Lexmark X466 SCS/TNe Emulation User's Guide
Lexmark X466 Manual
 |
View all Lexmark X466 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark X466 manual content summary:
- Lexmark X466 | SCS/TNe Emulation User's Guide - Page 1
protocol. The Card for IPDS and SCS/TNe adds support for the TN3270E and the TN5250E protocols. A correctly configured printer can receive, process, and print SCS print jobs received over TCP/IP. Documentation Overview This document deals only with setting up and using the SCS/TNe emulation in the - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 2
LAN and for formatting the way SCS jobs are printed. Unless otherwise specified, references to the AS/400 printers and Muiltifunction Products (MFPs) are supported: • Lexmark C734, C736 • Lexmark E460dn, E460dw, E462dtn • Lexmark T650, T652 • Lexmark T654 • Lexmark T656dne • Lexmark W850 • Lexmark - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 3
to an Ethernet LAN (also called STD Net). • MarkNet internal print server (Ethernet). • Lexmark wireless internal print server. If you need to update your Standard Network or MarkNet firmware, refer to "Support" on page 4. For further information on requirements and specifications, see the appendix - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 4
this guide about using the SCS/TNe emulation, refer to the web site below. If you need to update your Standard Network, MarkNet internal print server, or SCS/TNe firmware, go to http://support.lexmark.com. You may also contact your point of purchase or your local Lexmark office. Support: Customer - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 5
Important Configuration Basics Introduction IMPORTANT: Unless otherwise noted, the term printer refers to printers and MFPs, and the term control panel refers to operator panels and touch screens on these types of products. SCS/TNe MENU options settings can be changed and saved in three ways: • - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 6
"IDB Basics" on page 248 for additional information. Note that in most cases, only technical specialists need to understand and use IDBs. Setup Options vs. Printer Setup Options Setup Options Changes to the option settings under the SCS/TNe MENU will only affect the printing of SCS jobs received - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 7
the SCS print job may override the user default settings displayed in the printer operator panel. This guide discusses setting up the SCS/TNe Emulation and changing the SCS/TNe Emulation settings. Printer Setup Options Changes to printer settings under the various printer menus, such as Paper Menu - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 8
. Printers and MFPs differ, so both operator panels on printers and touch screens on MFPs are illustrated here. If you are familiar with the use of the control panel, skip this chapter, but we recommend familiarizing yourself with the contents of "Remote Configuration Using a Browser" on page 24 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 9
Printer operator Access the SCS/TNe Emulation options and settings from the operpanel ator panel SCS/TNe MENU. To reach the menu: Accessing the SCS/TNe menu 1 From a shows the menu or menu group name to which the displayed items belong. Understanding the Operator Panel: Printer operator panel 11 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 10
effect until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "Printer operator panel" on page 11. 2 Use the navigation buttons - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 11
to change the Country Code for TN3270. 1 Navigate to TN3270E SETUP. Press the Select button. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP 2 Navigate to SCS OPTIONS. Press the Select button. TN 3270 SETUP NETWORK SCS OPTIONS TEST OPTIONS Understanding the Operator Panel: Printer operator - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 12
3 Navigate to MISC SETTINGS. Press the Select button. SCS OPTIONS MISC SETTINGS Cor APO Sett TEST OPTIONS 4 Navigate to the Country Code option. Press the Select button. MISC SETTINGS Format Ctrl Sup Country Code Skip Blank Page Understanding the Operator Panel: Printer operator panel 14 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 13
to be factory default. If you want to change the setting, for example to Fin/Swe, use the navigation buttons to move down through the list. When the on-screen checkmark is next to the desired setting. press the Select button Country Code English (US) Fin/Swe Fin/Swe (alt) 6 While the printer is - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 14
SETTINGS Format Ctrl Sup Country Code Skip Blank Page If you want to check the value of a setting, press the Select button again. You will see an asterisk * beside Fin/Swe to show it is the current active setting. Press the Back button changing the setting Operator Panel: Printer operator panel 16 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 15
a Text String The method for changing a text string is actually the same as that for selecting a value, because you select the letters from pre- the characters. To store the new string, press Select after entering all the characters. Understanding the Operator Panel: Printer operator panel 17 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 16
that has a numerical value, you can usually choose between scrolling just as you would to select any value, or using the numerical pad. If the setting has more than one field, navigate as shown in "Changing a Text String" on page 17. Understanding the Operator Panel: Printer operator panel 18 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 17
an option, you will either scroll through the list of values presented ("Selecting a New Value as a Setting" on page 20), enter a number ("Changing a Numerical Setting" on page 22), or enter a text string ("Changing a Text String" on page 21). Understanding the Operator Panel: MFP Touch Screen 19 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 18
in effect until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "MFP Touch Screen" on page 19. 2 For this example, touch SCS - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 19
an option without making changes, touch (Back) and no changes will be saved. 9 While the printer is saving the setting, Submitting Selection will be displayed. Changing a Text String Here is an example. 1 Select Menus > Option Card Menu > SCS/TNe Menu > TN3270e Setup > Network Setup > Server Info - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 20
. 5 Touch Enter (on some MFPs touch Submit) when you have completed the name. The screen returns to the previous menu level. 6 Touch (Submit) to save changes. Changing a Numerical Setting Example: If you select Menus > Option Card Menu > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 21
Some numerical values contain more than one field. For example, Menus > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > IP Address. For these, use the Keyboard as described in "Changing a Text String" on page 21. Understanding the Operator Panel: MFP Touch Screen 23 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 22
attached to a LAN using a Standard Network port or MarkNet internal print server. Remote configuration is especially useful during printer installation to set all of the SCS/TNe options to the values recommended by your system administrator. At a later time, any necessary changes can be made on each - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 23
. How to Use the Browser Interface To access and change SCS/TNe option settings through your browser: 1 Access the printer web page by typing the IP address of its print server as the URL. 2 Select Settings. 3 Select SCS/TNE Settings. 4 Select the TNe Common menu 5 Disconnect all sessions by - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 24
printing, you may need to end and reset the session at the host. 8 Return to SCS/TNe Settings. 9 Select one of the TN3270E or TN5250E menus. 10 All option values which may be changed remotely will be displayed. Change option settings as desired. 11 Select the Submit button at the bottom of the page - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 25
Submit button. If you have entered values in the page without submitting, and decide to start all over again, click Reset Form. The page will then display the values that were current when you opened the particular TN page. Remote Configuration Using A Browser: How to Use the Browser Interface 27 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 26
IPDS and SCS/TNe code from the internet sites listed in "Support" on page 4. Mainframe Direct Users Task 1A - Configuring the Host Task 2A - Configuring a Host For TN3270e Printing Task 3 -Configuring a Print Server Task 4 - Configuring the SCS Settings Task 5 - Configuring the SCS/TNe Emulation - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 27
Mainframe Direct Users SNA Server Users Task 6A - Verifying the Mainframe Connection Task 6B - Verifying the Mainframe/SNA Server Connection Mainframe Installation Setup: Introduction 29 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 28
Task 1A Configuring the Host TIP: How to define an LU-1 printer in VTAM is described in IBM's VTAM documentation. The Mainframe software must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. "Mainframe Software" on page 279 lists versions which support these - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 29
Sample Configuration number 2: PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1),IDBLK=O61,SSCPFM=USSSCS, ISTATUS=ACTIVE, LCPG93 LU LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1A - Configuring the Host 31 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 30
Sample Configuration Number 3: Local Device - Using VTAM LOCAL LU nodes First create a major node in VTAM to define the VTAM LU's (printer or terminal devices) for telnet sessions as follows: TCP VBUILD TYPE=APPL SC0TCP01APPL AUTH=NVPACE, EAS=1, PARSESS=NO, MODETAB=ISTINCLM, SESSLIM=YES - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 31
defined in VPS print software: DEST=VPSIMLU1, LUNAME=IMLU1, *LUNAME=SNA047, QBUFSIZE=23476 *ALOGMODE=VPSLU1, *ALOGMODE=VPSCOL, *SEPINFO=HPL The asterisk (*) denotes fields that are not required, and therefore have been commented out. Mainframe Installation Setup: Task 1A - Configuring the Host 33 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 32
, TRANSFR=20, DUPLEX=FULL,NEWSYNC=NO, CLOCKNG=EXT, NPACOLL=YES, LSPRI=NO, RETRIES=(1,1,3),ISTATUS=ACTIVE,MAXPU=1, OWNER=PCCU1,TYPE=NCP,CALL=IN,ANSWER=ON *CU= NR=1 ACT=13 TRM=YES P1453500PU PUTYPE=(1,2), NPACOLL=YES Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 33
Sample Configuration number 2 - PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1),IDBLK=O61,SSCPFM= LOACADDR=5,MODETAB=MTPRINT, DLOGMOD=SCS,ISTATUS=ACTIVE Mainframe Installation Setup: Task 1B - Configuring the Host for Printing via a SNA Server 35 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 34
a Host For TN3270e Printing TIP: Refer to your system documentation for further details. Refer also to IBM books such as the IBM book OS/390 eNetwork Communications Server V2R5, TCP/IP Implementation Guide, Volume 1: Configuration and Routing (document no. SG24-5227-00). The printer with the SCS - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 35
.36 ENDIPGROUP PRTMAP PRINTERG SPECIP LUMAP SPECLX SPECIP SPECIFIC PRINTERS; specials ; ; ENDVTAM NOTE: If you have multiple printers defined in printmap, you can add multiple IP addresses to the IPGROUP and map the Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 37 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 36
(PRTMAP PRINTERG SPECIP). NOTE: You may also direct a printer device name to the printer IP address using PRTMAP statement as follows: PRTMAP PRT1 xxx.xxx.xxx.xxx (where PRT1 = printer and xxx = printer IP address) Mainframe Installation Setup: Task 2A - Configuring a Host For TN3270e Printing 38 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 37
Server For TN3270e Printing IMPORTANT: The TN3270e components have to be installed in order to be able to configure the LU printer connection on the SNA gateway or router. A number of different vendors provide SNA gateways and routers. The procedure in this section shows how to set up a Microsoft - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 38
connection created in the previous step. Choose Assign To > TN3270 Service on > Name-of-SNAServer to assign the connection to the SNA Printer and the IBM- 3287-1 terminal name. 5 Click the |OK| button to finish. Mainframe Installation Setup: Task 2B - Configuring an SNA Server For TN3270e Printing - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 39
prints the Standard Network Card menu settings page. b If Network # Setup Page appears, touch it. This prints a settings page for the internal print server in slot #, where # is a number representing the slot in which the print server is installed. Mainframe Installation Setup: Task 3 -Configuring - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 40
B. Configuring the Print Server To enable SCS printing, several print server settings may need to be changed. You can make these changes from the printer operator panel. 1 Set NPA Mode to Auto. Select Menus > Network/Ports. Select the print server to be used for SCS printing, for example Standard - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 41
can be started. 3 Set the TCP/IP option values shown in the table below. Select Menus > Network/Ports > Standard Network > Std Network Setup > TCP/IP. You will need to contact your network administrator for several of the values. Mainframe Installation Setup: Task 3 -Configuring a Print Server 43 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 42
a BOOTP server. Off, if you set the IP address another way. Enable Auto IP On or Off Default is On. This is the recommended setting WINS Server Address Address of your WINS Server DNS Server Address Address of your DNS Server Mainframe Installation Setup: Task 3 -Configuring a Print Server 44 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 43
are many other possibilities. TIP: Refer to Operations Reference - TN3270E SETUP: SCS3270 Defaults, page 153 to see the differences in these settings. A. To select Non-US SCS3270 Defaults Factory defaults are US. To change or restore: 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 44
> MISC SETTINGS > Euro Support. MISC SETTINGS Option Default Value Euro Support (IDB Event 191) No Recommended Value Comments Your preference. Enable with Yes. 2 Scroll to Yes. Touch Submit button to save the setting. Mainframe Installation Setup: Task 4 - Configuring the SCS Settings 46 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 45
can be established with a host. To configure a TN3270e print session 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > SERVER INFO. 2 Configure the SERVER INFO options. Enter or scroll to new values and touch Submit to save your settings. The menu will return to the - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 46
below shows the factory default settings and recommended settings. The option setting values found in the table are described in section "NETWORK SETUP> SERVER INFO Menu: Options Overview" on page 95. SERVER INFO Option Name / IP Address IP Address Hostname TN Server Port Default Value Recommended - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 47
if the Keep Alive Type is set to None. 3 Set Print Active to Yes. Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Print Active. Scroll to Yes and touch Submit to save. 4 Exit the menu by touching Home. Mainframe Installation Setup: Task 5 - Configuring the SCS/TNe - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 48
to communicate and change the Connect Status from Print Inactive to another status (there are examples of Connect Status messages on page 92. Mainframe users should continue with Task 6A. SNA Server users should continue with Task 6B. Mainframe Installation Setup: Task 5 - Configuring the SCS/TNe - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 49
> NETWORK SETUP > Connect Status. Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL. When the print server display appears, click Settings and then SCS/TNe Settings. Choose TN3270E Connection Status. 2 Check the print menu page to - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 50
not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. 3 From the main frame host give the following TCP/IP display command: D TCPIP - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 51
> NETWORK SETUP > Connect Status. Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL. When the print server display appears, click Settings and then SCS/TNe Settings. Select TNTN3270E Connection Status. 2 Check the print menu page - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 52
an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 53
of the SCS/TNe firmware, Standard Network or MarkNet internal print server firmware from the internet sites listed in "Support" on page 4 AS/400 and iSeries users Task 1 - Configuring the Host Task 2 - Configuring a Print Server Task 3 - Configuring the SCS Settings Task 4 - Configuring the SCS/TNe - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 54
Host The host operating system must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. Section "AS/400 and iSeries Software" on page 279 lists host software which supports these protocols. To configure the host check and set the following three system values - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 55
Value Controls the automatic configuration of virtual devices. Must be set to an adequate number of devices Sample commands: DSPSYSVAL QAUTOVRT CHGSYSVAL QAUTOVRT ### Where ### is the number of devices. When these values are properly configured, the host will auto configure devices and writers with - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 56
Network Card menu settings page. b If Network # Setup Page appears, touch it. This prints a settings page for the internal print server in slot #, where # is a number representing the slot in which the print server is installed. AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 57
a loss of SCS/TNe print capability. B. Configuring the Print Server To enable SCS printing, several print server settings may need to be changed. You can make these changes from the printer operator panel. 1 Set NPA Mode to Auto. Select Menus > Network/Ports Select the print server to be used for - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 58
settings may cause communication problems. A setting of "0" allows the host SNA server, or SCS/TNe emulation timeout values to control when print jobs from another protocol, interface, server, or host can be started. 3 Set the TCP/IP option values shown in the table below. Select Menus > Network - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 59
. Off, if you set the IP address another way. Enable Auto IP On or Off Default is On. This is the recommended setting WINS Server Address Address of your WINS Server DNS Server Address Address of your DNS Server AS/400 and iSeries Installation Setup: Task 2 - Configuring a Print Server 61 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 60
Task 3 Configuring the SCS Settings Several SCS option values may need to be changed to properly format and print SCS jobs which do not contain formatting commands in the job. The SCS/TNe Emulation comes with European (A4 paper size) factory default settings. The following five settings are usually - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 61
240 and 241) Multi 500 Recommended Value Comments Your preferred code page 3 Still within MISC SETTINGS, locate Lines Per Page. Scroll to the desired Number and touch Submit to save it. Option Lines Per Page (IDB Option 107) Default Value 68 (for A4) Recommended Value Comments 64 (for Letter - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 62
SETTINGS, locate Page Width. Scroll to the desired value and touch Submit to save it. Default Value 11908 (for A4) Recommended Value Comments 12240 (for Letter). Recommended value for users in (same for Legal). the USA 8 Exit the PAPER SETTINGS menu by touching Back. 9 Change other settings as - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 63
> Option Card Menu > SCS/TNe MENU > TN5250E SETUP > SCS OPTIONS > Euro Support. Default Value No Recommended Value Comments 2 Scroll to Yes. Touch Submit to save the setting. 3 Exit the menu by by touching Home. AS/400 and iSeries Installation Setup: Task 3 - Configuring the SCS Settings 65 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 64
> Disconnect Ses. See: Disconnect Ses, page 80. SCS jobs are printed from a LAN connected AS/400 or iSeries host using TCP/IP and the telnet extended (TN5250e) protocol. Up to four TN5250e print sessions can be established with a single or multiple hosts. To configure the SCS/TNe Emulation 1 Select - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 65
. The option setting values found in the table are described in section "CONNECTION # > SERVER # INFO Menu: Options Overview" on page 165. Option Default Value Name / defined for the Telnet service. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 67 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 66
Leave this at the factory default if the host is configured to send a keep alive signal. Choose a different setting to have the SCS/TNe Emulation send a keep alive signal. Your own preference This setting is not used if the Keep Alive Type option (1-3200 seconds) value is set to None (= disabled - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 67
sense the writer has ended after the first SCS job has started to print. If the writer ends before sending an SCS job to the printer, the TN5250e emulation will not be able to sense the writer has ended. 6 Set Print # Active to Yes for each connection you wish to activate. Select Menus > Option - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 68
are set correctly, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the Connect # Status from Print Inactive to another status (there are examples of Connect # Status messages on page 92. AS/400 and iSeries Installation Setup: Task 4 - Configuring the - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 69
the Host Connection Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found through one or more of the following actions: 1 Check the TN5250E Connection Status (see page 162). From the Operator Panel: Display - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 70
) user interface: Connect to the print server by entering the print server address as the URL. When the print server display appears, click Reports and then Device Setttings. 3 Check the host auto configure settings. See "Task 1 - Configuring the Host" on page 56. AS/400 and iSeries Installation - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 71
Job SCS jobs may be canceled at the printer or MFP. Cancel Job only displays when the printer or MFP is processing a print job. Selecting a specific job to cancel is difficult when several small jobs are queued to print from the host. The job being printed may not be the job which is canceled - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 72
Cancel Job 1 Press the Select button on the operator panel while your job is printing 2 The printer will clear the paper path and display a "Stopping" message. 3 In the next menu, press the Select button when the on- screen checkmark is beside the job you want to cancel. There may be only - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 73
4 The printer will keep you posted on its progress and automatically return to its normal state, which will be BUSY if it is in the process of printing other jobs. Important Configuration Basics: Printer Cancel Job 75 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 74
In the "Print" column, select the job you want to cancel by touching the print job icon. 3 Touch the Delete Selected Job icon. 4 The screen will display a message to indicate that the job is being deleted. 5 The screen will return to the Home display. Important Configuration Basics: MFP Cancel Job - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 75
Operations Reference - Common Setup Introduction As indicated in the tree diagram below, the SCS/TNe MENU is divided into three branches. This are four options in the COMMON SETUP menu structure: • Disconnect Ses • Reset TN Session • SCS Debug Trace Operations - Common Setup: Introduction 77 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 76
Settings Page. • Through the http (browser) user interface: Connect to the print server by entering the print server address as the URL. When the print server display appears, click Reports and choose Device Settings. In the following reference tables, an asterisk (*) indicates the default factory - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 77
name Values Disconnect Ses Do Not Disconn., Disconnect Ses. Reset TN Session Do Not Reset, Reset TN Ses. SCS Debug Trace Disable *, PAR Std. Output, PAR Slot# Output, USB Std. Output, USB Slot# Output Reset ALL Def Do Not Reset, Reset All A description of the COMMON SETUP menu items follows - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 78
the same action as if Back had been pressed in the operator panel. Disconnect Ses. Disconnect ALL active TNe sessions. The printer must be powered Off and On or a Reset TN Ses. must be performed before the SCS/TNe Emulation will attempt to contact the host. Operations - Common Setup: Disconnect - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 79
the SCS/TNe emulation and reconnects. Use this option whenever changes have been made to the Network or Server Info settings to disconnect and reconnect using the new settings. Operator panel text Comments Do Not Reset Do not reset any settings. This performs the same action as if Back had been - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 80
computer running a capture program attached to the selected port to receive the trace data, the printer printing performance, it should only be enabled when needed by service personnel for troubleshooting and service. NOTE: If the SCS/TNe Emulation is set recommended to set the Download Font (IDB Option - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 81
trace data output. # is a number representing the slot in which the optional USB card is installed. NOTE: Only the interfaces installed in the printer will be displayed. Optional cards may be added to provide additional ports for output of the debug trace data. Operations - Common Setup: SCS Debug - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 82
in the operator panel. Restore ALL SCS/TNe emulation option settings to factory defaults. All sessions will be disconnected. All TNe sessions will have to be reconfigured. Other printer emulation settings (PCL, PS, IPDS, etc.) are not reset when this option is selected. Operations - Common Setup - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 83
Operations Reference - TN3270E SETUP Introduction This section describes the SCS/TNe Emulation TN3270E SETUP menu structure and options. Settings under this menu are used when printing from a Mainframe host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 84
Tree diagram of the TN3270E SETUP menu structure. Operations - TN3270E SETUP: Introduction 86 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 85
default settings. An asterisk (*) next to a value setting indicates that the setting is currently active. The current setting for each option is listed on the Menu Settings page ("How to access the Menu Settings Page" on page 78). Options using text strings as settings which have not been configured - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 86
An Advanced IDB language command line is shown at the end of menu options which may be set by remote configuration. This shows how to remotely set the menu option to the factory default using the Advanced IDB language (cf. "IDB Basics" on page 248 ff.) Operations - TN3270E SETUP: Introduction 88 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 87
menu options found under the NETWORK SETUP menu. NETWORK SETUP Option name Print Active TN3270 Defaults Connect Status SERVER INFO Values No *, Yes Do Not Restore *, Restore Defaults Shows Primary Status Messages and Last Response Messages. Refer to Connect Status (page 92) for a description of - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 88
Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN3270E SETUP: NETWORK SETUP > Print Active 90 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 89
Setup option restores the TN3270e NETWORK SETUP factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed in the operator panel. Restore the TN3270e - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 90
menu has not been configured. One of the following conditions exists and is preventing a session from being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP). 2 NPA Mode = Off. Solution: Set to Auto. (Path: Menus - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 91
. The device name or resource name requested by the SCS/TNe Emulation is incompatible with the requested device type. Change the device name or device type on the host or check the configuration of the host and of the SCS/TNe Emulation. Operations - TN3270E SETUP: NETWORK SETUP > Connect Status 93 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 92
SCS/TNe Emulation used the CONNECT command in its request for a specific printer. The device name requested is the partner to some terminal. Lst Rsp:Error occured An unknown error when processing the device type or name has occurred. Operations - TN3270E SETUP: NETWORK SETUP > Connect Status 94 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 93
-menu under the NETWORK SETUP menu. The following table lists menu options found under the SERVER INFO menu. NETWORK SETUP > SERVER undefined] *, ASCII name with up to 10 characters Device Type Specific *, Associated, Generic Keep Alive Type Telnet NOP *, None, Timing Mark Keep Alive Time 45 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 94
Name / IP Address This Network Setup > Server Info option specifies the kind of address the SCS/TNe Emulation uses to contact specified with the IP Address option. Use the hostname specified with the Hostname option. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Name / IP Address 96 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 95
IP Address This Network Setup > Server Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > IP - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 96
Hostname This Network Setup > Server Info option specifies the name used to identify the host to be contacted by the SCS/TNe string up to 16 characters. Contact your system administrator for information on the hostname to use. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Hostname 98 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 97
While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > TN Server Port 99 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 98
/TNe Emulation to connect to the host or SNA gateway. This Network Setup > Server Info option specifies the LU name assigned to the SCS/TNe Emulation on the host or SNA gateway. Remember also to check the setting of the Device Type option. If a specific LU name is requested, then the name must - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 99
been defined and is available on the host or SNA server. Request an associated printer which is paired with the terminal LU named in the request. Request a generic printer. The LU name is received from the pool of LU names. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Device Type 101 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 100
: If the Mainframe has difficulty detecting the selected signal type, try changing to another type. Check with your system administrator to determine the type of signal to select. This Network Setup > Server Info option specifies the type of keep alive signal sent to the host or SNA gateway - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 101
OPTIONS. It resides in the host IP profile dataset: SYS1.TCPPARMS(PROFILE). This setting is not used if the Keep Alive Type is set to None. Option Value 45 * [1..32000] Comments The range is 1 to 32000 seconds. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > Keep Alive Time 103 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 102
COR/APO Sett (IDB Option 122) MISC SETTINGS PAPER SETTINGS Values Yes *, No Sub-menu. See SCS Options > MISC SETTINGS Menu: Options Overview (page 106) and FF Support (IDB Option 5) (page 108). Sub-menu. See SCS Options > PAPER SETTINGS Menu: Options Overview (page 133) and Left Margin (IDB Option - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 103
for printing the document. This is based on page formatting commands received from the host. If the document does not fit on a page in portrait orientation, the orientation is changed to landscape. Option Value No Yes * IDB Value 1 2 Advanced IDB language to set factory default: &%IDB_EDIT - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 104
menu. SCS OPTIONS >MISC SETTINGS Option name FF Support (IDB Option 5) Non-Print Char (IDB Option 3) CSC Characters (IDB Options 8 & 9) IDB Delimiter (IDB Option 7) Use IR (IDB Option 21) Format Ctrl Sup (IDB Option 177) Country Code (IDB Option 2) Skip Blank Page (IDB Option 32) CPI (IDB Option - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 105
Normal *, No Translation Normal *, Without '&%' No *, Yes Sub-menu. See SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview (page 129) and Bold On CR (IDB Option 22 bit 1) (page 130). A description of each MISC SETTINGS menu item follows. Operations - TN3270E SETUP: SCS Options > MISC - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 106
when the MPL (Maximum Page Length) or BM (Bottom Margin) is reached in the data stream. Option Value Always FF * Always LF LF & FF IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 5:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > FF Support (IDB Option 5) 108 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 107
Table" on page 282 for a complete list of printable characters and their values. Option Value ASCII Value 45 * ASCII Value [0..255] IDB Value 45 0 - 255 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 3:45:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Non-Print Char (IDB - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 108
the first option and separating the values for the preceding options with commas. Option Value &% * IDB Values 38 [ampersand (&)] 37 [percent (%)] Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38,37:EXIT Operations - TN3270E SETUP: MISC - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 109
in the decimal range 32 - 126. Refer to "Appendix B - ASCII Character Table" on page 282 for a complete list of characters and their values. Option Value : * IDB Value 58 [colon (:)] Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT Operations - TN3270E SETUP: MISC - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 110
enabled, IR signals are sent when the printer reports a Paper Out, Paper Jam, goes Off-line etc. Option Value Off * On Value Description No IR signals are sent IR signals are sent IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 21:0:EXIT Operations - TN3270E SETUP - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 111
disabled with the +M command. Is disabled after Power On in Host direct print and Local Copy print. It can be enabled with the -M command. All host generated codes are still sent. Is diabled after Power On in Host direct print. It can be enabled with the -M command. All host generated - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 112
is still enabled. NOTE: = &% is factory default. + M [m]: If Option 177 = 0, 1 or 2: After this command the auto-NL function is disabled. All host generated control codes are still sent to the printer. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 114 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 113
CSC>+M command is reset per job. - M [m]: After this command, all Host generated control codes are processed and the auto-NL function operates as normal. Refer to "Appendix C - Special TN3270e IDB Commands" on page 284 for more commands. Advanced IDB language to set factory default: &%IDB_EDIT - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 114
Canadian French Danish/Norwegian Danish/Norwegian Alternate English, U.K. English, U.S. See note. Finnish/Swedish Finnish/Swedish Alternate French/Azerty 105 International Italian Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 116 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 115
the SCS options are restored to non-US factory defaults, the default value of this option changes to English (UK). See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:1:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Country Code (IDB Option 2) 117 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 116
32) This SCS Options > MISC Settings option controls whether or not blank pages are printed. With this option enabled, pages containing only a CR, NL, LF or FF are skipped. Option Value Do Not Skip * Skip IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 32:0:EXIT - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 117
This SCS Options > MISC Settings option defines the number of 100) characters per inch. Option Value 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 10 12 15 16 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CPI (IDB Option 100 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 118
(IDB This SCS Options > MISC Settings option defines the maximum Option 102) number of characters per line. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:132:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Max Prt Pos (IDB Option - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 119
LPI (IDB Option This SCS Options > MISC Settings option defines the number of 105) lines per inch. Option Value 6 * [1..255] IDB Value 6 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPI (IDB Option 105) 121 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 120
Line Spacing (IDB Option 106) This SCS Options > MISC Settings option defines the line spacing. Option Value Single * Double IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 106:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Line Spacing (IDB Option 106) 122 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 121
the number of lines per page. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 107:64:EXIT - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 122
This SCS Options > MISC Settings option selects the transpar(IDB Option 167) ency mode. Option Value Intermate * Axis Enable MPI feat IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 167:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Transparency (IDB Option - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 123
B - ASCII Character Table" on page 282 for a complete list of printable characters and their values. Option Value ASCII Value 0 * ASCII Value [1..255] IDB Value 0 1 - 255 Comments Disable the Formatted String Utility. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 168:0:EXIT - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 124
No translation from EBCDIC to ASCII is performed. All transparent data is printed, even invalid data, ie data in the range 40H - FEH. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > IBM Trn Code (IDB Option 169 bit 1) 126 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 125
transparent lead in characters are used without the pass through sequence. See the CSC Characters (IDB Options 8 & 9) option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 169:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Leadin Sequence (IDB Option 169 bit2) 127 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 126
(IDB Event 191) print support. Option Value No * Yes Comments Disable Euro Support. Enable Euro Support. The ASCII character 186d (0xBAh) is converted to the Euro ASCII character 213d (0xD5h) in symbol set 13U. Operations - TN3270E SETUP: MISC SETTINGS > Euro Support (IDB Event 191) 128 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 127
menu. The following table lists menu options found under the BOLD PRINT menu. SCS OPTIONS > MISC SETTINGS> BOLD PRINT Option name Bold On CR (IDB Option 22 bit 1) Bold On BS (IDB Option 22 bit 2) Bold On Multi BS (IDB Opt. 22 bit 3) Values - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 128
CR (IDB This SCS Options > MISC Settings > BOLD PRINT option defines Option 22 bit 1) whether or not bold printing is enabled on a carriage return (CR). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 129
option defines Option 22 bit 2) whether or not bold printing is enabled on a backspace (BS). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Bold On BS (IDB Option 22 bit 2) 131 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 130
(IDB Opt. 22 bit 3) This SCS Options > MISC Settings > BOLD PRINT option defines whether or not bold printing is enabled on multiple backspaces. Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - TN3270E SETUP - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 131
menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options found under the PAPER SETTINGS menu. Option name Left Margin (IDB Option 103) Right Margin (IDB Option 104) Top Margin (IDB Option 108) Bottom Margin (IDB Option 109) Source Input ( - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 132
A description of each PAPER SETTINGS menu option follows. Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 134 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 133
. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Left Margin (IDB Option 103) 135 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 134
. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:132:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Right Margin (IDB Option 104) 136 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 135
the top margin. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Top Margin (IDB Option 108) 137 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 136
non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 109:64:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Bottom Margin - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 137
2 3 4 5 Comments Feed paper from the paper source selected in the printer PAPER MENU Paper Source menu. Paper is fed from Tray 1 Paper is fed from Tray 2 Paper is fed from Tray 3 Paper is fed from Tray 4 Paper is fed from Tray 5 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 113 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 138
Options > Paper Settings option selects the page orien(IDB Option 123) tation for source input tray 1. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 139
Options > Paper Settings option selects the page orien(IDB Option 124) tation for source input tray 2. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 140
Options > Paper Settings option selects the page orien(IDB Option 125) tation for source input tray 3. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 125:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 141
Options > Paper Settings option selects the page orien(IDB Option 126) tation for source input tray 4. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 142
Options > Paper Settings option selects the page orien(IDB Option 127) tation for source input tray 5. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:0:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 143
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 90:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray1 Paper Size (IDB Option 90) 145 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 144
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 91:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray2 Paper Size (IDB Option 91) 146 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 145
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 92:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray3 Paper Size (IDB Option 92) 147 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 146
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 93:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray4 Paper Size (IDB Option 93) 148 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 147
are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 94:2:EXIT Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS > Tray5 Paper Size (IDB Option 94) 149 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 148
the TEST OPTIONS menu. Option name Values SCS3270 Hex Dump Normal Mode *, Hex Dump-Mode Print 3270 IDB Do Not Print *, Print SCS3270 Defaults Do Not Restore *, US-Default, Non-US-Default A description of each TEST OPTIONS menu item follows. Operations - TN3270E SETUP: TEST OPTIONS Menu - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 149
job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means that a hex dump is not produced even though this option is set to Hex Dump - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 150
this report when asked by technical support representatives. Option Value Do Not Print * Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the operator panel. Print the IDB settings. Advanced IDB language: &%IDB_PRINT_FULL:EXIT Operations - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 151
below summarizes the differences between the US and the Non-US factory default settings. Affected option Country Code (IDB Option 2) Bottom Margin (IDB Option 109) LPP (IDB Option 107) Tray1 Paper Size (IDB Option 90) US-Default Non-US-Default English (US) English (UK) 64 66 64 66 Letter A4 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 152
Size (IDB Option 91) Tray3 Paper Size (IDB Option 92) Tray4 Paper Size (IDB Option 93) Tray5 Paper Size (IDB Option 94) FF Support (IDB Option 5) COR/APO Sett (IDB Option 122) US-Default Letter Letter Letter Letter Always FF Yes Non-US-Default A4 A4 A4 A4 Always FF Yes Operations - TN3270E SETUP - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 153
Operations Reference - TN5250E SETUP Introduction This section describes the SCS/TNe Emulation TN5250E SETUP menu structure and options. Settings under this menu are used when printing from an AS/400 or iSeries host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 154
Tree diagram of the TN5250E SETUP menu structure. Operations - TN5250E SETUP: Introduction 156 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 155
default settings. An asterisk (*) next to a value setting indicates that the setting is currently active. The current setting for each option is listed on the Menu Settings page. ("How to access the Menu Settings Page" on page 78) Options using text strings as settings which have not been configured - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 156
which may be set by remote configuration. Following this are two command lines, one for the User IDB language and another for the Advanced IDB language. These show how to remotely set the menu option to the factory default or how to perform the described action (cf. "IDB Basics" on page 248 ff - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 157
The SCS/TNe Emulation supports four concurrent TN5250E sessions. Each session has its own unique set of network settings. These are located in the CONNECTION#1 - CONNECTION#4 menus. The SCS OPTIONS (pp.177 ff) menu settings are common to all four sessions. This means that changes made under the SCS - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 158
SCS/TNe Emulation for TN5250E communication and printing. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 159
TN5250## This Connection# option restores the TN5250E CONNECTION #1, Default #2, #3, or #4 factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 160
been configured. One of the following conditions exists and is preventing a session from being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #). 2 NPA Mode = Off. Solution: Set to Auto. (Path: Menus > Network/Ports - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 161
Connect # Status: Primary status messages Comments Session Disconnected and Halted All active Telnet sessions have been disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. Session - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 162
canceled Lst Rsp:8920:Object partially damaged Lst Rsp:8921:Communication error Lst Rsp:8922:Negative response received Lst Rsp:8923:Start-up record incorrectly of device failed Lst Rsp:8928:Change of device failed Lst Rsp:8929:Vary on or vary off failed Lst Rsp:8930:Message queue does not exist Comments The - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 163
Connect # Status: Last response messages Lst Rsp:8935:Session rejected Lst Rsp:8936:Security 65000 Device # Name [undefined] *, ASCII name with up to 10 characters Keep Alive Type None *, Telnet NOP, Timing Mark Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO Menu: Options Overview - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 164
Connection# > SERVER # INFO Option name Keep Alive Time MSGQ # Name MSGQ # Lib IR # Reply Auto Sense # END Values 45 *, range: 1 - 32000 [seconds] QSYSOPR *, ASCII name with up to 10 characters. *LIBL *, ASCII name with up to 10 characters. Normal *, Offline, No Reply No *, Yes A description of - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 165
Connection# > Server# Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to use. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > IP # Address 167 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 166
Hostname # This Connection# > Server# Info option specifies the name used to identify the host to be contacted by the SCS/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 167
a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Server # TN Port 169 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 168
Server# Info option specifies the device and writer name associated with the SCS/TNe Emulation on the host. A device and writer will be auto configured with this name if it does not already exist. Option Value [undefined] * Comments Any ASCII text string up to 10 characters. Operations - TN5250E - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 169
and INACTTIMO to help determine the Keep Alive Type signal to be used and the Keep Alive Time value to set. Option Value None * Telnet NOP Timing Mark Comments Do not send keep alive signals. When this setting is selected, the host should be configured to send a keep alive signal. The SCS/TNe - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 170
timeout value defined on the host. This will help minimize network traffic. This Connection# > Server# Info option specifies the time in seconds that expires between each keep alive signal sent to the host. The Keep Alive Type setting specifies the type of signal sent to the host. If the Keep Alive - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 171
exist on the host. It will not be auto created. The MSGQ # Lib option may be used to set the message queue library. Leave this option at the default if you do not know the message queue name. Option Value QSYSOPR * Comments Any ASCII text string with up to 10 characters. Operations - TN5250E - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 172
# Lib This Connection# > Server# Info option specifies the message queue library for the message queue specified in the MSGQ # Name option. The message queue library must already exist on the host. It will not be auto created. Leave this option at the default if you do not know the library name - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 173
Replies to the host. Option Value Normal * Offline No Reply Comments Use normal IR replies, i.e. send paper jam as paper jam, paper out as paper out etc. Only send IR replies as offline messages without specifying what kind of IR has occurred. Disable the use of IR replies. Operations - TN5250E - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 174
not the SCS/TNe Emulation senses automatically if the host has ended the Writer. This may be necessary due to the host's management of the print queue when more than one job is in the same queue. Option Value No * Yes Comments Do not sense if writer ends. Sense if writer - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 175
is a sub-menu directly under the TN5250E SETUP menu. One set of TN5250E SCS OPTIONS menu values are saved. All four Esc Format Ctrl Sup (IDB Option 177) Enabled *, Disabled Download Font (IDB Option 244) Enabled *, Disabled Euro Support (IDB Option 139) No *, Yes Operations - TN5250E SETUP: - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 176
COR/APO SETTINGS Menu: Options Overview (page 198) and Def Page Ori 1 (IDB Option 121) (page 199). Sub-menu. See SCS OPTIONS > MISC SETTINGS Menu: Options Overview (page 208) and Country Code (IDB Option 2) (page 210). Sub-menu. See SCS OPTIONS > PAPER SETTINGS Menu: Options Overview (page 231) and - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 177
and OVLDRW command 2 will be executed if paper tray 2 has been selected. Option Value Disable * Enable IDB Value 0 1 User IDB parameter OFF ON User IDB command: OVLCAL : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: OVLCAL OFF:EXIT Operations - TN5250E - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 178
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 28:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 180 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 179
uses proportional font handling. The individual character width values of the printer's native fonts must correspond to the width value which the order to use bold text, underscored text, and to align the right margin. Setting this option to Use enables Proportional Font Move on all fonts. If you - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 180
User IDB language to set factory default: &%IDB_EDIT: PRPFNTMOV OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 118:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 182 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 181
used to compensate for the reduced printable area of the printer. The option makes it possible to print 80 characters on a line using 10 CPI, 96 characters on a line using 12 CPI and 120 characters on a line using 15 CPI. If the option is set to - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 182
User IDB command: COMCPI : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: COMCPI OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 128:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 184 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 183
: Parameter: For HORMOV ESC uses escape sequences; SP uses spaces For VERMOV ESC uses escape sequences; LF uses line feeds User IDB language to set factory default: &%IDB_EDIT: HORMOV ESC: VERMOV ESC:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 185 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 184
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 158:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 186 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 185
double spaced, disabling it will in most cases solve the problem. Option Value Enabled * Disabled IDB Value 0 1 User IDB parameter ON OFF User IDB command: CTLCODSUP : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: CTLCODSUP ON:EXIT Advanced IDB language to - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 186
Option 244) This SCS Options option extends the fonts available to the SCS/ TNe Emulation by loading additional fonts into the printer memory. Enabled means that these fonts will be downloaded to the printer's memory at Power On. The additional fonts are listed in the table below. The fonts marked - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 187
User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 244:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 189 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 188
Euro character printing. If the option is set to Yes, the normal code pages are re-mapped to code pages containing the Euro character. This means that the international currency symbol is replaced with the Euro character in the EBCDIC code pages. Country Normal code pages Re-mapped code pages USA - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 189
in the printer. See the Download Font (IDB Option 244) option on page 188 and the Font (IDB Options 242 and 243) option on page 215. Option Value No * Yes IDB Value 0 1 User IDB parameter OFF ON User IDB command: EURSUP : Parameter: OFF, ON User IDB language to set factory default - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 190
SCS OPTIONS > CSC CHARACTERS Menu: Options Overview The CSC CHARACTERS menu is a sub-menu directly under the SCS OPTIONS menu. The following table lists menu options found under the CSC CHARACTERS menu. SCS OPTIONS > CSC Characters Option name IDB First Char (IDB Option 8) IDB Second Char (IDB - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 191
is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is page 282 for a complete list of characters and their values. Option Value & * IDB Value 38 [ampersand] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 192
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB Option 8) 194 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 193
is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is page 282 for a complete list of characters and their values. Option Value % * IDB Value 37 [percent] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 194
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 9:37:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB Option 9) 196 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 195
" on page 282 for a complete list of characters and their values. Option Value : * IDB Value 58 [colon] User IDB parameter Not supported User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 196
table lists menu options found under the COR/APO SETTINGS menu. SCS Options > COR/APO Settings Option name Values Def Page Ori 1 (IDB Option 121) Portrait *, Prtr Setting, Landscape Def Page Ori 2 (IDB Option 122) Portrait *, Prtr Setting, Landscape COR Action 1 (IDB Option 123) Enable Auto COR - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 197
1 (IDB Option 121) This SCS Options > COR/APO Settings option defines the page orientation for paper tray 1. The option setting is only used when the APO/COR (Automatic Page Orientation / Computer Output Reduction) function is disabled with the COR Action 1 (IDB Option 123) option. Option Value - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 198
Ori 2 (IDB Option 122) This SCS Options > COR/APO Settings option defines the page orientation for paper tray 2 and above. The option setting is only used when the APO/COR (Automatic Page Orientation / Computer Output Reduction) function is disabled with the COR Action 2 (IDB Option 124) option - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 199
SCS Options > COR/APO Settings option defines how the APO/COR function (Automatic Page Orientation/Computer Output Reduction) works for paper tray 1. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 200
OFF APO COR STODIS User IDB command: CORDRW 1 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 1 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 201
SCS Options > COR/APO Settings option defines how the APO/COR function (Automatic Page Orientation/Computer Output Reduction) works for paper tray 2 and above. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 202
OFF APO COR STODIS User IDB command: CORDRW 2 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 2 COR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 203
the APO/COR function will ignore the print quality parameter and print all print jobs fulfilling the requirements in computer output reduction mode. Refer to "Appendix D - COR/APO Logic (TN5250e)" on page 287 Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > PPM Quality Dis (IDB Opt.126 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 204
Observe TEXT parameter in APO as well User IDB command: TXTMOD : Parameter: OFF, ON, APO User IDB language to set factory default: &%IDB_EDIT: TXTMOD OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > COR/APO - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 205
Computer Output Reduction mode. The spacing is normally set to 70% of the normal line spacing (100%). Option Value 70% * [1..100] IDB Value 70 User IDB parameter 70 User IDB command: LINSPRED : Parameter: 1 - 100 percent of normal line spacing User IDB language to set factory default - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 206
menu. SCS OPTIONS>MISC SETTINGS Option name Country Code (IDB Option 2) Codepage (IDB Options 240 and 241) Font (IDB Options 242 and 243) CPI (IDB Option 100) Max Print Pos (IDB Option 102) Left Margin (IDB Option 103) Right Margin (IDB Option 104) LPI (IDB Option 105) Values International - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 207
/Duplex (IDB Option 116) Non-Print Char (IDB Option 3) Values 68 *, range: 1 - 255 1 *, range: 1 - 255 Tray 1 *, Tray 2, Tray 3, Tray 4, Tray 5 Prtr Setting *, Paper Media, Envelope Med Prtr Setting *, Output Bin 1, Output Bin 2, Output Bin 3 Prtr Setting *, Simplex, Duplex, Duplex (Tumble) ASCII - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 208
the character set. Country definition by Country Code was commonly used on System 36 and 38, and applications migrated from these systems. The International country code forms the basis for all country codes. In country codes other than International country specific characters replace selected - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 209
User IDB command: DEFCNTCOD : Parameter: 0 - 15 User IDB language to set factory default: &%IDB_EDIT: DEFCNTCOD 0:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Country Code (IDB Option 2) 211 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 210
240 and 241) This SCS Options > Misc Settings option defines the code page to be used. Country definition by "Code Page" is commonly used by AS/400 and iSeries computers. If Euro Support has been enabled with the Euro Support (IDB Option 139) option, code pages 37, 273, 277, 278, 280, 284, 285 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 211
340 84 + 1 340 Multi 500 * 244 + 1 500 Iceland 871 103 + 3 871 Code pages with Euro support below this line Turkey 1023 255 + 3 1023 USA/Can 1140 116 + 4 1140 Ger/Aus : DEFCODPAG : Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 213 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 212
Parameter: 37 - 1149 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFCODPAG 500:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 240:244: OPTION 241:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 214 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 213
option selects the current font using the Font ID. This option setting is usually overwritten by the first control buffer from the system. Fonts in shaded rows may be loaded into printer memory. See the Download Font (IDB Option 244) option. Option Value (Font ID) Font Name 3 OCR-B 11 Courier - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 214
+ 0 230 244 + 0 244 245 + 0 245 252 + 0 252 253 + 0 253 25 + 1 281 34 + 1 290 239 + 2 751 27 + 4 1051 29 + 4 1053 Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Font (IDB Options 242 and 243) 216 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 215
35 + 8 2103 User IDB command: DEFFNT : Parameter: 3 - 2103 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFFNT 11:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 242:11: OPTION 243:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 216
16 User IDB parameter 5 10 12 15 16 User IDB command: DEFCPI : Parameter: 5, 10, 12, 15, 16 User IDB language to set factory default: &%IDB_EDIT: DEFCPI 10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 217
User IDB command: DEFMPP : Parameter: 1 - 254 User IDB language to set factory default: &%IDB_EDIT: DEFMPP 80:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:80:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Max Print Pos (IDB Option 102) 219 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 218
[1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFLFTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLFTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 103:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 219
[1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFRGTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFRGTMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 104:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 220
3 4 6 8 9 User IDB parameter 3 4 6 8 9 User IDB command: DEFLPI : Parameter: 3, 4, 6, 8, 9 User IDB language to set factory default: &%IDB_EDIT: DEFLPI 6:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 221
User IDB command: DEFLPP : Parameter: 0 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLPP 68:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 107:68:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Lines Per Page (IDB Option 107) 223 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 222
[1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFTOPMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFTOPMRG 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 108:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 223
the internet site with manual updates listed in "Support" on page 4. User IDB command: DEFSRCDRW : Parameter: DEF, 1, 2, 3, 4, 5, 6, 7, 8 User IDB language to set factory default: &%IDB_EDIT: DEFSRCDRW 1:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 113:1:EXIT - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 224
Value Prtr Setting * Paper Media Envelope Med IDB Value 0 1 2 User IDB parameter DEF PAP ENV User IDB command: DEFFRMSEL : Parameter: DEF, PAP, ENV User IDB language to set factory default: &%IDB_EDIT: DEFFRMSEL DEF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 225
Settings option selects the paper output bin. The setting will trigger definitions made by the Destination Drawer (DSTDRW) command. Option Value Prtr Setting User IDB language to set factory default: &%IDB_EDIT: DEFDSTDRW DEF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 115 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 226
as the print setting. The setting will trigger definitions made by the Select Simplex/Duplex Printing (SLTSIMDUP) command. The tumble setting is used for pages connected or bound at the top. NOTE: The Duplex and Duplex (Tumble) settings display only on printers with duplex support. Option Value - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 227
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 116:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Simplex/Duplex (IDB Option 116) 229 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 228
Settings option defines the replacement character to substitute for an unprintable character found in the data stream. The character is printed when the host sends an unprintable character or a character not supported by the SCS/TNe Emulation. Refer to "Appendix B - ASCII Character Table" on page - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 229
(IDB Opt. 88 & 89) Page Length (IDB Opt. 82 & 83) Page Width (IDB Opt.84 & 85) Values 634 *, range: 0 - 2880 0 *, range: 0 - 2880 0 *, range: 0 - 2880 147 *, range: 0 - 2880 16848 *, range: 1 - 65535 11908 *, range: 1 - 65535 A description of each PAPER SETTINGS menu option follows. Operations - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 230
.. 2.009 or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFCOR I 0.44:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 78:122: OPTION 79:2:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 231
: 79: 0----.-4----4---0-----×-----1---4---4----0-256 ≈2 78: (0.440 × 1440) - (256 × 2) ≈ 122 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin COR (IDB Opt. 78 & 233 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 232
in inches [0.00 .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFCOR I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 80:0: OPTION 81:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 233
this: 81: 1-----×-----1---4----4---0-256 ≈5 80: (1 × 1440) - (256 × 5) = 160 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin COR (IDB Opt. 80 & 235 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 234
inches [0.00 .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFLAN I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 86:0: OPTION 87:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 235
this: 87: 1-----×-----1---4----4---0-256 ≈5 86: (1 × 1440) - (256 × 5) = 160 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Left Margin Lan (IDB Opt. 86 & 87) 237 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 236
inches [0.00 .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFLAN I 0.10:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 88:147: OPTION 89:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 237
: 89: 0----.-1----0---2-----×-----1---4---4----0-256 ≈0 88: (0.102 × 1440) - (256 × 0) ≈ 147 NOTE: Inches can be converted to centimeters by multiplying with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Top Margin Lan (IDB Opt. 88 & 89) 239 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 238
29.70 27.94 35.56 26.67 Length in inch. 11.70 11.00 14.00 10.50 Option value 16848 15840 20160 15120 User IDB command: PAGLNG : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. 82 & 83) 240 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 239
[0.00 .. 45.51] or centimeters [0.00 .. 115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGLNG I 11.70:EXIT Advanced IDB language to set factory default: with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Length (IDB Opt. 82 & 83) 241 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 240
Width (IDB Opt.84 & 85) This SCS options > Paper Settings option defines the page width used by the APO/COR (Automatic Page Orientation function/Computer Output Reduction) to calculate page orientation. Option Value (1/1440 inch) IDB Values (Option 84 and 85) User IDB parameter 11908 * [1..65535 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 241
[0.00 .. 45.51] or centimeters [0.00 .. 115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGWDT I 8.27:EXIT Advanced IDB language to set factory default: with 0.3937 inch/cm. Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page Width (IDB Opt.84 & 85) 243 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 242
the TEST OPTIONS menu. Option name Values SCS5250 Hex Dump Normal Mode *, Hex Dump-Mode Print 5250 IDB Do Not Print *, Print SCS5250 Defaults Do Not Restore *, Restore Defaults A description of each TEST OPTIONS menu option follows. Operations - TN5250E SETUP: TEST OPTIONS Menu: Options - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 243
job problems. When hex dump mode is selected, all data sent to the printer is printed in hexadecimal and character representation. Control codes are not executed. The SCS Debug Trace option overrides this option. This means that a hex dump is not produced even though this option is set to Hex Dump - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 244
listing the current IDB settings. Print this report when asked by technical support representatives. Option Value Do Not Print Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed in the operator panel. Print the IDB settings. User IDB language - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 245
the TN5250E SCS OPTIONS settings to Defaults their factory default values. Option Value Do Not Restore * Restore Defaults Comments Do not restore any settings. This performs the same action as if Back had been pressed in the operator panel. Restore to factory default TN5250E SCS option menu - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 246
to change the SCS option settings remotely. Configuration of the IDB settings should only be carried out by authorized technical personal. A complete description is given in the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. The - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 247
during initial setup or re-configuration of the SCS/TNe settings. The IDB languages should not be used to control settings on a job by job basis. An IDB language is used directly from the AS/400, iSeries or Mainframe host by printing IDB command line sequences on the printer. This is typically done - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 248
Other References Sample IDB command strings, which set the options to their default settings, are written after each option description in chapter "Operations Reference - TN3270E SETUP" on page 85 and in chapter "Operations Reference - TN5250E SETUP" on page 155. Detailed references are found in: " - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 249
3 All option settings with syntax or range errors are ignored. If the SCS/TNe Emulation prints out the commands, or prints out error messages, it could be because the characters used for programming (& % E : ...etc) have been corrupted. You must reset the SCS OPTIONS to their factory defaults. IDB - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 250
mode by sending the command: &%IDB_EDIT: and leave configuration mode, by sending the trailer string: EXIT This causes the changed options to be saved. The new option settings are active on the next SCS job. All configuration options must be separated by a colon. Line feed, form feed etc - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 251
Refer to the option descriptions in chapter "Operations Reference TN3270E SETUP" on page 85 and in chapter "Operations Reference - TN5250E SETUP" on page 155. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 260 covers IDB commands which can be embedded in the SCS data stream - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 252
of all IDB options and events are viewed and edited on a PC screen. After the editing is done, it is possible to save the settings in a file. The resulting IDB Configuration File can then be downloaded to one or more printers containing an SCS/TNe Emulation providing easy, fast, and uniform setups - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 253
Retrieving the IDB Configuration File The IDB settings controlling how SCS jobs print can be retrieved via FTP. The name of the file is fixed and cannot be changed. The procedure below uses a Microsoft FTP client. To retrieve the IDB settings file 1 Start a FTP session. ftp 201.1.12.123 (Sample - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 254
5 End the FTP session. bye IDB Basics: Retrieving the IDB Configuration File 256 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 255
is DOS based and is available on the internet site with manual updates listed in "Support" on page 4. Look for the following files. Protocol File TN3270E P01-xxxx.zip TN5250E P02-xxxx.zip Comments This contains the 3270 IDB configuration file editor program, also known as IDB.exe. This contains - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 256
Storing the IDB Configuration File When the IDB configuration file has been edited it can be downloaded to the SCS/TNe Emulation. The download file name is fixed. Downloading a file with a different name will result in an unreadable printout. No IDB settings will be changed. The procedure below - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 257
4 Store the IDB configuration file. put c:\tn3270e.idb put c:\tn5250e.idb (TN3270E users) (TN5250E users) This stores the file from a PC's root directory. 5 End the FTP session. bye The downloaded IDB settings are active on the next SCS job. IDB Basics: Storing the IDB Configuration File 259 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 258
recognized, i.e. included in the SCS data stream. The commands you may work with fall into three groups: 1 Paper Handling 2 Code Page Handling / Code Page 259 3 Miscellaneous See "IDB Basics" on page 248 ff. for background information on IDB. TN5250e Printer Commands Using IDB: Introduction 260 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 259
Input Data String Syntax The input data string () following some printer commands can contain three parts: Text, decimal numbers, and hexadecimal numbers. Text: Text has to be put in quotation marks. "This is a text" Decimal: Decimal numbers are entered normally. Use - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 260
of 1024 bytes each which are sent to the printer at power On. The events can be used to download a small logo or set the printer to a specific emulation. Power On sequence 1 Power On, events 0, 1 and 2 are triggered. 2 DEFMPP (Max print positions) is selected. 3 DEFCPI (CPI) (option 100) triggers - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 261
initialize 3": POWON DEL 3: Delete command Definition number The rest of this chapter is devoted to a run-through of the commands you can work with. TN5250e Printer Commands Using IDB: Initializing - Power On Initialize 263 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 262
in "Support" on page 4. Command: SRCDRW -: SRCDRW DEL : Delete command Parameter: 1 - 3 , 4 - 8 Drawer number Example: SRCDRW 1 /1B,"&l1H": SRCDRW DEL 3: Set PCL command string for drawer 1 Delete command string for drawer 3 TN5250e Printer Commands Using IDB: Paper - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 263
> : DSTDRW DEL : Delete command Parameter: 1 - 3 Drawer number Example: DSTDRW 2 /1B,"&l2G": DSTDRW DEL 1: PCL command string for setting dest.drawer 2 to bin 1 Delete command string for dest.drawer 1 TN5250e Printer Commands Using IDB: Paper Handling > Destination Drawer 265 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 264
This is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when printing on paper or envelopes is selected. It can also be triggered by the DEFFRMSEL command at Power On. See section "Forms Media (IDB Option 114)" on page 226. The command corresponds to event 62 - 63. Command - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 265
command SPSU (Set Print Setup) when a certain kind of paper feed is selected. The command corresponds to event 64 - 65. Command: SLTPAPFED : SLTPAPFED DEL : Delete command Parameter: CON CUT MAN Select continuous paper feed Select cutsheet feed Select manual feed Example - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 266
Paper Handling > Select Simplex/Duplex Printing This is used when simplex or duplex printing is selected. The command can only be used if the printer supports duplex printing. It is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when simplex or duplex printing is selected. - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 267
or iSeries. With this command it is possible to switch to another character set in the printer each time code page 259 is used. This can be used to switch to a symbol character set or a special "symbol font" if it has been downloaded to the printer. It is also possible to select another font in the - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 268
Parameter: BEF AFT Before code page 259 selection After code page 259 selection Example: COD259 BEF "Command": COD259 DEL AFT: TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 270 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 269
immediately before the first printable character. See section "Overlay Call (IDB Option 28)" on page 179. OVLDRW command 1 is executed when paper tray 1 is selected and OVLDRW command 2 is executed when paper tray 2 is selected. The command corresponds to event 55 - 56. Command: OVLDRW - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 270
Formfeed Command: BEFAFTFED : BEFAFTFED DEL : Parameter: BEF AFT Example: BEFAFTFED BEF "Command": BEDAFTFED DEF AFT: Delete command Before formfeed After formfeed TN5250e Printer Commands Using IDB: Miscellaneous > Before / After Formfeed 272 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 271
: POR LAN Before portrait selection Before landscape selection Example: BEFPORLAN POR /1B,"&l0E",/1B,"&a0V": PCL command for setting top margin to 0 and moving print position to line 0 BEFPORLAN DEL LAN: TN5250e Printer Commands Using IDB: Miscellaneous > Before Portrait/Landscape Selection 273 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 272
is used as an extra headline when printing IDB and hex dumps The command is executed on the top of the first page. It may be used for stating specific information on the front page. This could be information describing which IDB profile is used, printer type, or company name. The command corresponds - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 273
if the print position is placed at line 1 and no characters have been printed. The contents of the string could be PCL codes like: • Top margin setting to uppermost a0V":PCL command for setting top margin to 0 and moving print position to line 0 MOVUPRLIN DEL: TN5250e Printer Commands Using IDB: - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 274
Warranty included with the printer The limited warranty you received with your printer gives warranty terms and conditions. For warranty information, refer to your printer documentation. Warranty: included with the printer 276 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 275
Emulation is an option which is installed in the printer optional firmware connector; the Card also provides IPDS emulation (see separate documentation). With the Card and a Standard Network or a MarkNet internal print server (Ethernet), the printer becomes an IBM AS/400, iSeries, or Mainframe host - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 276
Compatibility IBM Printer Emulations • 3270 SCS: IBM 3287/3812 in LU1 mode • 5250 SCS: IBM 3812-01 Compatible Print Servers • Standard Network for connection to an Ethernet LAN. • MarkNet internal print server (Ethernet) Appendix - Specifications, Requirements, Features: Compatibility 278 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 277
Print Platforms Mainframe Software • IBM Communications Server for OS/390 V2R5 or greater tion level 310 or greater • IBM Communications Server for VTAM V4R4 or greater AS/400 and iSeries Software • Application System AS/400 Operating System OS/400 V4R1R5, or V5R1-R3 or greater. • Application - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 278
Features List: 3270 SCS Features supported are dependent upon host software for selection and use. • SCS (LU1) data stream • 5 bin paper input • EBCDIC character conversion • Text string conversion • IBM and 3rd party ASCII transparency modes • EBCDIC hex-dump Appendix - Specifications, - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 279
data streams • 5 bin paper input and duplex • Computer Output Reduction (COR) / Automatic Page Orienta- tion (APO) • IBM font selection using FGID or CPI • IBM ASCII transparency • Multiple code pages and box drawing • Full OfficeVision/400 support • User Configurable SCS Features • EBCDIC character - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 280
20 space 32 38 8 56 50 P 80 68 h 104 21 ! 33 39 9 57 51 Q 81 69 i 105 22 " 34 3A : 58 52 R 82 6A j 6D m 109 26 & 38 3E > 62 56 V 86 6E n 110 27 ' 39 3F ? 63 57 W 87 6F o 111 28 ( 40 40 @ 64 58 X 88 70 p 112 29 ) 41 41 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 281
Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 2D - 45 45 E 69 5D ] 93 75 u 117 2E . 46 46 F 70 5E ^ 94 76 v 118 2F / 47 47 G 71 5F _ 95 77 w 119 30 0 48 48 H 72 60 ' 96 78 x 120 31 1 49 49 I 73 61 a 97 79 y 121 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 282
TN3270e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS IDB Dump > Print. Appendix - TN3270e IDB Commands: How to Print an IDB Report 284 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 283
5 /... Enter Intermate transparent mode 5 = Reserved, active if option 31 = 0 5 +M Suppress format control codes 5 -M Standard handling of format control codes 5 {XY}.... Enter special transparent mode (X = option 171, Y = option 172) 3 {X}YYY[,ZZZ] - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 284
Precedence Command 2 1 {XY} Comments Double CSC (prints ) Single transparent character Refer to the chapter on Understanding the Control Panel (page 10) if necessary. Appendix - TN3270e IDB Commands: List of Commands 286 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 285
which are normally printed on matrix printers with wide platens. The automatic controls can easily be tested by using the "Print Screen" key from the system. The screen dump is usually printed in landscape and compressed if the automatic page orientation (APO) and computer output reduction (COR - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 286
with values set in the PAGLNG and PAGWDT option settings. Refer to section "Page Length (IDB Opt. 82 & 83)" on page 240 and to section "Page Width (IDB Opt.84 & 85)" on page 242, which together specify the maximum valid page size. Example: Use an A4 page format as valid page. Appendix - COR - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 287
stated in the FCB is within (or equal to) the page size settings of the PAGLNG and PAGWDT option settings, the page size is "valid". In that case the printout will be in landscape provided the page length is smaller than the width, otherwise it will be in portrait. In both cases the font selected - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 288
no. 52) • 15 pitch fonts are reduced to 20 pitch (font type stated in font table position no. 53) • Other pitch sizes are compressed to the nearest smaller font. 4 Most program applications normally have a set of standard values for page length, characters per line etc. The user might have few or no - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 289
for the device. On the AS/400 or iSeries it is possible to affect the system print parameters in the FCB by changing the printer file containing default settings for the device. This is done by either changing the existing system printer file QSYSPRT (CHGPRTF FILE(QSYSPRT)) or creating your own - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 290
Example: Disable COR and set Portrait as default orientation for drawer 2 only. CORDRW 2 = OFF and ORTDRW 2 = POR Flowchart See next page. Appendix - COR/APO Logic (TN5250e): Flowchart 292 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 291
Page Orientation Logic Flowchart Appendix - COR/APO Logic (TN5250e): Flowchart 293 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 292
IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN5250E SETUP > TEST OPTIONS > Print IDB Dump > Print. Appendix - TN5250e IDB Commands: How to Print an IDB Report 294 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 293
control codes Standard handling of format control Enter special transparent mode (X = Option 171, Y = Option 172) Double CSC (prints ) Single or Multibyte transparent character Print status dump Print font list Trig event no. X Refer to the chapter on Understanding the Control Panel (page 10 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 294
internal fonts used in the printer. The font table has a limit of 50 fonts + 3 fonts used for COR (Computer Output Reduction). The SCS/TNe Emulation will detect free font table positions. When attempts to program more than 50 IBM fonts are made, it will print out a message and a font table status - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 295
Italic), 159 (Boldface), 163 (Essay Bold), 160 (Essay) and 175 (Document) which may be loaded into printer memory at Power On. The font table is prepared for using these fonts. The fonts are loaded with code page PC-850 (12U) and with font ID D10003, D10155, D10159, D10160, D10163 and D10175. The - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 296
>: PRGFNT DEL : NOTE: Try to avoid deleting the first 7 fonts listed in the status printout (&%IDB_STATUS), as these fonts represent the substitution font IDs set by the SETSUBFNT command. Appendix - SCS TN5250eFont Table: The "Font" Programming Command 298 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 297
Parameters: 0-65535 This value indicates the IBM font sent from the system. Note that the IBM font numbers are divided into the groups below. pitch area IBM fonts 10 pitch: 1-65 12 pitch: 66-153 proportional: 154-200 13 pitch: 201-210 15 pitch: 211-239 5 pitch: 240-249 17 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 298
The spacing determines whether the SCS/TNe Emulation or the printer has to control the spacing when using proportional fonts (Fonts with IBM 154 - 200). The spacing command should only be used when using downloaded proportional fonts with the correct character spacing. N This value is - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 299
spacing is expected. Please note that this gives no support for justification, bolding and underlining. When selecting a font, a predefined string (String no. 100) is printed before . The predefined string contains the symbol set and is normally /1B,"(12U". Examples: 1 The Letter Gothic - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 300
2 The downloaded font 10175 is sent when IBM font ID 160 (Essay) is sent from the system. Font ID 160 is within the "proportional spaced" font area, - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 301
Set Substituted Font ID If a font ID sent from the system is not found in the font table, the font is 4 5 6 2 Command: SETSUBFNT : NOTE: The font number must be a font number already present in the font table. Appendix - SCS TN5250eFont Table: Set Substituted Font ID 303 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 302
font IDs sent from the system in the range 66-153, which are not present in the SCS/TNe Emulation with a specific font ID, are printed with the definition of font 86. Appendix - SCS TN5250eFont Table: Set Substituted Font ID 304 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 303
Guide Fourth Edition July 2009, Rev 004. The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK errors. Changes are periodically made to the information herein; these changes will be incorporated in later editions. Improvements or changes - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 304
Print Services Facility, PSF, System/390, zSeries, and z/OS are trademarks of International Business Machines Corporation in the United States, other countries, or both. Intelligent Printer Lexmark and Lexmark with diamond design, MarkNet and MarkVision are trademarks of Lexmark Guide 306 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 305
Specifications ...2 Support ...4 Customer Support ...4 Important Configuration Basics ...5 Introduction ...5 What are "IDB Options", "IDB events etc.? ...6 Setup Options vs. Printer Setup Options ...6 Understanding the Control Panel ...8 Introduction ...8 Printer operator panel ...9 MFP Touch Screen - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 306
Host ...54 Task 2 - Configuring a Print Server ...56 Task 3 - Configuring the SCS Settings ...60 Task 4 - Configuring the SCS/TNe Emulation ...64 Task 5 - Verifying the Host Connection ...69 SCS/TNe Cancel ...71 About Cancel Job ...71 Important! ...71 Printer Cancel Job ...72 MFP Cancel Job ...74 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 307
Menu: Options Overview ...87 Print Active ...88 TN3270 Defaults ...89 Connect Status ...90 NETWORK SETUP> SERVER INFO Menu: Options Overview 93 Name / IP Address ...94 IP Address ...95 Hostname ...96 TN Server Port ...97 LU Name ...98 Device Type ...99 Keep Alive Type ...100 Keep Alive Time ...101 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 308
bit2) ...125 Euro Support (IDB Event 191) ...126 SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview 127 Bold On CR (IDB Option 22 bit 1) ...128 Bold On BS (IDB Option 22 bit 2) ...129 Bold On Multi BS (IDB Opt. 22 bit 3) ...130 SCS Options > PAPER SETTINGS Menu: Options Overview 131 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 309
: Options Overview ...157 Print # Active ...158 TN5250## Default ...159 Connect # Status ...160 CONNECTION # > SERVER # INFO Menu: Options Overview 163 Name / IPaddress # ...164 IP # Address ...165 Hostname # ...166 Server # TN Port ...167 Device # Name ...168 Keep Alive Type ...169 Keep Alive Time - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 310
116) ...226 Non-Print Char (IDB Option 3) ...228 SCS OPTIONS > PAPER SETTINGS Menu: Options Overview 229 Left Margin COR (IDB Opt. 78 & 79) ...230 Top Margin COR (IDB Opt. 80 & 81) ...232 Left Margin Lan (IDB Opt. 86 & 87) ...234 Top Margin Lan (IDB Opt. 88 & 89) ...236 Page Length (IDB Opt. 82 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 311
- Power On Initialize ...260 Paper Handling > Source Drawer ...262 Paper Handling > Destination Drawer ...263 Paper Handling > Select Paper / Envelope Media 264 Paper Handling > Select Paper Feed ...265 Paper Handling > Select Simplex/Duplex Printing 266 Code Page 259 > Before/After ...267 - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 312
...280 Printable Characters ...280 Special TN3270e IDB Commands ...282 How to Print an IDB Report ...282 List of Commands ...283 COR/APO Logic ( 285 Details ...286 Flowchart ...290 Special TN5250e IDB Commands ...292 How to Print an IDB Report ...292 List of Commands ...293 Managing the SCS TN5250e - Lexmark X466 | SCS/TNe Emulation User's Guide - Page 313
SCS/TNe Emulation User's Guide ...303 Trademarks ...304 ...304 Table of Contents ...305 : 313
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
 |
 |
1
Getting Started:
SCS/TNe in a LAN environment
Card for IPDS and SCS/TNe -
SCS/TNe Emulation User’s Guide
Getting Started
SCS/TNe in a
LAN
environment
Thank you for purchasing the Card for IPDS and SCS/TNe.
The card provides high quality IBM host connectivity print output.
With the appropriate print server and host software, your printer or
Multifunction Product (MFP) becomes an IBM host workstation
printer capable of printing IPDS or SCS documents from an iSeries,
AS/400, or mainframe. For a more detailed product description, see
“Specifications, Requirements, Features” on page 277
.
I
MPORTANT
:
Unless otherwise stated, the term
printer in this manual refers to both printers and
MFPs.
SCS data is received in a LAN environment using the Telnet
extended protocol. The Card for IPDS and SCS/TNe adds support
for the TN3270E and the TN5250E protocols. A correctly configured
printer can receive, process, and print SCS print jobs received over
TCP/IP.
Documentation
Overview
This document deals only with setting up and using the
SCS/TNe
emulation
in the Card for IPDS and SCS/TNe. It will help you to
understand, use, and change option settings for receiving SNA