Lowrance HDS-12 Carbon - No Transducer Installation Manual
Lowrance HDS-12 Carbon - No Transducer Manual
View all Lowrance HDS-12 Carbon - No Transducer manuals
Add to My Manuals
Save this manual to your list of manuals |
Lowrance HDS-12 Carbon - No Transducer manual content summary:
- Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 1
HDS Carbon Installation Manual ENGLISH www.lowrance.com - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 2
- Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 3
SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW. Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) may - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 4
the Radio communications (Electromagnetic Compatibility) standard 2008 • Part section at the following website: www.lowrance.com. Industry Canada IC RSS-GEN, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 5
amount of data you transfer. If you are unsure, contact your service provider to confirm rates and restrictions. Countries of intended use in the EU AT - Austria BE - Belgium BG - Liechtenstein LT - Lithuania LU - Luxembourg MT - Malta NL - Netherlands Preface | HDS Carbon Installation Manual 5 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 6
- Sweden CH - Switzerland TR - Turkey UK - United Kingdom Trademarks Lowrance® and Navico® are registered trademarks of Navico. Navico® is a registered registered trademark of Bluetooth SIG, Inc. Navico product references This manual refers to the following Navico products: • Broadband Sounder™ - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 7
About this manual This manual is a reference guide for installing HDS Carbon units. Important text that requires special attention from the reader is emphasized as follows: Ú Note: Used to draw the reader's attention to a comment or some important information. Warning: Used when it is necessary to - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 8
8 Preface | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 9
Transducer connection 27 Ethernet connector 28 NMEA 2000 device connection 30 NMEA 0183 device connection 31 Video in 33 Software Setup 33 First time startup 33 Time and Date 34 Data source selection 35 Device list 37 Diagnostics 38 Damping 38 Sonar setup Contents | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 10
69 Software updates and data backup 73 Dimensional drawings 73 HDS 7 Carbon 73 HDS 9 Carbon 74 HDS 12 Carbon 74 HDS 16 Carbon 75 Accessories 75 NMEA 2000 75 Display accessories 76 Ethernet cables 76 Other accessories 77 Sonar accessories 78 Supported data 78 NMEA 2000 compliant PGN List 81 NMEA 0183 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 11
4 Knobs 5 Fasteners (4x 6G x 1.5 panhead PH1) 6 Power/NMEA 0183 cable 7 Fuse holder (ATC blade) 8 Fuse (5 A) 9 Caps (3x for HDS-7, 4x for HDS-9/12/16 - for ethernet, NMEA 2000, StructureScan) 10 Documentation pack 11 Dash gasket (HDS-16 only) Check the contents | HDS Carbon Installation Manual 11 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 12
vessel with the supplied mounting bracket, or panel mounted. The unit is intended for 12 V DC operation and will accept the moderate fluctuations commonly seen in DC systems. The front panel and keys 2 3 4 5 8 1 6 9 7 10 11 12 1 Touchscreen 12 Overview | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 13
active panel/ overlay. Press and hold to hide or show the menu. A quick double-press displays the settings Press to select or save your settings. 9 Panel key Used on multiple-panel pages. A short press switches between the panels 12 microSD Card readers Overview | HDS Carbon Installation Manual 13 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 14
connections HDS Carbon rear connections HDS-9/12/16 HDS-7 1 2 2 3 4 5 214 53 1 NMEA 2000 - data input / output 2 ETHERNET - high bandwidth data (radar, sonar, chart) 3 POWER - 12V input & NMEA 0183. Optional video-in via adaptor 4 SONAR - CHIRP and Broadband Sonar 5 STRUCTURE - StructureScan HD - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 15
1 2 All size displays have two card reader slots. The card reader door is opened by sliding the door to the right (1) using your fingernail, then hinging forward (2) from the right hand side. Overview | HDS Carbon Installation Manual 15 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 16
drawings" on page 73. Do not mount any part where it can be used as a hand hold, where it might be submerged, or where it will -contrast screen and is viewable in direct sunlight, but for best results install the unit out of direct sunlight. The chosen Installation | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 17
the unit may cause unreliable operation and reduced service life. Exposing the unit to conditions that exceeds B 88° A 88° 7" and 9" B 88° A B 88° A B 12" and 16" 12" and 16" A Optimum viewing angle B Poor viewing angle or obstructed view Installation | HDS Carbon Installation Manual 17 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 18
fasteners. 3. Screw down the bracket (A). 4. Mount the unit to the bracket using the knobs. Hand tighten only. The ratchet teeth in the bracket and unit case ensure a positive grip and prevent the unit from changing from the desired angle (B). A 18 Installation | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 19
B Panel mounting The screws for panel mounting are included in the box. For mounting instructions, refer to the mounting template. Installation | HDS Carbon Installation Manual 19 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 20
with the smoothest flow (least bubbles) Select a transducer location The primary aim is to stay clear of propeller and hull generated turbulence, while mounting the transducer as close to the center of the vessel as possible. 1 23 4 5 20 Mounting the transducer | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 21
: Trim tabs vary in the amount of turbulence they create as they are adjusted, stay clear of these. Attaching the transducer The transducer should be installed parallel with the transom's waterline, not the bottom of the boat (deadrise). Mounting the transducer | HDS Carbon Installation Manual 21 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 22
Attach transducer to transom, using supplied transducer If the sonar image shows interference lines on the screen when moving, which worsen with speed, it may be possible to eliminate these by adjusting the angle of the transducer. 22 Mounting the transducer | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 23
at speed. If performance does not improve with tilting, try adjusting the height of the transducer relative to the transom of the boat. If the transducer is too high it may be seeing cavitation caused by the trailing edge of the transom. Mounting the transducer | HDS Carbon Installation Manual 23 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 24
Warning: The unit has a voltage rating of 12 V DC, it is not suited for use with 24 V DC systems. Warning: The positive supply wire (red) should always be connected to (+) DC with the supplied fuse or a circuit breaker (closest available to fuse rating). 24 Wiring | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 25
shown with fuse holder installed inline 5 Vessel's 12 V DC supply 6 NMEA 0183 cable Accessory wake up The yellow colored accessory wake up line may be used to control the power state of modules such wires on a common bus or to a single termination point. Wiring | HDS Carbon Installation Manual 25 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 26
Audio entertainment device (e.g. SonicHub2) 4 12 V DC negative (-) 5 12 V DC postive (+) 6 Accessory wake up line 7 Vessel's 12 V DC supply Transducer connection The unit has internal CHIRP, Broadband the unit or the section "Rear connections" on page 14. 26 Wiring | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 27
transducer cable can be connected to the 9-pin port using a 7-pin to 9-pin adaptor cable. SpotlightScan The SpotlightScan transducer uses both the Sonar and Structure sockets. Refer to the SpotlightScan manual to provide the required number of ports. Wiring | HDS Carbon Installation Manual 27 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 28
connection The NMEA 2000 data port allows the receiving and sharing of a multitude of data from various sources. 1 5 1 5 2 4 4 2 3 Unit socket (male) Key Purpose 1 Shield 2 NET-S (+12 V DC) 3 Cable plug (female) Color Drain Red 28 Wiring | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 29
cables combined should not exceed 78 m (256 ft). • A NMEA 2000 network, using Micro-C cabling, has a maximum cable length of 100 m (328 ft), between any of the backbone. Power the network The network requires its own 12 V DC power supply protected by a 3 amp fuse or HDS Carbon Installation Manual 29 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 30
0183 serial port, providing both an input and an output. The port uses the NMEA 0183 (serial balanced) standard, and can be configured in the software for different baud rates up to 38,400 baud. The NMEA 0183 cable shares the same plug as the power cable. 30 Wiring | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 31
(shield) 5 Power cable 6 12 V positive wire (red) shown with fuse holder installed inline 7 12 V negative wire (black) 8 Accessory Wake Up wire (yellow) 9 Vessel's 12 V DC supply Talkers and Listeners cable, refer to "Display accessories" on page 75. Wiring | HDS Carbon Installation Manual 31 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 32
on the unit connected to the video source. Ú Note: Both NTSC and PAL formats are supported. POWER 3 1 2 4 5 6 7 1 Video input adaptor cable (optional part) 2 RCA plug 3 Camera power cable 4 Camera 5 HDS power/data cable 6 Unit power cable 7 Data cable 32 Wiring | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 33
some fundamental setup options. You can perform further setup using the system settings option and later change settings made with the setup wizard. Time and Date Configure time settings to suit vessel location, along with time and date formats. Software Setup | HDS Carbon Installation Manual 33 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 34
the NMEA 2000 backbone are connected and are turned on. Device name Assigning a name is useful in systems using more than one device of the same type and size. When viewing data sources or the device devices have been added to the network since. 34 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 35
selections on the unit being used to the Global source settings available from other networked units. Device list The Device list shows the devices that provide data. This may include a module inside the unit, or any external NMEA 2000 device. Software Setup | HDS Carbon Installation Manual 35 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 36
to distinguish between them. The Data option shows all data being output by the device. Some devices will show additional option(s) specific to the device the RC42 illustrated above has a Calibration option, to allow easy setup of this device. 36 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 37
possible. Diagnostics The NMEA 2000 tab on the diagnostics page can provide information useful for identifying an issue with the network. Ú Note: The following information may off the bus. Rx/Tx Messages Shows actual traffic in and out of device. Software Setup | HDS Carbon Installation Manual 37 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 38
to make the information appear more stable. With damping set to off, the data is presented in raw form with no damping applied. Sonar setup Make general settings from the Sonar Settings dialog. Define Sonar sources in the Installation dialog. 38 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 39
All transducers measure water depth from the transducer to the bottom. As a result, water depth readings do not account for the distance from the transducer to the lowest point of the boat in the water or from the transducer to the water surface. Software Setup | HDS Carbon Installation Manual 39 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 40
. Select Overlay on the Structure options menu to adjust the level of structure overlay shown on the screen. You can make adjustments using the Overlay slider bar. Sonar installation Use this dialog to setup and configure available Sonar sources. 40 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 41
to the bottom. As a result, water depth readings do not account for the distance from the transducer to the lowest point of the boat (for example; bottom of the keel, rudder, or skeg) in the water or from the transducer to the water surface. Software Setup | HDS Carbon Installation Manual 41 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 42
positive value. For example, +0.5 m (+1.77 ft). For depth below transducer, set the offset to 0. Water speed calibration Water speed calibration is used to adjust the speed value from the paddle wheel to match range: 50-200 %. Default is 100 %. 42 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 43
to set a Structure depth offset for the structure transducer. This setting is in the Sonar Settings dialog. SpotlightScan This feature is enabled automatically when a SpotlightScan transducer and sensor is plugged in before the unit has been Software Setup | HDS Carbon Installation Manual 43 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 44
incorporated. This transducer has XID (transducer ID), so manual selection of the transducer is not required. Radar setup Use the Radar Installation dialog to setup the radar. Ú Note: The installation can vary depending on the radar. Follow the installation and setup instructions supplied with the - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 45
www.lowrance.com. Serial Number This number should be recorded for support and insurance select the Reset Device ID button to resolve this problem. Ú Note: This procedure must be performed with uses this value to calculate the correct STC settings. Software Setup | HDS Carbon Installation Manual 45 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 46
not all of the transmitted radar energy can be focused into a single beam by the radar antenna, a small amount energy is transmitted in 46 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 47
can be eliminated using the Sidelobe setup is required. See the operator manual for further details. After installation is completed, the NAC-1 autopilot computer (outboard motor autopilot) requires setup as described in the following sections. Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 48
used in menus and dialogs. In this context, the outboard motor acts as a rudder. Selecting data sources for the outboard motor autopilot Data sources for the outboard motor autopilot must be selected before commissioning the autopilot to ensure best 48 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 49
issues. - Check wiring connections. - Repeat rudder calibration steps. Hydraulic system calibration Virtual rudder feedback (VRF) calibration is used for vessels with hydraulic steering. 1. Select Commissioning. 2. Select VRF calibration. Software Setup | HDS Carbon Installation Manual 49 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 50
3. Follow the onscreen instructions. Ú Note: When the . Troubleshooting The following are possible symptoms or * messages displayed by the MFD. If the problem persists after trying the recommended action, contact support. connections to CAN network. 50 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 51
new source selection.) AP Depth data missing* Probable cause: Missing or invalid depth data. Recommended action: • Check the depth transducer. • Check transducer cable connections to the Misaligned potentiometer in the Helm-1. Recommended action: Software Setup | HDS Carbon Installation Manual 51 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 52
connector. • Check the alignment as per the installation instructions. AP Off course* Probable cause: • The manual steering. High drive temp* Probable cause: The NAC-1 drive output circuit is overheated due to excessive load. Recommended action: 52 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 53
circuit to shut down. Recommended action: Contact support. Low CAN bus voltage Probable cause: The CAN setup The Vessel setup dialog must be used to select the number of engines, the number of tanks and vessel's total fuel capacity across all tanks. Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 54
accurately match measured flow with actual fuel flow. Access calibration from the Refuel dialog. Calibration is only possible on Navico's Fuel Flow sensor. 54 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 55
amount used based on amount of fuel added to the tank. 5. Select OK to save settings. The Fuel K-Value should now show a Ú Note: A maximum of 8 engines is supported using Fuel Flow sensors. Fuel Level With the use of a Navico Fluid Level device connected to Setup | HDS Carbon Installation Manual 55 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 56
supported using Fluid Level devices. Ú Note: Tank data that is output by a compatible engine gateway can also be displayed, however tank configuration for such a data source is not possible from this unit. CZone setup In order to communicate with the CZone modules connected to the network, the HDS - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 57
to have the HDS Carbon set as a controller. Import and backup a configuration file The files page may be used to import CZone HDS Carbon and all connected CZone devices. For further information, see "Backing up and Importing user data" on page 71. Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 58
refer to "NMEA 2000 device upgrades" on page 70. NMEA 2000 setup Receive waypoint Select this option to allow another device capable of creating allow this unit to send waypoints to another device via NMEA 2000. NMEA 0183 setup The NMEA 0183 port must be set to suit the speed of connected devices - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 59
devices connected to the NMEA 0183 input and output. The input and output (Tx, Rx) use the same baud rate setting. Ú Note: AIS transponders typically operate at NMEA 0183-HS ( the enabled sentences. Commonly used sentences are enabled by default. Software Setup | HDS Carbon Installation Manual 59 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 60
stream is also output over ethernet, which is made available to tablet devices and PCs, using the internal wireless. The Ethernet dialogue provides IP and port data typically required for configuring on Ethernet activity, as shown below. 60 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 61
an account of the various automatically synchronised databases that ensure units are all using the same user settings and data. Each unit stores the database locally, be identified if a display does not show any other IP addresses than its own. Software Setup | HDS Carbon Installation Manual 61 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 62
" on page 70. Module network light The network LED on network expansion devices can be useful for determining if the network is fundamentally operational. No light indicates no connection. A rapidly Device Name setting. If the unit does not 62 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 63
supports instructions to manually find the device. The MFD's display is shown on the smartphone. To change the MFD's display on the smartphone, use the MFD to change the display on the MFD. The display change on the MFD is reflected on the smartphone. Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 64
menu also allows disconnection of devices that no longer require access. Wireless devices This dialog shows the internal wireless and any connected WIFI-1 devices, as well as their IP and ) Displays the name of the internal wireless network. 64 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 65
device is acting as DHCP server. Only one DHCP server may exist on a network at a time. To use two WIFI-1s as access points simultaneously the unit must initially be connected to only one unit. Once this device is selected. Select it to change the Software Setup | HDS Carbon Installation Manual 65 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 66
internal wireless is in Client Mode when the device is selected. Shows a list of all networks (hotspots) available for connection. access for GoFree store and Insight Genesis, it is necessary to use two wireless units - one must be in Client mode, the other Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 67
, dhcp_probe may be run from the HDS Carbon. Only one DHCP device may be operational on the same network at a time. If a second device is found, turn off its DHCP feature if possible. Refer to the device's own instructions for further assistance. Software Setup | HDS Carbon Installation Manual 67 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 68
the original developer of these tools, and cannot provide support related to their use. Bluetooth wireless technology The unit includes built-in Bluetooth information. Refer to the VesselView® manual or engine supplier for further information. 68 Software Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 69
. You can save the report to a memory card and email it to support or upload it directly if you have an internet connection. If you call technical support first, you can enter an incident number to assist with tracking. Check system for updates Software Setup | HDS Carbon Installation Manual 69 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 70
unit on, boot the unit, and follow the on-screen instructions. Alternatively, in the Files menu, locate the update file on when the file is highlighted. A list should appear displaying any compatible devices the update file applies to. In most cases this will Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 71
Touch, HDS Gen2, HDS Gen2 Touch, HDS Gen3, HDS Carbon, GO XSE units, Vulcan units, and ELITE Ti units). Offers most detail. • User data file version 4: Use with current units (NSO evo2/3, NSS evo2/3, NSS, NSO, NSE, Zeus, Zeus Touch, HDS Gen2, HDS Software Setup | HDS Carbon Installation Manual 71 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 72
HDS Gen3, HDS Carbon, GO XSE units, Vulcan units, and ELITE Ti units). • User data file version 3 (with depth): Use with legacy GPS chartplotters. • User data file version 2 (no depth): Use with legacy GPS chartplotters. • GPX (GPS Exchange, no depth): Use Setup | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 73
.4 mm (8.48") 132.3 mm (5.20") 83.7 mm (3.29") 32.3 mm (1.27") 146.3 mm (5.76") 165.6 mm (6.52") 238.4 mm (9.39") HDS 9 Carbon 265.0 mm (10.43") 69.2 mm (2.72") 96.5 mm (3.8") 132.2 mm (5.20") 86.1 mm (3.39") 32.2 mm (1.27") 168.9 mm (6.65") 177.8 mm (6.99") 286.7 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 74
HDS 12 Carbon 328.1 mm (12.92") 132.6 mm (5.22") 90.5 mm (3.56") 32.6 mm (1.28") 224.7 mm (8.85") 233.8 mm (9.2") 351.0 mm (13.82") HDS 16 Carbon 413.0 mm (16.26") 62 mm (2.44") 85.1mm (3.35") 129.6 mm (5.10") 93.5mm (3.68") 32.6 mm (1.28") 257.9 mm (10.15") 272.7 mm ( - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 75
Carbon video adapter cable 000-13978-001 HDS 7 Carbon bezel and card door 000-13979-001 HDS 9 Carbon bezel and card door 000-13980-001 HDS 12 Carbon bezel and card door 000-13995-001 HDS 16 Carbon bezel and card door 000-12242-001 HDS 7 Carbon suncover Accessories | HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 76
001 HDS 9 Carbon suncover 000-12246-001 HDS 12 Carbon suncover 000-13993-001 HDS 16 Carbon suncover 000-11019-001 HDS 7 Carbon gimbal bracket 000-11020-001 HDS 9 Carbon gimbal bracket 000-11021-001 HDS 12 Carbon gimbal bracket 000-13994-001 HDS 16 Carbon gimbal bracket 000-11050-001 HDS Carbon flush - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 77
/High CHIRP 000-0106-73 In-hull shoot-thru transducer, depth only 000-0106-89 In-hull, shoot-thru transducer, depth and remote temperature 000-12572-001 7-pin transducer to 9-pin adapter cable For additional transducer options, visit www.lowrance.com Accessories | HDS Carbon Installation Manual 77 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 78
9 78 Supported data NMEA 2000 compliant PGN List NMEA 2000 PGN (receive) 59392 59904 60160 60416 60928 65240 126208 Parameters, Dynamic AC input status Fluid Level DC Detailed Status Battery Status Inverter Status Speed, Water referenced Water Depth Supported data| HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 79
Part A AIS Class B Statis Data Report, Part B Route and WP Service - WP List - N&P Wind Data Environmental Parameters Environmental Parameters Temperature Humidity Data Group Entertainment - Library Data Search Entertainment - Supported Source Data Supported data| HDS Carbon Installation Manual 79 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 80
- Supported Zone Service - WP List - N&P Wind Data Heading / Track Control Vessel Heading Magnetic Variation Speed, Water Referenced Water Depth Distance Log Position, Rapid Update COG & SOG, Rapid Update GNSS Position Data Cross Track Error 80 Supported data| HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 81
DOPs GNSS Sats in View Route and WP Service - WP List - N&P Wind Data Environmental Parameters Environmental Parameters Temperature Direction Data NMEA 0183 supported sentences TX / RX - GPS Receive DBT DPT MTW VLW VHM DBT DPT MTW VLW VHM Supported data| HDS Carbon Installation Manual 81 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 82
TX / RX - Compass Receive HDG HDT HDM Transmit HDG TX / RX - Wind Receive Transmit MWV MWV MWD MWD TX / RX - AIS / DSC Receive DSC DSE VDM Ú Note: AIS sentences are not bridged to or from NMEA 2000. 82 Supported data| HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 83
list is available at: www.lowrance.com HDS Carbon technical specifications Approvals Compliance FCC, Industry Canada, Radio Equipment Directive, ACMA, RSM Display Resolution HDS-7 1024x600 HDS-9 1280x720 HDS-12 1280x800 HDS-16 1920x1080 Type SolarMAX HD (TM) IPS technology Brightness >1200 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 84
cycles of 20 G GPS 10Hz high speed update. GPS & GLONASS. WAAS, MSAS, EGNOS Interface Ethernet HDS-7 1 Port HDS-9 2 Ports HDS-12 2 Ports HDS-16 2 Ports NMEA 2000 Micro-C (1) NMEA 0183 input/output. 4800, 9600, 19200, 38400 baud 84 Technical specifications| HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 85
"Dimensional drawings" on page 73 Weight (display only) HDS-7 1.13 kg (2.49 lb) HDS-9 1.55 kg (3.42 lb) HDS-12 2.44 kg (5.38 lb) HDS-16 3.60 kg (7.94 lb) Mounting type Bracket ( Period 2 Year + part of the 5 year upgrade program Technical specifications| HDS Carbon Installation Manual 85 - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 86
86 Technical specifications| HDS Carbon Installation Manual - Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 87
- Lowrance HDS-12 Carbon - No Transducer | Installation Manual - Page 88
*988-11265-002*
ENGLISH
HDS Carbon
Installation Manual
www.lowrance.com