Lexmark X860 SCS/TNe Emulation User's Guide
Lexmark X860 Manual
 |
View all Lexmark X860 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark X860 manual content summary:
- Lexmark X860 | SCS/TNe Emulation User's Guide - Page 1
SCS/TNe - SCS/TNe Emulation User's Guide Getting Started SCS/TNe in a LAN environment IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. Thank you for purchasing the Card for IPDS and SCS/TNe. The card provides high quality IBM host connectivity - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 2
and Specifications Supported Products With the appropriate option card installed, the following printers and Muiltifunction Products (MFPs) are supported: • Lexmark C734, C736 • Lexmark E460dn, E460dw, E462dtn • Lexmark T650, T652 • Lexmark T654 • Lexmark T656dne • Lexmark W850 • Lexmark X463de - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 3
IMPORTANT: Unless otherwise stated, the term printer in this manual refers to both printers and MFPs. • Lexmark X466dte, X466dtwe • Lexmark X651de, X652de • Lexmark X654de, X656de • Lexmark X658de • Lexmark X734de, X736de, X738de • Lexmark X860de, X862de, X864de Required LAN Connection To use the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 4
If you cannot find answers in this guide about using the SCS/TNe emulation, refer to the web site below. If you need to update your Standard Network, MarkNet internal print server, or SCS/TNe firmware, go to http://support.lexmark.com. You may also contact your point of purchase or your local - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 5
printer refers to printers and MFPs, and the term control panel refers to operator panels and touch screens on these types of products. SCS/TNe MENU options settings can be changed see "IDB Basics" on page 248 ff. and "Additional TN5250e Printer Commands Using IDB" on page 260 ff). Using IDB in this - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 6
, PostScript™ or PCL™ jobs. The SCS/TNe Emulation user default settings remain in effect until you save new settings or restore the factory defaults by using one of the SCSxxxx Defaults options under MENU/Menus > Option Card Menu > SCS/TNe MENU > TNxxxE STEUP > TEST OPTIONS. xxxx stands for 3270 or - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 7
defaults using the printer menu Restore Default option does not affect the SCS/TNe MENU settings. Settings you choose in the SCS print job may override the user default settings displayed in the printer operator panel. This guide discusses setting up the SCS/TNe Emulation and changing the SCS/TNe - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 8
how how the control panel works. Printers and MFPs differ, so both operator panels on printers and touch screens on MFPs are illustrated here. If you are in: "Installation Setup for Mainframe Users" on page 28 ff. and "Installation Setup for AS/400 and iSeries Users" on page 55 ff. Detailed - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 9
will be active when you select it. 4 When the on-screen checkmark is displayed next to the Option Card Menu, press the Select button . 5 Navigate to SCS/TNe MENU, pressing Select when the on- screen which the displayed items belong. Understanding the Operator Panel: Printer operator panel 11 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 10
. User-selected default settings remain in effect until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "Printer - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 11
to change the Country Code for TN3270. 1 Navigate to TN3270E SETUP. Press the Select button. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP 2 Navigate to SCS OPTIONS. Press the Select button. TN 3270 SETUP NETWORK SCS OPTIONS TEST OPTIONS Understanding the Operator Panel: Printer operator - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 12
3 Navigate to MISC SETTINGS. Press the Select button. SCS OPTIONS MISC SETTINGS Cor APO Sett TEST OPTIONS 4 Navigate to the Country Code option. Press the Select button. MISC SETTINGS Format Ctrl Sup Country Code Skip Blank Page Understanding the Operator Panel: Printer operator panel 14 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 13
and in this example, it just happens to be factory default. If you want to change the setting, for example to Fin/Swe, use the navigation buttons to move down through the Fin/Swe (alt) 6 While the printer is saving the setting, it will display Submitting Selection. Understanding the Operator Panel - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 14
it is the current active setting. Press the Back button changing the setting. in order to leave the screen without 8 If you need to make additional changes within the same menu group - such as MISC SETTINGS, until the screen appears. Understanding the Operator Panel: Printer operator panel 16 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 15
changing a text string is actually the same as that for selecting a value, because you select the letters from pre-programmed lists. What is special is that the value you select consists of several fields. For example, if you select MENU > Option Card the Operator Panel: Printer operator panel 17 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 16
just as you would to select any value, or using the numerical pad. If the setting has more than one field, navigate as shown in "Changing a Text String" on page 17. Understanding the Operator Panel: Printer operator panel 18 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 17
printer is on and the Ready message appears. 2 Touch the key icon (Menus) on the operator panel 3 Touch or to scroll through the main menus displayed on the screen. 4 Touch Option Card enter a number ("Changing a Numerical Setting" on page 22), or enter a text string ("Changing a Text String" on - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 18
. User-selected default settings remain in effect until you save new settings or restore the factory defaults. All saved options become active on the next host session. Selecting a New Value as a Setting To select a new value 1 Navigate to the SCS/TNe MENU as explained in "MFP - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 19
active setting of an option without making changes, touch (Back) and no changes will be saved. 9 While the printer is saving the setting, Submitting Selection will be displayed. Changing a Text String Here is an example. 1 Select Menus > Option Card Menu > SCS/TNe Menu > TN3270e Setup > Network - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 20
to enter the LU Name. 5 Touch Enter (on some MFPs touch Submit) when you have completed the name. The screen returns to the previous menu level. 6 Touch (Submit) to save changes. Changing a Numerical Setting Example: If you select Menus > Option Card Menu > SCS/TNE Menu > TN3270e Setup > Network - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 21
Some numerical values contain more than one field. For example, Menus > SCS/TNE Menu > TN3270e Setup > Network Setup > Server Info > IP Address. For these, use the Keyboard as described in "Changing a Text String" on page 21. Understanding the Operator Panel: MFP Touch Screen 23 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 22
stated, the term printer in this manual refers to both printers and MFPs. The Card for IPDS and SCS/TNe includes an http user interface. You changes can be made on each printer, either from a browser or via the operator panel. How Remote Configuration Works All option values which may be changed - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 23
SCS/TNe session ends and a new SCS/TNe session is established. How to Use the Browser Interface To access and change SCS/TNe option settings through your browser: 1 Access the printer web page by typing the IP address of its print server as the URL. 2 Select Settings. 3 Select SCS/TNE Settings - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 24
the session from the host. If no jobs are printing, you may need to end and reset the session at the host. 8 Return to SCS/TNe Settings. 9 Select one of the TN3270E or TN5250E menus. 10 All option values which may be changed remotely will be displayed. Change option settings as desired. 11 Select - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 25
the page, next to the Submit button. If you have entered values in the page without submitting, and decide to start all over again, click Reset Form. The page will then display the values that were current when you opened the particular TN page. Remote Configuration Using A Browser: How to Use - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 26
you obtain the latest version of the MarkNet internal print server firmware as well as the latest SCS/TNe publications and Card for IPDS and SCS/TNe code from the internet sites listed in "Support" on page 4. Mainframe Direct Users Task 1A - Configuring the Host Task 2A - Configuring a Host For - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 27
Mainframe Direct Users SNA Server Users Task 6A - Verifying the Mainframe Connection Task 6B - Verifying the Mainframe/SNA Server Connection Mainframe Installation Setup: Introduction 29 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 28
described in IBM's VTAM documentation. The Mainframe software must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. "Mainframe Software" on page 279 lists versions which support these protocols. The printer with the SCS/TNe Emulation is defined to the host - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 29
Sample Configuration number 2: PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1),IDBLK=O61,SSCPFM=USSSCS, ISTATUS=ACTIVE,IRETRY=YES,IDNUM=B0008, PASSLIM=7,PUTYPE=2,DISCNT=NO,VPACING=0 LCPG90 LU LOCADDR=2,MODETAB=MT3274P,USSTAB=USB3274B, DLOGMOD=T3274M2 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 30
Sample Configuration Number 3: Local Device - Using VTAM LOCAL LU nodes First create a major node in VTAM to define the VTAM LU's (printer or terminal devices) for telnet sessions as follows: TCP VBUILD TYPE=APPL SC0TCP01APPL AUTH=NVPACE, EAS=1, PARSESS=NO, MODETAB=ISTINCLM, SESSLIM=YES - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 31
member (i.e. IMLU1 listed above) to the host print software being used. The following is an example of a TN printer definition defined in VPS print software: DEST=VPSIMLU1, LUNAME=IMLU1, *LUNAME=SNA047, QBUFSIZE=23476 *ALOGMODE=VPSLU1, *ALOGMODE=VPSCOL, *SEPINFO=HPL The asterisk (*) denotes fields - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 32
for Printing via a SNA Server TIP: How to define an LU-1 printer in VTAM is described in IBM's VTAM documentation. The printer with the SCS/TNe Emulation is defined to the host like a normal LU-1 (SCS) printer. Two sample configurations are shown below. Sample Configuration number 1 Remote Device - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 33
Sample Configuration number 2 - PU/LU definitions in VTAM VBUILD TYPE=SWNET PSWPG9 PU ADDR=C9,MAXDATA=1033,MAXOUT=7, PACING=(1,1),IDBLK=O61,SSCPFM=USSSCS, ISTATUS=ACTIVE,IRETRY=YES,IDNUM=B0008, PASSLIM=7,PUTYPE=2,DISCNT=NO,VPACING=0 LCPG90 LU LOCADDR=2,MODETAB=MT3274P,USSTAB=USB3274B, DLOGMOD= - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 34
details. Refer also to IBM books such as the IBM book OS/390 eNetwork Communications Server V2R5, TCP/IP Implementation Guide, Volume 1: Configuration and Routing (document no. SG24-5227-00). The printer with the SCS/TNe Emulation is defined to the Telnet server in much the same way as a display LU - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 35
ENDPRTGROUP IPGROUP SPECIP 157.184.116.36 ENDIPGROUP PRTMAP PRINTERG SPECIP LUMAP SPECLX SPECIP SPECIFIC PRINTERS; specials ; ; ENDVTAM NOTE: If you have multiple printers defined in printmap, you can add multiple IP addresses to the IPGROUP and map the Mainframe Installation Setup: Task 2A - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 36
group as shown above (PRTMAP PRINTERG SPECIP). NOTE: You may also direct a printer device name to the printer IP address using PRTMAP statement as follows: PRTMAP PRT1 xxx.xxx.xxx.xxx (where PRT1 = printer and xxx = printer IP address) Mainframe Installation Setup: Task 2A - Configuring a Host For - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 37
Configuring an SNA Server For TN3270e Printing IMPORTANT: The TN3270e components have to be installed in order to be able to configure the LU printer connection on the SNA gateway or router. A number of different vendors provide SNA gateways and routers. The procedure in this section shows how to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 38
created in the previous step. Choose Assign To > TN3270 Service on > Name-of-SNAServer to assign the connection to the SNA server. Rightclick the new connection again and choose Properties. 4 Left-click the TN3270 tab. Mark Specific Printer and the IBM- 3287-1 terminal name. 5 Click the |OK - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 39
Emulation can only receive jobs through a single printer server. Moving the selected Network port on the printer. A. To check the installed print server firmware version 1 From a Ready Page appears, touch it. This prints the Standard Network Card menu settings page. b If Network # Setup Page appears - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 40
SCS printing, several print server settings may need to be changed. You can make these changes from the printer operator panel. 1 Set NPA Mode to Auto. Select Menus will ensure that the printer's LAN connection will detect the Card. Mainframe Installation Setup: Task 3 -Configuring a Print Server - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 41
for SCS printing, for example Standard Network. Select Standard Network > Std Network Setup > Network Card > Job Timeout. Scroll down to 0. Touch Submit to save. Option Value Network Job 0 Timeout Description This is the recommended setting and corresponds to "disabled". Other settings may cause - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 42
TCP/IP Option Value Description Address Address available from your network administrator. Netmask Netmask for your network. Contact your network administrator. Gateway Address of the IP gateway. Contact your network administrator. Enable DHCP On or Off On, if you use a DHCP server. Off, if - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 43
may need to be changed to properly format and print SCS jobs that do not contain formatting commands in the job. The following three settings select Non-US SCS3270 Defaults Factory defaults are US. To change or restore: 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 44
Exit the menu by pressing touching Home. C. To enable Euro support 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > SCS OPTIONS > MISC SETTINGS > Euro Support. MISC SETTINGS Option Default Value Euro Support (IDB Event 191) No Recommended Value Comments Your preference. Enable - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 45
not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. SCS jobs are printed from a LAN connected Mainframe using TCP/ IP and the telnet - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 46
system administrator whether you need to specify the specific IP address or the name of the host which the printer will contact to receive SCS jobs. 0.0.0.0 The TNe Server's IP In order is defined for the Telnet service. Mainframe Installation Setup: Task 5 - Configuring the SCS/TNe Emulation 48 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 47
Please note! Some hosts and servers only recognize uppercase LU Names. Specific Check with your system administrator for the correct setting. The device is set to None. 3 Set Print Active to Yes. Select Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Print Active. Scroll - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 48
> Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and touch Submit. Touch Home to exit the menus. Wait approximately one minute. If all values are set correctly, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 49
Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be selecting Menus > Option Card Menu >SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Connect Status. Through the http (browser) user interface: Connect to the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 50
Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. 3 From the main frame host give the following TCP/IP - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 51
Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be selecting Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP > Connect Status. Through the http (browser) user interface: Connect to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 52
power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. Through the http (browser) user printer in question has been defined-and activated-as a client on the SNA server. Consult your SNA manual. - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 53
is recommended that you obtain the latest version of the SCS/TNe firmware, Standard Network or MarkNet internal print server firmware from the internet sites listed in "Support" on page 4 AS/400 and iSeries users Task 1 - Configuring the Host Task 2 - Configuring a Print Server Task 3 - Configuring - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 54
Task 1 Configuring the Host The host operating system must support TCP/IP and extended Telnet protocols to print SCS jobs to a LAN attached printer. Section "AS/400 and iSeries Software" on page 279 lists host software which supports these protocols. To configure the host check and set the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 55
System Value QAUTOVRT Required Value Controls the automatic configuration of virtual devices. Must be set to an adequate number of devices Sample commands: DSPSYSVAL QAUTOVRT CHGSYSVAL QAUTOVRT ### Where ### is the number of devices. When these values are properly configured, the host will auto - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 56
print server or a Standard Network port on the printer. A. To check the installed print server firmware version 1 From a Ready state touch Menus. . a If Network Setup Page appears, touch it. This prints the Standard Network Card menu settings page. b If Network # Setup Page appears, touch it. This - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 57
receive jobs through a single printer server. Moving the selected print server or inserting a new print server may cause a loss of SCS/TNe print capability. B. Configuring the Print Server To enable SCS printing, several print server settings may need to be changed. You can make these changes from - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 58
used for SCS printing, for example Standard Network. Select Standard Network > Std Network Setup > Network Card > Job Timeout. Scroll down to 0. Touch Submit to save. Option Network Job Timeout Value Description "0" This is the recommended setting and corresponds to "disabled". Other settings may - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 59
TCP/IP Option Value Description Address Address available from your network administrator. Netmask Netmask for your network. Contact your network administrator. Gateway Address of the IP gateway. Contact your network administrator. Enable DHCP On or Off On, if you use a DHCP server. Off, if - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 60
values may need to be changed to properly format and print SCS jobs which do not contain formatting commands in the job. The SCS/TNe Emulation set of SCS OPTIONS values. A. To select settings for your specific country 1 Select Menus > Option Card Menu > SCS/TNe MENU >TN5250E SETUP > SCS OPTIONS > - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 61
Lines Per Page (IDB Option 107) Default Value 68 (for A4) Recommended Value Comments 64 (for Letter). 82 (for Legal). Recommended values for users in the USA 4 (Select other settings within MISC SETTINGS) 5 Exit the MISC SETTINGS menu by touching Home. AS/400 and iSeries Installation Setup - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 62
) Option Page Width (IDB Opt.84 & 85) 6 Select Menus > Option Card Menu > SCS/TNe MENU >TN5250E SETUP > SCS OPTIONS > PAPER SETTINGS > (for Letter). Recommended value for users in (same for Legal). the USA 8 Exit the PAPER SETTINGS menu by touching Back. 9 Change other settings as desired. 10 Exit - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 63
(IDB Option 139) B. To enable Euro support 1 Select Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > SCS OPTIONS > Euro Support. Default Value No Recommended Value Comments 2 Scroll to Yes. Touch Submit to save the setting. 3 Exit the menu by by touching Home. AS/400 and - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 64
does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. SCS jobs are printed from a LAN connected AS/400 or iSeries host using TCP - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 65
system administrator whether you need to specify the specific IP address or the name of the host which the printer will contact to receive SCS jobs. The host's IP address In order to be defined for the Telnet service. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 66
be auto configured. Contact your system administrator if you do not know the library name. Normal Leave this option at its default value to have printer intervention required conditions reported to the host. AS/400 and iSeries Installation Setup: Task 4 - Configuring the SCS/TNe Emulation 68 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 67
job to the printer, the TN5250e emulation will not be able to sense the writer has ended. 6 Set Print # Active to Yes for each connection you wish to activate. Select Menus > Option Card select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Reset TN Session. Scroll to Reset TN Ses and - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 68
Wait approximately one minute. If all values are set correctly, this should allow enough time for the SCS/TNe Emulation and host to communicate and change the Connect # Status from Print Inactive to another status (there are examples of Connect # Status messages on page 92. AS/400 and iSeries - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 69
Send a job to the printer for which you want to verify the connection. If the jobs fails to print correctly, the most common problems can be found Menus > Option Card Menu > SCS/TNe MENU > TN5250 SETUP > CONNECTION # SETUP > Connect # Status. Through the http (browser) user interface: Connect to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 70
TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP > Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. Through the http (browser) user interface: Connect to the print server by entering the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 71
SCS/TNe Cancel About Cancel Job SCS jobs may be canceled at the printer or MFP. Cancel Job only displays when the printer or MFP is processing a print job. Selecting a specific job to cancel is difficult when several small jobs are queued to print from the host. The job being printed may not be - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 72
on the operator panel while your job is printing 2 The printer will clear the paper path and display a "Stopping" message. 3 In the next menu, press the Select button when the on- screen checkmark is beside the job you want to cancel. There may be only one Print Job shown, as in the example below - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 73
4 The printer will keep you posted on its progress and automatically return to its normal state, which will be BUSY if it is in the process of printing other jobs. Important Configuration Basics: Printer Cancel Job 75 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 74
MFP Cancel Job 1 While any job is printing, the Cancel Job icon will be displayed on the printer panel. Touch the icon. 2 In the "Print" column, select the job you want to cancel by touching the print job icon. 3 Touch the Delete Selected Job icon. 4 The screen will display a message to indicate - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 75
section describes the COMMON SETUP menu structure and options for the SCS/TNe Emulation From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch COMMON SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP There are four - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 76
How to access the Menu Settings Page • Reset ALL Def You will always be able to see the selected value for each option on the Menu Settings page. • From the Operator Panel: Select Menus > Reports > Menu Settings Page. • Through the http (browser) user interface: Connect to the print server by - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 77
name Values Disconnect Ses Do Not Disconn., Disconnect Ses. Reset TN Session Do Not Reset, Reset TN Ses. SCS Debug Trace Disable *, PAR Std. Output, PAR Slot# Output, USB Std. Output, USB Slot# Output Reset ALL Def Do Not Reset, Reset All A description of the COMMON SETUP menu items follows - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 78
the same action as if Back had been pressed in the operator panel. Disconnect Ses. Disconnect ALL active TNe sessions. The printer must be powered Off and On or a Reset TN Ses. must be performed before the SCS/TNe Emulation will attempt to contact the host. Operations - Common Setup: Disconnect - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 79
Reset TN Session IMPORTANT: Powering the printer Off and On does not end TCP/IP and Telnet sessions in an orderly manner. To power the printer Off properly, select Menus > Option Card Menu > SCS/TNe MENU > COMMON SETUP=> Disconnect Ses > Disconnect Ses. See: Disconnect Ses, page 80. This option - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 80
selected port to receive the trace data, the printer will remain Ready and may not complete establishing be enabled when needed by service personnel for troubleshooting and service. NOTE: If the be output in the trace data before the job is processed. This decreases trace performance significantly. - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 81
in slot # for trace data output. # is a number representing the slot in which the optional USB card is installed. NOTE: Only the interfaces installed in the printer will be displayed. Optional cards may be added to provide additional ports for output of the debug trace data. Operations - Common - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 82
had been pressed in the operator panel. Restore ALL SCS/TNe emulation option settings to factory defaults. All sessions will be disconnected. All TNe sessions will have to be reconfigured. Other printer emulation settings (PCL, PS, IPDS, etc.) are not reset when this option is selected. Operations - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 83
and options. Settings under this menu are used when printing from a Mainframe host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TNE3270E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 84
Tree diagram of the TN3270E SETUP menu structure. Operations - TN3270E SETUP: Introduction 86 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 85
SCS/TNe Emulation uses the value specified in the SCS OPTIONS menu for the option. Settings specified in an SCS job override the SCS/TNe Emulation default settings. An asterisk (*) next to a value setting indicates that the setting is currently active. The current setting for each - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 86
An Advanced IDB language command line is shown at the end of menu options which may be set by remote configuration. This shows how to remotely set the menu option to the factory default using the Advanced IDB language (cf. "IDB Basics" on page 248 ff.) Operations - TN3270E SETUP: Introduction 88 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 87
under the NETWORK SETUP menu. NETWORK SETUP Option name Print Active TN3270 Defaults Connect Status SERVER INFO Values No *, Yes Do Not Restore *, Restore Defaults Shows Primary Status Messages and Last Response Messages. Refer to Connect Status (page 92) for a description of each message. Sub - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 88
Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The printer will attempt to establish a host connection. Operations - TN3270E SETUP: NETWORK SETUP > Print Active - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 89
TN3270 Defaults This Network Setup option restores the TN3270e NETWORK SETUP factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed in the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 90
host. The option cannot be changed by the user. Normally only the primary status is shown. If problems occur, a last response message is being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN3270E SETUP > NETWORK SETUP). 2 NPA Mode = Off. - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 91
support for that device-type Lst Rsp:Name unknown to server Lst Rsp:The requested device is in use Lst Rsp:Terminal/Printer Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset the requested device type. Change the device name or - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 92
is not a terminal. Lst Rsp:The device is a partner to some terminal The SCS/TNe Emulation used the CONNECT command in its request for a specific printer. The device name requested is the partner to some terminal. Lst Rsp:Error occured An unknown error when processing the device type or name has - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 93
up to 16 characters TN Server Port 23 *, range: 0 - 65000 LU Name [undefined] *, ASCII name with up to 10 characters Device Type Specific *, Associated, Generic Keep Alive Type Telnet NOP *, None, Timing Mark Keep Alive Time 45 *, range: 1 - 32000 [seconds] A description of each SERVER INFO - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 94
Name / IP Address This Network Setup > Server Info option specifies the kind of address the SCS/TNe Emulation uses to contact the host or Telnet server. Option Value Use IP Address * Use Hostname Comments Use the IP address specified with the IP Address option. Use the hostname specified with the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 95
IP Address This Network Setup > Server Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 96
Hostname This Network Setup > Server Info option specifies the name used to identify the host to be contacted by the SCS/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 97
can be selected. While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN3270E SETUP: NETWORK SETUP > SERVER INFO > TN - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 98
name assigned to the SCS/TNe Emulation on the host or SNA gateway. Remember also to check the setting of the Device Type option. If a specific LU name is requested, then the name must be defined and available on the host. After a connection is active, the LU name can be viewed - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 99
* Associated Generic Comments Request a specific LU name. Make sure this has been defined and is available on the host or SNA server. Request an associated printer which is paired with the terminal LU named in the request. Request a generic printer. The LU name is received from the pool of LU - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 100
Keep Alive Type IMPORTANT: If the Mainframe has difficulty detecting the selected signal type, try changing to another type. Check with your system administrator to determine the type of signal to select. This Network Setup > Server Info option specifies the type - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 101
Keep Alive Time This Network Setup > Server Info option specifies the time in seconds that expires between each keep alive signal sent to the host or SNA gateway server. The Keep Alive Type setting specifies the type of signal sent to the host. Set this option to a value smaller than the session's - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 102
IDB Option 122) MISC SETTINGS PAPER SETTINGS Values Yes *, No Sub-menu. See SCS Options > MISC SETTINGS Menu: Options Overview (page 106) and FF Support (IDB Option 5) (page 108). Sub-menu. See SCS Options > PAPER SETTINGS Menu: Options Overview (page 133) and Left Margin (IDB Option 103) (page 135 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 103
on page formatting commands received from the host. If the document does not fit on a page in portrait orientation, the orientation is changed to landscape. Option Value No Yes * IDB Value 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:2:EXIT Operations - TN3270E SETUP - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 104
menu. The following table lists menu options and sub-menus found under the MISC SETTINGS menu. SCS OPTIONS >MISC SETTINGS Option name FF Support (IDB Option 5) Non-Print Char (IDB Option 3) CSC Characters (IDB Options 8 & 9) IDB Delimiter (IDB Option 7) Use IR (IDB Option 21) Format Ctrl Sup - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 105
(IDB Option 167) Form Strings (IDB Option 168) IBM Trn Code (IDB Option 169 bit 1) Leadin Sequence (IDB Option 169 bit2) Euro Support (IDB Event 191) BOLD PRINT Values 132 *, range: 1 - 255 6 *, range: 1 - 255 Single *, Double 64 *, range: 1 - 255 Intermate *, Axis, Enable MPI feat ASCII - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 106
FF Support (IDB Option 5) This SCS Options > MISC Settings option defines if a form feed and/or a line feed is generated when & FF IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 5:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > FF Support (IDB Option 5) 108 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 107
Non-Print Char (IDB Option 3) This SCS Options > MISC Settings option defines the replacement character to substitute for an unprintable character found in the data stream. Refer to "Appendix B - ASCII Character Table" on page 282 for a complete list of printable characters and their values. - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 108
of the Leadin characters defined with option 171 and 172. Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option values are ASCII characters in the decimal range 33 - 126. Refer to "Appendix B - ASCII Character Table" on page 282 for - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 109
IDB Delimiter (IDB Option 7) This SCS Options > MISC Settings option defines the delimiter used in the Advanced IDB command language to separate programming commands. The IDB option value is an ASCII character in the decimal range 32 - 126. Refer to "Appendix B - ASCII Character Table" on page 282 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 110
Options > MISC Settings option controls Intervention Required (IR) reporting to the host. If the option is enabled, IR signals are sent when the printer reports a Paper Out, Paper Jam, goes Off-line etc. Option Value Off * On Value Description No IR signals are sent IR signals are sent IDB Value - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 111
Host direct print and Local Copy print. It can be enabled with the -M command. All host generated codes are still sent. Is diabled after Power On in Host direct print. It can be enabled with the -M command. All host generated codes are still sent. CR, LF, NL and FF - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 112
-M command. The auto-NL is still enabled. Standard handling of control codes after Power On. If the +M command is used, CR, LF, NL and FF codes All host generated control codes are still sent to the printer. Operations - TN3270E SETUP: MISC SETTINGS > Format Ctrl Sup (IDB Option 177) 114 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 113
suppressed and the auto-NL function is disabled. Control codes can only be sent to the printer with one of the transparent commands. NOTE: The effect of the +M command is reset per job. - M [m]: After this command, all Host generated control codes are processed and the auto-NL function - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 114
Country Code (IDB Option 2) This SCS Options > MISC Settings option defines the character set. Option Value Aus/Ger Aus/Ger (alt) Belgian Brazilian Can Bilin Can French Dan/Nor Dan/Nor (alt) English (UK) English (US) * Fin/Swe Fin/Swe (alt) Fre/Azerty International Italian IDB Value 2 3 4 5 6 7 8 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 115
Alternate Swiss German/Swiss French Japanese/English Spanish data/text processing NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to English (UK). See the SCS3270 Defaults option. Advanced IDB language to set factory default: &%IDB_EDIT - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 116
Skip Blank Page (IDB Option 32) This SCS Options > MISC Settings option controls whether or not blank pages are printed. With this option enabled, pages containing only a CR, NL, LF or FF are skipped. Option Value Do Not Skip * Skip IDB Value 0 1 Advanced IDB language to set factory default: &% - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 117
CPI (IDB Option This SCS Options > MISC Settings option defines the number of 100) characters per inch. Option Value 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 10 12 15 16 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 100:10:EXIT Operations - TN3270E SETUP: MISC SETTINGS > CPI - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 118
Max Prt Pos (IDB This SCS Options > MISC Settings option defines the maximum Option 102) number of characters per line. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 102:132:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Max Prt Pos - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 119
LPI (IDB Option This SCS Options > MISC Settings option defines the number of 105) lines per inch. Option Value 6 * [1..255] IDB Value 6 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 105:6:EXIT Operations - TN3270E SETUP: MISC SETTINGS > LPI (IDB Option 105) 121 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 120
Line Spacing (IDB Option 106) This SCS Options > MISC Settings option defines the line spacing. Option Value Single * Double IDB Value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 106:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Line Spacing (IDB Option 106) 122 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 121
) This SCS Options > MISC Settings option defines the number of lines per page. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced IDB language to set - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 122
Transparency This SCS Options > MISC Settings option selects the transpar(IDB Option 167) ency mode. Option Value Intermate * Axis Enable MPI feat IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 167:0:EXIT Operations - TN3270E SETUP: MISC SETTINGS > Transparency - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 123
Form Strings (IDB Option 168) IMPORTANT: Avoid using a character between 0 - 9 (ASCII 49 - 57), A - F (ASCII 65 - 70). Also, avoid using one of the characters used as lead in for one of the other CSC commands. This SCS Options > MISC Settings option defines the lead in character for the Formatted - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 124
IBM Trn Code (IDB Option 169 bit 1) This SCS Options > MISC Settings option defines how transparent data is translated. Option Value Normal * No Translation IDB bit option value Comments 0 Transparent data is translated from EBCDIC to ASCII. Data outside the range 40H - FEH is printed as a - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 125
option defines the kind of lead in sequence used. Option Value Normal * Without '&%' IDB bit option value Comments 0 Normal user defined trans- parent handling. 1 User defined transparent lead in characters are used without the pass through sequence. See the CSC Characters (IDB Options - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 126
This SCS Options > MISC Settings option controls Euro character (IDB Event 191) print support. Option Value No * Yes Comments Disable Euro Support. Enable Euro Support. The ASCII character 186d (0xBAh) is converted to the Euro ASCII character 213d (0xD5h) in symbol set 13U. Operations - TN3270E - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 127
SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview The BOLD PRINT menu is a sub-menu under the MISC SETTINGS menu. The following table lists menu options found under the BOLD PRINT menu. SCS OPTIONS > MISC SETTINGS> BOLD PRINT Option name Bold On CR (IDB Option 22 bit 1) Bold On BS ( - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 128
Bold On CR (IDB This SCS Options > MISC Settings > BOLD PRINT option defines Option 22 bit 1) whether or not bold printing is enabled on a carriage return (CR). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 129
Bold On BS (IDB This SCS Options > MISC Settings > BOLD PRINT option defines Option 22 bit 2) whether or not bold printing is enabled on a backspace (BS). Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 130
Bold On Multi BS (IDB Opt. 22 bit 3) This SCS Options > MISC Settings > BOLD PRINT option defines whether or not bold printing is enabled on multiple backspaces. Option Value No Yes * IDB bit option value 0 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 22:7:EXIT Operations - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 131
SCS Options > PAPER SETTINGS Menu: Options Overview The PAPER SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options found under the PAPER SETTINGS menu. Option name Left Margin (IDB Option 103) Right Margin (IDB Option 104) Top Margin (IDB Option 108) - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 132
A description of each PAPER SETTINGS menu option follows. Operations - TN3270E SETUP: SCS Options > PAPER SETTINGS Menu: Options Overview 134 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 133
Left Margin (IDB Option 103) This SCS Options > Paper Settings option defines the left margin position in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 134
Right Margin (IDB Option 104) This SCS Options > Paper Settings option defines the right margin position in characters. The character width depends on the setting of the CPI (IDB Option 100) option. Option Value 132 * [1..255] IDB Value 132 Advanced IDB language to set factory default: &% - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 135
Top Margin (IDB Option 108) This SCS Options > Paper Settings option defines line number position of the top margin. The line height depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 136
. The line height depends on the setting of the LPI (IDB Option 105) option. NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to 66. See the SCS3270 Defaults option. Option Value 64 * [1..255] IDB Value 64 Advanced IDB language to set - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 137
IDB Option 113) source. Option Value Prtr Setting Tray 1 * Tray 2 Tray 3 Tray 4 Tray 5 IDB Value 0 1 2 3 4 5 Comments Feed paper from the paper source selected in the printer PAPER MENU Paper Source menu. Paper is fed from Tray 1 Paper is fed from Tray 2 Paper is fed from Tray 3 Paper is fed from - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 138
Tray 1 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 123) tation for source input tray 1. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 123:2:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 139
Tray 2 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 124) tation for source input tray 2. Option Value Portrait Landscape COR * IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 124:2:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 140
Tray 3 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 125) tation for source input tray 3. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 125:0:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 141
Tray 4 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 126) tation for source input tray 4. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 126:0:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 142
Tray 5 Orient This SCS Options > Paper Settings option selects the page orien(IDB Option 127) tation for source input tray 5. Option Value Portrait * Landscape COR IDB Value 0 1 2 Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 127:0:EXIT Operations - TN3270E SETUP: SCS Options - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 143
the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 144
the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 145
the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 146
the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 147
the print area for rotations of job text. See the COR/APO Sett (IDB Option 122) option. Option Value A4 B5 Letter * Legal IDB Value 0 1 2 See note below. 3 NOTE: If the SCS options are restored to non-US factory defaults, the default value of this option changes to A4. See the SCS3270 Defaults - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 148
. Option name Values SCS3270 Hex Dump Normal Mode *, Hex Dump-Mode Print 3270 IDB Do Not Print *, Print SCS3270 Defaults Do Not Restore *, US-Default, Non-US-Default A description of each TEST OPTIONS menu item follows. Operations - TN3270E SETUP: TEST OPTIONS Menu: Options Overview 150 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 149
that a hex dump is not produced even though this option is set to Hex Dump-Mode. Option Value Normal Mode * Hex Dump-Mode Comments Normal printer operation. Print job as hex characters without executing control codes. Operations - TN3270E SETUP: TEST OPTIONS > SCS3270 Hex Dump 151 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 150
Print 3270 IDB This Test option prints a tabular report of the current IDB settings using option numbers. Print this report when asked by technical support representatives. Option Value Do Not Print * Print Comments Do not print the IDB settings. This performs the same action as if Back had been - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 151
TN3270e SCS OPTIONS setting to their factory default settings. Other printer emulation defaults are unchanged. The restored settings become active on the next SCS job. Option Value Do Not Restore * US-Default Non-US-Default Comments Do not restore any settings. This performs the same action as if - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 152
Tray2 Paper Size (IDB Option 91) Tray3 Paper Size (IDB Option 92) Tray4 Paper Size (IDB Option 93) Tray5 Paper Size (IDB Option 94) FF Support (IDB Option 5) COR/APO Sett (IDB Option 122) US-Default Letter Letter Letter Letter Always FF Yes Non-US-Default A4 A4 A4 A4 Always - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 153
under this menu are used when printing from an AS/400 or iSeries host. From a Ready status, touch Menus. Locate and touch the Option Card Menu. Locate and touch SCS/TNe Menu. Locate and touch TN5250E SETUP. SCS/TNe MENU COMMON SETUP TN3270E SETUP TN5250E SETUP Settings are displayed under - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 154
Tree diagram of the TN5250E SETUP menu structure. Operations - TN5250E SETUP: Introduction 156 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 155
SCS/TNe Emulation uses the value specified in the SCS OPTIONS menu for the option. Settings specified in an SCS job override the SCS/TNe Emulation default settings. An asterisk (*) next to a value setting indicates that the setting is currently active. The current setting for each - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 156
be set by remote configuration. Following this are two command lines, one for the User IDB language and another for the Advanced IDB language. These show how to remotely 248 ff. - and see "Additional TN5250e Printer Commands Using IDB" on page 260 ff.) Operations - TN5250E SETUP: Introduction 158 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 157
means that changes made under the SCS OPTIONS menu settings affect the way all TN5250E jobs are printed. The following table lists menu options found under the CONNECTION#1 - CONNECTION#4 menus. Option name Values Print # Active No *, Yes TN5250## Default Do Not Restore *, Restore - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 158
the activation of the SCS/TNe Emulation for TN5250E communication and printing. Option Value No * Yes Comments SCS printing is disabled for this connection. The printer will not attempt to establish a host connection. SCS printing is enabled for this connection. The - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 159
#2, #3, or #4 factory default settings and resets all sessions. Option Value Do Not Restore * Restore Defaults Comments Do not restore to factory default settings. This performs the same action as if Back had been pressed in the operator panel. Restore the TN5250 CONNECTION ## menu options for the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 160
the connection status with the host. The option cannot be changed by the user. The first part of the line shows the primary status being estalished. 1 Print Active = No. Solution: Set to Yes. (Path: Menus > Option Card Menu > SCS/TNe MENU > TN5250E SETUP > CONNECTION #). 2 NPA Mode = Off. Solution: - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 161
Comments Session Disconnected and Halted All active Telnet sessions have been disconnected. Power the printer Off and On or select Menus > Option Card Menu > SCS/ TNe MENU > COMMON SETUP > Reset TN Session > Reset TN Ses. to reconnect. Session established on system [SYSTEM NAME] A Telnet - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 162
device found Lst Rsp:8917:Not authorized to object Lst Rsp:8918:Job canceled Lst Rsp:8920:Object partially damaged Lst Rsp:8921:Communication error Lst -up record incorrectly Lst Rsp:8925:Creation of device failed Lst Rsp:8928:Change of device failed Lst Rsp:8929:Vary on or vary off failed Lst - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 163
Connect # Status: Last response messages Lst Rsp:8935:Session rejected Lst Rsp:8936:Security failure on session Lst Rsp:8937:Automatic sign-on rejected Lst Rsp:8940:Automatic config. failed Lst Rsp:I904:Source at incompatible release Comments Check with system operator. Check with system operator. - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 164
Connection# > SERVER # INFO Option name Keep Alive Time MSGQ # Name MSGQ # Lib IR # Reply Auto Sense # END Values 45 *, range: 1 - 32000 [seconds] QSYSOPR *, ASCII name with up to 10 characters. *LIBL *, ASCII name with up to 10 characters. Normal *, Offline, No Reply No *, Yes A description of - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 165
IP # Address This Connection# > Server# Info option specifies the specific IP address of the host to be contacted by the SCS/TNe Emulation. Option Value 0.0.0.0 * Comments Contact your network administrator for the IP address to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 166
Hostname # This Connection# > Server# Info option specifies the name used to identify the host to be contacted by the SCS/TNe Emulation. Option Value [undefined] * Comments Any ASCII text string up to 16 characters. Contact your system administrator for information on the hostname to use. - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 167
selected. While a large range of port numbers can be selected, due to security reasons not all port numbers are available on the printer. If a value other than the default is selected, a value between 1024 and 65000 is recommended. Operations - TN5250E SETUP: CONNECTION # > SERVER # INFO > Server - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 168
Device # Name This Connection# > Server# Info option specifies the device and writer name associated with the SCS/TNe Emulation on the host. A device and writer will be auto configured with this name if it does not already exist. Option Value [undefined] * Comments Any ASCII text string up to 10 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 169
Keep Alive Type IMPORTANT: If the host has difficulty detecting the selected signal type, try changing to another type. Check with your system administrator to determine the type of signal to select. This Connection# > Server# Info option specifies the type of - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 170
Keep Alive Time TIP: Set this option to as big a value as possible. Be sure it is smaller than the session's inactivity timeout value defined on the host. This will help minimize network traffic. This Connection# > Server# Info option specifies the time in seconds that expires between each keep - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 171
MSGQ # Name This Connection# > Server# Info option specifies the message queue name on the host to which Intervention Required conditions are reported. The message queue name must already exist on the host. It will not be auto created. The MSGQ # Lib option may be used to set the message queue - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 172
MSGQ # Lib This Connection# > Server# Info option specifies the message queue library for the message queue specified in the MSGQ # Name option. The message queue library must already exist on the host. It will not be auto created. Leave this option at the default if you do not know the library - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 173
the reporting of Intervention Required Replies to the host. Option Value Normal * Offline No Reply Comments Use normal IR replies, i.e. send paper jam as paper jam, paper out as paper out etc. Only send IR replies as offline messages without specifying what kind of IR has occurred. Disable the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 174
automatically if the host has ended the Writer. This may be necessary due to the host's management of the print queue when more than one job is in the same queue. Option Value No * Yes Comments Do not sense if writer ends. Sense if writer ends, reconnect, and reconfigure automatically. Operations - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 175
) Use Escape *, Use Line feed, Space + Escape, Linefeed + Esc Format Ctrl Sup (IDB Option 177) Enabled *, Disabled Download Font (IDB Option 244) Enabled *, Disabled Euro Support (IDB Option 139) No *, Yes Operations - TN5250E SETUP: SCS OPTIONS Menu: Options Overview 177 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 176
SCS OPTIONS Option name CSC CHARACTERS COR/APO SETTINGS MISC SETTINGS PAPER SETTINGS Values Sub-menu. See SCS OPTIONS > CSC CHARACTERS Menu: Options Overview (page 192) and SCS OPTIONS > CSC CHARACTERS Menu: Options Overview (page192). Sub-menu. See SCS OPTIONS > COR/APO SETTINGS Menu: Options - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 177
2 will be executed if paper tray 2 has been selected. Option Value Disable * Enable IDB Value 0 1 User IDB parameter OFF ON User IDB command: OVLCAL : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: OVLCAL OFF:EXIT Operations - TN5250E SETUP: SCS OPTIONS - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 178
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 28:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Overlay Call (IDB Option 28) 180 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 179
proportional font handling. The individual character width values of the printer's native fonts must correspond to the width value which . Option Value Do Not Use * Use IDB Value 0 1 User IDB parameter OFF ON User IDB command: PRPFNTMOV : Parameter: OFF, ON Operations - TN5250E - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 180
User IDB language to set factory default: &%IDB_EDIT: PRPFNTMOV OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 118:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Prop Font Move (IDB Option 118) 182 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 181
The command is used to compensate for the reduced printable area of the printer. The option makes it possible to print 80 characters on a line C-----P----I---×-----5---0-49 Option Value Off * On IDB Value 0 1 User IDB parameter OFF ON Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 182
User IDB command: COMCPI : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: COMCPI OFF:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 128:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Compress CPI (IDB Option 128) 184 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 183
HORMOV / VERMOV : Parameter: For HORMOV ESC uses escape sequences; SP uses spaces For VERMOV ESC uses escape sequences; LF uses line feeds User IDB language to set factory default: &%IDB_EDIT: HORMOV ESC: VERMOV ESC:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 184
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 158:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Move Hor/Ver (IDB Option 158) 186 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 185
is incorrectly double spaced, disabling it will in most cases solve the problem. Option Value Enabled * Disabled IDB Value 0 1 User IDB parameter ON OFF User IDB command: CTLCODSUP : Parameter: OFF, ON User IDB language to set factory default: &%IDB_EDIT: CTLCODSUP ON:EXIT Advanced - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 186
these fonts will be downloaded to the printer's memory at Power On. The additional fonts are listed in the table below. The fonts marked with a + contain the Euro character. Option Value Disabled Enabled * IDB Value 0 1 User IDB parameter Not supported Not supported Font IBM font no. PCL font - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 187
User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 244:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > Download Font (IDB Option 244) 189 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 188
Euro Support (IDB Option 139) This SCS Options option controls Euro character printing. If the option is set to Yes, the normal 284 1145 UK 285 1146 France 297 1147 Multinational 500 1148 Iceland 871 1149 Operations - TN5250E SETUP: SCS OPTIONS > Euro Support (IDB Option 139) 190 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 189
In order to be able to print the Euro character a font supporting the character also has to be selected and available in the printer. See the Download Font (IDB Option 244) option on page 188 and the Font (IDB Options 242 and 243) option on page 215. Option Value - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 190
SCS OPTIONS > CSC CHARACTERS Menu: Options Overview The CSC CHARACTERS menu is a sub-menu directly under the SCS OPTIONS menu. The following table lists menu options found under the CSC CHARACTERS menu. SCS OPTIONS > CSC Characters Option name IDB First Char (IDB Option 8) IDB Second Char (IDB - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 191
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in the IDB Value 38 [ampersand] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 192
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 8:38:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB First Char (IDB Option 8) 194 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 193
Last of all the CSC is also used for passing single hex values to the printer, e.g. &%1B = . The IDB option value is an ASCII character in the * IDB Value 37 [percent] User IDB command: Not supported Parameter: Not supported User IDB parameter Not supported Operations - TN5250E SETUP: SCS - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 194
User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 9:37:EXIT Operations - TN5250E SETUP: SCS OPTIONS > IDB Second Char (IDB Option 9) 196 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 195
list of characters and their values. Option Value : * IDB Value 58 [colon] User IDB parameter Not supported User IDB command: Not supported Parameter: Not supported User IDB language to set factory default: Not supported Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 7:58:EXIT - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 196
SCS OPTIONS > COR/APO SETTINGS Menu: Options Overview The COR/APO SETTINGS menu is a sub-menu directly under the SCS OPTIONS menu. The following table lists menu options found under the COR/APO SETTINGS menu. SCS Options > COR/APO Settings Option name Values Def Page Ori 1 (IDB Option 121) - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 197
COR Action 1 (IDB Option 123) option. Option Value Prtr Setting Portrait * Landscape IDB Value 0 1 2 User IDB parameter DEF POR LAN User IDB command: ORTDRW 1 : Parameter: DEF, POR, LAN User IDB language to set factory default: &%IDB_EDIT: ORTDRW 1 POR:EXIT Advanced IDB language to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 198
IDB command: ORTDRW 2 : Parameter: DEF, POR, LAN User IDB language to set factory default: &%IDB_EDIT: ORTDRW 2 POR:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 122:1:EXI Operations - TN5250E SETUP: SCS OPTIONS > COR/APO SETTINGS > Def Page Ori 2 (IDB Option 200 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 199
Output Reduction) works for paper tray 1. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between Landscape and Portrait (APO) only, or it can be stated that automatic reduction (COR) is - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 200
. Option Value IDB Value Disable 0 Enable APO 1 Enable Auto COR * 2 Disable STO 3 User IDB parameter OFF APO COR STODIS User IDB command: CORDRW 1 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 1 COR:EXIT Advanced IDB language to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 201
) works for paper tray 2 and above. With this option it is possible to disable the APO/COR function so that the page orientation change only can be made manually. It is also possible to select between Landscape and Portrait (APO) only, or it can be stated that automatic reduction (COR) is performed - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 202
. Option Value IDB Value Disable 0 Enable APO 1 Enable Auto COR * 2 Disable STO 3 User IDB parameter OFF APO COR STODIS User IDB command: CORDRW 2 : Parameter: OFF, APO, COR, STODIS User IDB language to set factory default: &%IDB_EDIT: CORDRW 2 COR:EXIT Advanced IDB language to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 203
to disable text mode. When text mode is disabled, the APO/COR function will ignore the print quality parameter and print all print jobs fulfilling the requirements in computer output reduction mode. Refer to "Appendix D - COR/APO Logic (TN5250e)" on page 287 Operations - TN5250E SETUP: SCS OPTIONS - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 204
OFF Normal IBM interpretation ON Ignore the system TEXT parameter APO Observe TEXT parameter in APO as well User IDB command: TXTMOD : Parameter: OFF, ON, APO User IDB language to set factory default: &%IDB_EDIT: TXTMOD OFF:EXIT Advanced IDB language to set factory default - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 205
to 70% of the normal line spacing (100%). Option Value 70% * [1..100] IDB Value 70 User IDB parameter 70 User IDB command: LINSPRED : Parameter: 1 - 100 percent of normal line spacing User IDB language to set factory default: &%IDB_EDIT: LINSPRED 70:EXIT Advanced IDB language to set - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 206
SCS OPTIONS > MISC SETTINGS Menu: Options Overview The MISC SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options and sub-menus found under the MISC SETTINGS menu. SCS OPTIONS>MISC SETTINGS Option name Country Code (IDB Option 2) Codepage (IDB Options 240 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 207
SCS OPTIONS>MISC SETTINGS Option name Lines Per Page (IDB Option 107) Top Margin (IDB Option 108) Source Input (IDB Option 113) Forms Media (IDB Option 114) Output Bin (IDB Option 115) Simplex/Duplex (IDB Option 116) Non-Print Char (IDB Option 3) Values 68 *, range: 1 - 255 1 *, range: 1 - 255 Tray - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 208
country codes. In country codes other than International country specific characters replace selected characters. Option Value International * USA/ ) USA/Can bil. Portugal IDB Value 0 1 2 3 4 5 6 7 8 9 10 11 12 User IDB parameter 0 1 2 3 4 5 6 7 8 9 10 11 12 Operations - TN5250E SETUP: SCS OPTIONS - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 209
Option Value Spain Latin America English (UK) IDB Value 13 14 15 User IDB parameter 13 14 15 User IDB command: DEFCNTCOD : Parameter: 0 - 15 User IDB language to set factory default: &%IDB_EDIT: DEFCNTCOD 0:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 2:0: - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 210
/Nor 277 Fin/Swe 278 Italy 280 Jap/Eng 281 Portugal 282 Spain 284 Eng (UK) 285 France 297 IDB Values (Option 240 and 241) User IDB parameter 37 + 0 37 3 + 1 259 17 + 1 273 18 + 1 274 19 + 1 275 21 + 1 277 22 + 1 278 24 + 1 280 25 + 1 281 26 + 1 282 28 + 1 284 29 + 1 285 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 211
1144 120 + 4 1144 Spain 1145 121 + 4 1145 Eng (UK) 1146 122 + 4 1146 France 1147 123 + 4 1147 Multi. 1148 124 + 4 1148 Iceland 1149 125 + 4 1149 User IDB command: DEFCODPAG : Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 213 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 212
Parameter: 37 - 1149 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFCODPAG 500:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 240:244: OPTION 241:1:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Codepage (IDB Options 240 and 214 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 213
from the system. Fonts in shaded rows may be loaded into printer memory. See the Download Font (IDB Option 244) option. Option 12 110 Let.Got. Bld 12 111 Pres. Bold 12 112 Pres. It 12 IDB Value (Option 242 and 243) User IDB parameter 3 + 0 3 11 + 0 11 18 + 0 18 39 + 0 39 40 + 0 40 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 214
Got.Text 20 290 Got.Text 27 751 Son.Ser. 7 1051 Son.Ser. 10 1053 Son.Ser.Bld 10 IDB Value (Option 242 and 243) User IDB parameter 155 + 0 155 159 + 0 159 160 + 0 160 163 + 0 163 175 + 0 175 204 + 0 204 221 + 0 221 222 + 0 222 223 + 0 223 230 + 0 230 244 + 0 244 245 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 215
.Ser.Bld 16 2103 Son.Ser.Bld 24 IDB Value (Option 242 and 243) User IDB parameter 32 + 4 1056 71 + 5 1351 117 + 6 1653 35 + 8 2103 User IDB command: DEFFNT : Parameter: 3 - 2103 as listed above User IDB language to set factory default: &%IDB_EDIT: DEFFNT 11:EXIT Advanced IDB - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 216
inch). Option Value 5 CPI 10 CPI * 12 CPI 15 CPI 16.7 CPI IDB Value 5 10 12 15 16 User IDB parameter 5 10 12 15 16 User IDB command: DEFCPI : Parameter: 5, 10, 12, 15, 16 User IDB language to set factory default: &%IDB_EDIT: DEFCPI 10:EXIT Advanced IDB language to set factory default - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 217
defines the maximum (IDB Option 102) horizontal print position. Option Value 80 * [1..254] IDB Value 80 User IDB parameter 80 User IDB command: DEFMPP : Parameter: 1 - 254 User IDB language to set factory default: &%IDB_EDIT: DEFMPP 80:EXIT Advanced IDB language to set factory default - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 218
depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFLFTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLFTMRG 1:EXIT Advanced IDB language to set factory default - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 219
depends on the setting of the CPI (IDB Option 100) option. Option Value 1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFRGTMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFRGTMRG 1:EXIT Advanced IDB language to set factory default - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 220
of 105) lines per inch (LPI). Option Value 3 LPI 4 LPI 6 LPI * 8 LPI 9 LPI IDB Value 3 4 6 8 9 User IDB parameter 3 4 6 8 9 User IDB command: DEFLPI : Parameter: 3, 4, 6, 8, 9 User IDB language to set factory default: &%IDB_EDIT: DEFLPI 6:EXIT Advanced IDB language to set factory - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 221
option defines the number of (IDB Option 107) lines per page. Option Value 68 * [1..255] IDB Value 68 User IDB parameter 68 User IDB command: DEFLPP : Parameter: 0 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFLPP 68:EXIT Advanced IDB language to set factory default - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 222
depends on the setting of the LPI (IDB Option 105) option. Option Value 1 * [1..255] IDB Value 1 User IDB parameter 1 User IDB command: DEFTOPMRG : Parameter: 1 - 255 User IDB language to set factory default: &%IDB_EDIT: DEFTOPMRG 1:EXIT Advanced IDB language to set factory default - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 223
contain a string which selects a specific tray in the printer. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page 4. User IDB command: DEFSRCDRW : Parameter: DEF, 1, 2, 3, 4, 5, 6, 7, 8 User IDB language to set - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 224
Select Media (SLTMED) command. Option Value Prtr Setting * Paper Media Envelope Med IDB Value 0 1 2 User IDB parameter DEF PAP ENV User IDB command: DEFFRMSEL : Parameter: DEF, PAP, ENV User IDB language to set factory default: &%IDB_EDIT: DEFFRMSEL DEF:EXIT Advanced IDB language to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 225
(DSTDRW) command. Option Value Prtr Setting * Output Bin 1 Output Bin 2 Output Bin 3 IDB Value 0 1 2 3 User IDB parameter DEF 1 2 3 User IDB command: DEFDSTDRW : Parameter: DEF, 1, 2, 3 User IDB language to set factory default: &%IDB_EDIT: DEFDSTDRW DEF:EXIT Advanced IDB language to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 226
or bound at the top. NOTE: The Duplex and Duplex (Tumble) settings display only on printers with duplex support. Option Value Prtr Setting * Simplex Duplex Duplex (Tumble) IDB Value 0 1 2 3 User IDB parameter DEF SIM DUP TUM User IDB command: DEFSIMDUP : Parameter: DEF, SIM, DUP, TUM - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 227
Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 116:0:EXIT Operations - TN5250E SETUP: SCS OPTIONS > MISC SETTINGS > Simplex/Duplex (IDB Option 116) 229 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 228
for an unprintable character found in the data stream. The character is printed when the host sends an unprintable character or a character not supported by the SCS/TNe Emulation. Refer to "Appendix B - ASCII Character Table" on page 282 for a complete list of printable characters and their values - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 229
SCS OPTIONS > PAPER SETTINGS Menu: Options Overview The PAPER SETTINGS menu is a sub-menu under the SCS OPTIONS menu. The following table lists menu options found under the PAPER SETTINGS menu. SCS Options > Paper Settings Option name Left Margin COR (IDB Opt. 78 & 79) Top Margin COR (IDB Opt. 80 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 230
command: LFTOFFCOR : Parameter 1: I for inches, C for centimeters Parameter 2: Value in inches [0.00 .. 2.009 or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFCOR I 0.44:EXIT Advanced IDB language to set factory - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 231
The option values for option 78 and 79 are calculated using the formulas below. 79: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 78: (Marg. inch × 1440) - (256 × Value stored in option 79) Round off to nearest whole number. The values stored in - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 232
1> : Parameter 1: I for inches, C for centimeters Parameter 2: Value in inches [0.00 .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFCOR I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 80 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 233
The option values for option 80 and 81 are calculated using the formulas below. 81: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 80: (Marg. inch × 1440) - (256 × Value stored in option 81) Round off to nearest whole number. The values stored in - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 234
1> : Parameter 1: I for inches, C for centimeters Parameter 2: Value in inches [0.00 .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: LFTOFFLAN I 0.00:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 86 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 235
The option values for option 86 and 87 are calculated using the formulas below. 87: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 86: (Marg. inch × 1440) - (256 × Value stored in option 87) Round off to nearest whole number. The values stored in - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 236
command: TOPOFFLAN : Parameter 1: I for inches, C for centimeters Parameter 2: Value in inches [0.00 .. 2.00] or centimeters [0.00 .. 5.08] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: TOPOFFLAN I 0.10:EXIT Advanced IDB language to set factory - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 237
The option values for option 88 and 89 are calculated using the formulas below. 89: M-----a----r--g---.----i-n---c---h-----×-----1---4----4---0-- Reduce to nearest whole number. 256 88: (Marg. inch × 1440) - (256 × Value stored in option 89) Round off to nearest whole number. The values stored in - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 238
Legal Executive Length in cm 29.70 27.94 35.56 26.67 Length in inch. 11.70 11.00 14.00 10.50 Option value 16848 15840 20160 15120 User IDB command: PAGLNG : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP: SCS OPTIONS > PAPER SETTINGS > Page - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 239
Parameter 2: Value in inches [0.00 .. 45.51] or centimeters [0.00 .. 115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGLNG I 11.70:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 82:208: OPTION 83:65: - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 240
page widths include: Paper size A4 * Letter Legal Executive Width in cm 21.00 21.59 21.59 18.42 Width in inch. 8.27 8.50 8.50 7.25 Option value 11908 12240 12240 10440 User IDB command: PAGWDT : Parameter 1: I for inches, C for centimeters Operations - TN5250E SETUP - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 241
Parameter 2: Value in inches [0.00 .. 45.51] or centimeters [0.00 .. 115.60] with 2 decimals User IDB language to set factory default: &%IDB_EDIT: PAGWDT I 8.27:EXIT Advanced IDB language to set factory default: &%IDB_EDIT: OPTION 84:132: OPTION 85:46:EXIT - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 242
menu. Option name Values SCS5250 Hex Dump Normal Mode *, Hex Dump-Mode Print 5250 IDB Do Not Print *, Print SCS5250 Defaults Do Not Restore *, Restore Defaults A description of each TEST OPTIONS menu option follows. Operations - TN5250E SETUP: TEST OPTIONS Menu: Options Overview 244 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 243
that a hex dump is not produced even though this option is set to Hex Dump-Mode. Option Value Normal Mode * Hex Dump-Mode Comments Normal printer operation. Print job as hex characters without executing control codes. Operations - TN5250E SETUP: TEST OPTIONS > SCS5250 Hex Dump 245 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 244
Print 5250 IDB This Test option prints a report listing the current IDB settings. Print this report when asked by technical support representatives. Option Value Do Not Print Print Comments Do not print the IDB settings. This performs the same action as if Back had been pressed - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 245
to Defaults their factory default values. Option Value Do Not Restore * Restore Defaults Comments Do not restore any settings. This performs the same action as if Back had been pressed in the operator panel. Restore to factory default TN5250E SCS option menu settings. Operations - TN5250E - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 246
IDB commands to change the SCS option settings remotely. Configuration of the IDB settings should only be carried out by authorized technical personal. A complete description is given in the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on page - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 247
is somewhat easier to use. However, the User IDB Language is only available for working on approximately command line sequences on the printer. This is typically done by embedding the unique IDB commands in a normal text document which is printed like any normal job. Alternatively, you can retrieve - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 248
85 and "Operations Reference - TN5250E SETUP" on page 155. The descriptions include the available options and their values. The chapter on "Additional TN5250e Printer Commands Using IDB" on page 260 covers IDB commands which can be embedded in the SCS data stream, including details on syntax. IDB - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 249
Emulation prints out the commands, or prints out error messages, it could be because the characters used for programming (& % E : ...etc) have been corrupted. You must reset the SCS OPTIONS to their factory defaults. IDB Basics: IDB Languages Usage 251 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 250
sending the command: &%IDB_EDIT: and leave configuration mode, by sending the trailer string: EXIT This causes the changed options to be saved. The new option settings are active on the next SCS job. All configuration options must be separated by a colon. Line feed, form feed etc. should be avoided - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 251
Programming examples Advanced IDB (TN3270E + TN5250E) User IDB (TN5250E) Valid &%IDB_EDIT: &%IDB_EDIT: - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 252
editing is done, it is possible to save the settings in a file. The resulting IDB Configuration File can then be downloaded to one or more printers containing an SCS/TNe Emulation providing easy, fast, and uniform setups. IDB Basics: IDB Configuration File Management 254 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 253
IDB settings controlling how SCS jobs print can be retrieved via FTP. The name of the file is fixed and cannot be changed. The procedure below uses a Microsoft FTP client. To retrieve the IDB settings file 1 Start a FTP session. ftp 201.1.12.123 (Sample IP address) User name: 2 Enter the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 254
5 End the FTP session. bye IDB Basics: Retrieving the IDB Configuration File 256 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 255
file is DOS based and is available on the internet site with manual updates listed in "Support" on page 4. Look for the following files. Protocol File options and events not described in this guide. Only options and events described in this guide should be configured.The IDB configuration file - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 256
different name will result in an unreadable printout. No IDB settings will be changed. The procedure below uses a Microsoft FTP client. To store the IDB settings file 1 Start a FTP session. ftp 201.1.12.123 (Sample IP address) User name: 2 Enter the "/lti" directory. cd /lti 3 Set the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 257
4 Store the IDB configuration file. put c:\tn3270e.idb put c:\tn5250e.idb (TN3270E users) (TN5250E users) This stores the file from a PC's root directory. 5 End the FTP session. bye The downloaded IDB settings are active on the next SCS job. IDB Basics: Storing the IDB Configuration File 259 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 258
Commands Using IDB Introduction The IDB commands described here provide additional commands for controlling the printer. This chapter presents the syntax for creating these commands, which must be sent from the AS/400 or iSeries in order to be recognized, i.e. included - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 259
Input Data String Syntax The input data string () following some printer commands can contain three parts: Text, decimal numbers, and hexadecimal numbers. Text: Text has to be put in quotation marks. "This is a text" Decimal: Decimal - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 260
to set up four strings of 1024 bytes each which are sent to the printer at power On. The events can be used to download a small logo or set the printer to a specific emulation. Power On sequence 1 Power On, events 0, 1 and 2 are triggered. 2 DEFMPP (Max print positions) is selected. 3 DEFCPI (CPI - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 261
> : POWON DEL : Parameter: 1 - 4 Example: POWON 3 "Power initialize 3": POWON DEL 3: Delete command Definition number The rest of this chapter is devoted to a run-through of the commands you can work with. TN5250e Printer Commands Using IDB: Initializing - Power On Initialize 263 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 262
Page Presentation Media) when a specific input tray is selected. It can also be triggered by the DEFSRCDRW command at Power On. See section "Source select a specific input tray. Refer to the IDB Technical Reference guide, available on the internet site with manual updates listed in "Support" on - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 263
output drawer (bin) is selected. It can also be triggered by the DEFDSTDRW command at Power On. See section "Output Bin (IDB Option 115)" on page 227. The command corresponds to bin 1 Delete command string for dest.drawer 1 TN5250e Printer Commands Using IDB: Paper Handling > Destination Drawer 265 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 264
on paper or envelopes is selected. It can also be triggered by the DEFFRMSEL command at Power On. See section "Forms Media (IDB Option 114)" on page 226. The command corresponds PAP "Paper media": SLTMED DEL ENV: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper / Envelope Media 266 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 265
: SLTPAPFED : SLTPAPFED DEL : Delete command Parameter: CON CUT MAN Select continuous paper feed Select cutsheet feed Select manual feed Example: SLTPAPFED MAN /1B,"&l2H": SLTPAPFED DEL CUT: TN5250e Printer Commands Using IDB: Paper Handling > Select Paper Feed 267 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 266
The command can only be used if the printer supports duplex printing. It is triggered by the AS/400 or iSeries command PPM (Page Presentation Media) when simplex or duplex printing is selected. It can also be triggered by the DEFSIMDUP command at Power - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 267
the symbols and signs are not contained in the normal character set of the printer which means that they cannot be used from AS/400 or iSeries. With this command it is possible to switch to another character set in the printer each time code page 259 is used. This can be used to switch to - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 268
Parameter: BEF AFT Before code page 259 selection After code page 259 selection Example: COD259 BEF "Command": COD259 DEL AFT: TN5250e Printer Commands Using IDB: Code Page 259 > Before/After 270 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 269
: OVLDRW DEL : Delete command Parameter: 1 - 2 Drawer number Example: OVLDRW 1 /1B,"&f3Y",/1B,"&f2X":PCL string for calling macro no. 3 OVLDRW DEL 1: TN5250e Printer Commands Using IDB: Miscellaneous > Overlay Command 271 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 270
Formfeed Command: BEFAFTFED : BEFAFTFED DEL : Parameter: BEF AFT Example: BEFAFTFED BEF "Command": BEDAFTFED DEF AFT: Delete command Before formfeed After formfeed TN5250e Printer Commands Using IDB: Miscellaneous > Before / After Formfeed 272 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 271
selection Example: BEFPORLAN POR /1B,"&l0E",/1B,"&a0V": PCL command for setting top margin to 0 and moving print position to line 0 BEFPORLAN DEL LAN: TN5250e Printer Commands Using IDB: Miscellaneous > Before Portrait/Landscape Selection 273 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 272
command is executed on the top of the first page. It may be used for stating specific information on the front page. This could be information describing which IDB profile is used, printer type, or company name. The command corresponds to event 96 - 97. Command: SUBTIT : SUBTIT - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 273
DEL: Delete command Example: MOVUPRLIN /1B,"&l0E",/1B,"&a0V":PCL command for setting top margin to 0 and moving print position to line 0 MOVUPRLIN DEL: TN5250e Printer Commands Using IDB: Miscellaneous> Move to Uppermost Line 275 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 274
Warranty included with the printer The limited warranty you received with your printer gives warranty terms and conditions. For warranty information, refer to your printer documentation. Warranty: included with the printer 276 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 275
Appendix A Specifications, Requirements, Features Product Description The SCS/TNe Emulation is an option which is installed in the printer optional firmware connector; the Card also provides IPDS emulation (see separate documentation). With the Card and a Standard Network or a MarkNet internal - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 276
Compatibility IBM Printer Emulations • 3270 SCS: IBM 3287/3812 in LU1 mode • 5250 SCS: IBM 3812-01 Compatible Print Servers • Standard Network for connection to an Ethernet LAN. • MarkNet internal print server (Ethernet) Appendix - Specifications, Requirements, Features: Compatibility 278 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 277
AS/400 Operating System OS/400 V4R1R5, or V5R1-R3 or greater. • Application System AS/400 Operating System OS/400 V3R7 with PTFs installed. Appendix - Specifications, Requirements, Features: Print Platforms 279 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 278
: 3270 SCS Features supported are dependent upon host software for selection and use. • SCS (LU1) data stream • 5 bin paper input • EBCDIC character conversion • Text string conversion • IBM and 3rd party ASCII transparency modes • EBCDIC hex-dump Appendix - Specifications, Requirements, Features - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 279
Features List: 5250 SCS Features supported are dependent upon host software for selection and use. • SCS IBM ASCII transparency • Multiple code pages and box drawing • Full OfficeVision/400 support • User Configurable SCS Features • EBCDIC character conversion • SCS command conversion • Text string - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 280
Appendix B - ASCII Character Table Printable The table shows all ASCII printable characters. Characters Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 20 space 32 38 8 56 50 P 80 68 h 104 21 ! 33 39 9 57 51 Q 81 69 i 105 22 " 34 3A : 58 52 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 281
Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal Hex ASCII Decimal 2D - 45 45 E 69 5D ] 93 75 u 117 2E . 46 46 F 70 5E ^ 94 76 v 118 2F / 47 47 G 71 5F _ 95 77 w 119 30 0 48 48 H 72 60 ' 96 78 x 120 31 1 49 49 I 73 61 a 97 79 y 121 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 282
TN3270e IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN3270E SETUP > TEST OPTIONS > SCS IDB Dump > Print. Appendix - TN3270e IDB Commands: How to Print an IDB Report 284 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 283
List of Larger numbers indicate higher precedence. Commands Precedence Command Comments 5 HEXDUMP Enter hex-dump mode (small format) 5 HEXDUMP_FULL Enter hex-dump mode (large format) 5 IDB_EDIT Enter IDB edit mode 5 IDB_PRINT Dump IDB (small format) 5 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 284
Precedence Command 2 1 {XY} Comments Double CSC (prints ) Single transparent character Refer to the chapter on Understanding the Control Panel (page 10) if necessary. Appendix - TN3270e IDB Commands: List of Commands 286 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 285
(COR) in the SCS/ TNe Emulation is switched on with the CORDRW command. The focus of this discussion is on how the printer automatic controls operate, as the user does not always have the possibility of defining whether a printout is to be rotated and compressed in the system. It Appendix - COR - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 286
that no STO commands are present in the data stream from the system. The STO commands always take priority over the automatic controls of the printer. Details The following points refer to the flowchart in the end of this appen- dix. 1 The calculation of the page format is based on information - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 287
PAGLNG = A4 and PAGWDT = A4 2 If the page format stated in the FCB is within (or equal to) the page size settings of the PAGLNG and PAGWDT option settings, the page size is "valid". In that case the printout will be in landscape provided the page length is smaller than the width, otherwise it will - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 288
font. 4 Most program applications normally have a set of standard values for page length, characters per line etc. The user might have few or no possibilities off changing, e.g., the number of characters per line, which is normally set to 132 characters. Therefore a final control exists, which - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 289
for the device. This is done by either changing the existing system printer file QSYSPRT (CHGPRTF FILE(QSYSPRT)) or creating your own printer file (CRTPRTF). Please consult your AS/400 or iSeries manuals for information on this subject. Defining the printer file to make the COR is normally done in - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 290
Example: Disable COR and set Portrait as default orientation for drawer 2 only. CORDRW 2 = OFF and ORTDRW 2 = POR Flowchart See next page. Appendix - COR/APO Logic (TN5250e): Flowchart 292 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 291
Page Orientation Logic Flowchart Appendix - COR/APO Logic (TN5250e): Flowchart 293 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 292
IDB Commands How to Print an IDB Report 1 From a Ready status in the operator panel press the MENU button. 2 Use the navigation buttons: Option Card Menu > SCS/TNe MENU > TN5250E SETUP > TEST OPTIONS > Print IDB Dump > Print. Appendix - TN5250e IDB Commands: How to Print an IDB Report 294 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 293
List of Larger numbers indicate higher precedence. Commands Precedence Command 5 IDB_EDIT 5 IDB_PRINT 5 IDB_PRINT_FULL 5 /... 5 + 5 - 5 {XY}.... 2 1 {XY} 5 IDB_STATUS 5 IDB_FONT 5 -X Comments Enter - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 294
has a programmable font table, which contains the conversion between the IBM font IDs (sent from the system) to the internal fonts used in the printer. The font table has a limit of 50 fonts + 3 fonts used for COR (Computer Output Reduction). The SCS/TNe Emulation will detect free font table - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 295
fonts. The font FGIDs are 3 (OCR-B), 155 (Boldface Italic), 159 (Boldface), 163 (Essay Bold), 160 (Essay) and 175 (Document) which may be loaded into printer memory at Power On. The font table is prepared for using these fonts. The fonts are loaded with code page PC-850 (12U) and with font ID - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 296
The "Font" Programming Command This command corresponds to the advanced IDB language FONT command. Command: PRGFNT : PRGFNT DEL : NOTE: Try to avoid deleting the first 7 fonts listed in the status printout (&%IDB_STATUS), as these fonts represent the - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 297
. Note that the IBM font numbers are divided into the groups below. pitch area IBM fonts 10 pitch: 1-65 12 pitch: 66-153 proportional: 154-200 13 pitch: 201-210 15 pitch: 211-239 5 pitch: 240-249 17 pitch: 250-257 20 pitch: 281-284 27 pitch: 290 typographic: 751-... Appendix - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 298
areas described under . The spacing determines whether the SCS/TNe Emulation or the printer has to control the spacing when using proportional fonts (Fonts with IBM no. 154 - 200). The spacing command should only be used when using downloaded proportional fonts with the correct - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 299
P Selection of "P" causes the printer to handle the character spacing. If "P" is selected in connection with programming of a font in the IBM proportional spaced area (154-200), the SCS/TNe Emulation prepares itself for support for downloaded IBM PS fonts. This ensures correct spacing of downloaded - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 300
2 The downloaded font 10175 is sent when IBM font ID 160 (Essay) is sent from the system. Font ID 160 is within the "proportional spaced" font area, and font 10175 is expected to be 100% IBM compatible as to the character spacing: PRGFNT 160 P /1B,"(s1p12.72v0s0b202T": 3 Delete all previous font - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 301
following areas. Pitch area 10 pitch: 12 pitch: prop SP : 13 pitch: 15 pitch: 17 pitch: 5 pitch: IBM font area 1 - 65 66 - 153 154 - 200 201 - 210 211 - 239 250 - 257 240 - 249 Font table position 1 3 7 4 5 6 2 Command: SETSUBFNT : NOTE: The font number must be a font number - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 302
ID 67, but all font IDs sent from the system in the range 66-153, which are not present in the SCS/TNe Emulation with a specific font ID, are printed with the definition of font 86. Appendix - SCS TN5250eFont Table: Set Substituted Font ID 304 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 303
herein; these changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any time. © Copyright 2009 Lexmark International, Inc. © Copyright 2009 Kodak All rights reserved. Edition Notice: SCS/TNe Emulation User's Guide 305 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 304
or both. Intelligent Printer Data Stream and IPDS are trademarks or registered trademarks of Ricoh Co., Ltd in the United States, other countries, or both. Lexmark and Lexmark with diamond design, trademarks are the property of their respective owners. Trademarks: SCS/TNe Emulation User's Guide 306 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 305
Table of Contents Card for IPDS and SCS/TNe SCS/TNe Emulation User's Guide Getting Started ...1 SCS/TNe in a LAN environment ...1 Documentation Overview ...1 Equipment Requirements and Specifications ...2 Support ...4 Customer Support ...4 Important Configuration Basics ...5 Introduction ...5 What - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 306
Connection 51 Installation Setup for AS/400 and iSeries Users 53 Introduction ...53 Task 1 - Configuring the Job ...71 Important! ...71 Printer Cancel Job ...72 MFP Cancel Job ...74 Operations Reference - Common Setup ...75 Introduction ...75 Menu Options Overview ...77 Disconnect Ses ...78 Reset - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 307
Reset ALL Def ...82 Operations Reference - TN3270E SETUP 83 Introduction ...83 Overview ...102 COR/APO Sett (IDB Option 122) ...103 SCS Options > MISC SETTINGS Menu: Options Overview 104 FF Support (IDB Option 5) ...106 Non-Print Char (IDB Option 3) ...107 CSC Characters (IDB Options 8 & 9) - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 308
Option 167) ...122 Form Strings (IDB Option 168) ...123 IBM Trn Code (IDB Option 169 bit 1) ...124 Leadin Sequence (IDB Option 169 bit2) ...125 Euro Support (IDB Event 191) ...126 SCS Options> MISC SETTINGS > BOLD PRINT Menu - Options Overview 127 Bold On CR (IDB Option 22 bit 1) ...128 Bold On BS - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 309
(IDB Option 128) ...181 Move Hor/Ver (IDB Option 158) ...183 Format Ctrl Sup (IDB Option 177) ...185 Download Font (IDB Option 244) ...186 Euro Support (IDB Option 139) ...188 SCS OPTIONS > CSC CHARACTERS Menu: Options Overview 190 IDB First Char (IDB Option 8) ...191 IDB Second Char (IDB Option - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 310
Def Page Ori 1 (IDB Option 121) ...197 Def Page Ori 2 (IDB Option 122) ...198 COR Action 1 (IDB Option 123) ...199 COR Action 2 (IDB Option 124) ...201 PPM Quality Dis (IDB Opt.126) ...203 COR LSI Reduc (IDB Option 127) ...205 SCS OPTIONS > MISC SETTINGS Menu: Options Overview 206 Country Code (IDB - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 311
the IDB Configuration File ...255 Storing the IDB Configuration File ...256 Additional TN5250e Printer Commands Using IDB 258 Introduction ...258 Input Data String Syntax ...259 Initializing - Power On Initialize ...260 Paper Handling > Source Drawer ...262 Paper Handling > Destination Drawer - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 312
Specifications, Requirements, Features 275 Product Description ...275 Compatibility ...276 Print Platforms ...277 Features List: 3270 SCS ...278 Features List: 5250 SCS ...279 ASCII Character Table ...280 - Lexmark X860 | SCS/TNe Emulation User's Guide - Page 313
SCS/TNe Emulation User's Guide ...303 Trademarks ...304 ...304 Table of Contents ...305 : 313
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
 |
 |
1
Getting Started:
SCS/TNe in a LAN environment
Card for IPDS and SCS/TNe -
SCS/TNe Emulation User’s Guide
Getting Started
SCS/TNe in a
LAN
environment
Thank you for purchasing the Card for IPDS and SCS/TNe.
The card provides high quality IBM host connectivity print output.
With the appropriate print server and host software, your printer or
Multifunction Product (MFP) becomes an IBM host workstation
printer capable of printing IPDS or SCS documents from an iSeries,
AS/400, or mainframe. For a more detailed product description, see
“Specifications, Requirements, Features” on page 277
.
I
MPORTANT
:
Unless otherwise stated, the term
printer in this manual refers to both printers and
MFPs.
SCS data is received in a LAN environment using the Telnet
extended protocol. The Card for IPDS and SCS/TNe adds support
for the TN3270E and the TN5250E protocols. A correctly configured
printer can receive, process, and print SCS print jobs received over
TCP/IP.
Documentation
Overview
This document deals only with setting up and using the
SCS/TNe
emulation
in the Card for IPDS and SCS/TNe. It will help you to
understand, use, and change option settings for receiving SNA