LiftMaster SL585UL SL585UL SL595UL Three Phase Wiring Diagram

THREE PHASE WIRING DIAGRAM

Models SL585UL and SL595UL

TRANSFORMER

J14

J11

J12

LINE IN

J1

L1

J2

L2

J3

L3

J7

COMM

WHITE

(BLACK)

(WHITE)

(PURPLE)

208V

RED

240/575V

ORANGE

480V

PURPLE

J9

J5

J4

J6

MOTOR

CURRENT

480V

BRAKE

240V/208V

575V

J8

J10

12V

12V

24V

TRANSFORMER

J14

J11

J12

LINE IN

J1

L1

J2

L2

J3

L3

J7

COMM

WHITE

(BLACK)

(WHITE)

(PURPLE)

208V

RED

240/575V

ORANGE

480V

PURPLE

J9

J5

J4

J6

MOTOR

CURRENT

480V

BRAKE

240V/208V

575V

J8

J10

12V

12V

24V

COMM

LINK

B

A

ANTENNA

CURRENT

SENSOR

MOTOR DRIVE

RPM & LIMITS

ALARM

EXP.

BOARD

24 VAC IN

CLASS 2 SUPPLY

24 VDC

500 mA MAX

ID RESET

GND

BIPART

DELAY

2

4

6

8

OPEN

LEFT

OPEN

RIGHT

COMM

LINK

B

A

CLASS 2 SUPPLY

24 VDC

500 mA MAX

N.O.

COM

C

NO

NC

4

3

2

1

C

NO

NC

RPM & LIMITS

ALA

SET

87654321

9

CURRENT

SENSOR

MOTOR DRIVE

RPM & LIMITS

ALARM

EXP.

BOARD

24 VAC IN

ID RESET

GND

8

7654321

21

4 3 21

4

3

2

1

4321

78 9

6

5

4

3

2

1

21

1

2

9

10

1

3

15

COM

120

240

460

208

HANDING

1

2

3

COM

120

480

575

240

13

12

13

14

15

11

10

9

8

7

6

5

4

3

2

1

T3

T6

T9

T7

T8

T5

T4

T1

T2

T1

T8

T7

T3

T4

T5

T9

T6

TP

TP

T2

J13

4321

RESET

BUTTON

PRODUCT ID

CONTROL BOARD

ANTENNA

N.C.

INTERRUPT LOOP

or

PHOTOELECTRIC SENSORS

for CLOSE cycle

EDGE SENSOR

for CLOSE cycle

SHADOW LOOP

EXIT LOOP

EXIT

OPTIONAL ACCESSORY

WIRING

ACCESSORY POWER

24VAC 2.2 AMPS MAX

FIRE DEPARTMENT

ACCESS CONTROL

DEVICE

3-BUTTON CONTROL STATION

MAGLOCK

(Optional)

SOLENOID LOCK

(Optional)

OR

OR

Shielded Twisted Pair Cable

(Primary/Secondary link to other

gate operator) Ground the shield of

the cable to the chassis ground of

each operator.

ACCESSORY POWER

24 Vdc 500 mA Maximum

(Not Provided)


for OPEN cycle

or

EDGE SENSOR

(Not Provided)

Jumper

ALARM

Black

White

White

Orange

Purple

Gray

Green

Blue

Red

Purple

White

SL585UL - Blue

SL595UL - Black

White

Orange

Red

Black

Red

TRANSFORMER

These switches determine if the corresponding

photoelectric sensor or edge sensor will function

for the OPEN or CLOSE cycle.

PLUG-IN LOOP DETECTOR

Model LOOPDETLM

EXPANSION BOARD

N.C.

SHADOW LOOP

EXIT LOOP

INTERRUPT LOOP

AUXILIARY

RELAY 2

AUXILIARY

RELAY 1

These switches control how the Auxiliary Relays will function.

Jumper

SINGLE BUTTON CONTROL STATION

3-BUTTON CONTROL

STATION


WIRELESS EDGE KIT

Model LMWEKITU


or

EDGE SENSORS

L1 Black

Black

POWER BOARD

Three Phase

POWER BOARD

THREE PHASE

Power Wiring

480 Vac Power Wiring

with Heater

CLOSE

Limit Switch

OPEN

Limit Switch

Limit Switch Wiring

CONTROL BOARD

Black

Blue

Black

Yellow

Black

Green

Red

Black

Yellow

Blue

Blue

Red

JUNCTION BOX

FOR 480 VAC USE STEP DOWN

TRANSFORMER (Model HTR460)

L2 White

White

HEATER (Model HTRNB)

(Optional Accessory)

Normally Open

Common

Normally Closed

Normally Open

Common

Normally Closed

Yellow

Yellow

Yellow

Green

White

Black

Red

HEATER

(Optional Accessory,

Model HTR460

)

White

Black

Black

Red

Red

SWITCH SETTINGS

1

2

3

RELAY 1

RELAY 2

OFF

Relay always off

Relay always off

OFF

OFF

OFF

OFF

ON

Energizes at open limit

Energizes at open limit

OFF

OFF

ON

Energizes when not at

close limit

Energizes when not at

close limit

OFF

ON

ON

Energizes when motor is on

Energizes when motor is on

ON

OFF

OFF

Energizes 3 seconds prior

and during gate motion

Energizes 3 seconds prior

and during gate motion

ON

OFF

ON

Not used

Not used

ON

OFF

OFF

Energizes when gate is

tampered with

Energizes when gate is

tampered with

ON

ON

ON

LEDs will blink cycle count

Not used

RED

/

GREEN

LIGHT FUNCTIONALITY

1

2

3

Red light

wired to AUX RELAY 1.

Green light

wired to AUX RELAY 2.

AUX RELAY 1 SWITCHES

OFF

Red light OFF*

OFF

OFF

CLOSED

GATE STATE

AUX RELAY 2 SWITCHES

Green light OFF

1

2

3

ON

ON

ON

OPENING

OPEN

CLOSING

Defined Mid Stop

Undefined Mid

Stop

Timer more than

5 seconds

Timer less than

5 seconds

* For red light ON when gate is closed, set switch 1 on AUX RELAY 1 to ON

Red light ON/FLASH

Red light OFF

Red light ON/FLASH

n/a

Red light ON

Red light OFF

Red light ON/FLASH

Green light OFF

Green light ON

Green light OFF

Green light OFF

n/a

Green light OFF

Green light ON

Yellow

Blue

Yellow

Blue

MOTOR

HARNESS

To configure the motor for

208V, swap the orange and

red wires and plug motor

into the 208V / 240V position.

SOLENOID BRAKE

THREE PHASE

MOTOR

RPM BOARD

Blue

Yellow

Yellow/Black

Orange

Brown

Gray

White

Red

Purple

Purple

Yellow/Black

Purple

Purple

Purple

Black

24 VAC

3.15A FUSE

MOV ASSEMBLY

Connected across J1, J2, J3

HORSE POWER ID

1/2 HP - Yellow

1 HP - Purple

2 HP - Black

24 VAC

L3 Purple

Purple

N.C.

N.C.

N.C.

INCOMING POWER

SWITCH

NOTE:

Heater is rated for

240 VAC maximum.

Attach

to metal

chassis

NOTE:

The switch is

located in the electrical

box for Model SL595.

SWITCH

LOCKS

ACCESSORY

POWER

DUAL

GATES

ENTRAPMENT

PROTECTION

LOOPS

CONTROLS

LiftMaster.com

© 2018, LiftMaster

All Rights Reserved

01-39240-7

Press and hold

STOP...

...then press and

hold CLOSE...

...then press and hold OPEN

until "Er" shows.

CODE SEQUENCE NUMBER

The first number shown is the most recent

code (example: “01”). The display will show

the sequence of codes that occurred starting

with “01” and going up to code “20”.

CODE NUMBER

The second number shown after the code

sequence number is the code itself

(31-99, example” “31”).

A SECOND LATER

....

The operator will show the code sequence number followed by the code number:

Diagnostic Codes

TO VIEW THE CODES:

LiftMaster System

Installed System

Informational

External Entrapment Protection

Inherent Entrapment Protection

CODE COLOR KEY:

MEANING

SOLUTION

31

Main control board has

experienced an internal

failure.

Disconnect all power, wait 15 seconds, then reconnect power

(reboot). If issue continues, replace main control board.

35

Max-Run-Time Exceeded

Error

Attempt to run and review for duration and obstructions.

Max-Run-Time can be re-measured by saving one or both of

the limits again.

36

Product ID Error

Was the control board just replaced? If so, erase limits, enter

limit setup mode and set limits. If not, disconnect all power,

wait 15 seconds, then reconnect power before changing

product ID harness.

37

Product ID Failure

Unplug product ID harness then plug back in. Disconnect all

power, wait 15 seconds, then reconnect power before

replacing product ID harness.

43

Failure or missing EXIT loop

Check loop wiring throughout connection. May be a short in

the loop, or an open connection in the loop (LiftMaster Plug-

in Loop Detector only).

44

Failure or missing SHADOW

loop

45

Failure or missing

INTERRUPT loop

46

Wireless edge battery low

Replace batteries in wireless edge.

47

Power board fault

Relay fault detected in the power board. Replace the power

board.

50

Run-Distance Error

Limits are less than 4 feet apart or longer than what was

learned. Check limit positions and proper switch function.

Run-distance can be re-learned by setting the handing again.

53

Brownout occurred

AC/DC board supply dipped below allowable level. Review

power supply and wiring. If rebooting, ensure enough time

for discharge of power to force a fresh boot.

54

Wireless Second Operator

Communication Error

Check the second operator for power. If OFF, restore power

and try to run the system. If powered, deactivate the wireless

feature and then re-learn the second operator.

55

System AC Overvoltage

Call utility.

56

System AC Undervoltage

Check wiring and wire gauge to operator.

57

Limit Error - Stuck Switch

Check switch for proper operation. Check harness for shorts.

Replace if defective.

58

Limit Error - Wrong Switch

Check motor wiring.

59

Missing Power Board

Check harness for shorts. Check for presence of power

board.

60

Minimum number of

monitored entrapment

protection devices not

installed.

Review monitored entrapment protection device connections.

Slide gate operators require a minimum of two external

safety devices; one in the close and one in the open

direction.

61

CLOSE EYE/INTERRUPT held

more than 3 minutes

Check wired input on main board; check for alignment or

obstruction.

62

CLOSE EDGE held more than

3 minutes

63

OPEN EYE/EDGE held more

than 3 minutes

64

CLOSE EYE/INTERRUPT held

more than 3 minutes

Check wired input on expansion board; check for alignment

or obstruction.

65

CLOSE EYE/EDGE held more

than 3 minutes

66

OPEN EYE/EDGE held more

than 3 minutes

67

Wireless edge triggered more

than 3 minutes

Check wired input for wiring issue or obstruction.

68

Wireless edge loss of

monitoring

Check wireless edge inputs.

69

Wireless edge triggered

IF an obstruction occurred, no action required. If an

obstruction did NOT occur, check inputs and wiring.

70

CLOSE EYE/INTERRUPT

triggered, causing reversal,

preventing close, or resetting

TTC


obstruction did NOT occur, check alignment, inputs, and

wiring on main board.

71

CLOSE EDGE triggered,

causing reversal, preventing

close, or canceling TTC

72

OPEN EYE/EDGE triggered,

causing reversal or

preventing opening

73

CLOSE EYE/INTERRUPT

triggered, causing reversal,

preventing close, or resetting

TTC


obstruction did NOT occur, check alignment, inputs, and

wiring on expansion board.

74

CLOSE EYE/EDGE triggered,

causing reversal and

preventing close or canceling

TTC

75

OPEN EYE/EDGE triggered,

causing reversal or

preventing opening

80

Close input (EYE/EDGE)

communication fault from

other operator

Check inputs and communication method between operators,

either wired bus or radio. Ensure operator is powered. May

have to erase the wireless communication and reprogram the

two operators.

81

Open input (EYE/EDGE)

communication fault from

other operator

82

Close input (EYE/EDGE)

communication fault

(expansion board)

Check the connections between the main board and the

expansion board.

83

Open input (EYE/EDGE)

communication fault

(expansion board)

84

Non-monitored device

detected on the wireless

safety system

Make sure the attached edge/eye is monitored. Non-

monitored contact closure devices are not supported. For

edges, check the proper orientation and connection of the

resistive end cap.

91

Force Reversal

Look for obstruction, if no obstruction, check that the

mechanical assembly is engaged and free to move. Refer to

manual for Limit and Force Adjustment, and Obstruction

Test.

93

RPM / STALL Reversal

Check for obstruction. If no obstruction, check the operator

cable wiring and that the operator arm is engaged and free to

move. Replace RPM assembly.

95

AC motor no start condition

Motor failed to start. Check for an obstructed gate or binding

mechanism. Check start capacitor connections and condition.

99

Normal Operation

No action required

TO SCROLL THROUGH THE SAVED CODES:

Press the OPEN button to cycle to the most recent code ("01"). Press the CLOSE button

to cycle to the oldest code (up to “20”).

To reduce the risk of INJURY or DEATH:

•

DISCONNECT power BEFORE installing or servicing operator.

•

Replace ONLY with fuse of same type and rating.

•

To be compliant with UL325 and industry safety guidelines, qualified monitored

external entrapment protection devices such as photoelectric sensors or edge

sensors are required to be installed with this operator at each entrapment zone.

Use ONLY LiftMaster approved entrapment protection devices (refer to the

accessory page of manual).

•

See manual prior to servicing regarding maintenance and required safety testing.

LiftMaster SL585UL SL585UL SL595UL Three Phase Wiring Diagram

LiftMaster SL585UL Manual

LiftMaster SL585UL manual content summary: