Lexmark X5650 Network Guide - Page 12

20

In the “Confirm network key” box, type the same WEP key.

21

Select

This is a computer-to-computer (ad hoc) network; wireless access points are not used.

22

Click

OK

twice to close the two open windows.

23

It may take a few minutes for your computer to recognize the new settings. To check on the status of

your network:

a

Right-click the

Wireless Network Connections

icon.

b

Select

View Available Wireless Networks

.

•

If the network is listed but the computer is not connected, select the ad hoc network and then

click

Connect

.

•

If the network does not appear, wait a minute and then click

Refresh network list

.

24

Insert the installation software CD, and follow the directions for wireless installation.

Note:

Do not connect the installation or network cables until instructed to do so by the setup software.

25

When the available networks are displayed, provide the network name and the security information

you created beginning in step 13. The installer will configure the printer for use with your computer.

26

Store a copy of your network name and security information in a safe place for future reference.

In Windows 2000

•

Refer to the documentation that shipped with your wireless network adapter for information on

configuring an ad hoc network with Windows 2000.

For Macintosh users

1

Create a network name.

In Mac OS X version 10.5

a

From the Finder desktop, click

System Preferences

.

b

Click

Network

.

c

Click

AirPort

.

In Mac OS X version 10.4 and earlier

a

From the Finder desktop, click

Go

Applications

.

b

From the Applications folder, double-click

Internet Connect

.

c

From the toolbar, click

AirPort

.

2

From the Network menu, click

Create Network

.

3

Create a name for the ad hoc network, and then click

OK

.

Note:

Store the network name and password in a safe place for future reference.

Adding a printer to an existing ad hoc wireless

network

Note:

The printer can communicate on only one wireless network at a time. Configuring the printer for an

ad hoc wireless network will remove it from any other wireless network, either ad hoc or infrastructure, for

which it is configured.

Using Windows

1

Do one of the following:

•

In Windows Vista, click

.

•

In Windows XP and earlier, click

Start

.

2

Click

All Programs

or

Programs

, and then select the printer program folder from the list.

3

Click

Lexmark Wireless Setup Utility

.

4

Follow the instructions on the Welcome screen.

Using Macintosh

1

From the Finder desktop, double-click the printer folder.

2

Double-click

Lexmark Wireless Setup Assistant

.

3

Follow the instructions on the Welcome screen.

Using WPS (Wi-Fi Protected Setup)

Wi-Fi Protected Setup

(WPS) is a method of configuring devices on a secure wireless network using fewer

steps than in most other methods. The printer supports WPS and can be configured for a wireless access

using WPS. In order to use WPS to configure the printer, the wireless router must support WPS.

Using a WPS-capable router

If your router supports WPS, you can add the printer to your wireless network using the method supported

by your router. Refer to your router documentation for instructions.

Using Windows Vista

For information on using Windows Vista to set up the printer using WPS, refer to the documentation that

came with the operating system.

Note:

Lexmark recommends that you use the installation software on the CD that shipped with the printer

to configure it for wireless access.

Advanced wireless setup

12

Section	Page
Contents	3
Installing the printer on a wireless network	5
Wireless network compatibility	5
Information you will need to set up the printer on a wireless network	5
Granting access to the software during installation	5
Installing the printer on a wireless network	5
Installing the printer on other computers	5
Interpreting the colors of the Wi-Fi indicator light	6
Special wireless installation instructions	6
Assigning a static IP address	6
Changing wireless settings after installation	7
Switching between USB and wireless connections (Windows only)	7
Switching between USB and wireless connections (Macintosh only)	7
For printers with both wireless and Ethernet network options (selected models only)	8
Switching between USB, Ethernet, and wireless connections (Windows only)	8
Switching between USB, Ethernet, and wireless connections (Macintosh only)	9
Advanced wireless setup	11
Creating an ad hoc wireless network	11
Adding a printer to an existing ad hoc wireless network	12
Using WPS (Wi-Fi Protected Setup)	12
Troubleshooting a printer on a wireless network	13
Wireless troubleshooting checklist	13
Printing a network setup page	13
Wireless configuration does not continue after the USB cable is attached	13
Why isn't my printer in this list?	14
Make sure that your computer and printer are connected to the same wireless network	14
Make sure that the computer is not connected to a Virtual Private Network (VPN)	14
Removing and reinstalling the software	14
Cannot print over wireless network	15
Make sure your computer is connected to your wireless access point (wireless router)	15
Move the computer and/or printer closer to the wireless router	15
Move your access point to minimize interference	15
Check whether the printer is on the same wireless network as the computer	15
Check your WEP key or WPA passphrase	16
Disconnect from VPN session	17
Check your advanced security settings	17
Cannot print and there is a firewall on the computer	17
Wi-Fi indicator light is not lit	17
Check power	17
Wi-Fi indicator light is green but the printer does not print (Windows only)	17
Allow the wireless installation to complete	17
Enable the printer	17
Select the wireless printer	17
Select the wireless port	18
Wi-Fi indicator light is blinking orange during installation (Windows only)	18
Make sure the access point is on	18
Move your access point to minimize interference	18
Try adjusting external antennas	18
Move your printer	18
Check security keys	18
Check MAC address	19
Ping the access point to make sure the network is working	19
Run the wireless setup again	19
Wi-Fi indicator light is blinking orange during installation (Macintosh only)	20
Make sure the wireless access point is on	20
Move your wireless access point to minimize interference	20
Try adjusting external antennas	20
Move your printer	20
Check security keys	20
Check the MAC address	20
Ping the access point to make sure the network is working	20
Run the wireless setup again	21
Wi-Fi indicator light is still orange	21
Check network name	21
Check security keys	21
Move your printer	21
Check MAC address	22
Wireless print server not installed	22
Check power	22
“Communication not available” message displays when printing wirelessly	22
Communication with printer lost when connected to Virtual Private Network (VPN)	22
Installing the printer on an Ethernet network (selected models only)	23
Information you will need to set up the printer on an Ethernet network	23
Installing the printer on a wired (Ethernet) network	23
Troubleshooting a printer on an Ethernet network	24
Printer does not appear in the list of printers found on the network	24
Check the Ethernet cable	24
Make sure the printer power is on	24
Make sure that the network is operating properly	24
Make sure the printer has valid network settings	24
Cannot print to the network printer	24
Check the Ethernet cable	24
Make sure the printer power is on	24
Make sure that the network is operating properly	24
Uninstall and reinstall the software	24
Frequently asked questions	25
Where do I find my WEP key or WPA passphrase?	25
What is an SSID?	25
Where do I find my SSID?	25
What is a network?	25
What types of wireless network security are available?	25
How do I find out what type of security my network is using?	26
How are home networks configured?	26
Why do I need an installation cable?	27
How do I attach the installation cable?	27
How are infrastructure and ad hoc networks different?	28
Finding the signal strength	28
How can I improve wireless signal strength?	29
Move the printer closer to the wireless access point/wireless router	29
Remove obstacles between the access point and the printer	29
Remove sources of interference	29
Arrange the network to reduce signal absorption	29
Can I use my printer on a USB and a network connection at the same time?	29
What is a MAC address?	29
How do I find the MAC address?	29
What is an IP address?	30
What is TCP/IP?	30
How do I locate IP addresses?	30
How are IP addresses assigned?	31
What is a key index?	31
Notices	32
Edition notice	32
UNITED STATES GOVERNMENT RIGHTS	32
Trademarks	32
Networking glossary	33

Lexmark X5650 Network Guide - Page 12

Adding a printer to an existing ad hoc wireless, network, Using WPS Wi-Fi Protected Setup - communication not available

Page 12 highlights