) ...232 Left - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 311
Configuration File ...256 Additional TN5250e Printer Commands Using IDB 258 Introduction ...258 Input Data String Syntax ...259 Initializing - Power On Initialize ...260 Paper Handling > Source Drawer ...262 Paper Handling > Destination Drawer ...263 Paper Handling > Select Paper / Envelope Media - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 312
, Requirements, Features 275 Product Description ...275 Compatibility ...276 Print Platforms ...277 Features List: 3270 SCS ...278 Features List: 5250 SCS ...279 ASCII Character Table ...280 Printable Characters ...280 Special TN3270e IDB Commands ...282 How to Print an IDB Report ...282 List of - Lexmark X464 | SCS/TNe Emulation User's Guide - Page 313
SCS/TNe Emulation User's Guide ...303 Trademarks ...304 ...304 Table of Contents ...305 : 313
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
 |
 |
1
Getting Started:
SCS/TNe in a LAN environment
Card for IPDS and SCS/TNe -
SCS/TNe Emulation User’s Guide
Getting Started
SCS/TNe in a
LAN
environment
Thank you for purchasing the Card for IPDS and SCS/TNe.
The card provides high quality IBM host connectivity print output.
With the appropriate print server and host software, your printer or
Multifunction Product (MFP) becomes an IBM host workstation
printer capable of printing IPDS or SCS documents from an iSeries,
AS/400, or mainframe. For a more detailed product description, see
“Specifications, Requirements, Features” on page 277
.
I
MPORTANT
:
Unless otherwise stated, the term
printer in this manual refers to both printers and
MFPs.
SCS data is received in a LAN environment using the Telnet
extended protocol. The Card for IPDS and SCS/TNe adds support
for the TN3270E and the TN5250E protocols. A correctly configured
printer can receive, process, and print SCS print jobs received over
TCP/IP.
Documentation
Overview
This document deals only with setting up and using the
SCS/TNe
emulation
in the Card for IPDS and SCS/TNe. It will help you to
understand, use, and change option settings for receiving SNA