LiftMaster LA400 LA400 Manual - Page 35

Programming - replacement parts

Get LiftMaster LA400 PDF manuals and user guides
UPC - 753182403953
View all LiftMaster LA400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

PROGRAMMING » REMOTE CONTROLS + KEYLESS ENTRY + ERASE ALL CODES + TEST A combined total of 50 remote controls and keyless entry PIN can be programmed to the operator. For highest level of security, we recommend the Security✚® line of products. Refer to Accessories. TO ADD OR REPROGRAM A REMOTE CONTROL (NOT PROVIDED) 1 Remote Control LEARN XMITTER Button 1 Press LEARN XMITTER button and release (LED will light up). LEARN XMITTER K5 2 Press the remote control button. The LED will flash and the alarm output will activate twice. LEARN R1 XMITTER 2 To program additional remote controls, repeat steps until all remote controls are programmed. TO ADD A WIRELESS KEYLESS ENTRY (NOT PROVIDED) 1 Press LEARN XMITTER button and release (LED will light up). 2 Enter a 4-digit personal identification number (PIN) of your choice on the keypad. 1 Remote Control LEARN XMITTER Button LEARN XMITTER K5 LEARN R1 XMITTER 2 3 Press the ENTER button on the keypad. The LED will flash and the alarm output will activate twice. ???? PIN Number TO ERASE ALL CODES 1 Press and hold the LEARN XMITTER button on control board until the learn indicator light goes out (approximately 6 seconds). All previous codes are now erased. NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. TEST After any adjustments are made, test the operator: 1 Use the Single Button Control (SBC) button to open and close the gate. 2 Test the limits by making sure the gate is stopping at the OPEN and CLOSE limits. 3 Test the force by making sure the gate will stop and reverse on contact with an obstruction. 34 1 Remote Control LEARN XMITTER Button LEARN XMITTER K5 LEARN R1 XMITTER

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
R1
34
TO ADD OR REPROGRAM A REMOTE CONTROL
(NOT PROVIDED)
Press
LEARN XMITTER
button and release (LED will light up).
Press the remote control button. The LED will flash and the alarm output will
activate twice.
To program additional remote controls, repeat steps until all remote controls are
programmed.
TO ERASE ALL CODES
Press and hold the
LEARN XMITTER
button on control board until the learn
indicator light goes out (approximately 6 seconds). All previous codes are now
erased.
Remote Control LEARN XMITTER Button
PROGRAMMING
» REMOTE CONTROLS + KEYLESS ENTRY + ERASE ALL CODES + TEST
2
1
1
2
1
R1
Remote Control LEARN XMITTER Button
1
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are
prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
LEARN
XMITTER
LEARN
XMITTER
TO ADD A WIRELESS KEYLESS ENTRY
(NOT PROVIDED)
Press
LEARN XMITTER
button and release (LED will light up).
Enter a 4-digit personal identification number (PIN) of your choice on the
keypad.
Press the ENTER button on the keypad. The LED will flash and the alarm output
will activate twice.
PIN Number
?
?
?
?
2
1
2
3
R1
Remote Control LEARN XMITTER Button
1
LEARN
XMITTER
TEST
After any adjustments are made, test the operator:
Use the Single Button Control (SBC) button to open and close the gate.
Test the limits by making sure the gate is stopping at the OPEN and CLOSE
limits.
Test the force by making sure the gate will stop and reverse on contact with an
obstruction.
1
2
3
A combined total of 50 remote controls and keyless entry PIN can be programmed to
the operator. For highest level of security, we recommend the Security
✚
®
line of
products. Refer to Accessories.