LiftMaster GH GT- Logic 4 Installation Manual - Page 43
Accessories - price
View all LiftMaster GH manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 43 highlights
OPEN ACCESSORIES REMOTE CONTROLS 315MHz LiftMaster offers a variety of SECURITY✚® Remote Controls for your application needs. Single to 4-Button, visor or key chain. Contact your authorized dealer. ENTRAPMENT PROTECTION DEVICES MONITORED CPS-UN4 OPEN Commercial Protector System®: Provides protection on doors up to 45' wide. NEMA-4 rated. 371LM 373LM 1-Button SECURITY✚® Remote Control: Includes visor clip. 3-Button SECURITY✚® Remote Control: CPS-U OPEN Commercial Protector System®: Provides protection on doors up to 30' wide. 333LM WPB1LM3 OPEN WPB3LM3 Includes visor clip. 3-Button Tri-Colored Dip Switch Remote Control: Includes visor clip. Wireless Single Push Button Control SECURITY✚®: Rugged composite housing. (Wireless controls cannot be used in place of hard wired controls.) Wireless 3 Button Control Station SECURITY✚®: Rugged composite housing. (Wireless controls cannot be used in place of hard wired controls.) WKP5LM3 (5 4-digit entry codes) WKP250LM3 (250 4-digit entry codes) Wireless Access Control Keypads SECURITY✚®: 123 456 789 Rugged composite housing. (Wireless controls cannot be * 0# used in place of hard wired controls.) CONTROL STATIONS 02-101 1-Button Control Station: Steel enclosure. OPEN CPS3CARD Option Logic Board: For use when more than one set of photoelectric sensors are required. Also available pre-packaged with a second set of photoelectric sensors; see CPS3 or CPS3-N4 in Commercial Door Operator Product and Accessories Price List for more information. CPS-EI CPS-EI E1 LMEP2 E2 LMEP1 E3 E4 40-34141-1 65ME1234 65ME110 Monitored Safety Edge Interface: For use with the approved 4-wire safety edge (see below). Miller ME123 4-Wire Monitored Safety Edge: For sectional or rolling doors. Miller ME110 4-Wire Monitored Safety Edge: For rolling grilles and counter shutters. MOUNTING CHANNELS 65ME123C U-Shaped Mounting Channel: For 65ME1234 edge when installed on sectional doors. 65ME123C1 OPEN OPEN 65ME123CA3 T-Shaped Mounting Channel: For 65ME1234 edge when installed on rolling doors. Fits between L-shaped angles used to construct a bottom bar on rolling doors. L-Shaped Mounting Channel: 02-102 OPEN CLOSE 02-103L OPEN CLOSE STOP 02-110 OPEN CLOSE STOP 2-Button Control Station: Steel enclosure. 3-Button Control Station: Steel enclosure with Maintenance Alert System. Key Control Station: Indoor flush mount, NEMA 1 with Stop button. MOUNTING BRACKETS 10-12360 Heavy gauge steel bracket for vertical or horizontal mount on either front or top of coil on a rolling door. Has a variety of mounting hole patterns compatible with many OEM manufacturers. For use with J, H, DJ, and DH operators. May be welded. 08-9098 Cast iron bracket to mount J, H, DH, DJ, and GH side mount operators on end bracket of a rolling door or grill. For vertical or horizontal mount on either front or top of coil. Cannot be welded. 08-9098EZ Same as 08-9098, but with adapter plate to hold mounting bolts in place for easy mounting. For 65ME1234 edge when installed on sectional doors. 65-8202 65-5202 NON-MONITORED Vehicle Detection System: Pneumatic Sensing Edge Kit with exterior air switch, 2-wire coil cord and 14' air hose. Vehicle Detection System: Pneumatic Sensing Edge Kit with exterior air switch, 2-wire take-up reel (20' extended) and 14' air hose. OPTION CARDS TLS1CARD Timer Light Status Card: The TLS option card provides special functionality to activate and flash auxiliary devices such as lights, bells, and horns/strobes at various door positions, and to provide special timer functions. AUXCARD Auxiliary Contact Card: The Auxiliary Contact option card has both Normally-Open and Normally-Closed contacts that actuate when the door is idle, opening, or closing. CHAIN TENSIONERS For Jackshaft Type Operators 71-6023 For 1" shafts. Recommended to properly tension drive chain between operator shaft and door shaft. 71-6125 Same as 71-6023, but for 1-1/4" shafts. 1A4324 Heavy gauge steel bracket for vertical or horizontal mount on either front or top of coil on a rolling door. May be welded. For use with J, H, DJ, and DH operators. 1A4324EZ Same as 1A4324, but with adapter plate to hold mounting bolts in place for easy mounting. MISCELLANEOUS 1A3982 Operator Cover: 86LM (15') 86LMT (25') For use with wall-mounted J, H, GH, DH or DJ operators. Measures 31" x 19" x 18" (L x W x D). Assembly required. Recommended for damp environments where direct spray is present. Required when the operator is installed less than 8 feet above the floor. Antenna Extension Kit: Accessories The antenna extension kit can be used with EXT-ANT for maximum radio receiver range. 43 ACCESSORIES