LiftMaster Passport PASSPORT Manual
LiftMaster Passport Manual
 |
View all LiftMaster Passport manuals
Add to My Manuals
Save this manual to your list of manuals |
LiftMaster Passport manual content summary:
- LiftMaster Passport | PASSPORT Manual - Page 1
390 MHz Wiegand Receiver with Passport Technology SPECIFICATIONS Power: 12VDC, 50 mA Temperature Rating: -40° to +185° F Model CPWR3 RF Frequency: 390 MHZ Accessory Transmitters Visors: CPT1, CPT2, CPT3, CPT4 Key chains: CPTK1, CPTK3, CPTK1PH, CPTK3PH OVERVIEW The Wiegand Receiver (CPWR) is - LiftMaster Passport | PASSPORT Manual - Page 2
• To disallow receiver response to transmitter buttons, move the DIP switch(es) to the LEFT. All button switches are factory set to ON. Switch S1, 1 controls Button #1 and Button #4* Switch S1, 2 controls Button #2 Switch S1, 3 controls Button #3 * If using a CPT4 transmitter, Button #4 reacts - LiftMaster Passport | PASSPORT Manual - Page 3
board. Connect wires from the CPWR 6-pin connector to the access control system (Figure 8). Then re-insert the terminal block onto J2. Wire the CPWR to the access control systems' card reader port. Refer to the access control system's instructions for appropriate wiring detail. A typical wire - LiftMaster Passport | PASSPORT Manual - Page 4
. DATA - Yellow This LED indicates that the receiver recognizes the transmission data as coming from a Chamberlain® transmitter with Passport technology. VALID - Green This LED indicates that the receiver is sending a Wiegand format output to the access control system. POWER - Red This LED indicates - LiftMaster Passport | PASSPORT Manual - Page 5
APPENDIX: FACILITY CODE SWITCH SETTINGS Refer to Figure 1 on page 1 for the facility code DIP switch location. Also, when setting the receiver's DIP switches, refer only to the numbers silk screened on the PC board (not the numbers on the DIP switch itself). FC 000 001 002 - LiftMaster Passport | PASSPORT Manual - Page 6
all equipment; this warranty is not effective until such payment in full has been received. The warranty period shown above applies only to the LiftMaster receiver with Passport technology). Since this is a manufacturer's warranty, not a dealer's warranty, installation, removal, and freight charges
-
1 -
2 -
3 -
4 -
5 -
6
 |
 |
1
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is not connected BEFORE installing the
receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote
control transmitters.
• Activate gate or door ONLY when it can be seen clearly,
is properly adjusted, and there are no obstructions to
door travel.
• ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate
or door.
SPECIFICATIONS
Power:
12VDC, 50 mA
Temperature Rating:
-40° to +185° F
Model CPWR3 RF Frequency:
390 MHZ
Accessory Transmitters
Visors:
CPT1, CPT2, CPT3, CPT4
Key chains:
CPTK1, CPTK3, CPTK1PH, CPTK3PH
OVERVIEW
The Wiegand Receiver (CPWR) is a communication device that
transmits an information packet to an access control unit such as
a Sentex Telephone Entry System. All receiver units utilize the
latest in Chamberlain
®
rolling code technology.
ACCESS CONTROL COMPATIBILITY
The CPWR outputs a 26-bit or 30-bit Wiegand format compatible
with Sentex access control systems.
CARTON INVENTORY
Wiegand Receiver
Antenna
Instructions
PARTS NOT PROVIDED
# 6 Mounting Hardware
5-conductor shielded cable; 22 AWG wire
Extension Kit (Optional)
MODEL CPWR
390 MHz Wiegand Receiver with
Passport Technology