LiftMaster RSW12V RSW12V Install Manual
LiftMaster RSW12V Manual
 |
View all LiftMaster RSW12V manuals
Add to My Manuals
Save this manual to your list of manuals |
LiftMaster RSW12V manual content summary:
- LiftMaster RSW12V | RSW12V Install Manual - Page 1
look different than the model illustrated in this manual. STOP IMPORTANT NOTE: The gate operation may be limited until the battery is fully charged. THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. Visit www.liftmaster.com to locate a professional installing - LiftMaster RSW12V | RSW12V Install Manual - Page 2
14 15-16 16 17 OPERATION AND MAINTENANCE Manual Disconnect Reset Button Remote Control Sleep Mode Maintenance Battery TROUBLESHOOTING Diagnostic Error Codes Chart Troubleshooting Chart Wiring Diagram 18-23 ACCESSORIES 18-22 23 WARRANTY 23 SAFETY » SAFETY SYMBOL AND SIGNAL WORD REVIEW When you see - LiftMaster RSW12V | RSW12V Install Manual - Page 3
or other building servicing the general public. UL325 ENTRAPMENT PROTECTION REQUIREMENTS This chart illustrates the entrapment protection requirements for the UL325 classes. GATE OPERATOR ENTRAPMENT PROTECTION UL325 Classification CLASS I CLASS II Swing Gate Operator Primary Type Secondary - LiftMaster RSW12V | RSW12V Install Manual - Page 4
. Swinging gates shall not open into public access areas. 7. The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. 8. Controls intended for user activation must be located at least 6 feet (1.8 m) away from any moving part of the gate - LiftMaster RSW12V | RSW12V Install Manual - Page 5
automated gate, when the operator requires replacement, shall be upgraded to conform to the provisions of this specification in effect at that time. entrapment area between the gate and the supporting structure or other fixed object when the gate moves toward the fully open position, subject - LiftMaster RSW12V | RSW12V Install Manual - Page 6
. The safety loops allow the gate to stay open when vehicles are obstructing the gate path. Suggested for vehicles 14 feet (4.27 m) or longer. Safety loops are not required safety devices but are recommended. NON-CONTACT SENSORS Use photoelectric sensor model 50-220. Inside PIrnospiedretyLSoaofepty - LiftMaster RSW12V | RSW12V Install Manual - Page 7
access through openings anywhere the gate may travel. • Mount controls at least 6 feet (1.8 m) from the gate or ANY moving part of the gate. • Install Warning signs on EACH side of gate in PLAIN VIEW. Permanently secure each Warning sign in a suitable manner using fastening holes. • This operator is - LiftMaster RSW12V | RSW12V Install Manual - Page 8
gate operator properly can increase the risk of INJURY or DEATH. • Use the emergency release ONLY when the gate is not moving. • KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a qualified service person make repairs to gate hardware. • ALL maintenance MUST be performed by a LiftMaster - LiftMaster RSW12V | RSW12V Install Manual - Page 9
HARDWARE INVENTORY OPERATOR SPECIFICATIONS This model is intended for use in vehicular swing gate applications: Gate Classifications: : Solar Power Max: Maximum Gate Weight/Length: Daily Cycle Rate using transformer power: Maximum Gate Travel Range: Temperature: Control Board Fuse: CLASS I & II - LiftMaster RSW12V | RSW12V Install Manual - Page 10
when installing this gate operator, such as gate size and site layout. The following instructions and illustrations should be used as a general guide so please note a compact installation. If the operator arm will hit an obstruction when the gate is in the open position follow the directions for - LiftMaster RSW12V | RSW12V Install Manual - Page 11
1/2" 6" Above Ground 30" Below Ground MOUNTING FOOTPRINT 14" 12.2" 13.6" 17" NOTE: An alternative to a concrete pad is to post mount the operator (refer to accessories). Concrete Pad 28" 24" SAMPLE STANDARD INSTALLATION Hinge Center OUT 26" Post IN 2" 25" 35.5" 14" Long Arm 10" 29 - LiftMaster RSW12V | RSW12V Install Manual - Page 12
are from the center of one pivot point to the center of another pivot point. Caution: If the gate is longer than 18 feet, follow CHART A: A-2. Suggestion: The dimensions between the gate and the concrete pad is always 10 inches less than the dimension D. Example: D = 42", if the dimensions between - LiftMaster RSW12V | RSW12V Install Manual - Page 13
PAD AND OPERATOR DO NOT run the operator until instructed. Refer to the illustration to determine the measurements and location of the concrete pad. NOTE: When lifting the operator use the handle to avoid damaging the operator. TOP VIEW OF OPERATOR AND GATE Gate Hinge Center Gate Open 90° 26 - LiftMaster RSW12V | RSW12V Install Manual - Page 14
4" 20" 3 23" 25-1/2" POSITION THE GATE BRACKET NOTE: It may be necessary to attach horizontal reinforcement to the gate before attaching the gate bracket. 1 Measure 33 inches from the gate hinge center. 2 Make sure the operator arm is level and tack weld the gate bracket in this position. 1 33 - LiftMaster RSW12V | RSW12V Install Manual - Page 15
it with a single wire length. NOTE: If the operator is not grounded properly the range of the remote controls will be reduced. 1 Install the earth ground rod within 3 feet of the operator. 2 Attach the ground wire to the ground terminal on the control board. 14 OVLD AC PWR /SOLAR 2 12 gauge copper - LiftMaster RSW12V | RSW12V Install Manual - Page 16
operator reviewed for suitability of wire installation. 1 Remove the access panel. 2 Connect AC power to the operator NOTE: If your operator comes with a on the control board. 5 Plug reviewed operator. 2 Connect the wires from the transformer to the AC PWR/SOLAR terminal located on the control board - LiftMaster RSW12V | RSW12V Install Manual - Page 17
BEFORE servicing the operator. NOTE: Setting the battery on concrete will not have a negative affect on the charging or battery life. If the installation is a dual gate, proceed to next page. 1 Locate the battery plug. 2 Connect the battery plug to either connector on the control board. Connector - LiftMaster RSW12V | RSW12V Install Manual - Page 18
the other (an ornamental overhang, maglock or solenoid lock) consider which gate needs to open/close first and plan accordingly. The gate that opens first MUST be the primary operator (GATE 1). The control board in the secondary operator is not used. 1 Trench across driveway to bury the extension - LiftMaster RSW12V | RSW12V Install Manual - Page 19
open position and the fully closed position. For proper functionality, the limits must be programmed during the installation process. The programming uses a combination of buttons on the control board. The specific buttons used for programming depends on which side of the gate the primary operator - LiftMaster RSW12V | RSW12V Install Manual - Page 20
limit switch. PROGRAM OPEN 2 Manually open the gate to the desired open position. 2 3 Tighten the handle on the operator arm. 4 Press and release the LEARN LIMITS BUTTON. The SET OPEN LIMIT LED will blink. 5 Press and release the LEARN LIMITS button again. The control board will beep and the - LiftMaster RSW12V | RSW12V Install Manual - Page 21
the learn limit switch. PROGRAM OPEN 2 Manually open the gate to the desired open position. 3 Tighten the handle on the operator arm. 4 Press and release the LEARN LIMITS BUTTON. The SET OPEN LIMIT LED will blink. 5 Press and release the LEARN LIMITS button again. The control board will beep and the - LiftMaster RSW12V | RSW12V Install Manual - Page 22
to blink, repeat programming. If the problem continues, see below. Test the limits by pressing the SINGLE BUTTON to open and close the gate. IF THE LIMITS WILL NOT PROGRAM 1 Disconnect the operator by releasing the handle on the operator arm. 2 Manually close the gate. 3 Loosen the screw on the - LiftMaster RSW12V | RSW12V Install Manual - Page 23
to blink, repeat programming. If the problem continues, see below. Test the limits by pressing the SINGLE BUTTON to open and close the gate. IF THE LIMITS WILL NOT PROGRAM 1 Disconnect the operator by releasing the handle on the operator arm. 2 Manually close the gate. 3 Loosen the screw on the - LiftMaster RSW12V | RSW12V Install Manual - Page 24
seasonal adjustment may be required. The force control is factory set to the mid-position. TEST After any adjustments are made, test the operator: 1 Use the SINGLE BUTTON to open and close the gate. 2 Test the limits by making sure the gate is stopping at the OPEN and CLOSE limits. 3 Test the force - LiftMaster RSW12V | RSW12V Install Manual - Page 25
USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is operation. ALTERNATE RADIO RECEIVER INSTALLATION 1 The receiver should be connected to the SINGLE BUTTON input and the CTRL PWR input. 24 LEARN 1 XMITTER OPEN CONTROL INPUTS SINGLE BUTTON RESET - LiftMaster RSW12V | RSW12V Install Manual - Page 26
is enabled and you would like the gate to remain open, open the gate fully, then press the reset button. The next command given by a LiftMaster remote control or SINGLE BUTTON on the control board will close the gate and return the operator to normal operation. NOTE: If an alternative radio receiver - LiftMaster RSW12V | RSW12V Install Manual - Page 27
5 minutes) and the operator will have to be reset before it will resume normal operation. NON-CONTACT SENSORS (12 VDC PHOTOELECTRIC SENSORS) Photoelectric sensor model 50-220. 1 Connect the non-contact sensor wires to either the OPEN PHOTO or CLOSE PHOTO terminal on the control board. It is best to - LiftMaster RSW12V | RSW12V Install Manual - Page 28
AND MAINTENANCE » MANUAL DISCONNECT + RESET BUTTON + REMOTE CONTROL + SLEEP MODE MANUAL DISCONNECT Release the handle on the operator arm to allow the gate to be opened and closed manually. On a dual gate application the handle must be released on both operators. To resume normal function tighten - LiftMaster RSW12V | RSW12V Install Manual - Page 29
all power to the operator before servicing. DESCRIPTION External Entrapment Protection System Photoelectric Sensors Warning Signs Manual Disconnect Sprockets and Chains Gate Accessories Electrical Chassis Mounting Bolts Operator Batteries TASK Check and test for proper operation Check and test for - LiftMaster RSW12V | RSW12V Install Manual - Page 30
• Check to make sure the jumper wire is connected between the COM and STOP input on the control board. Stop is an NC (normally closed) input. 3 FLASHES LOW BATTERY VOLTAGE Battery voltage is below the recommended operating level. • Battery may not be properly charged. Disconnect all batteries and - LiftMaster RSW12V | RSW12V Install Manual - Page 31
that the gate(s) swing easily. Lubricate or replace hinges as necessary. • Check the brown and green wires on J17 to ensure they are properly connected. If this did not solve the problem the RPM Module or control board may need to be replaced. Contact technical support. OPERATOR DOES NOT RESPOND - LiftMaster RSW12V | RSW12V Install Manual - Page 32
Accessory) Entry system output is connected to the OPEN input, and is "stuck" opening. Verify entry system connections and operation. • Operator in Party mode after RESET button pressed while at the OPEN limit. Use a remote or the SINGLE BUTTON to close the gate and reopen it. Verify that the TIMER - LiftMaster RSW12V | RSW12V Install Manual - Page 33
- LiftMaster RSW12V | RSW12V Install Manual - Page 34
upon contact and stop the operator. Models G65MG0204, G65MG0205, G65MGR205, and G65MGS205 SENSING EDGE CHANNEL Mounting channel for all MG020 type edges. Model G65ME120C5 REMOTE CONTROLS Chamberlain offers a variety of LiftMaster Security✚® and Passport™ remote controls to satisfy your application - LiftMaster RSW12V | RSW12V Install Manual - Page 35
receiver for up to 450 Security✚® remote controls. Model STAR450-315 HEATER Keeps operator, gearbox and batteries at suitable temperature when outside temperature is below 0°F for extended periods of time. Models HTRKITRSW (for Swing operator, includes bracket for optimal heater location) and - LiftMaster RSW12V | RSW12V Install Manual - Page 36
, call 1-800-528-2806, toll free, before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair. You will be advised of shipping instructions when you call. Please include a brief description of the problem and a dated proof-of purchase
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
 |
 |
RSW12V
™
&
RSW12VH
™
VEHICULAR SWING GATE OPERATOR
I N S T A L L A T I O N
M A N U A L
SOLAR
CAPABLE
SEE ACCESSORIES.
SOLAR
CAPABLE
UL325
compliant
UL991
compliant
This model is for use on vehicular
passage gates ONLY and not intended
for use on pedestrian passage gates.
This model is intended for use in
Class I and Class II vehicular swing
gate applications.
Your model may look different than the model illustrated in this manual.
IMPORTANT NOTE:
The gate operation may be
limited until the battery is fully charged.
STOP
THIS PRODUCT IS TO BE
INSTALLED AND SERVICED BY
A TRAINED GATE SYSTEMS
TECHNICIAN ONLY.
Visit www.liftmaster.com to
locate a professional installing
dealer in your area.